Coal - Moss No. 3 Mine: The Materials Handling Aspects

A large reserve of thick coal in southwest Virginia was developed by Clinch-field Coal Co. in 1957-1958 to produce a nominal rate of 1500 tph raw coal. Operation features coal cleaning in transit. Refuse removed averages 35 pct. Evolution of plant from initial conception to completion is discussed, selection of means applied is explained, and performance to date us design expectation is described. The long-range plan calls for ultimate handling capacity of 40,000 tpd raw coal with anticipated clean coal capacity of 26,000 tpd on a three-shift basis. From a materials handling viewpoint, the Moss No. 3 operation is principally of interest as an ensemble. Generally speaking, it uses time-tested equipment and ideas but some of these are employed on a scale that may be new in the industry. At present about 20,000 tpd of raw coal are being handled. This is expected to increase to 40,000 tpd as soon as business conditions justify it. The purpose of this paper is to discuss the evolution of the plant as to materials handling practices, to describe briefly the equipment and methods used, and to comment on performance in certain areas. The subject divides itself naturally into four phases: 1) operations at the mines, 2) transportation from mines to plant, 3) raw coal handling into the plant, and 4) transportation of refuse away from the plant. OPERATIONS AT THE MINES The coal reserves for Moss 3 are in southwest Virginia where Dickenson, Russell, and Buchanan Counties come together. This area contains about 15 square miles and over 100,000,000 tons of coal. Here the No. 4 (Tiller) and No. 5 (Jawbone) seams of the Norton Formation lie so closely together that for practical purposes, they constitute one seam of coal. This seam, which is called the Thick Tiller, varies from 10 to 18 ft in thickness and underlies Sandy Ridge, a mountain cresting between 2400 and 3300 ft above sea-level. At 18-ft seam height (which is considered to be the maximum practical mining height) the parting between seams will be about 3 1/2 ft thick and each bench of coal will be about 7 ft thick. Depending on the amount of impurities in the seams Drover. total reject in this height coal may approximate 50 pet by wt. It will average about 35 pet for the property as a whole. The first move in developing this resource was made in 1953 when contour maps of several square miles around Duty, Va., including all the known outcrop, were made by photogrammetry. At this time, it was felt the prospective operation would be served by the Clinchfield Railroad and a photogrammetric route survey was made by this railroad from Haysi to Duty. Study of the resulting maps indicated only one site—adversely owned—which might accommodate the size washing plant to be erected. Water resources of a dependable nature seemed nonexistent. In 1954 bulk washability tests were made on the Tiller Bench at the Moss No. 1 preparation plant. The tests indicated this portion of the seam, mined separately, would wash to 4 pet ash with good recovery. Also in 1954, development of Moss No. 2, south of Sandy Ridge, was begun. This mine is in the Tiller Seam where it is about 100 ft below the Jawbone Seam. The reasons for developing a mine in the normal Tiller Seam before tackling the Thick Tiller seemed compelling: Railroad service could be established quickly, communications were better (though not good!), more was known of the seam (it had been mined in the years 1911 to 19241, and there was no essential property to be acquired. After some legal skirmishing, the Norfolk & Western Railroad was granted the right to serve the new mine. Three decades earlier the old mine had been served by the Clinchfield Railroad. The event which triggered active development of Moss 3 was the Appalachian Power Co.'s decision in 1956 to build a 450,000-kva power plant on Clinch River at Carbo. This solved the problem of marketing the steam coal which inevitably must be a product of a mine in the Thick Tiller. Management promptly decided to build the preparation plant at Carbo where an excellent site was owned; where railroad service existed; where telephone service could be obtained; and where roads, bridges, and water supply were tolerable.