Extractive Metallurgy Division - Hurley Furnace and Boiler Description and Design

THE usual reverberatory system of smelting cop--1- per concentrate or calcine has for its component parts a furnace and one or two waste heat boilers. These parts are operated on a basis of compromise, since the furnace can send gas to the boilers at too high a temperature and the boilers by plugging, due to dust or slag, can place a definite limit on the amount of fuel the furnace can burn. Over the years the copper concentrate smelting furnace has had few advances in design. The simple rules of design such as the flame should wipe the bath and the speed of the gases should be reasonably low for dust carrying purposes seem to cover the main features. In the construction of the individual furnaces some innovations are always being introduced. Among these are charging so that the work of smelting is a complete bath process, the use of suspended brick arches in place of sprung arches, the use of basic brick, not only in the crucible, but also in roof and sidewalls, the use of various means to feed the charge, the use of magnetite or other heavy material to construct the hearth, water cooling of bridgewall and slag skimming bay, the smelting of raw charge instead of calcine, the use of preheated air, and possibly the use of oxygen-enriched air for combustion. But the general outlines of the furnaces have not changed much except as to size. Furnaces at Hurley As shown on Fig. 1, the furnace at Hurley is 126 ft long between the longitudinal buckstays and 32 ft wide at the skewback plates. The foundation is a concrete retaining wall with piers at intervals that go deeper into the earth. Purposely the wall at the burner end of the furnace is not backed-up as tightly as the other parts of the foundation so that movement due to expansion may take place here rather than into the boiler foundations. Within these foundation retaining walls of concrete, the earth has been removed to allow the placement of the crucible brick base inside of which a silica hearth is laid 4 ft 6 in. in depth. No expansion is left in the brick base and crucible where they are in contact with the hearth. The hearth itself is of quartzite crushed to 1 in. size with fines left in the product. An 8 in. layer is laid and tamped with paving tampers to about 6 in. in thickness. Then a layer of silica flour is spread and vibrated into the hearth. This operation is repeated until a depth of 4 ft 6 in. is occupied by the silica mass onion-skinned in layers of approximately 6 in. Before firing the entire hearth is covered with broken slag to a depth of 4 in. so that a seal may be formed on the hearth. The crucible is completely faced with magnesite chemically bonded brick while the outside, against the foundation, is made of silica brick. The side-walls are carried up with silica brick in which expansion joints are left at intervals. Above the crucible the sidewall is corbelled to form a shelf on which the charge may build up along the side-walls, see Fig. 2. The arch of the furnace is sprung 20 in. silica brick, with the longitudinal centerline horizontal the length of the furnace, and some 9 ft in the center above the bath. Both straight and wedge brick are used in the construction and a thin silica mortar is troweled for joints. After the arch under heat has assumed its permanent shape, a silica slurry is spread over the arch to fill any cracks that have formed, thus giving bearing surface to the brick and preventing dust from entering the body of the arch to act as a future fluxing agent. The uptake of the furnace slopes up to the boiler entrance where a brick pilaster divides the gas stream for the two boilers. Over this flared uptake is a suspended flat arch of firebrick. The pilaster and sidewalls are constructed of firebrick but the bottom of the uptake is lined with silica brick and fettled through holes in the roof with siliceous fettling. Close to the entrance of each boiler is a brick covered slot through which water-cooled dampers may be lowered in event of boiler trouble. These water-cooled dampers are hung permanently in position ready to be lowered when needed. Flexible hoses to follow the dampers as they are lowered are connected at all times and individual chain blocks are used to lower the dampers. A pump supplying water is started before the dampers enter the heat. Charging of the furnace along the sidewalls for some 80 ft from the bridgewall is accomplished by electric vibrating conveyors fed by belt from charge storage bins above the furnace. These conveyors