Factors Influencing Selective Flocculation-Desliming Practice at the Tilden Mine (18d5713b-0751-4800-b56b-be99b6708fab)

Introduction The large reserve of fine grained oxidized iron-formation at the Tilden mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Due to the nonmagnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden, ore body have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of desliming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions. Development of selective flocculation-desliming was a key to commercialization of the process. Operations started in late 1974 with Algoma Steel Corp. Ltd., J & L Steel Corp., The Steel Company of Canada Ltd., Wheeling-Pittsburgh Steel Corp., Sharon Steel Corp., and The Cleveland-Cliffs Iron Co. as participants. Cleveland-Cliffs operates and manages the operation. Development of the Tilden Flowsheet The geology and ore reserves of the Tilden mine have been detailed in a paper by Villar and Dawe (1975). A joint program was undertaken in 1961 with the US Bureau of Mines in Minneapolis using the flowsheet developed by the Bureau employing the selective flocculation-desliming and calcium activated anionic silica flotation method (Frommer, et al, 1966; Frommer, 1964; Frommer, Wasson, and Veith, 1973). During this time, parallel testing at Cleveland-Cliffs Research Laboratory and Pilot Plant centered on the same type of desliming but was followed by the cationic flotation of silica with amine collectors (Columbo and Jacobs. 1976). The cationic silica flotation system was eventually chosen for its overall efficiency and simplicity. Regardless of the flotation method chosen, the technique of selective flocculation-desliming prior to flotation is the key to the success of the process. The flowsheet is described in detail by Villar and Dawe (1975). [Figure 1] shows a simplified one-line flowsheet of the Tilden concentrator. A total tailings thickener has been added to the original flowsheet and was placed in operation in 1978. The total-tailings thickener overflow reports to the reuse water pond and the underflow is pumped approximately 8 km (5 miles) to a storage basin. A flowsheet of the reuse water system is shown in [Fig. 2]. Selective Flocculation-Desliming Data have been published on the mechanisms and factors affecting selective flocculation in iron oxide-silica systems. The intent of this paper is not to discuss the theoretical aspects of selective flocculation, but rather to present experience gained from the commercial Tilden operation and from bench and pilot plant testing of fine-grained oxidized iron ores. From the bench and pilot plant testing prior to plant startup, certain reagent combinations and rates for the commercial Tilden plant were established. In the experience gained from three years of plant operation at Tilden, some of these reagent dosage rates have required significant adjustments due to changes in reuse water quality and to meet the requirements of varying ore types. Reuse Water The process water quality is a major concern at the Tilden mine and is constantly being monitored for selected chemical and physical characteristics. This monitoring has continued on a regular basis in order to gain a more thorough understanding of the interactions taking place in a dynamic water system and particularly as water quality is influenced by seasonal variations. Control of the reuse water chemistry is essential to the Tilden process both in the selective flocculation-desliming and flotation stages of concentration. With roughly 75% of the reuse water used in grinding-desliming operations, it is readily apparent that the biggest "reagent" in the selective flocculation-desliming process is water. Not enough can be said about the close control that must be exercised on the overall reuse water system. Control of the chemical treatment of the feed to the total tailings thickener is of utmost importance in order to produce a reuse water for the concentrator that is compatible with all stages of the concentrating process. There are many analyses made which aid in judging the quality of the water. Some of these are shown in [Table 1]. Five are particularly important and are monitored daily so that reagent adjustments can be made as required: suspended solids, calcium hardness, pH, dissolved silica concentration and temperature.