Institute of Metals Division - The Vapor Pressures of Zinc and Cadmium over Some of Their Silver Alloy

The fundamental problem in the thermodynamics of solid solutions is the determinatiorl or calculation of the activities of the components as a function of temperature and composition. Since the theory of metals is not suficiently developed to allow a priori calculation of these quantities, they must be obtained from experiment. C. Wagner1 has reviewed the literature of this subject for the period before 1940. Although several important and extensive studies have been made in the meantime, the number of systems to which any sort of quantitative information can be assigned is vanish-ingly small. These data have become of great potential importance in studies of the structure of solid solutions2 and intermetallic compounds, the nature of the diffusion process,3,4 and perhaps even the mechanism of mechanical deformation.5 For these reasons, it. seems very worthwhile to extend the experimental data in this field. Although there is little use in duplicating Wagner's review, attention should be directed to the most recently reported investigations. A brief enumeration of the methods of measurement previously employed also should be valuable. The most direct method is the determination of the partial pressure of the components in the vapor phase in equilibrium with the solution. Both equilibrium and kinetic methods have been tried in metal systems, but almost exclusively on liquid phases. Only in the ease of carbon in iron alloys and in the copper-zinc system have extensive measure- ments been made which include solid phases. When one of the components is an element, such as nitrogen or carbon, which forms compounds which are very volatile and stable at normal temperatures and pressures (CH4, Co2, CO NH3), it is frequently possible to equilibrate mixtures containing these (such as CH4-H2, CO2-CO, NH3-H2) independently with the elernents (C, X) and with the metal (Fe, Ni, etc.). Such measurernents have been made for carbon in iron, iron-silicon, and iron-manganese alloys by Smith6 and in iron and iron-nickel alloys by Toensing.7 Differences between carbon activity values at the same temperature and carbon content when carboil is introduced from CH4-H2 rnixtures or CO-CO. mixtures indicate that the effects of hydrogen and oxygen in the system are not negligible, and one can only hope that the true value lies somewhere between these sets of results, probably nearer the CH4-H2 data since hydrogen is less soluble in iron than oxygen. This is essentially an equilibrium method, although flowing gas is employed. A kirletic method has been employed which consists of sweeping an inert gas (generally hydrogen) over the alloy at a series of rates, condensing the metal vapor out,, and analyzing it. The metal content can be extrapolated to zero flow rate (equilibrium). Wejnarth's8 work on Cd-Mg and Zn-Mg is a good example of this frequently used method. A variant of this consists of equilibrating a known volume of inert gas with the alloy, sweeping it out quickly, and analyzing for metal. In common with the above method, it has the disadvantage that the "inert" gas is generally somewhat soluble in the alloy. Moreover, the former continuously displaces the system from equilihrium and may give low values if solid diffusion is involved. The dew point method applied by Hargreaves9 to the alpha and beta brasses and by Schneider and Stolll0 to A1-Zn avoids the introduction of another component to the system, but is useful only in systems in which one component is much more volatile than the other. The alloy sealed in one end of an evacuated silica tube is heated to the desired temperature. The temperature of the other end is lowered until droplets of the volatile component condense. When the temperature is raised slightly, the droplets will evaporate. By careful adjustment of temperature, the range between evaporation and condensation can be narrowed appreciably. An independent determination of the vapor pressure of the . pure volatile component is necessary to give the partial pressure over the alloy. This is the method employed here to determine the vapor pressures of zinc and cadmium over their silver alloys up to 34 pct in cadmium and 76 pct in zinc. The former involves only the a solid solution, but the latter covers the a, ß, y, and e fields. In recent determinations, Herbenar, Siebert, and Duffenbarkl1 used the