Minerals Beneficiation - Analysis of Variables in Rod Milling

SEVERAL constructive and fundamental studies have been made in the analysis of data obtained from experiments carried on with batch ball and rod mills. The operating characteristics of ball milling in small continuous circuits have also been appraised. It is from these analyses that some of the theories of comminution have been developed. Relatively few studies of continuous rod milling have added significantly to the fundamental concepts, because seldom have they yielded sufficiently consistent results. Perhaps they have been too limited in their scope. Careful control of the variables in batch grinding is simple compared with that encountered in a continuous operation. This factor alone has discouraged many investigators. Occasionally results of systematic changes made in industrial rod mill circuits have been published, but usually the data are sketchy and are restricted because of the unwieldiness of the equipment used. The work, in general, has not been comprehensive; nevertheless it has provided empirical relationships that have bridged the gap between postulate and practice so that by proper manipulation of formulae, a mill designer can anticipate mill size and power requirements.14 Although operating variables of a small continuous mill are not so easy to control as with the batch mill, with present day devices, and with careful experimental work, consistent results can be obtained. Nearly four years ago, in the Process Laboratory, Allis-Chalmers Mfg. Co. began a systematic study of the effects of several variables upon the performance of the pilot rod mill. A mill was built in the laboratory to provide the versatility required for the proposed study. It was constructed in sections so that it could be operated, with a few modifications, as a rod mill 30 in. x 8 ft or 30 in. x 4 ft. The discharge end of the shell was flanged so that either an end peripheral discharge or an overflow discharge could be installed. Thus the performance of at least four types of mills could be studied merely by changing the type of discharge or the length of the mill shell. The grinding experiments were designed so that a study could be made of the way in which the mill speed, feed rate, and pulp density influenced the performance of both overflow and end peripheral discharge rod mills. Four sets of experimental data were collected from the four mill arrangements. The mill in each set of experiments was fed at four rates of feed depending on the length of the mill, at four pulp densities, and at five percentages of critical speed. Electrical and mechanical controls were in- stalled to regulate all these independent variables, and auxiliary devices were used to verify the precision of the controls at each point. The dependent variables used to quantify the experiments were the reduction ratio and the hew surface area produced as calculated from sieve analyses. These were incorporated with the energy factor by the calculation of both the new surface produced per unit of energy and the Bond work index.' Rod wear, as a dependent variable, was not studied because of the short period of operation for each run. Exclusive of repeat runs, each set of experiments yielded 80 products, and the total study at least 320 products, all of which were quantified. With the operating information collected, these data presented a bewildering accumulation. Statistical analysis has been invaluable in unraveling the confusion and in presenting a means of establishing the nature and the magnitude of the significant variables. Data presented in this paper are those from the 30 in. x 4 ft end peripheral discharge rod mill, Fig. 1, when limestone was ground at feed rates of 1000, 2000, 4000, and 5000 lb per hr, at pulp densities of 50, 60, 70, and 80 pct solids, and at mill speeds of 50, 60, 70, 80, and 90 pct of the critical speed. These 80 tests have all been run at least twice, and occasionally a third time, to prove that the data obtained were reproducible. The techniques of operation and the methods of quantification of results are described in the following pages and the results analyzed statistically to show the significant variables. The variables are plotted to show the relationships that exist. A massive dolomitic limestone from Waukesha Lime and Stone Co. was used for feed during these experiments because of its availability and its tex-tural uniformity. This limestone analyzed 28.7 pct CaO, 21.0 pct MgO, 6.0 pct SiO2, 0.4 pct A1²O³, and 0.3 pct Fe²O³ and had a loss on ignition of 44.1 pct. It had a rod mill grindability at 14 mesh of 9.6 grams per revolution from which a work index of 13.9 was calculated. The ball mill grindability at