Minerals Beneficiation - Analysis of Variables in Rod Milling. Comparison of Overflow and End Peripheral Discharge Mills

IN a previous article' the authors outlined a study of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam .opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report' were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated. Data from the second series are recorded in Table I. Listed in the first three columns are the independent variables of feed rate (1000, 2000, 3000, 4000, and 5000 1b per hr), mill speed (50, 60, 70, 80, and 90 pct of critical), and pulp density (50, 60, 70, and 80 pct). The dependent variables, Pso, P100, reduction ratio, slope of the log-log sieve analysis curve, power demand, and Bond work index follow. Of these, only the reduction ratio and the Bond work index were analyzed for significance. Production of new surface as calculated from sieve analyses has not been included for this series because of the questionable assumptions that have to be made to satisfy the formulas involved. The large number of products obtained during the runs precluded the use of surface measurement techniques by the gas adsorption methods at this time; however, samples of all products have been stored for future reference. To test the consistency of the reporting of the sieved products, an averaged sieve analysis was calculated from the wet-dry plots obtained from the three product samples of each run. The resulting averaged analysis was plotted and the P80, selected. The relative deviations of the P80's from each of the three product samples with respect to the P80 of the averaged analysis were then calculated. In only two sets were the relative deviations (6.2 and 9.9 pct) considered excessive. In each of these two sets, one sieve analysis was obviously out of line; hence that analysis was ignored and new averages were computed. This reduced the relative deviations to 1.2 and 2.7 pct respectively. The relative deviations of the product analyses with respect to their averages ranged from 0.1 to 1.4 pct at 1000 lb per hr, 0.0 to 1.1 pct at 2000 lb per hr, 0.2 to 3.0 pct at 3000 lb per hr, 0.3 to 4.3 pct at 4000 lb per hr, and 0.5 to 5.2 pct at 5000 lb per hr. The relative deviation of the 80 pct passing point for 96 dry sieve analyses of the feed with respect to that of the averaged analysis was 7.6 pct. This slightly higher percentage can probably be attributed to a greater proportion of tramp oversize in a crusher product than is ordinarily found in a rod mill product. The last column on Table I lists the adjusted work index, which has been used as the measure of efficiency for the various combinations of operating conditions investigated. Efficiency increases as the index becomes lower. It was reported in the previous paper that the work indexes for the Waukesha limestone used in these experiments decreased as the product size decreased (as calculated from Bond grindabilities). That is, this limestone becomes easier to grind as the material becomes finer. This is unusual, because the work index for most materials as calculated from the Bond grindability has remained constant as the product size decreased or has increased slightly. Table II lists the results of Bond grindability tests at all mesh sizes from 3 to 200 and the work indexes calculated from them. To remove this variation of work index with product size from the data so that results would apply to any material of constant work index, the work index values shown in Table II were plotted against product size on log-log paper. From this curve (a straight line function in this case), the expected work index for the product size for each of the runs of the experiment was obtained. The work indexes as calculated from the reduction ratio and energy consumption were then divided by the corresponding expected work index. The results obtained are reported in percentages on Table I as adjusted work index and are actually percentages of the work index for the Waukesha limestone at the size in question. Multiplication of the work index value for a material of constant index by these percentages should allow the application of the adjusted work index curves to the material. Only the adjusted work index values, not the actual experimental values, were used for the variance analyses and for the graphs.