Search Documents

By Henry Chumienski

Next to the paper industry, the steel industry is a major user of water. Without an adequate and reliable source of “good” water, steel cannot be produced. The use of water has a direct impact on steel quality and on our environment. Used improperly, water can also add unnecessary costs. Used properly, water can maintain and improve steel quality, enhance our environment and control or reduce the “total cost of operation”. Water needs to be more than just “wet and not lumpy”. Water quality needs to be based on the end use. This paper discusses ways to manage many of the water systems. With little or no capital investment it is possible to develop operating practices that protect your initial investment, ensure that the water systems do not have a negative impact on quality or your production costs and also minimize your chance of having an environmental incident.

Jul 30, 2018

By Ulrich Sommers

The Intelligent Furnace (I-Furnace) by SMS group is a smart furnace process and production optimization model. The combination of various tools leads to an optimized heat treatment and production process. It combines a mathematical/physical model to control the furnace with EMG’s IMPOC system for online strength measurement and a newly developed annealing microstructure model to predict material properties. This paper reports about the revamping of an existing galvanizing line, where a mathematical/physical control model has been implemented in combination with an online quality measurement system. This way, the process improvement of continuous galvanizing lines and the quality management of a range of steels including AHSS will be demonstrated. Furthermore, it gives information about the development of the annealing microstructure model to predict material characteristics. Eventually, the I-Furnace will be presented according to the current development and reference status.

Oct 30, 2017

By Maciej Korecki

Pyrowear®Alloy 53 steel is an excellent material for the construction of drive transmission components (gears, shafts, etc.) which have to operate in difficult conditions primarily in the aviation industry (Fig. 1.). Among the properties of such items is a high case hardness and abrasion-resistance, while the core remains flexible and is capable of carrying large impact loads. They can work at elevated temperatures with limited lubrication. The thermal treatment of such materials is based on case hardening by means of carburizing. This paper presents the technology of vacuum carburizing of Pyrowear® Alloy 53 steel. It discusses the methods of establishing different profiles of carbon concentration in a layer and their influence on the hardness profile. The effects of sub-zero treatment and tempering on the properties of the hardened case are also considered. It also presents a SimVaC® simulator of vacuum carburizing, designed especially for Pyrowear® Alloy 53 steel, which provides highly accurate predictions of the outcome of the process as the profile of carbon concentration in the layer, or vice versa: establishes the process parameters which will guarantee the required profile.

Aug 16, 2017

By Andreas Volkert

Energy efficiency, equipment reliability and cost reduction are of the key factors in any efficient plant. Badische Stahlwerke (BSW) started using its own burner technology in 2001, this was developed by Badische Stahl-Engineering (BSE). Over the past 15 years, Badische improved all aspects of its Virtual Lance Burner (VLB), to perfectly fit all steelmaking requirements. This tiltable VLB was first tested at BSW’s electric arc furnace no. 2 in 2012. Promising results like reduction of refractory wear, energy efficiency, reliability, etc., were obtained. At the same time the existing VLB system was further improved with regards to the design of the water-cooled copper box. Today in 2016 both EAFs at BSW are equipped with the new patented tiltable system and the new copper box design. The paper will describe the results of the past years at Badische, but will also show the performance at other installations.

Aug 17, 2017

By Márcio Corrêa de Carvalho

Welded deposited chromium carbide overlay’s has been widely used in various branches of welding overlay’s industry related to wear. Characterization techniques are an important tool in the development of chromium carbide overlays resistant to wear, enabling the identification of phases, constituents and defects. In this work one used optical microscopy, scanning electron microscopy and energy dispersive spectroscopy on chromium carbide overlay’s deposited by submerged arc welding process. The characterization techniques identified precisely the elements of the overlay’s enabling point of the main cause of the observed defects such as cracks, porosity and clusters of particles known in the industry as " rice crispy" .

Aug 16, 2017

By Luciana Lezira Pereira de Almeida

With the increasing use of ornamental rocks, mainly in civil construction, sundry problems were identified in relation to rocks cutting, such as efficiency in the cutting process and rock quality lumber. In recent years several composites have been developed to solve these problems. In this context, the study of the binomial matrix metal-diamond interaction is of paramount importance for the development of new composite materials to improve the efficiency of the cutting tool. The diamond impregnated matrix metal often reveals a reaction between the diamond surface and the matrix. Besides the mechanical connection, chemical reactions can sometimes occur. Therefore, this study aims to assess the achievement of diamond composites in the system Fe / Cu / Ni / Sn via powder metallurgy, with added CRB2. Analyzes have been performed to characterize chemical / physical and mechanical. The results have showed that addition of CRB2 promote significant changes in the properties of composites, especially in wear resistance and fracture toughness. Furthermore, the presence of the composite CRB2 causes a significant improvement in thermal stability.

Aug 16, 2017

By Michael Brandner

HSM can be divided into different groups such as Conventional HSM with Roughing stands and HSM without Roughing stands = Mills with just finishing stands. The roll requirements for different stands are quite different. In Roughing stands the temperature of the slab is very high. Therefore the resistance against thermal wear/fatigue is the most dominating factor. Today mostly Chrome Steel, Semi HSS and HSS rolls are applied. A comparison and evaluation of such rolls will be described. In the finishing mill the tendency/wish is to use HSS rolls in all the stands. The grade HSS is defined by at least a certain amount of carbide forming elements such as V, W, Mo, Nb etc. The matrix and other precipitations can be adjusted according to the need and situation in the mill. In the pre-finishing stands the HSS is already well introduced. In the last finishing stands the original HSS tended to stick and the cobble rate increased. New development decreased the problem and gave some very promising results. In the last finishing stands beside the high performance a higher resistance against incidents is needed. Solutions in this direction including e.g. residual stresses and special core material will be discussed. Proper testing and grinding procedures can avoid losses and reduce the TCO. Data sourcing and evaluation in regards of rolling and grinding is the key for the optimization of the TCO. Several examples and comparison between different applications will be given in detail and explained. Future possibilities will be discussed as well as results of latest trials in mills.

Aug 17, 2017

By Cristina Escudero Martinez

The purpose of the Basic Oxygen Steelmaking (BOS) is to refine the hot metal produced in the blast furnace into raw liquid steel, which may be subsequently refined in the secondary steelmaking shop. Appropriated fluxes for the BOF could require low melting point to reduce the energy consumption, to reduce the energy to fluidity the slag at lower temperature and to melt at lower temperature than steel. It is necessary a good Tumble test result and the fluxes do not generate fines which could obstruct the blowing plugs, so we would have a homogeneous flux. A homogeneous chemistry that allows to control the basicity (Si and MgO levels) and a high absorption characteristics to combine the flux with P, S, Si, etc. are necessary. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification being olivine and serpentine its principal minerals. It is formed by orthopyroxene, clinopyroxene and olivine in variable proportion. Dunite is a very homogeneous and hard stone. The main characteristics are: High hot and cold resistance to mechanical stress (shatter / crushing / abrasion), softening and melting points of a flux, not a refractory material, large porosity which is increased more than 20% when dunite is heated at BOF process temperature, and high absorption level, and stable components with low melting points. PASEK Dunite is a good flux in BOF process and its use is recommended if the BOF process produces pig iron with low Si content, generates high levels of slag and it is necessary maintaining the basicity index and the MgO amount and with high value of hot metal ratio (high amount of phosphorus to remove).

Aug 16, 2017

By Daniela Mota Paschoal Veloso da Silva, Gabriel Filinkoski, Suelen Silva Rocha, Jorge Luiz Valença Mariz

A previsão da fragmentação da rocha é essencial para otimizar a operação de desmonte de rochas. A fragmentação depende de muitos parâmetros, como propriedades estruturais e geomecânicas do maciço rochoso, geometria do plano de fogo das detonações e propriedades dos explosivos. Neste contexto, este trabalho objetivou realizar a previsão da fragmentação por simulação do desmonte de rochas da Mineração Megaípe considerando as características estruturais e geomecânicas inerentes à formação do maciço rochoso através da metodologia de Kuz-Ram. A metodologia consistiu no levantamento das propriedades geométricas das descontinuidades visíveis na face da bancada existente, realização da classificação geomecânica através dos sistemas Rock Mass Rating (RMR) e Q e aplicação dos resultados para predição da distribuição granulométrica da fragmentação. Obteve-se como resultado da simulação que cerca de 90% do material fragmentado deve passar na abertura do britador primário disponível na pedreira, além de resultados favoráveis quanto às análises de condições de estabilidade do talude operacional.

Oct 3, 2019

By Kenneth Holmnerg

About 100 million terajoule is used annually worldwide to overcome friction and that is one fifth of all energy produced. The largest quantities of energy are used by industry (29%) and in transportation (27%). Based on our recent studies on energy use in passenger cars, trucks and buses, we concluded that it is possible to save as much as 17.5% of the energy use in road transports in the short term (5-9 years) by effective implementation of new tribological solutions. This equals to annual energy savings of 11.6 exajoules, fuel savings of 330 billion liters and reduction in CO2 emission by 860 million tonnes. In a paper mill, 15-25% of the energy used is spent to overcome friction. The electrical energy used by a paper machine is distributed as 32% to overcome friction, 36% for the paper production and mass transportation, and 32% is other losses. In paper machines, 11% of the total energy used to overcome friction can be saved by the implementation of new tribological technologies. This would result in electrical energy savings worldwide of 130,000 terajoule, economic cost savings of 2 billion euros and CO2 emission reduction of 11 million tonnes annually. An overview of the total energy saving potential by improved tribology in transportation and industry is presented.

Jul 31, 2018

By Beatriz Pereda, Ana Clara Fonseca da Silva, Tiago Seixas Bittencourt

Reinforcing steel bars are usually specified based on mechanical properties with flexibility in chemical composition and processing. Most developments, in these steels, are normally focused on alloy and process design to reach minimum cost and conformity to specification. Processing routes using quenching and self-tempering (QST) and accelerated cooling are the most common. Microalloying with V and Nb have been used in rebar. When acicular constituents must be avoided, a combination of Nb microalloying with judicious control of cooling is one of the preferred options. Niobium can contribute to improvement in tensile properties through austenitic grain size control during hot working, precipitation hardening due to carbonitrides or clusters, and hardenability increase. In the present work the alloy design and development processes of a Nb microalloyed steel for rebars are presented. The designed steel has fulfilled the required specification and is under regular production. Austenitic grain size refining – when comparing with the “basic composition” normally used was observed, even without any change in the thermomechanical processing cycle. There are indications that precipitation hardening may also occur. Results indicate that Nb is a good alternative as a microalloying element in rebars.

Oct 1, 2019

By Pietro Palma

Universal cardan joints are widely used in drivetrains of rolling mills for steel and aluminum making, as well as for non ferrous alloy industry. Working conditions are extremely tough due to high alternating or pulsating rolling torques in the roughing stands and high torques and speeds in the finishing stands. Overloads and lubrication along with oxide and slag are also critical issues that contribute to create severe working conditions. For a constant and reliable power transmission rolling mills performance and uptime rely on Universal cardan Joints which are the most critical equipment of the drivetrain. Fatigue assessment of the most important components of the Universal cardan Joint is therefore definitely vital for the mill in order to avoid failures and consequently downtimes. Considering the component’s dimensions and weight and in addition the time needed in order to reproduce full scale tests, a new approach to study the Universal cardan joint’s main components fatigue behavior has been investigated. It consists in reproducing the local stress condition of the main joint components on small scale specimens that can be tested by conventional laboratory fatigue machines. The aim of this study is to analyze the most critical stress concentration areas in the universal cardan joints highlighting how a universal cardan joint Wöhler curve can be determined through laboratory tests of small scale specimens.

Aug 16, 2017

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Jim Belous

Fluid Dynamic Modeling (FDM) was used to develop solutions how to eliminate the fugitive emissions from the meltshop building and to comply with the EPA “6% opacity from the furnace operations” rule. Secondary Emission Control (SEC) system performance was simulated by an inverted 1:96 scale Plexiglas model of the entire meltshop, utilizing the negative buoyancy effects of saline solution in water. Test results show that with the installation of the internal partition wall which separates furnace aisle from the caster aisle, significant improvement of the SEC system is achievable, thereby avoiding large expenditure for the expanding a fume collection system capacity.

Aug 17, 2017

By Jan Lampke

Increasingly pelletizing discs are used for the recycling of dust and sludge. The applied pellet feed is highly variable, for example in terms of chemical composition, grain size distribution and raw density. These raw materials related factors lead to a destabilized pelletizing process, which initially must be homogenized through special mixtures, as well as the use of binders or additives. There are many possibilities to reach stringent restriction of material related target factors. On the one hand it is helpful to be flexible by changing the process parameters of the pelletizing disc. On the other hand, it is necessary to use a material-binder-formulation, which leads to a highly stable pelletizing process. The paper deals with an example of the use of agglomerating device, pelletizing disc, to prepare different dusts and sludges for material recycling. These dusts und sludges are mostly generated in metallurgical processes, e.g. sinterplant, blast furnace and steelworks.

Aug 16, 2017

By Dennis Travagini Cremonese

In the early stage of front end studies of an Iron Ore Project, the sizing of surge capacities and stockpiles are normally assumed based on the experience of the study team. Understanding and sizing of these capacities at the early stages of the project are important for future stages of the project as drastic changes in sizes will impact the economics of the project at that stage. An innovative user configurable high level dynamic modeling tool has been developed to assist in speedy evaluation of assumptions made by the study team. This model incorporates systems or facilities that are commonly used iron ore project from mine to port. This model includes subsystems that will simulate all the logistical components, major process plant systems required for an Iron ore project. The output data provided by this high level dynamic simulation tool will enhance the confidence level of engineering carried out during the early stage of the project. This paper discusses the innovative tool capabilities and a test case comparing various techniques used in iron ore project front end studies.

Aug 1, 2018

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018

By Frank Schrama

The Steel Plant Model (SPM) is an advanced logistic simulation model for steel plants. With the SPM, bottlenecks can be solved and logistics can be optimized. Both existing plants and greenfield designs can be simulated. All movements and actions simulated, from hot metal to cast products. Not only all major equipment and their relevant components (like a sublance) are simulated, but also ladles, scrap boxes, transfer cars and cranes. The whole plant is simulated in 3D and actual distances and speeds determine transport times. The SPM includes process time deviations and equipment downtimes for maintenance or unexpected breakdowns. This ensures more realistic and reliable results. Logistic optimization is based on comparison of different scenarios. For a new scenario, equipment and practices, etc. can easily be modified, added or removed. At the same time the SPM produces all relevant data for every new scenario, which can be presented conveniently. This makes the SPM the ultimate tool to find bottlenecks or optimize plant logistics. The SPM is validated for several plants world-wide, with different characteristics and layouts. The SPM not only realistically simulates existing plants with all utilizations, crane movements and waiting times, but also to accurately predicts the influence of plant modifications or unexpected events like breakdowns. Given the flexibility of the SPM, any (new) steel plant can be simulated quickly when a layout and the requested data are provided.

Aug 16, 2017

By J. Kempken

Driven by customers, especially from the automotive sector, the supply of 100% prime quality has become essential. Furthermore the implication of quality costs and the yield of first class products define the steel companies' profitability and overall success significantly. The SMS group together with its subsidiary MET/Con has developed a comprehensive solution to assess the product quality over the production and processing chain. Process and production parameters originating from various data sources of the process automation are examined on their impact of quality related characteristics.Expert know how and comprehensive operational experience is translated into a quality guideline and a regulation framework as the sensitive core of the PQA solution.Once implemented, the system identifies immediately steel grade specific, deviations from ideal standard and proposes corrective actions including a final evaluation for each product at each processing step.The X-Pact® PQA (Product Quality Assessment) system is a substantial tool for root cause quality analysis and provides the required support to the production team. It will become an integral part of the corporate quality management system.

Aug 17, 2017

By Susanne Hahn

The Siemens VAI software model DynaPhase calculates thermodynamic properties depending on the chemical analysis of steel. It can be used online together with Siemens VAI’s secondary cooling model SIMETAL Dynacs 3D which is a unique feature. Offline it can be used to investigate the thermodynamic properties of steel grades and therefore supports the development of new grades. The core of DynaPhase is a substitutional solution model for the Gibbs free energy to calculate multi-component phase diagrams. The parameters of this model are determined by employing the CALPHAD approach. This model is combined with a microsegregation model to account for the interdendritic solidification process. New DSC (differential scanning calometry) measurements of the department of metallurgy of the Mining University of Leoben have been used to improve the DynaPhase database for high Al or Si concentrations. By comparing this experimental data to calculations it has been found that some of the widely used commercial software tools do not describe the ternary system FeAlC for high aluminum concentration correctly. In this paper we will show how thermal properties of high Al grades change with the optimized database and what impact this has on the secondary cooling of continuous casting, e.g. how the solidus point shifts on the strand. Moreover we will show that the online use of DynaPhase has many advantages for the production. Since DynaPhase uses the actual chemical analysis of the steel grade and not just concentration ranges or averaged concentrations it is possible to optimize the cooling strategy during casting for the actual chemical analysis of the actual heat.

Jul 30, 2018