Search Documents

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Satish V. Kailas

For product sustainability “closing the cycle” is the first requirement. If the materials used in making the product is not replenished at the rate at which it is being extracted, the cycle is open and the product would not be sustainable. This includes the materials used in generating the energy used to make the product, the transportation, use and disposal. If the materials used in a product, that includes lubricants, is one that cannot be replenished, it has to be recycled for the product to be sustainable. The other basic condition for sustainability is the eco-friendliness of the product. It is argued that the present lubricants do not fall in this category. Using the example of cutting oil emulsions we have shown that it is possible to meet the conditions of sustainability in terms of both the material extraction-replenishment cycle and eco-toxicity. Cutting oil emulsions made from coconut oil and natural additives are shown to have superior cutting properties and are completely eco-friendly. It is concluded that products made using these conditions are possible and is a necessity for man to lead a sustainable life. Closing the cycle, with respect to the energy used in the cycle will make the product completely eco-friendly.

Jul 31, 2018

By Raúl Daniel López

Ternium-Siderar steelmaking has been focused in permanent improvements and process optimization. At present the Slab Continuous Caster N°1 has been totally transformed after 20 years of uninterrupted work. The authors of this paper summarize and comment on aspects which were the main changes and place emphasis largely on those technological developments in which they have been active during that period. Productivity and quality have been our goals during the last 20 years; it has led us to improve process and to achieve better control tools. In the development of this presentation, the authors will put special emphasis on the explanation of those works that were made following their own experiences through the technical personnel who belong to the staff of the company.

Jul 30, 2018

By Túlio Magno Fuzessy de Melo, Luciano Santos Marques, Vicente Tadeu Lopes Buono

The influence of the coiling temperature after hot strip rolling on the microstructure and on the tensile and hole expansion properties of a 800 MPa multiphase steel was investigated. For the temperatures between 150°C and 600°C the microstructure consisted of a ferritic matrix with a dispersion of fine martensite-austenite (MA) and regions of degenerated upper bainite. In all cases the ferrite presented a heterogeneous mixture of polygonal, quasi-polygonal and acicular grains. The yield and tensile strengths showed a tendency of decreasing with the increasing coiling temperature, probably because of the larger fraction of MA particles at lower temperatures and higher fraction of quasi-polygonal ferrite at higher temperatures. The elongation was not significantly affected by the variation of coiling temperature. The average hole expansion ratio showed a maximum of 80% for the material coiled at 400°C and fell below 50% only for the coiling temperature of 150°C, probably due to the larger hardness difference between the ferrite matrix and the MA particles.

Oct 1, 2019

By Rodrigo Fina Ferreira

This paper presents a mineral liberation study on two iron ore samples from the Quadrilátero Ferrífero, in Brazil: compact itabirite of low-grade metamorphism (CI) and friable itabirite of high-grade metamorphism (FI). The quartz liberation spectrum for both samples have been obtained through QEMSCAN analyses, carried out for several comminution degrees, to compare the liberation characteristics and to evaluate the evolution of the quartz’s liberation degree after fragmentation. The results have shown significant differences in liberation spectrum between the itabirite samples studied. The liberation process of FI was easier than of CI, due its high porosity and larger crystal size compared with CI, which has shown more complex mineral assemblages with low porosity and smaller crystals. The quartz liberation spectrum has shown that grinding at P95 of 0.210 mm for the FI sample, and of 0.045 mm for CI sample, should result in satisfactory liberation for subsequent concentration step.

Aug 1, 2018

By Bi Zongyue, ZhangYongqing, NiuTao, Guo Aimin

Over the past twenty years, significant advances have been made in the field of microalloying steels and associated applications, among which one of the most successful application cases is development and application of heavy-gauge X80 coil with high temperature processing HTP practice used for China's Second West-East pipeline, the longest X80 pipe in the world. During this process, HTP design concept has been sucessfully applied to develop 18.4mm X80 coil with demanding low-temperature fracture toughness requirements. In the meanwhile, China's metallurgical workers have further optimized HTP design concept with the aid of powerful rolling mill and coiling equipment, and made it possible to develop 21.4mm X80 coil used for Russia-China East line. In the paper, we would simply review the development history of high-strength pipeline steels, and then give more priority to the fundamental points for sucessful development of 18.4mm X80 coil and SSAW pipe, which paved the way for subsequent development of 21.4mm X80 coil and SSAW pipe. Finally, we would present the test results of mass production and burst tests, and dispel the suspicion that SSAW pipes made of X80 coil are more qualified to resist ductile fracture.

Oct 1, 2019

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By Giulio Rodrigues Altoé

The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. PALF extracted from pineapple leaves, presents some significant characteristic, but until now only few studies on PALF were performed. This work aims to make the analysis of the tensile strength of polyester composites reinforced with PALF. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. After fracture the specimens were analyzed by a SEM (scanning electron microscope).

Aug 16, 2017

By Li Shanqing, Xu Jianghua, Li Hongmei, Huang Peijie

Cold rolled high strength steel are playing a very important role in reducing automobile weight for energy saving and environment protection. In recent year, more and more high strength steel were manufacturing in steel company. But there are some problems in the cold rolling process for high strength steel products. Periodic thickness deviation especially in strip head or tail is an important one in these problems. In this paper, the reason of periodic thickness deviation was analysed and a new AGC algorithm called Property FFC for high strength steel in tandem cold rolling was developed. The application of this new algorithm shows that it can reduce the thickness deviation.

Oct 1, 2019

By Detlef Ehlert

Energy efficiency is coming to the center of attention in the metallurgical and rolling mill industry due to increasing energy costs, limited resources and political requirements. Also, a green image and energy efficient production is a clear competitive advantage. SMS Siemag, being familiar with automation and measurement equipment, provides an energy data management system which gives transparency over the energy consumptions. All energy relevant media including electricity, gas, water, compressed air and further more can be recorded. The system is manufacturer-independent and allows the use of already installed measuring technology with the possibility of subsequent extension. So potentials for improvement can be recognized and energy savings can be estimated and proven after the implementation of the measures. Being familiar with the processes in the metallurgical and rolling plants, the system by SMS Siemag allows the assignment of the energy data to the production and plant data. Only by this connection, the data can be reduced to key performance indicators allowing authoritative evaluation of energy efficiency. The results are clearly represented on dashboards and support the continuous improvement process. The system also supports the energy controlling with an automatic reporting system, cost center assignment and in support with certification according to ISO 50001.

Jul 30, 2018

By Tiago Seixas Bittencourt

Technological developments, associated with the constant worry about the environmental impacts arising from industrial activity, it has driven the development of technologies and practices for efficient fumes and particulates capture arising from the manufacturing processes of steel in steel plants in general. Currently, the electric steelshops in operation with Electric Arc Furnaces (EAF), seek parameterize/design dedusting systems able to retain most of the particulates generated during melting and refining of steel in FEA through configurations of equipment, technologies and parameters operation in order to equalize the antagonistic relationship between effective fumes capture and energy balance of the EAF. The present work gets as a fundamental premise to evaluate critically the possible different settings of the usual dust removal systems, as well as their respective classical parameterizations. The work main purpose is to establish a general rule evaluation technique for dedusting system considering the different modes of operation of an Electric Arc Furnace.

Jul 30, 2018

By Andreas Cestonaro

Roll grade evolution in plate mill applications is traditionally following the development in hot strip mills. New grades normally find their way into service only after being successfully implemented in hot strip production. The majority of the plate mills worldwide are using work roll grades that have been invented before the 1980’s. But today the demands in the mills are pushed by sophisticated product mixes and longer rolling campaigns. The result of this development is a higher wear rate on the work rolls and as a consequence roll hardness is increased and advanced roll materials are used. The backup rolls are also affected by this. The wear rate is higher and the mechanical impact in terms of contact pressure and work hardening is increasing. This paper outlines the results of the roll grade development at Gontermann-Peipers and introduces new materials for work and backup rolls for plate mills.

Jul 30, 2018

By Mario SINNAEVE, Olivier LEMAIRE, Gisèle WALMAG, Sébastien FLAMENT

Many hot rolling mills worldwide face nowadays bonding zone fatigue problems before reaching scrap diameter of the work rolls. This phenomenon is nowadays known to occur in reversing roughing mills both in stainless steel and in carbon steel rolling. The phenomenon can be explained through longer rolling campaigns, inadequate backup or work roll maintenance, harder steel grades or increased throughput by reduced amount of passes to achieve the same thickness. In order to help users in optimizing the roll use, we developed a numerical tool to evaluate and optimize roll maintenance. This paper will review the influence of roll geometries on stresses generated at the roll surface but also at the bonding zone. We will also show how roll geometries can decrease contact fatigue damages by modifying crowning and chamfering procedures, shell thickness, material design or campaign length

Oct 1, 2019

By Alessandro Molinari

In recent times, coke oven machines are acquiring a more prominent role in the coke making process. Apart from the traditional handling of the coal and coke flow, nowadays these machines are also deeply involved in all environmental and process control aspects. Paul Wurth coke oven machines have been developed by Schalke to meet the most recent requirements in terms of emissions control, automation, instrumentation, operability and maintainability. In CSP, Ceará, the new coke making plant represents the status of the art of the technologies applied to the whole coking process; starting from the Coke Oven Batteries and the Gas Treatment Plant developed by Paul Wurth up to the Coke Machines supplied by Schalker Eisenhütte, whose technology is now part of Paul Wurth coke making products portfolio. Present paper describes the plant configuration focusing on Coke Oven Machines and the key factors which are guarantying the success of the project.

Aug 16, 2017

By Karl Berger

As the hot rolling of steel moves into new more compact and effective processes, and as steel producers look for new ways to reduce their costs and increase their margins in ever tightening markets and tolerances, the evolution in Steckel mill technology, layouts, and new innovations may well keep the Steckel mill as a viable option, especially in areas of the world where minimized capital investments are required. In this paper we examine the evolution of the Steckel mills over the last two decades, with emphasis on new innovations and practical results, and provide a summary of hands on experience with some of these innovations. Also a focus on the South American Installations is given (from Siderperu to Gerdau’s newest Combination- Plate-Steckel-Mill). In addition, we aim to show the viability of the Steckel mill as an option for many existing or prospective steel producers, as the quality of the products rolled with Steckel mills reaches new quality parameters and as new innovations permit the rolling of thinner and wider materials, reaching new applications and wider share in markets, while maintaining a strong foothold in the traditional uses of Steckel mill products such as stainless steel, structural, and line pipe materials. As the ability to handle heavier, thicker, and wider coiled plate products increases, the coiled plate Steckel mills option is as strong an option as ever.

Aug 17, 2017

By J. N. Stevens, M. Tulwin, P. J. Lawlor

All metals producers are on an unending search for a competitive advantage. They need to produce in the most cost effective way. Sometimes a new mill might be considered but in this paper we present examples of how this might not always be necessary. A detailed investigation by an equipment vendor who can consider the mill and or plant as a complete entity: mechanics, automation and process control can often find solutions that are both lower cost and can be implemented in shorter time frames.

Oct 1, 2019

By Konrad Krimpelstätter

The need for more effective and flexible roll-gap lubrication technologies in hot and cold rolling mills is steadily increasing due to ever-greater requirements placed on the rolling process and the final products. In particular, the rolling of high-strength steels poses enormous demands for both the rolling mill and the coolant/lubricant to be used. The presented paper focuses on two innovative technologies for highly efficient roll-gap lubrication for hot and cold rolling, which were developed utilizing extensive knowledge and expertise about the tribological interactions in the roll-gap. The advanced work-roll lubrication package (A-WRL) for hot rolling and ESP mills is using specially designed mixer-nozzle units to mix the water/oil emulsion very close to the nozzles to minimize the risk for contamination and clogging. The nozzles are quickly exchangeable and are optimized to ensure uniform lubricant distribution, high plateout efficiency and minimum oil consumption. This eco-friendly solution does not require any chemical additives or cleaning agents and significantly reduces electrical energy consumption and work-roll wear. The roll cooling system on mill entry and exit side remains switched-on, which is of vital importance especially for highperformance hot strip mills. Minimum Quantity Lubrication MQL® represents a new generation of roll-gap lubrication technologies for cold rolling, which applies minimum amounts of pure rolling oil finely atomized with pressurized air directly onto the work roll surface. This allows controlling the oil film thickness depending on actual process and product parameters, providing increased lubrication flexibility, significant improvement of strip surface cleanliness through reduction of strip wear. MQL® was successfully installed and tested on two industrial tandem cold rolling mills in Europe. Advanced WRL and MQL® represent Primetals’ latest technologies that feature a robust and reliable system comprising standardized interfaces and flexible communication options. Both packages can easily be integrated into existing or new hot strip mills, ESP lines or cold mills.

Aug 17, 2017

By Álvaro Lúcio

This paper outlines the DPC process as na economic and environment friendly option for the use of cultivated forest as a source of raw material for metallurgical charcoal.The DPC process was specially developed to bring logistic, environmental, technical, economic and global energy efficiency when compared to termal1 the existing biomass carbonization process. The DPC process utilizes the volatile materials (condensable and non condensable) as a source of the energy required by the carbonization process guarantying its complete combustion. As result the DPC process avoids the burning of termal1 the loaded wood, obtaining a higher charcoal to biomass yield, and avoids the emission to the atmosphere of polluting gases. Gases emitted by the carbonizing wood have na energy termal1e enough to dry the wood soon after its harvesting. By avoiding the storage in the field during na average of 150 days, the resulting economy is quite significant. As a termal1e1 the higher charcoal to biomass yield na termal1e1e economy is obtained through the reduction of the cultivated forest term. This paper emphasizes the economic advantages of the DPC process.

Aug 16, 2017

By Lesli Peterson

Spraying Systems Co® has continued to develop and evolve descale nozzles through the years. The most recent addition to the descale nozzle line, the DescaleJet® Pro, provides more impact and a more uniform distribution than previous descale nozzles. The improved performance has been achieved through multiple design changes such as a smoother approach, updated vane design and improved carbide orifice. In addition to providing improved spray performance the nozzle also lasts longer than previous versions. The new technology has been thoroughly tested in the lab using impact measurements and accelerated wear testing. In addition to lab testing the nozzle has provided improved performance and longer wear life for those that have made the change to the new technology. The new nozzle technology and the benefits to the rolling mill will be discussed.

Jul 30, 2018

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019