Search Documents

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By AIME AIME

MINERAL production of the United States is valued at over five billion dollars a year at present and the industry employs close to a million workmen, yet such maps as are available that might indicate the geographical distribution of this industry show only the location of coal and oil fields and of other mineral deposits. No recent map is available that shows this distribution in a quantitative way. The purpose of the maps and graphs here presented is twofold: (1) to give the mining engineer a clear conception of the relative value and the pattern of distribution of minerals in the United States; (2) to test the so-called block-pile (or grouped pillar) system of statistical mapping, which makes this presentation possible. (I discussed this method of mapping in an article which appeared in Economic Geology in 1939, Vol. 15, p. 185-188.)

Jan 1, 1941

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922

By Ellis Clark

Within the last ten years the progressive party of China, headed by Li Hung Chang, the Viceroy of Chi-Li, has been making great efforts to develop the mining resources of that country, and particularly those that are within reasonable distances of the sea-board. Attention was first paid to the coal-deposits, especially those at KaiPing, which have been placed on a profitable basis with an output of 1500 tons per day, under the energetic management of Mr. Claude Kinder, M.I.C.E., and the successful financiering of Tong King Sing. These coal-mines were described in a report by Kwong Yung Kwang, edited as a paper for the Institute (Duns., xvi., 95.) The attention of the leaders of the progressive party has for the past five years been turned also toward the development of the precious and related metals—gold, silver, copper and lead. De-

Jan 1, 1891

NEW MEMBERS The following list comprises the names of those persons who became .members during the period of Jan. 10, 1918, to Feb. 10, 1918. ANTISELL, TONER, Min. Engr.; Supt., Great Falls Mine of Maryland, Chevy Chase, R: F. D. No. 4, Washington, D. C. BAKER, RAYMOND FRANK, Geol:, The Texas Co., Producing Dept., Box 362, Tulsa, Okla. BERTON, ADRIEN, Chief Engr., Corocoro United Copper Mines, Ltd., Corocoro, Bolivia. Buck, WILMER EARLE, Met., Curtis & Co. Mfg. Co., Hamberger & Kienlein Aves., St. Louis, Mo. BUELL, WILLIAM H., Asst. Director, Experimental Station, E. I. duPont de Nemours & Co., Wilmington, Del. CARDENAS, FEDERICO F., Mgr., Cia. Minera Nazareno y Alicante, S. A., Allende, No. 112, Saltillo, Coah., Mexico. CHEVALIER, JEROME A., Pet. Geol., The Carter Oil Co.; Exchange National Bank Bldg., Tulsa, Okla. CLEAVES, DANIEL LUNT Supt., St. Joseph Lead Co., Herculaneum, Mo. CLOTHIER, GEORGE A., Resident Min. Engr., Province of British Columbia,

Jan 3, 1918

By S. J. McCarroll

THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.1 During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO, process was constructed. Numerous operation difficulties ensued, and the plant was closed when the manganese situation in the country eased.

Jan 3, 1954

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit and a number of surveying technicians, has proven to be a very expensive and time-consuming operation. Now, however, engineers have adapted the laser to help ease the problems of surveying, at the same time increasing the efficiency of such operations. The laser, which projects a continuous, narrow red beam of brilliant light, provides a constant alignment reference that does not interfere with personnel or equipment. A complete laser alignment system, specifically designed for and suited to a variety of mining and tunneling operations, has been developed by the Perkin-Elmer Corp. The engineering significance of this development can be fully realized when it is noted that, aside from potentially tremendous economic advantages in terms of labor savings, the laser beam provides a system of alignment that is at least ten times more accurate than presently used optical systems. The new laser system provides accuracies within 10 microinches per foot (1 x 10-5in.) when used with an accessory centering detector. In one of its first field trials, the laser was used for alignment of a two-mile tunnel which showed a total deviation of less than 5/8 in.

Jan 4, 1968

By Waldemar Lindgren

CONTENTS. [ ] I. INTRODUCTION. THE precious metals, gold and silver, are the basis of the monetary systems of the world. It is, therefore, natural and inevitable that widespread interest should be manifested in their production and in the various classes of deposits in which they are contained. At times a great scarcity of the precious metals has prevailed; at other times the production has seemed so abnormally large that fears have been entertained regarding their ultimate retention as standards of value. Since most nations have adopted the gold standard, and the remaining ones appear likely to do the same in the near future, the question of available supply of gold for the present and future very naturally arises. This necessarily involves a consideration of the characteristics of the gold-deposits. After the absorption of the gold treasures of the New World by the conquistadores, the gold-placers of Brazil and Russia

Jan 1, 1913

By H. Rumfelt

Strip mining in the domestic coal industry is contributing a greater proportion bf overall production than at any time in the past. U.S. Bureau of Mines statistics show that the percentage of total production mined in 1958 by stripping methods increased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically. Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely).

Jan 5, 1961

By H. E. Sadler, Prof. Silliman

The research here recorded was undertaken early in the present year, and has been prosecuted steadily for about eight months. While the work has been under my constant supervision and advice, the labor has all been performed by Mr. Sadler, to whom is chiefly due the development of the successive steps which have led to the final result. The process is better than I dared to hope, and we are able to place at the command of chemists and engineers interested in the matter an apparatus of continuous and uninterrupted action, and methods of analysis by which the daily averages of the two variable and inconstant factors of illuminating gas, ammonia and sulphur, may be determined with all needful accuracy, even by those little skilled in chemical manipulation, and with very little loss of time. This research has been carried out in the laboratory of the New Haven Gaslight Company.

By Leon Dominian

I. INTRODUCTION APART from local needs in the country's development, the interest attached to Turkish fuels grows chiefly out of the importance of the railway industry in Asiatic Turkey. Geographical conditions make of the tracks in this region the most essential link in a chain of world-girdling lines. By its position Asia Minor can be likened to a bridge in the through routes destined to connect European factories with Asiatic and African markets. An uninterrupted right-of-way from points in central Europe to populous Indian cities must necessarily pass through the valleys A Anatolia. Crossing thence the Taurus Mountains its natural passage is indicated as the Mesopotamian lowland and the shores of the Indian Ocean. Similarly land connection between Europe and Africa can be obtained only by passage through Asia Minor, Syria and Palestine. The occurrence of fuel within an area of such significance from the

Jan 6, 1916

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes . The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper' described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely. First, curves have been calculated for dipping discontinuities. Stern' and Aldredge hose a few widely separated dip angles. Trudu confined his attention to small dips. Berel'kovskiy and Zubanov computed gradient curves for widely separated dip angles. Unz as given the most complete solution, with a brief attempt to treat the three-layer case. Second, anisotropy can be taken into account. It seems geologically probable that layered materials have different vertical and horizontal conductivities. Cagniard, Maillet, and Pirson et up methods for finding an equivalent hypothetical isotropic medium. Standard interpretation methods can be applied to this, and the actual medium can then be deduced. Belluigi'" discounts the practical importance of anisotropy; Geneslay and Rouget do not agree with his conclusion. Third, the effect of variable resistivity in a layer can be considered. Keck and Colby" examine the mathematics of an exponential increase in a surface layer. Several authors, for example, Stevenson,'' consider a continuous variation of resistivity with depth. The present paper deals with a linear variation of resistivity in a surface layer. Geologically, surface variations should be expected. Unconsolidated materials such as glacial drift show marked irregularities over short distances. The effects of weathering change with depth. The moisture content of material above the water table may vary from a dry sand to a saturated clay, and both of these will be changed by rainfall. Figs. 1 to 6 present apparent resistivity curves to show the effect of a variable surface layer. In all cases resistivity varies linearly with depth down to a depth of one unit. Material beneath this depth has constant resistivity. Electrode separation is plotted in depth units. Insets on each figure show the corresponding cross-sections, plotting true resistivity against depth. To illustrate, consider curve A of Fig. 1. The true resistivity of material at the surface of the earth is taken as 0.4 units. Resistivity increases with depth, reaching a value of 1.0 at 0.5 depth units and 1.6 at 1.0 depth units. Below a depth of 1.0, all the material has very low resistivity (zero, for purposes of calculation). Curve A in the main part of Fig. 1 shows how apparent resistivity varies for this case as the electrode spacing is increased. To illustrate further, curve E of Fig. 4 corresponds to true resistivity of 1.2 units at the surface, 1.0 at a depth of 0.5 units, 0.8 at a depth of 1.0, and 1.5 for all depths greater than 1.0. Apparent resistivity curves have been plotted logarithmically so that the shape of the curves becomes independent of the units, giving the curves wide validity. A certain drift-covered area, for example, shows a gradual decrease of resistivity from 230 ohm-meters at the surface to 150 ohm-meters at the bedrock surface, 275 ft down; bedrock resistivity is 800 ohm-meters. Curve E of Fig. 5 indicates that true resistivity decreases from 1.2 units at the surface to 0.8 at a depth of 1.0, then increases abruptly to a constant value of 4.0 units. Since resistivity and depth ratios are the same, this can be used to predict the field curve. For Fig. 5, multiply true resistivity and apparent resistivity by

Jan 1, 1955

By Seishiro Hirakawa, Hiroshi Tokunaga, Hironori Nakamura

Two unique processes of reclaiming zinc from various secondary materials were developed and have successfully been operated for years by Mitsui Mining and Smelting Co. These processes were established based on the characteristic and local energy conditions; i.e., (1) at Miike Smelter, located above the largest coal deposit in Japan, a combination of slag fuming and semi-blast furnace (MF)processes takes advantage of using coal and the carbon bearing briquette residue from the vertical retort plant as reducing agents, (2) on the other hand, at Kamioka Smelter, a direct reduction of zinc-bearing lead slag by using electric furnaces is of advantage in view of cheap electric power supply from our own hydraulic power plants. The former also consumes lots of zinc bearing fines and drosses from various steel plants, fabricators and secondary zinc smelters, while the latter, zinc leach residue from its own electrolytic plant

Jan 1, 1976

By Eckley B. Coxe

(WITH FIGURES ON PLATES II, III, AND IV.) I DESIRE to call the attention of the Institute to two deep vertical shafts, which are now being sunk in Schuylkill County, Pennsyl¬vania, about 1 1/2 miles north of Pottsville. These shafts are of interest to the mining engineer, not only on account of the novelty of the method of sinking adopted, which promises to produce a revolution in that branch of mining engineering, but also as examples of the manner in which such work should be undertaken. GEOLOGICAL SKETCH OF THE TERRITORY TO BE WORKED BY THE SHAFTS AND REASON FOR SINKING THEM. The Mammoth or E Vein of the anthracite coal-measures in that part of the Schuylkill region near and north of the town of Pottsville lies at a great depth below the surface, and has, in consequence, never been worked in that locality.

Jan 1, 1873

By Bunting S. Crocker

Pebble grinding was used at Lake Shore Mines in 1949. A full description of experimental evidence and test plant results was published in 1952 1 and further operating details in 1954.2 In more recent years the term autogenous grinding has been coined and is now frequently seen in the technical literature. Autogenous crushing and/or grinding covers any grinding mill in which the larger of ore are made to grind the fine pieces; the crushing and grinding may be either dry or wet. This discussion deals only with wet autogenous grinding, and only in the fine grinding part of the circuit, i.e., from 6 mesh to 92 pct -325 mesh. The term pebble milling could apply to fine autogenous grinding in which the pebbles are made from the ore itself, or it could also refer to grinding with pebbles, such as flint pebbles, from a source outside the mine.

Jan 5, 1959

By Guy R. Johnson

It is a common observation among those engaged in the ironbusiness, that the lower (i.e., the less graphitic) grades of pigiron show a rough face on the pig. As such irons are always low in silicon, the generally accepted belief is, that this rough face is due to the absence of silicon. Certain investigations, however, made by the writer on Embreville pig-iron, and extending over nearly a year's time, seem to indicate another cause, namely, the giving-off of included gases, particularly sulphurous oxide (SO2,). It is, of course, the tendency of such gases to rise through the iron, escaping into the air; and the more liquid the iron, and the longer it remains liquid, the greater the chance for such escape. The lower grades of iron, being always colder, tend to solidify early, and before the included gases can completely escape.

Jan 1, 1898

By James E. Lawver

A SURVEY of Minerals Beneficiation Div. membership indicated genuine interest in automatic process control, but revealed that the average mill is operating with a minimum of self-regulating devices. Apparently, the mill operators are content to continue without controls until the practicality of self-regulating devices is more generally accepted, or, in the opinion of the writer, until automatic controls become a necessity to meet economic demands of product quality and cost. Both to stimulate interest in control, and to solicit publication of technical know-how by members and equipment manufacturers, this paper presents a cross section of control problems in two general categories: (a) Control problems that can usually be solved by reference to the literature, i.e. controls that have proven successful in the mineral or chemical industries; (b) Problems that are troublesome and frequently unsolved due to unavoidable adverse conditions in the mill circuit to be controlled.

Jan 10, 1953

By A. U. Seybolt, V. A. Phillips

Binary iron alloys containing 1 pct of Al, Cr, Mn, Mo, Si, Ti, or V, and 0.4 pct C, 1 pct Cr steels with and without 1.2 pct A1 or 2.0 pct Ti additions, were ion-nilrided at 550° to 600° in N-H mixtures. Nitriding increased the inicrohardne ss of all the binary alloys except those containing manganese or molybdenutn, and also hardened the heat-treated steels if aluminum or titanium urns present. Transmission electron microscopy revealed particle formation in all casts where hardening occurred. Electron diffraction gare positive identifications for ALN, CrN, and a, Si3N4 in the binary alloys, and AlN and CrN in the aluminum- cold chromium-bearing steels, respectil&apos;uly. Cubic VN with a, = 4.13A was tentatively identified. Particles, apparently of CrN, also formed in the base steel but did not increase the hardness very much. Chromium and vanadium formed nitride platelets on {001}° matrix planes, while titanium gave clusters <15A diam. Aluminum nitride precipitated at grain and subgrain boundaries, and within the grains. Silicon gave profuse precipitates of several Morphologies at grain boundaries and cubical particles within the grains. No effect of the alloy carbides on nitride precipitation was observed in the heat-treated steels. THE nitriding of steel has been a well-established commercial process for about 40 years, but in spite of this comparatively long period of use there have been few studies aimed at understanding the process. Most studies, like the early but very competent work of Jones and organ&apos; and nones.&apos; were concerned with establishing the pertinent engineering variables of steel composition, gas composition, temperature, and time. As far as the present authors are aware, there have been no studies of the composition, size, shape, or distribution of the nitrides formed in the nitriding of steel. Noren and Kindbom3 did, however, examine a few nitrided steels by surface replica electron microscopy, and were able to show the presence of car-bonitrides and AlN and TiN nitrides. pitsch4,5 and Hrivnak6 examined nitrided pure iron by transmission electron microscopy. Baird7 found manganese nitrides in Fe-1.6 pct Mn when nitrided at 650°C, using the same technique. In the present work, emphasis was placed on transmission electron microscopy because of its inherently better resolution, using principally binary alloys of iron containing 1 pct of alloying element. In addition, a few simple 0.4 pct C steel compositions were examined to investigate possible carbonitride formation. It was not anticipated that all of the added elements would form nitrides under the conditions used, but it was considered desirable to obtain direct experimental evidence on this point. It would be considerably easier to ascertain the presence of alloy nitrides by examining appropriate binary alloys in preference to relatively complex steels. The work reported here could have been done using orthodox ammonia-nitriding procedures, but an operating ion-nitriding equipment was available, and was therefore used for specimen preparation. EXPERIMENTAL DETAILS 1) Materials. Binary alloys were made up from vacuum-melted electrolytic iron with 1 wt pct additions of Cr, Ti, V, Al, Mn, Mo, and Si of about 99.9 pct purity. In addition, three steels were similarly made up—a basis steel with 1 wt pct Cr and 0.4 wt pct C and two steels with further additions of 1.2 wt pct A1 or 2.0 wt pct Ti, respectively. The materials were vacuum-melted and cast as 11-lb heats into tapered square molds of about 2 by 2 in. average cross section. The castings were forged and hot-rolled to 11/4 in. rounds. Discs of 4 in. thickness by about 1 in. diam were machined from the rods. Some of these discs were hot-forged and hot-rolled to about 0.020 in. thick, sand-blasted, and then cold-rolled to about 0.003 in. thick. At this point, the surface was cleaned by light etching with HC1, then washed, dried, and vapor-degreased prior to nitriding. 2) Ion-Nitriding Procedure. The type of ion-nitriding equipment used here is similar to that described by Jones and Martin.8 Briefly, a mixture of nitrogen and hydrogen at 5 mm total pressure is placed in a vacuum chamber with a dc potential of 450 to 500 v applied between the work (cathode) and the grounded metal vacuum enclosure (anode). Nitrogen ions are accelerated to the work where a thin layer of Fe4N forms on the surface and thus sets up a nitrogen concentration gradient. This causes nitrogen atoms to diffuse into the surface layers of the alloy forming a finely divided dispersion of alloy nitrides, causing hardening of the surface. In the work to be reported here. the nitriding was carried out at 550° to 600°C to be consistent with commercial nitriding practice. The temperatures cited are those measured by a thermocouple located under a platform on which the work was sitting. Except where otherwise stated, the mixture used in nitriding the binary alloys contained -2.0 pct N, balance hydrogen. The nitrogen concentration in the nitriding gas mixture used for the binary alloys was purposely kept lower than normally used in nitriding steels. 10 to 20 pct, in order to minimize Fe4N formation. In this way only the alloy nitrides would be present as a second phase. However, in the case of steels which would contain a- carbide phase along with as

Jan 1, 1969

By R. L. Wiegel

The two questions considered in this study are: (1) what similarity is there in the liberation of magnetite from various iron formations, and (2) how is this liberation affected by the size reduction technique employed. Twelve sample suites were obtained from commercial concentrators processing magnetite iron formation in the United States, Canada, and Australia. These samples have grades in the range 15 to 45% magnetite iron and approximate mineral grain sizes o f 50 to 2000 microns. Efforts were directed at measuring the liberation characteristics of the samples obtained from the concentrators primary grinding mills. The Davis tube, a laboratory magnetic separator, was used to concentrate individual size fractions of the size reduction product to determine liberation data. These liberation data were compared with relationships calculated from a highly idealized mathematical model of liberation in a binary mineral system. The results of these comparisons have been encouraging for nine or ten of the twelve samples tested. This leads to the conclusion that for most commercial iron formations, at least with conventional rod mill size reduction, it is possible to quantitatively characterize liberation with two parameters: an effective mineral grain size and ore grade. Limited laboratory size reduction tests as well as one of two sets of liberation data from commercial primary autogenous grinding lend some support to the contention that autogenous grinding can affect mineral liberation.

Jan 1, 1976

By G. K. Burgess

THE question of the allotropy of iron, in spite of a vast amount of experimental work and perhaps an even greater amount of theorizing, is not yet settled. That there is a definite transformation in iron near 900,° the A3 point, is generally recognized, as well as the fact that the temperature of this transformation is lowered by the addition of carbon and metallic elements. On heating, the transformation Ac3 is always found at a higher temperature than the transformation on cooling, Ar3. Whether the A3 transformation is sharp like the melting point of a pure substance, or extends over a considerable range of temperatures, embracing perhaps as a lower limit the A2 change, appears to be still an open question for pure iron. The nature and identity of the A2 transformation, it would appear from recent publications, has not yet been satisfactorily settled. In the present paper a critical, historical summary is given of the experimental investigations of the location of A2 and A.3 in pure iron, together with brief mention of some of the theoretical aspects of the subject, and an account is given of a series ?of experiments carried out with several samples of very pure iron which were studied by two methods of thermal analysis in the range from 5000 C. to 1,000° C., and which it is believed furnish a contribution of considerable interest as to the location and nature of the A3 and A2 transformations. Great attention has been given to the details of experimental manipulation and to the preparation of the samples, as it was soon found that some of the discrepancies noted in the work of many experimenters may be traced largely to lack of precautions which we have found essential. For example, to anticipate somewhat, it is necessary to provide a suitable practically gas-free furnace, the heating and cooling of which may be regulated to a nicety. To render a minimum the deforming effects on the cooling and heating curves of the poor conduction of the sample, it must be of a form and mass to pass on its heat rapidly and completely to the thermocouple; and finally the sample itself must be freed from gases which, if present, further mask the definiteness of the heating and cooling curves. We, have also varied within wide limits the several factors which may influence the determination of the exact location and shape of the transformation ranges, especially the mass and preparation of sample, rate of heating and cooling, design of furnace; and finally, as nearly as it is experimentally possible, we have worked with a substance approaching pure iron, free from occluded gases and other impurities, and contained within a vacuum.

Jan 10, 1913