Search Documents

By O. D. Gonzalez, H. A. Wriedt

Alloys ranging from pure iron to pure nickel were saturated with nitrogen gas at 918°, 999°, and 1217°C and analyzed. The solubility of nitrogen at 1-atm pressure was obtained as a function of nickel content for the whole range of iron-nickel alloys and the temperature dependence of solubility is shown for the experimental alloy compositions. The heat of solution and the entropy of solution of nitrogen in the alloys as func-tiom of composition up to 41 pct Ni are given. 1 HE acquisition of more exact thermodynamic information for systems composed of iron with various alloying elements continues to interest ferrous metallurgists. The interstitial alloying elements, especially carbon, hydrogen, and nitrogen, comprise a field of particularly intense study. A recent investigation of carbon solubility in Fe-Ni alloys held at 1000°C in gases of fixed carbon activity showed an unpredicted minimum in the solubility near 72 pct Ni.1 The present investigation was undertaken to see if a similar anomaly in solubility existed for nitrogen in Fe-Ni alloys. The solubility of nitrogen in ? iron at known nitrogen activities has been measured several times.&apos;-&apos; Corresponding information for the solubility of nitrogen in solid Ni and Fe-Ni alloys is not available. Juza and sachsze9 reported that metallic nickel dissolved 0.07 pct N in equilibrium with Ni3N at 445°C. This result was regarded as dubious by Turkdogan and Ignatowicz10 who found less than 0.0004 pct N in nickel specimens equilibrated at 600°C with ammonia-hydrogen mixtures having fugacities of N2 gas up to 35,000 atm. Such fragmentary reports indicate only that nitrogen gas has a very much lower solubility in nickel than in iron. MATERIALS A purified iron from Battelle Memorial Institute was used for solubility measurements. This grade contained more than 99.95 pct Fe, the highest content of any measured individual impurity being 50 ppm for each of As, C, Cu, and Pb. The nickel and iron-nickel alloys, supplied by the International Nickel Co., contained 0.02 to 0.04 pct C, 0.17 to 0.19 pct Mn, 0.04 to 0.08 pct Si, < 0.01 pct P, <0.03 pct S, and <0.20 pct Co as principal impurities. The Fe-0.59 pct Mn alloy was of zone-melted quality, the highest concentration of any individual impurity being 15 ppm Al. The "prepurified" grade of nitrogen gas from Matheson Co. had a nominal nitrogen content of 99.996 pct. An "electrolytic" grade of hydrogen gas from National Cylinder Gas. CO. in which the principal impurity is water vapor was admixed with the nitrogen to prevent oxidation of these specimens. This grade was preferred to a purer grade because the presence of some oxygen helps in suppressing contamination of the specimens, for instance, by silicon from the porcelain furnace tube. EXPERIMENTAL PROCEDURE The specimens were equilibrated in vertical tube furnaces through which a 99 pct N2-1 pct H2 gas was passed at ambient pressure. For the 915", 918", and 999°C runs, a wound-resistance furnace was used, and for the 1217°C runs, a furnace with a tubular silicon carbide element was used. The temperature control system on both furnaces was similar: a Weston "Celectray" controller with a modulator, responding to the electromotive force of a thermocouple with its hot junction in the furnace, switched the furnace current between high and low settings. The temperature distributions in the working zones of the furnaces were determined with calibrated Pt/Pt-10 pct Rh thermocouples. The overall uncertainty in temperature was estimated to be ±3° at 915° to 999°C and ±5° at 1217°C . Consideration of the small temperature coefficients of the equilibria studied, together with the error limits in the method of analyzing for nitrogen, showed that further refinement in temperature uniformity would give no improvement in resultant accuracy. The reactive gas was generated by mixing together "prepurified" nitrogen and "electrolytic" hydrogen directly from cylinders commercially supplied. The flow rates of nitrogen and of hydrogen were fixed by setting with bleeders the pressure drops across the individual calibrated flow meters of constant resistance. For any given alloy, the solubility of nitrogen at 1-atm pressure (% N) was obtained from the analyzed nitrogen content of equilibrated specimens (% Na)according to Sieverts&apos; law, thus

Jan 1, 1962

By Carl A. Zapffe, George A. Moore

IN a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal sub- structures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the "disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, un- affected by chemical attack and undistorted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. MATERIALS STUDIED In commercial steels, defects caused by hydrogen take various external forms ac- cording to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement-"pickling brittleness"-in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free- machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This , choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group I: Prepared from Armco Ingot Iron As shown in Table I, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

By W. M. Myers

Certain minerals possess inherent color and other properties that make them suitable for the pigmentation of paints, mortar, plaster, concrete, face brick, and other materials. Their production is one of the most ancient of mineral industries and their use by primitive man is well known. These natural pigments have some economic factors in their favor, particularly wide geographic distribution, low cost of production, ease of preparation, chemical stability, and permanence in use so that they continue to form the basis of a small but useful industry. When used in paints such pigments act as a filler and supply body and opacity in addition to color. Natural mineral pigments are prepared for the market by the comparatively simple operations of washing, grinding, blending, and calcining. Any one, or all of these processes may be applied to a single pigment. The development of synthetic pigments and the use of byproduct materials have introduced competition with the products of nature and are having a growing influence on the economic position of the mined minerals. Development of the Industry The industry developed to commercial stature in Pennsylvania largely because of the presence of beds of ocher extending from Easton in a southwesterly direction toward Reading, and a variety of small iron mines in the region. The mining of paint ores in the Lehigh Valley was active as early as 1850 and shortly after the Civil War the establishment of mills expanded production and led to the development of new products and eventually the manufacture of synthetic pigments. Pennsylvania continues to maintain it.s leadership as a producer of mineral colors. Production is recorded also in New Jersey, Illinois, Virginia, Ohio, and Georgia. Iron as a Pigment Iron in various compounds is the most important pigment in nature. The iron pigments are characterized by stability, light fastness, good covering power, high index of refraction, and economy in production. Ferrous compounds display a typical green coloration. This has not been employed as a commercial pigment to any great extent except incidentally in such greenstones as have been used in construction, or crushed and sized for application as a granule to roofing. Ferric oxides are characteristically red and form an important group of industrial pignents. Hydrated ferric oxides exhibit various shades of yellow and are present in such familiar pigments as ocher and sienna. The addition of small amounts of manganese oxide or carbon as organic matter to the yellows produces the brown umbers. Magnetite is one of the few black minerals that grinds to a black powder. The mineral pigments vary from earth colors of low intensity and great dilution of iron content to almost pure iron compounds with high tinting strength and correspondingly greater value. There has been some relationship between the mining of iron ores and the production of mineral pigments; although the production of colors is not carried on appreciably as a byproduct of iron mining. A number of mineral pigment producers, particularly in the eastern states, have operated mines which in the past were small producers of hematite, bog ore, or carbonate ore. The knowledge of the location of the deposit and its possibilities as a producer of pigment are due to its past history as a producer of metallic ore. Many iron compounds may be changed in color by calcination, the end product being Fe2O3, a stable red oxide. The yellow hydrated oxides may be changed to red. The gray carbonate, found in Carbon County, Pa., calcines to a fine red product. Ferrous sulphate (copperas) often available in tonnage as a byproduct of the steel industry, breaks down under heat or chemical action leaving a residual red oxide. Pigments produced by calcination or dissassociation of compounds possess the advantage of fine particle size and ease of grinding. Mineral Pigments MINERAL BLACKS Many black minerals grind to a light colored powder. This characteristic is familiar to the mineralogist as the white streak produced by a black

Jan 1, 1950

By L. S. Allen, R. L. Caldwell, W. R. Mills

Borehole models used in the study of nuclear well logging are reviewed and the merit of heterogeneous us homogeneous formation simulation is discussed. .A heterogeneous model for simulating sandstone formations of variable porosity is described. Simulation adequacy was checked by steady-state and pulsed-neutron measurements. INTRODUCTION In the course of developing new methods of nuclear well logging, the problem of testing new logging instruments under controlled conditions always arises. This testing is usually done in wells of known lithology, porosity and fluid saturation, or in laboratory test facilities which simulate the borehole environment. Although the former approach is possibly more satisfying, it is frequently difficult or inconvenient to find wells with enough variation in the cited parameters for a truly comprehensive study, On the other hand. laboratow- test facilities can simulate a wide variety of formation and borehole conditions if care is exercised to maintain adequate simulation under all conditions. Workers concerned with the development of nuclear well logging methods have reported several types of research facilities in the past. Tittle, et a1 used cubical tanks filled with Ottawa silica sand to study the steady-state behavior of thermal and epithemal neutrons in simulated sandstone logging environments.1 In addition to the effects of fresh vs salt water, a wide variety of casing sizes and compositions were investigated. Tittman also used a large tank of Ottawa sand to measure the slowing down length of sio2;2 for making the same measurement in CaCO3, however, an assembly of solid Vermont marble blocks was used. More recently a very useful and carefully planned test pit for nuclear logs was constructed under the auspices of the API.3 This facility consists of three massive limestone sections, each 6-ft thick and more than 5 ft in diameter. The blocks are buried, one on top of the other, in a concrete- lined pit having a total depth of 24 ft. Each section is made of a different limestone to achieve porosity variation, the selection being Carthage (2 per cent), Indiana (19 per cent) and Austin (26 per cent). The blocks are traversed by a 7 7/8-in. diameter borehole and are saturated with fresh water. Great care was taken to insure total saturation of the stone. Homogeneous mixtures and materials have not been used exclusively for simulating earth formations. Tittle, et a1 4 showed that a heterogeneous lattice of water and graphite could be used to simulate Liquid furfural with very little effecton measured thermal and epi thermal neutron distributions. Subsequently, a lattice-type model for simulating limestone earth formations was designed and built by Berry This limestone model was constructed of 7/8- x 11/4- x 36411. marble rods glued together with a plastic resin to form a 36-x 42- x 42in. cube. The cube was honeycombed vertically with 7/8- x 7/8- x 3641-1. holes for porosity and had a 111/2-in. diameter hole in the center to serve as the borehole. Lower porosities were simulated by placing marble rods in the square holes. The finished cube was used with the borehole vertical and set in a tank to hold liquid for filling the holes in the rock matrix. A second type of heterogeneous borehole model has been proposed by Kukharenko, et a1.6= In this concept the model is composed entirely of solid material. The hydrogen equivalent of formation fluids is simulated by making the model of alternating layers of dense rock and celluloid. Additional hydrogen is included by drilling vertical holes in the rock sections and filling them with solid forms of hydrogeneous material. The volume of the holes is equal to the volume of the celluloid layers, so an axial and radial dispersion of the hydrogeneous material is thus obtained. One such model was composed of alternate 50 mm-thick sand layers and 2 mm-thick celluloid sheets. Approximately 200 appropriately spaced plastic tubes were used in each sand section. The plastic tubes were filled with paraffin for additional hydrogen concentration. This arrangement yielded a model with a water-equivalent hydrogen concentration of 10 per cent. Experimental data taken in this model and in a model consisting of the same material but homogeneously dispersed showed that the heterogeneous system adequately

Jan 1, 1966

By F. D. Rosi, F. C. Perkins, L. L. Seigle

An investigation was made of the mechanism of plastic flow in coarse grained specimens of both sponge and iodide titanium at low (-196°C) and high (500° and 800°C) temperatures. Deformation by slip occurs predominantly on a {1011} plane and in a <1120> direction over this entire temperature range, and secondary slip on {101-1} planes becomes more prevalent with overthisentireincreasing temperature.range, The crystallographic habit of the predominant twin planes becomes more prevalent with type is temperature-dependent, and deformation by twinning increases as the temperature of testing is lowered. Kink bands were not observed at -196OC and rarely at the high temperatures. A LTHOUGH the deform a tional mechanisms in . -titanium at atmospheric temperature have been extensively investigated," there is little information regarding the influence of testing temperature on these mechanisms. The only available data come from the recent work by McHargue and Hammond, who extended single crystals of iodide titanium at a temperature of 815°C. No significant changes in the types of slip and twinning planes were observed, but increased activity on the type I, order 1 pyramidal slip planes and on the type 11, order 2 twinning planes was reported. These planes contribute very little to the deformation process at room temperature.&apos;&apos; &apos; Since there is interest in titanium as a material for use at both low and high temperatures, the present investigation was undertaken to examine the slip and twinning behavior in coarse grained specimens of titanium at -—196", 500°, and 800°C in order to determine the general effect of temperature on the mechanism of plastic deformation. Experimental Material Used and Specimen Preparation—Both sponge and iodide titanium were used in the present investigation; chemical analyses appear in Table I. These materials were arc-melted under argon into 25 g slugs, which were then cold-rolled approximately 90 pct to a sheet thickness of 0.05 in. Since the strain-anneal technique was used for obtaining coarse grains, the cold-rolled sheets were made into tensile specimens which were then annealed to produce a relatively coarse uniform grain structure prior to critical straining. The details of the strain-anneal treatment. size of grains, and the method for preparing the specimen surface for optical microscopy have been described in a previous report.&apos; In order to obtain a wider spread in crystal orientation for the present work, it was necessary to vary the rolling schedule to reduce the degree of preferred orientation in the annealed sheets prior to critical straining. Methods for Tensile Testing—The apparatus for experiments at the temperature of liquid nitrogen (—196°C) consisted of two concentric stainless steel

Jan 1, 1957

By C. W. Sherman, John Chipman

IN the mathematical statement of the law of mass action, the activity of each substance consumed or produced in a reaction is used to obtain a numerical constant which is characteristic of the equilibrium of that reaction at the given temperature. The activity in many cases is equal to, or proportional to, the concentration. If this is the case, any units denoting concentrations, such as weight percentage or mol fraction, may be substituted in the equilibrium expression. It is even permissible to use mixed units provided only that each unit is that used in defining the activity of the corresponding substance. The indiscriminate use of concentration units in writing equilibrium constants sometimes leads to very erroneous results. On the other hand, what appear to be contradictory results from similar investigations often might be resolved if the activity is the quantity that is used to determine the equilibrium constant for the reaction in question. De-sulphurization serves as an important illustration. Sulphur in lron and Steel The control of the sulphur content of the finished product is one of the oldest and broadest problems in the metallurgy of iron and steel. In general, this control must be exercised through the action of a slag, and for this reason experimental studies of the distribution of sulphur between slag and metal have assumed considerable importance. Under slags of the type found in the basic open-hearth furnace the ratio (% S)/[% S] does not in general exceed about 8. Under blast-furnace conditions, however, de-sulphurization ratios of 50 to 100 are readily obtained, and under laboratory conditions using similar slags, the ratio may be as high as 400. The fact that blast-furnace metal is much more readily desulphurized than is molten steel rests upon two distinct phenomena. The first of these is connected with the slag reaction. In the open-hearth furnace, the equilibrium in the following reaction places a definite limit on the sulphur content of the slag: S + 0-- = 0 + S- - where the symbols underlined indicate elements dissolved in the liquid metal, while slag constituents are represented as ions. The high oxygen content of the open-hearth bath prevents this reaction from proceeding far enough to effect good desul-phurization. In the blast-furnace process, however, the oxygen activity is limited by the presence of carbon in the metal and in the coke bed and the controlling reaction becomes: S_+O- + C_=S- + CO(gas) [2] The second phenomenon which contributes to the easier desulphurization of blast-furnace metal is the effect of high concentrations of other elements. These elements, notably carbon, silicon, and phosphorus, increase the thermodynamic activity of sulphur several fold. As a result of this increase, the escaping tendency of sulphur from the metal phase is increased and its removal facilitated. Previous Studies It becomes, therefore, a matter of importance to determine the effects of various elements upon the activity of sulphur in the melt. The experimental approach to this problem has been made through the equilibrium between sulphur in the melt and gaseous atmospheres containing hydrogen and hydrogen sulphide. The reaction and its equilibrium constant are written as follows: S + H2(gas) =H2S(gas);K1 = -- [3] Pn2 • as where the symbol a, represents the activity of the sulphur in solution in the metal. The understanding of the chemical behavior of sulphur in steel and pig iron rests on a firm knowledge of the binary system Fe-S. A number of studies of the equilibrium have given closely agreeing results from which the activity and free energy of the dissolved sulphur may be found. The recent paper by Sherman, Elvander, and Chipman1 includes a discussion and quantitative comparison of the results of several of the significant researchesr-" on dilute solutions of sulphur in iron. The results of this study indicate that the relationship between the ratio Ph,s/p+ and the percentage of sulphur in solution is not a linear one. This

Jan 1, 1953

By John Marshall

THE purpose of this paper is to present to the profession data and experience obtained over a period of 5 years in the operation of 87 shaker-conveyor units, and the production of 2,169,638 tons of run-of-mine anthracite coal. The data are not generally available and should be of interest to those concerned with the operation of anthracite and bitu-minous mines. To simplify comparison, a ton of 2000 lb. of raw run-of-mine coal has been used as the production unit throughout this paper.

Jan 1, 1940

By C. Hirayama

THIS investigation was undertaken to determine some of the factors contributing to the embrittle-ment of glass-coated silver wire on heat treatment. The materials used in this investigation were 22 and 23 AWG silver wires obtained from Handy and Harman as "fine quality, soft temper." A wet analysis of one sample showed 99.8 pct Ag. The 23-gage wire was covered with a double layer (2.5 mils thick) of electrical grade fiber glass (aluminum borosilicate glass containing a relatively high concentration of calcium, and a very small amount of

Jan 1, 1960

By d&apos, L. Berenbaum, F. Heurle, R. Rosenberg

The structure of aluminum films obtained by evaporation was studied by electron microscopy, mostly by replica techniques and X-ray diffraction. The resistivities and stress conditions of the films were also determined. Film properties were studied as a function of source selection, substrate type, residual pressures of oxygen and water vapor, substrate temperature, and rate of growth. The formation of abnormal localized growths and whiskers resulting from annealing treatment subsequent to deposition was investigated. Films deposited onto single-crystal substrates were found to be epitaxially 0riented; for such films, relative orientations between films and substrates were determined. ALTHOUGH wide use has been made of evaporated aluminum films for the formation of conducting lines on semiconductor devices, relatively little has been reported concerning the structural characteristics of such films.1"9 The purpose of this study was to obtain an overall view of the dependence of these characteristics on film deposition and subsequent annealing conditions, which were similar to those used in silicon planar technology. Accordingly, most of this study was carried out using oxidized and bare silicon wafers as substrates, although some work was also done using alkali halide, magnesium oxide, and mica substrates. However, the main concern remained pragmatic. Emphasis was given to the study of the effects of deposition and annealing conditions on film characteristics such as structure, resistivity, and stress. I) EXPERIMENTAL PROCEDURES The films which were investigated in this study were deposited in 18-in.-diam glass chambers which were connected to the usual type of trapped diffusion pumps filled with silicon oil. Through the use of liquid-nitrogen-cooled Meisner traps and titanium sublimation pumps placed inside the deposition chambers, the pressure could be lowered to the lower portion of the 10- I Torr range and little increase in pressure would occur during the deposition cycle. Unless described otherwise, the substrates were 1-in.-diam p-type silicon wafers having a resistivity of 10 ohm-cm. The wafers were oxidized in wet oxygen at 975°C followed by a short dry-oxygen exposure at the same tempertture to a total oxide thickness of approximately 6000A. The wafers, backed by a layer of gallium, were mounted onto molybdenum discs brazed to a copper block.10 The latter was heated by imbedded commercial cartridge heaters. The substrate temperature could be maintained to within +10°C of a prescribed temperature during film deposition. The search for a satisfactory source for the controlled evaporation of aluminum has led to the use of 1-in.-diam crucibles" machined from rods of a commercially available, refractory composite* of Bn and

Jan 1, 1969

By G. A. Vissac

MoIstuRe in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain"). These latter forms of moisture are particularly common in "young" coals (subbituminous and lignites); bloom coals (seam outcrops); fusain; and carbonized products. In our study of coal drying, we shall consider only the removal of free moisture, exclusive from hygroscopic moisture. Dewatering If we reserve the name of drying to the removal of water by evaporation, we must consider the initial phase of the mechanical removal of free moisture as a distinct operation covered by the term dewatering. In all cases the free water carried over the surface of the coal particles or in their interstices, or in their pores, is retained by capillary forces. Dewater-ing is accomplished by breaking or counteracting these capillary forces; removal of as much water as possible by dewatering methods is usually advisable, as the cost of these operations is generally much less than by evaporation. The most common methods of me-chanical dewatering are: 1. "Pressure piling," which reduces the interstitial spaces, accomplished in dewatering bins or over dewatering screens. 2. Or dynamic methods, such as used in centrifuges or over vibrating screens. We shall only mention the " preferential wetting" method, in which surface water can be displaced by hydrocarbons, as offering possibilities, but which, to our knowledge, has not reached yet a practical development. But we must point out that the capillary forces retaining water on the coal surfaces, decrease considerably with increased temperatures. This is the principle used in all modern dishwashing machines; by using very hot water, dishes are extracted almost dry. In line with this development, we favor the type of dryers including a dewatering section; as the coal enters the dryer and is gradually brought up to higher temperatures, its dewatering ability is increased and advantage can be taken of this conditioning, resulting in increased drying efficiencies and reductions in drying costs. Heat Drying In the final phase, the remaining moisture must be evaporated. Coal and water must be brought up to the chosen temperature of evaporation, and heat must be supplied to fill the requirements of the latent heat of evaporation of the water to be removed. Accordingly, drying becomes largely a problem of heat transfer, and drying methods can be classified accordingly, namely: 1. Radiant transfer. 2. Transfer by surface contact and conduction. 3. Transfer by hot gas contact. The first method is not applicable to coal drying; the second method is used in the old type rotary dryer. The third method, the most commonly used in modern coal dryers, will be the only one considered here; and, of course, we shall deal with continuous types of dryers only. The mechanism of complete drying is really very complex-—several phases are involved: 1. The constant rate period. 2. The uniform falling rate period. 3. The varying falling rate period. As most of our practical coal drying problems deal with wet coals (over 6 pct of moisture), and do not require complete drying (under 1.5 pct), we shall deal with the first condition only, namely the constant rate drying. Dryer Calculations Instead of presenting the algebraic formulas, we believe a concrete example will provide a clearer illustration. Assume a feed of wet coal at the rate

Jan 1, 1950

By Lyman H. Hart

Some of the significant facts that will affect the supply and demand for metals during the next few decades are given in this presentation. This is important because the only hope for intelligent guidance of the national destiny depends upon presenting a consistent and accurate picture of basic problems. The metals problems now fomenting are only slightly less important than those precipitating the energy crisis. Admittedly, it is difficult to generate serious thinking on this subject when the world is enjoying easy access to all metals at modest prices. This is possible because of the current world capacity to over-produce, and United States credit standing, at least up to now, has permitted buying freely on world markets. Although both these vital conditions are subject to change, there is little doubt that if the U.S. financial house is kept in order, we can muddle along for a while on a generally expanding, metal-based economy. But should our credit standing be permitted to collapse, or should there be a tightening of world supplies of metals, the nation would immediately find itself in trouble. Unfortunately, clear signals indicate that both of these conditions are threatening. The metal age started many centuries ago, and with the exception of the noble metals, barely a dent was made in world reserves until the present century. Then, as a result of the pioneering ideas of D. C. Jackling and Paul Gemmel, and the willingness of the McNeals, Penroses and Guggenheims to back ideas with money, a virtual explosion of metal production was propagated throughout the world. It is important to examine the causes of this expansion to determine whether it is a trend that may be sustained or whether it is anomalous and therefore attributable to circumstances not likely to be repeated or continued. This period of plenty is a once only phenomenon. Vast metal resources have been sitting around here for eons, while the world was unaware of or unconcerned with their existence. But when population began to grow exponentially, and ways were discovered to use metals to develop machines to do the work of men and animals, the exploitation of raw materials increased at a staggering rate. And now the realization is dawning that minerals are a wasting asset and are beginning to present supply problems that should begin to be of concern. Two main factors have caused this condition; One is the population growth, and the other is the expanding demand for irreplaceable raw materials as nations become more developed. A group of systems analysts, at Massachusetts Institute of Technology in a book Limits of Growth, has warned that at present rates of population growth and resource consumption together with environmental constraints, a point will be reached within 100 years when the world population will become totally incapable of supporting itself. The authors conclude that this end result could be avoided if a planned equilibrium could be established at a lower rate of population growth and resource consumption. Fortunately, there is evidence that the population problem is moderating. The growth rate in the U.S. has decreased from 2.3% per year in 1900 to 1.1% in 1970. But, even at the lower rate, population will double in 70 years. The world rate is greater, and if it continues, world population will rise from 3.5 billion to nearly 10 billion in 50 years. All of these projections are questionable because the dangers of growing population are now being recognized. A marked decrease in growth rate has been noted in the more developed countries-in fact, it was zero in the U.S. in 1972. The other factor affecting consumption of raw materials is the increase in per capita use of most items as individuals become more affluent. Many economists believe that developing countries such as China and India represent a vast future potential market; but there are others, with whom the author agrees, who believe over-population tends to stagnate development. Nevertheless, it is a fact that vigorously developing societies increase consumption at a rate far above their population growth rate.

Jan 1, 1974

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

By R. D. Stover, F. O. Shuck

The variation of binary-diffusion coefficients with composition in the liquid Bi-Sn system at 300°C was measured using the capillary-reservoir technique. The experimental coefficients did not exhibit a simple composition dependence. A number of tests were also made to determine the effect of variation of density with composition on convection within the capillaries. These tests indicate that the density changes arising from composition duferences may give rise to high diffusion coefficients unless care is taken to maintain a stable configuration. In recent years there has been considerable interest in diffusion in liquid metals. However, the bulk of the work done to date has involved measurements of self-diffusion or diffusion of dilute concentrations of "solute" metals. Because there are possible applications to liquid phase processing of metal alloys and since additional data may help to clarify the nature of diffusion in liquid metals, investigations of the concentration variation of diffusion coefficients in binary alloys have been undertaken. Of past studies only two have covered large ranges of binary composition. Niwa et al.&apos; investigated the Pb-Sn, Bi-Pb, and Bi-Sn systems and Grace and Derge2 investigated the Bi-Pb system. Because of the discrepancy between the data of these investigators, it was deemed desirable to check the possibility of convection arising from the variation of density with composition. The capillary-reservoir technique of Anderson and saddington3 was chosen for the present investigation since it has been widely used for measurements involving dilute solute concentrations and it was the technique used by Grace and Derge.2 It was necessary, however, to modify the normal procedure of using a pure metal bath to avoid measurement of integral diffusion coefficients over large concentration ranges. The alloy system chosen for study was the Bi-Sn system for which there are some data available.&apos; EXPERIMENTAL PROCEDURE In order to utilize the capillary-reservoir technique for measurements of diffusion coefficients as a function of composition, it was necessary to modify the normal procedure slightly. This modification consisted of using a reservoir composition which was only slightly different from that in the set of capillaries, in order that the integral coefficients measured might be taken over a small composition range and might thereby be assumed to approximate the differential coefficient at some average composition between that of the capillary and that of the bath. It was found that a composition difference of approximately 0.10 mass fraction provided a satisfactory compromise between a small increment in composition and reasonable accuracy in measuring changes of composition. The alloys were prepared from tin and bismuth of 99.999 pct purity. The materials were first cleaned of surface oxides, then weighed and melted to form a homogeneous alloy in a Pyrex filling apparatus. The capillaries used were of precision bore Pyrex tubing 1.000 *0.005 mm bore. Capillaries of various lengths (from 2.85 to 5.85 cm) were cut and sealed at one end by fusing a 3-mm Pyrex rod to the end. The capillaries were filled by inserting them into the filling chamber, evacuating the chamber, submerging the capillaries, and pressurizing the chamber with argon. Two sets of capillaries were prepared for each run. One set contained an alloy more dense than the bath alloy and one set a less dense alloy. This procedure was followed so that the effect of density difference on the measurement could be determined. After filling one set of capillaries, these were placed open end up in a capillary holder and transferred to the diffusion chamber which consisted of a Pyrex tube inserted into a graphite block. The second set of capillaries was then filled and placed into the diffusion chamber. The reservoir alloy, which had been melted in a separate crucible, then was poured carefully into the diffusion chamber. Sufficient reservoir alloy was used to cover all capillaries to a depth of several centimeters. All of these operations: capillary filling, melting of alloys, and diffusion anneal, were carried out in a fused-salt bath which maintained a temperature of 300"*1°C. All capillaries were permitted to diffuse for approximately 48 hr. At the end of the diffusion period the capillary holder was removed from the bath and

Jan 1, 1969

By James A. Barr

The writer&apos;s first experience with flotation was during World War I, in the bene-ficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added&apos; The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals separation mechanical flotation machines were used in another graphite mill. pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"† using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the phosphate Recovery corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for bene- ficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., sub-,,,tion types, with weir control of pulp between cells. The sand bleeders were very small—about 1¼-in. diameter. As the feed flake. Is to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. 1 and details of the cascade construction in Fig. 2. The cascade installation in plant NO. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1947

By James A. Barr

The writer&apos;s first experience with flotation was during World War I, in the bene-ficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added&apos; The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals separation mechanical flotation machines were used in another graphite mill. pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"† using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the phosphate Recovery corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for bene- ficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., sub-,,,tion types, with weir control of pulp between cells. The sand bleeders were very small—about 1¼-in. diameter. As the feed flake. Is to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. 1 and details of the cascade construction in Fig. 2. The cascade installation in plant NO. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1947

By Milton E. Wadsworth, J. Brent Hiskey

Galvanic interaction between particulate chalcopyrite (CuFeS2) and copper results in the rapid conversion of chalcopyrite to chalcocite. The effects of temperature, surface area, concentration of sulfuric acid and agitation were systematically evaluated. The kinetics were found to be controlled by a steady-state current flow controlled by the effective anodic and cathodic surface areas involved in the galvanic couple. The experimental activation energy was 11.5 and stoichiometric data and reaction products have been characterized. The overall kinetic system has been evaluated based upon an electrochemical model.

Jan 1, 1974

By P. E. Busby, C. Wells, M. E. Warga

Fundamental data on the rate of diffusion of boron in austenite and solubility of boron in the a and y phases of iron and steel have been obtained from deboronizing experiments and provide partial explanations for some of the phenomena observed in boron steels. The rate of diffusion of boron is about the same as carbon in austenite. The solubility of boron in austenite at normal heat-treating temperatures is less than 0.001 pct. A partial tentative Fe-B phase diagram in the important low boron concentration ranges and an equation representing the diffusion of boron in austenite are presented. A LTHOUGH a search of the literature revealed ALTHOUGHthat boron diffusion had not been studied quantitatively and systematically prior to 1948, a few qualitative observations which were made by following the diffusion of boron into iron packed in ferro-boron1-3 suggest that boron obeys normal diffusion laws and that the rate of diffusion increases with increasing temperature. The claim of Cornelius and Bollenrath1 that boron does not appear to influence the rate of carbon diffusion has recently been substantiated by Wells, Batz, and Mehl.4 Calculations based on data from the paper by Campbell and Fayv indicated that the diffusion coefficient (D) for boron in iron at 900°C is approximately 3x10 sq cm per sec; a value of 2x10-7 sq cm per sec at 1038°C has been reported by Digges et al in connection with decarburizing experiments on a commercial boron steel containing 0.43 pct C. During the period 1948 to 1950 several diffusivity constant (D) values for the diffusion of boron in the y phase of iron and steel and a number of solubility values for boron in both a and y phases were reported. It was concluded tentatively as a result of Metals Research Laboratory studies that D values for boron in y and a phases are about the same as for carbon in the comparable phasesa and that carbon up to 0.4 pct did not affect the rate of diffusion of boron in y iron above 1000°C within the limits of experimental error. Whether saturation of the y or a phases with carbon would significantly affect rates of diffusion of boron through them was then and still remains in doubt. The best estimate of Q (activation energy) was reported to be about 25,000 cal, somewhat lower than that for carbon in y iron. The solubility of boron in y iron at 1000°C was thought to be higher than 0.004 pct B but not as high as a more recent analysis of available data shows it to be. The solubility of boron in a iron at 700°C was reported to be 0.0004 pct B, but it would not have surprised the authors if the true solubility value is actually lower than this. Breaks in diffusion curves which were not understood when first obtained prior to 1950 have now been recognized as indicating solubility limits, and these are included in the present paper. Experimental Procedure Two methods were employed in an effort to determine diffusion coefficients (D) for boron in austenite. Early experiments involved the use of welded couples prepared in accordance with the procedure of Wells and Mehl,&apos; but when the results of these experiments proved to be unsatisfactory for calculating D values, studies were continued by means of deboronizing experiments. In both cases, boron analyses following the diffusion anneal were carried out spectrographically and all D values were computed using the Grube solution of Fick&apos;s law. The precision of the spectrographic method used proved to be about equal to that reported by Corliss and Scribner" —average deviation from the mean about 5 pct of the amount present when the boron content is 0.003 pct. Concentration-penetration curves obtained from spectrographic analyses of welded couples generally indicated that practically no boron was transported across the weld interface during the diffusion anneal. Furthermore the concentration-penetration

Jan 1, 1954

By Alexander Bowie

In many places throughout the Western mountain plateau regions of the United States coal beds in place have been burned over very extensive areas, the fire evidently originating on the nakedly exposed outcrop of the coal bed and gradually burning its way into the bed for considerable distances under very heavy cover. The surface evidences of the burned-out coal beds are seen in the calcined and discolored rocks overlying the places of the outcrops. The greater the mass of the burned coal the higher the results of its combustion can be seen in the overlying strata. I have noted many instances of this condition in the States of South Dakota, Wyoming, Colorado, New Mexipo, and Arizona. In the lignite fields of Dakota and Wyoming I noted stretches of level country many square miles in extent where the surface rooks were roasted and vitrified by the burning of a great bed of lignite lying nearly level and with a light cover; this is probably the most favorable natural condition for the burning out of a coal bed. The less the depth of the rock covering overlying the coal bed, the better the chance for a continuous supply of air to the fire; but when the coal bed dips heavily into the ground, or even if level, if it passes under a hill or mountain which gives the bed a heavy covering of strata, the fire has more chances of being extinguished from natural causes than in the first condition described. The distance which a crop fire may extend into a coal field is very much influenced by the dip, the thickness of the coal bed, and the nature of the rock covering immediately overlying it. In reasoning on this subject, it would seem logical to assume in the case of a coal-bed cropping at the base of a hill and dipping into it, with an extensive drainage surface above the crop line, that a crop fire would be promptly extinguished by the caving in of the overlying strata and the precipitation of the rainfall from the drainage surface above the outcrop through the breaks formed in the caving strata. This consideration would be more or less effective according to the climate of the location and the nature of the overlying strata. In a humid climate where the rainfall was heavy the water from the natural precipitation alone would probably extinguish a crop fire before it could work its way very far under cover, but in an arid climate this preventive does not seem to be effective.

Jan 1, 1915

By Helmut Thielsch

IN recent years an ever increasing amount of interest has been directed toward research studying the principles and various applications of sonic and supersonic waves. Though still in their early stages of practical development, sonic vibrations are already used in the emulsification and degasification of liquids. Metals exposed to sonic or ultrasonic vibrations while solidifying show a considerable amount of grain refinement. Often sound waves are applied instead of radiography to test engineering materials for internal cracks and flaws.1 In the field of pure research these waves are used in dispersion and also in coagulation of particles or liquids in gaseous or, under certain conditions, in other liquid systems. In the settling and thickening of slurries considerable time is necessary to compress the solid particles and to squeeze out the liquid to obtain as low a dilution (liquid to solid ratio) as possible. Various methods have been developed to increase the amount of coagulation of the very fine solids (colloidal or semicolloidal) and to shorten the over-all time. The addition of small amounts of electrolytes and the warming of the suspension represent merely the more important techniques. Some of the effects of supersonic vibrations have been reported previously.2,6 From preliminary studies, therefore, it was hoped that by application of sonic vibrations it would be possible to reduce the time required to thicken such materials to a specific dilution, as well as to thicken to lower ultimate dilutions than could be obtained by quiescent settling alone. By increasing the volume thickened per unit time-i.e., improving the plant efficiency-great savings in equipment and time would be obtained for industrial processes. Also, faster settling rates should result if coagulation of particles could be increased. Experiments have been conducted for a period of several months in the Allis-Chalmers laboratory to study the effect of sonic vibrations on settling of particles of different sizes and concentrations. APPARATUS The sedimentation apparatus used in these experiments is illustrated in Figs. I and 2. The essential features are the stationary field coil and the movable voice coil. Both windings are placed around a solid iron core. A leather diaphragm connected to the steel frame holds the voice coil in place. A brass rod is fastened to the voice coil with a metal disk connected to the other end. This disk is sealed to the lucite cylinder with a flexible rubber diaphragm. The lucite tube is 17 in. long; its inner diameter is 2 ½in. and the wall thickness is ¼ in. The tube is calibrated on the outside in 10 c.c. divisions for a total of 1000 cubic centimeters.

Jan 1, 1946

By G. M. Schwartz, G. A. Thiel

THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snelling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipestone and elsewhere in southwestern Minnesota: The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation, in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota&apos;s production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowled and by Thiel and Dutton.2 The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.3 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on&apos; the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1-Central Minnesota in the region of the city of St. Cloud, 2-the upper Minnesota River valley region, 3-the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in. their dis-

Jan 1, 1952