Search Documents

By H. C. Rogers

It has been shown previously'- 3 that when a mild steel or iron is charged with hydrogen, the normally observed yield point is eliminated or considerably

Jan 1, 1960

By R. B. Rosene, G. L. Foster, A. R. Hendrickson

he properties of some of the common fracturing oils, such as sand-falling rate, fluid loss and viscasity, are a function of the three major constituents of the oil. These are: asphaltic material, parafin waxes and a base oil. The base oil can be either high or low viscosity. Asphaltic material increases viscosity by thickening the oil, decreasing the rate of fall of sand through the oil. at temperatures up to 200" F. When large arnorrnts of parafin wax are present, much of the wax i.s not dissolved, but is present in the form of rnicroscopic crystals. 7'his, of course is limited to temperatures below the melting points of waxe.s. As a result, parafin waxes clo not function primarily as thickener.7, but rother as bullting materials. The functiori of wax, without asphaltic material, in a low viscosity base oil is uniquely unlike that of wax with asphalt coexistent in the oil. The resulting difierence in wax crystal size governs the sand-falling rate to a large extent. An ideal type of fracturing oil is one containing neither asphalt nor waxes. In such cases, the viscosity and resulting low sand-falling rate are apparently due to soluble resin- ous hydrocarbons, which are compatible with formation oils. INTRODUCTION Since the introduction of hydraulic fracturing as a method of stimulating production from oil and gas wells, a variety of fluids have been employed to open the fractures and carry the propping agent. Such fluids include gels, emulsions, and oils. In the latter category, the use of refined oils has increased tremendously, and it is probably safe to assume that such oils represent more than one-half of the total fluid used in fracturing. The general acceptance of refined oils for fracturing can be accounted for on the basis of their relatively low cost and general applicability. To minimize transportation costs, such refined oils are generally obtained within the local areas of operation. As a result there are several kinds of oil used in different areas, with a wide variation in the basic composition. These types may vary from a fair grade of lubricating stock to a highly viscous cut-back asphalt. or road oil. Originally, little attention was paid to the composition of the oils used for fracturing, and any oil which would carry sand was considered satisfactory. Recently, however, service companies and well operators have become more concerned with the type of oils used for fracturing. With this in mind, the present work was undertaken to evaluate and compare many widely used fracturing oils to determine which constituents were most desirable for fracturing purposes. Some of the important properties of fracturing fluids are sand-falling rate, viscosity, and fluid loss. Other properties, that are actually of no less importance, include flash point, pour point, emulsifying tendencies with formation brines, and compatability with the formation oils. This discussion has been limited, however, to the first mentioned properties in order to give some idea of the general composition of the refined oils, how they function, and why. PROPERTIES OF FRACTURING OILS The properties of fracturing oils are a function of the three major constituents of the oil. These may be designated as: (1) asphaltic material, (2) paraffin waxes and (3) a base oil, which may be of either high or low viscosity. The asphaltic material clas-

Jan 1, 1956

By R. Stefanko

The use of strain gauges and compression pads for an underground bolt installation in a central Pennsylvania coal mine revealed that satisfactory anchorage could not be maintained in the shale stratum that constituted the immediate roof. Comprehensive laboratory tests resulted in a new shell designed with an increased area of contact and smaller surface serrations. Retightening of the bolt was also found to be beneficial for maintenance of high load values. Roof bolting in coal mines has progressed very rapidly in the last decade, and today this method of support is in general use. There are many theories concerning the functions of roof bolts, but the importance of beam building is indisputable. Proper tension in the bolts minimizes shearing along bedding planes and creates a thick, competent beam from individually weak layers. Bolting must be accomplished immediately upon exposure of the roof, and bolt tension must be maintained if roof failure is to be prevented. Seams are being mined today with roof bolt support where conventional timbering was not effective.' The widespread use of continuous mining equipment was made possible by roof bolts which permit long supported spans free of obstructions. Since adequate anchorage is the key to successful bolting, better methods for determining the efficiency of anchorage are continually being sought. Attempts have been made to measure bolt loads, thus assessing anchorage efficiency by employing sensing devices between the bolt head and roof. 3-s None of the techniques appears to be very accurate, and all have at least one serious deficiency. The greatest efforts are being directed toward the standardization of the pull test.6" Nevertheless, the author believes that the pull test is only one criterion for establishing the efficiency of anchorage and not necessarily the most important one. The conventional pull test involves the short-term application of forces, whereas the success of roof bolt installations is dependent upon the ability of anchorage to sustain relatively long-term forces. Therefore, it would appear that the time-dependent function of the anchor is the single most important parameter for the success of roof bolting in many types of rocks. UNDERGROUND TESTS Strain gauges and compression pads were employed to measure bolt loads in a central Pennsylvania coal mine.8 Bolting had been employed only sporadically in the shale top since dubious benefits were obtained with this type of support. Table I shows some typical results from this investigation. Anchorage losses were extremely variable among the bolts, but all showed a considerable degree of bleed-off. The tests indicated that anchorage efficiency was extremely low in this type of shale. The results confirmed that bolting under these conditions was practically worthless, and thus a waste of material and labor. Probably even more important, bolting constituted a hazard when reliance was placed upon it for support. Certainly the complete lack of confidence in roof bolting, which was apparent in the mine personnel, was justifiable since the bolts did not accomplish their purpose. PRELIMINARY LABORATORY BOLT TESTS The extreme losses in bolt tension that were detected in underground installations prompted a comprehensive study to assess the causes. However, preliminary studies were first made to determine the combined stresses in a roof bolt and to prove conclusively that the observed bleed-off phenomena were due to anchorage: slippage and not to some other physical manifestation. In all of the ensuing tests

Jan 1, 1962

By Adam L. Wesner, A. C. Richardson

DURING World War II the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pet iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pet of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The -10 +35 mesh fraction was found to be the most promising feed for producing the low-ash [ ] content coal. A batch of 30 tons of -3/8-in. coal was screened at 10 and 35 mesh; the yield of -10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the -35 +48 mesh range. A representative portion of the -10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pet ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1952

By F. von Gemmingen, E. J. Fasiska, L. Zwell

EARLIER studies of the dependence of creep on structure1 and of the dependence of creep rupture on creep behavior2 did not include detailed discussion of the phases present in the specimens under examination. It is of interest to determine the nature and amounts of such phases present since it is well known that these are dependent on composition, heat treatment and creep conditions.3 This investigation has therefore been undertaken to identify these constituents and to determine their relative amounts. This report presents the results of this investigation and describes an improved "extraction replica" technique developed in the course of the work. The composition of the Type 316 austenitic stainless steels studied in this investigation is given in Table I. The specimens were solution treated at 2000°F for 1/2 hr and water quenched. Those specimens subjected to prestrain at room temperature Methods for extracting precipitate particles from materials for electron and X-ray diffraction analysis have been described by Fisher,4 Smith and Nutting: and Booker and coworkers.6'7 Electrolytic extraction methods have been described by Andrews and Hughes.8 The first two methods have been used at this Laboratory, but have not proved satisfactory for many problems requiring X-ray diffraction analysis. It has been difficult to remove the replicas or to avoid tearing them during removal. These difficulties are overcome by backing the replica with a water-soluble plastic such as Dupont 51-05 Elvanol (polyvinyl alcohol). The backing increases the thickness of the replica so that it can be mechanically stripped from unloosened particles without folding or tearing. This procedure eliminates the stripping of wet replicas, which usually have a low tear strength. By stripping replicas after drying, it is possible to extract partially loosened particles which otherwise would remain imbedded in the metal. The modified method is as follows: after the specimen is polished, it is etched for 60 min in modified glyceregia consisting of 30 ml glycerol, 7 ml nitric acid, and 4 ml of hydrochloric acid. The sample is then washed, air dried, and coated with a 20 pct Baker and Adamson 1611 collodion (85 pct amyl acetate by volume) film. After the collodion film is dry (about 15 min), the sample is again etched in the modified glyceregia for 50 min, washed with isopropyl alcohol (to prevent dissolving the collodion) and air dried. A very thick coat of polyvinyl alcohol (about 50 pct solution "Elvanol Dupont 51-05" in water) is poured over the sample and is permitted to dry for about 24 hr. The composite film containing the precipitates is then stripped from the specimen and floated, polyvinyl alcohol side down, in water (at about 50°C) until the polyvinyl alcohol dissolves. This usually takes about 15 min. Should any of the polyvinyl alcohol remain on the replica, it does not give a crystalline diffraction pattern and therefore does not hinder identification of the precipitates. The extraction replica, floating in water, is picked up on a glass fiber and mounted in the Debye-Scherrer camera for X-ray diffraction analysis. Concentration of the etchant, and also etching time, had to be increased for several of the samples. Fig. 1 shows two extraction replicas taken from different areas of spec. M74-37; X-ray analysis showed a strong diffraction pattern of M23C6 and a medium one of u phase. A

Jan 1, 1962

By W. P. Evans, R. W. Buenneke

Warren and Averbach's multiple order, Fourier method was applied to solid specimens of SAE 1045 steel. The material was hardened to three hardness levels and specimens of each hardness were shot peened to three intensities. Particle size, root-mem-square strain, mean strain, md macro residual stress were determined for each. Microstrains caused by either hardening or peening varied markedly over microregions. In general, increasing the hardness or peening intensity increased the rms strain and decreased the particle size. Similar effects were observed by varying hardness and peening intensity independently. At a Rockwell hardness of C 50, peening had little effect on line broadening, but both mean strain and macro residual stress increased. Mean strain was independent of column length. Induced macro residual stress by peening was affected most by initial hardness, but not by specific peening intensity. The purpose of this work is to establish the state of residual strain and particle size by X-ray diffraction in hardened and cold-worked plain carbon steel and attempt to relate these X-ray measured parameters to fatigue performance. X-ray line broadening (and its micro implications), along with X-ray residual stress (and its macro implications), may be basic indicators of the inherent fatigue resistance of the material. X-ray line broadening is caused by variable lattice strains and small particle size. Both are a result of plastic deformation which accompanies hardening or cold working processes. Therefore, X-ray line broadening is a good measure of both. warren1 has recently reviewed the Warren and Averbach2,3 Fourier analysis of line broadening. Strain and particle size effects can be separated because broadening due to particle size is independent of order of the diffraction peaks, while broadening due to strain is not. Microstrain is obtained as a root-mean-square strain averaged over discrete distances within the crystals causing diffraction. These distances are quite small, varying from 10 to 10081, and may be interpreted as the gage length over which the strains are averaged. Because of their variable nature, the X-ray line is broadened. The plot of rms strain vs distance (or column length) within the specimen gives a measure of their variability. Small particles also cause X-ray line broadening as already mentioned. A particle is interpreted as a region within a crystal or grain which diffracts X-rays coherently. This region is one of given orientation and may be bounded by a small angle grain boundary, dislocations, a twin boundary, or a stacking fault. The present work covers measurement of X-ray line broadening and macro residual stress on an SAE 1045 steel, quenched and tempered to various hardnesses. Various amounts of cold working were produced by shot peening the surfaces to various Almen intensities. Particle size, root-mean-square strain, and mean strain were calculated from the Fourier coefficients of the X-ray diffraction profiles in a direction normal to the peened surface. No effort was made to separate the various causes of particle size broadening. Macro residual stresses were reported in directions parallel to the peened surface. I) X-RAY METHOD The Fourier coefficients were determined for the 110 and 220 X-ray profiles. They were corrected for instrumental broadening by the method of Stokes,4 using an annealed reference specimen of similar geometry presumed to be free from broadening due to small particles and distortions. The nth Fourier cosine coefficient, A,, is related to a particle size coefficient, Ap, and a distortional coefficient, ADn, by the equation:

Jan 1, 1963

By Cyril Stanley Smith

BETA brass (consisting of approximately equal atomic proportions of copper and zinc) exists as a random solid solution at high temperatures, but at low temperatures [ ] an ordered structure is stable, with the copper and zinc atoms occupying alternate sites on the body-centered-cubic lattice. On cooling, ordering commences at a temperature of 450° to 470°C., depending on the composition. The degree of ordering progressively increases at lower temperatures until it becomes virtually complete at about 100°C. The electrical resistivity of the alloy illustrates the changes clearly (Fig. I). This type of reaction has been a favored subject for study by physicists. An [ ] excellent summary of the theory is to be found in a paper by F. C. Nix and W. Shockley.1 All published data on electrical conductivity, specific heat and other properties agree in indicating that the ordering reaction in beta brass takes place so rapidly that it cannot be prevented or even retarded by quenching. With most ordered alloys, cold-working induces disorder and

Jan 1, 1942

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By Frank G. Miller

This report presents developments of fundamental equations for describing the flow and thermodynamic behavior of two-phase single-component fluids moving under steady conditions through porous media. Many of the theoretical considerations upon which these equations are premised have received little or no attention in oil-reservoir fluid-flow research. The significance of the underlying flow theory in oil-producing operations is indicated. In particular, the theoretical analysis pertains to the steady, adiabatic, macroscopically linear, two-phase flow of a single-component fluid through a horizontal column of porous medium. It is considered that the test fluid enters the upstream end of the column while entirely in the liquid state, moves downstream an appreciable distance, begins to vaporize, and then moves through the remainder of the column as a gas-liquid mixture. The problem posed is to find the total weight rate of flow and the pressure distribution along the column for a given inlet pressure and temperature, a given exit pres5ure or temperature and given characteristics of the test fluid and porous medium. In developing the theory, gas-liquid interfacial phenomena are treated. phase equilibrium is assumed and previous theoretical work of other investigators of the problem is modified. Laboratory experiments performed with specially designed apparatus. in which propane is used as the test fluid, substantiate the theory. The apparatus. materials and experimental procedure are described. Comparative experimental and theoretical results are presented and discussed. It is believed that the research findings contributed in this * paper should not only lead to a better understanding of oil-reservoir behavior, but also should be suggective in regard to future research in this field of study. INTRODUCTION In recent years much time and effort has been consumed in both theoretical and experimental studies of the static and . dvnamic behavior of oil-reservoir fluids in porous rocks. Although lack of sufficient basic oil-field data, principally concerning the properties and characteristics of reservoir rocks and fluids, largely precludes quantitative application of research results to oil-field problems, qualitative application has become common practice. In effect. oil-reservoir engineering research is serving as a firm foundation for oil-field development and production practices leading to increased economic recoveries of petroleum. This province of research. however, still poses many perplexing problems. The thermodynamic behavior of two-phase fluids moving through porous media constitutes one facet of reservoir-fluid-flow research that has not received the attention it deserves. This report embodies a theoretical discussion of this subject and a description of a series of related laboratory experiments. The significance of the problem to oil field operations is indicated but in articular the report centers around a theory and method for analyzing the steady. macroscopically linear, two-phase flow of a fluid (a single molecular species) through a horizontal column of porous medium. For simplicity in showing how the thermodynamic behavior of two-phase fluids moving through porous media affects oil-reservoir performance problems, attention is focused temporarily on a particular well producing petroleum from an idealized water-free solution-gas drive reservoir, the reservoir rock being a horizontal, thin, fairly homogeneous sandstone of large areal extent confined between two impermeable strata. The flowing hydrocarbon fluid is considered to exist entirely as a Iiquid at points in the reservoir remote from the well; however. the decline in fluid pressure in the direction of the well causes vaporization of the hydrocarbon to begin at a radial distance r from the well. Upstream from r the fluid moves entirely as a liquid and downstream from r it moves either entirely as a gas or as a gas-liquid mixture depending on the properties of the hydrocarbon and on the thermodynamic process it follows during flow. The distance r would be variable under transient flow conditions. but for purposes of analysis the flow is considered to l~e steady at the particular instant of observation during the flowing life of the well of interest. If the flow were isothermal and the hydrocarbon a pure substance, the fluid would be entirely gaseous downstream from r. Thus, this isothermal flow process for a pure substance would require that the heat of vaporization be supplied at r. over zero length of porous medium, at the precise rate necessary to maintain the constant temperature. This means that the solid matrix of the porous medium (reservoir rock) and the surroundings (impermeable strata confining the reservoir rock) would have to serve as infinite heat sources. Heat-transfer requirements would be somewhat less severe for the isothermal flow of a multicorn-ponent hydrocarbon as bubble and dew points at the same temperature correspond to different pressures. In this instance isothermal conditions would be sustained without complete vaporization of the fluid over zero length of porous medium. Nevertheless. as the flow is in the direction of decreasing

Jan 1, 1951

By Frank G. Miller

This report presents developments of fundamental equations for describing the flow and thermodynamic behavior of two-phase single-component fluids moving under steady conditions through porous media. Many of the theoretical considerations upon which these equations are premised have received little or no attention in oil-reservoir fluid-flow research. The significance of the underlying flow theory in oil-producing operations is indicated. In particular, the theoretical analysis pertains to the steady, adiabatic, macroscopically linear, two-phase flow of a single-component fluid through a horizontal column of porous medium. It is considered that the test fluid enters the upstream end of the column while entirely in the liquid state, moves downstream an appreciable distance, begins to vaporize, and then moves through the remainder of the column as a gas-liquid mixture. The problem posed is to find the total weight rate of flow and the pressure distribution along the column for a given inlet pressure and temperature, a given exit pres5ure or temperature and given characteristics of the test fluid and porous medium. In developing the theory, gas-liquid interfacial phenomena are treated. phase equilibrium is assumed and previous theoretical work of other investigators of the problem is modified. Laboratory experiments performed with specially designed apparatus. in which propane is used as the test fluid, substantiate the theory. The apparatus. materials and experimental procedure are described. Comparative experimental and theoretical results are presented and discussed. It is believed that the research findings contributed in this * paper should not only lead to a better understanding of oil-reservoir behavior, but also should be suggective in regard to future research in this field of study. INTRODUCTION In recent years much time and effort has been consumed in both theoretical and experimental studies of the static and . dvnamic behavior of oil-reservoir fluids in porous rocks. Although lack of sufficient basic oil-field data, principally concerning the properties and characteristics of reservoir rocks and fluids, largely precludes quantitative application of research results to oil-field problems, qualitative application has become common practice. In effect. oil-reservoir engineering research is serving as a firm foundation for oil-field development and production practices leading to increased economic recoveries of petroleum. This province of research. however, still poses many perplexing problems. The thermodynamic behavior of two-phase fluids moving through porous media constitutes one facet of reservoir-fluid-flow research that has not received the attention it deserves. This report embodies a theoretical discussion of this subject and a description of a series of related laboratory experiments. The significance of the problem to oil field operations is indicated but in articular the report centers around a theory and method for analyzing the steady. macroscopically linear, two-phase flow of a fluid (a single molecular species) through a horizontal column of porous medium. For simplicity in showing how the thermodynamic behavior of two-phase fluids moving through porous media affects oil-reservoir performance problems, attention is focused temporarily on a particular well producing petroleum from an idealized water-free solution-gas drive reservoir, the reservoir rock being a horizontal, thin, fairly homogeneous sandstone of large areal extent confined between two impermeable strata. The flowing hydrocarbon fluid is considered to exist entirely as a Iiquid at points in the reservoir remote from the well; however. the decline in fluid pressure in the direction of the well causes vaporization of the hydrocarbon to begin at a radial distance r from the well. Upstream from r the fluid moves entirely as a liquid and downstream from r it moves either entirely as a gas or as a gas-liquid mixture depending on the properties of the hydrocarbon and on the thermodynamic process it follows during flow. The distance r would be variable under transient flow conditions. but for purposes of analysis the flow is considered to l~e steady at the particular instant of observation during the flowing life of the well of interest. If the flow were isothermal and the hydrocarbon a pure substance, the fluid would be entirely gaseous downstream from r. Thus, this isothermal flow process for a pure substance would require that the heat of vaporization be supplied at r. over zero length of porous medium, at the precise rate necessary to maintain the constant temperature. This means that the solid matrix of the porous medium (reservoir rock) and the surroundings (impermeable strata confining the reservoir rock) would have to serve as infinite heat sources. Heat-transfer requirements would be somewhat less severe for the isothermal flow of a multicorn-ponent hydrocarbon as bubble and dew points at the same temperature correspond to different pressures. In this instance isothermal conditions would be sustained without complete vaporization of the fluid over zero length of porous medium. Nevertheless. as the flow is in the direction of decreasing

Jan 1, 1951

Frank 11. Probert, Neudorf, Anhalt, Germany (communication to the Secretary): I have read with much pleasure Mr. Collier's valuable paper. But the system of timbering which he describes as used in the levels, stopes, etc., though it must be admitted to be very strong and safe, seems to me somewhat extravagant. The amount of timber required every month for such a system must be enormous; and only where suitable material could be cheaply obtained would such a plan be economically practicable. The first point which strikes me is the unusually great diameter of the timber employed. In the mines of Pfaffenberg and Meiseberg, which are under my supervision, the country-rock consists of argillaceous slates, traversed by innumerable small fissures or joints, dipping at all angles and striking to all points of the compass. Undoubtedly, this net-work has been caused by the upheaval of granite masses in the vicinity. Each fissure is accompanied by a more or less well-c1efinc.d gouge or fluccan, caused by the rubbing together of the slates at or after the original disturbance. In such

Jan 1, 1900

By AIME

BORN in 1899, in Bridgeport, Conn., E. A. Anderson grew up in a center of the nonferrous metal industry. Perhaps that had something to do with his selection of mining as a career while an undergraduate in Yale. After securing his Ph.B. in mining he worked for a year at Handy & Harman. By this time physical metallurgy had supplanted his interest in mining and he entered the Yale graduate school where he secured his M.S. degree in metallography under C. H. Mathewson. After completing his graduate work he entered the employ of The New Jersey Zinc Co. in their research division where he has remained ever since. The transition from graduate study to industry involved no disruption of technical interests. Academic research relating to the zinc-aluminum alloys, then coming into use for die-casting, was followed by extensive and productive industrial research in the perfection and commercialization of these alloys. Research on rolled zinc and rolled zinc alloys, corrosion and stress corrosion, dry cells, electroplating on zinc, and electrodeposition of zinc followed in overlapping succession as time passed.

Jan 1, 1947

(This list. includes only those who have entered military service within the past month, or whose entry has only recently become known to us; it also includes a few names of those whose titles or assignments have been changed within the month. A complete list will he found in the Year Book mailed with this Bulletin. Another Honor Roll is maintained in the reception room of the Institute.) ALDEN, HERBERT W., Lieutenant-Colonel, Ordnance Dept. ALDER, ALFRED; Engineers' Reserve Corps. ALFORD, NEWELL G., Sergeant, Bureau of War Risk Insurance, Headquarters 84th Division. AMBLER, HARRY A., Lieutenant, 30th Infantry. ANDERSON, GEORGE K., JR., Sec. C, 1st Co.; 3d Officers' Training Camp. AYER, -FRANK A., 1st Lieutenant, 43d Squadron, 3d Prov. Regiment, Aviation Camp.

Jan 3, 1918

By Strathmore R. B. Cooke, Iwao Iwasaki

RECENTLY spectrophotometry has been reported to provide a convenient technique for the rapid and reproducible determination of xanthate concentration in pulp solutions,12 and for a kinetic study of xanthate decomposition in acid solutions." Since the application of this analytical technique is feasible for those compounds showing pronounced light absorption maxima in the near ultraviolet region, it was deemed advisable to investigate the absorption spectra of some of the organic compounds that are used in flotation. It is known empirically that certain groups of atoms in an organic compound cause characteristic light absorption in the ultraviolet and near ultraviolet range, and the wavelengths and intensities of the corresponding absorption maxima are relatively independent of the nature of the remainder of the compound. The characteristic values of such groups, which are known as chromophores, are given in the literature.4,5 According to this information, many of the sulphydryl compounds are expected to show absorption maxima in the near or long wavelength ultraviolet region, whereas the saturated fatty acids and the saturated alkylamines do not. This article reports the absorption spectra of the six following types of sulphydryl compounds; mono-, di-(xanthate), and trithiocarbonates, dithiocarba-mate, dithiophosphate (aerofloat), and mercaptan. A Beckman DU quartz spectrophotometer was used to investigate the spectra in the wavelength region of 215 to 350mp. Materials: All the mono-, di-, and trithiocarbonates used in this investigation were prepared in the usual manner" from appropriate compounds obtained from Eastman Distillation Product Industries. The dithiocarbonates included the normal alkyl compounds from methyl to octyl inclusive, as well as the isopropyl, isobutyl, and isoamyl xanthates. Iodo-metric titration gave 99.7 and 99.5 pct purity for

Jan 1, 1958

By James A. McGurty, Walter J. Koshuba, Samuel G. Gordon, Gilbert E. Klein

ONE of the problems encountered in working with metals at elevated temperatures is the instability resulting from solid-solid diffusion at a -common interface. A determination of the nature and magnitude of this phenomenon is important as related to structural properties of materials potentially useful in high temperature applications. This paper is concerned with the solid state reaction between metallic molybdenum and beryllium at elevated temperatures. In the older literature,' there were no known inter-metallic compounds in the system Be-Mo, and the list of beryllium intermetallics was rather small. New compilations have been made by Smithells' and by Taylor," listing all the then known beryllium binary intermetallic compounds. In addition to these, some new phases have just been reported' in the system Zr-Be and some further compounds of the type MBe,3 have been currently described. The new compound MoBe,, which is reported upon in this paper differs considerably from the above mentioned MBe13 group, and will be discussed in detail. Diffusion Study The nature of the solid diffusion at a Mo-Be interface was determined by sealing a beryllium rod inside a molybdenum capsule and heating at a temperature of 2000°F' (1100°C) for 100 hr. The molybdenum capsule was fabricated from % in. swaged molybdenum rod obtained from the Fansteel Metallurgical Corp. The beryllium metal was obtained from Brush Beryllium Corp. as % in. cold-drawn rod. This material assayed 99.05 pct Be and contained as impurities 0.84 pct Be0 and 0.19 pct Be2C. The molybdenum capsule was % in. in OD x 2 in. long. To prepare it, a concentric hole 0.250 in. + 0.001 in. — 0.000 in. in diam was drilled and reamed in one end of a rod to a depth of 1 '/2 in. A 1 in. long beryllium rod 0.250 in. + 0.000 in. — 0.001 in. in diam was pressed into the molybdenum capsule. A molybdenum plug 0.250 in. & 0.001 in. in diam x 9/16 in. long was then used to seal the beryllium in place. The capsules were placed in a molybdenum resistance furnace and heated at 2000°F (1100°C) for 100 hr. On cooling, the specimens were cut and examined metallographically. Fig. 1 is a micrograph at X250 of a portion of the interface from a transverse section. Four phases are clearly visible, with sharp boundaries between them. Phase A is a section of the molybdenum capsule; phase B is the molybdenum-rich intermetallic composition MoBe,; phase C is the beryllium-rich compound MoBe13; phase D is a section of the beryllium rod. All phases were readily polished to a high metallic luster. The molybdenum-rich phase has a pronounced purple tinge. The beryllium-rich phase (C) is only slightly darker than the pure beryllium. In polarized reflected light, however, it shows striking birefringence between crossed Nicols. The black areas represent flaws or pores in the material. A small representative amount of powdered material from each of the phases was carefully removed under the microscope with a diamond tool. With this material, powder X-ray diffraction patterns were made for the identification of each phase. Table I lists the X-ray diffraction spacings and corresponding indexes characteristic of these intermetallic compounds. Synthesis To establish the formula of the new intermetallic compound, X-ray diffraction patterns were made from powders obtained from solidified melts of known composition. The syntheses were made by

Jan 1, 1952

By B. B. Bucky

THIS investigation was carried on by means of models and the applica-tion of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimensions. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in- bed B, a 3/8-in, bed C and two 1/8 -in. beds D and E. The model was rotated at ±2350 r.p.m. equivalent to a model ratio of 1268. It was worked back 1/4 in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious ,reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft, and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel 1/8 in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1939

By I. N. Knapp

Introduction.—The spccial object of these notes is to describe the mixing, testing, and use of mud-ladened water for rotary drilling in such a way as to make them helpful to the driller, the operator, or the engineer in solving his own special drilling problems. The structures, apparatus and tools used are indicated in a general way. No attempt is made to describe the art of rotary drilling; only such descriptions as are necessary to make plain the use of mud are given. The information is the result of actual experience in drilling in Coastal Plain formations. The materials encountered in the wells drilled were unconsolidated sands, gravels, and clays, in which thin layers of sandstones, shell conglomerates, and shales began to appear at about 1,200 ft, in depth, although one well was drilled to 3,018 ft. without encountering any cemented or indurated materials. Unusual Conditions.—-The general surface of the ground where the drilling was done being hardly a foot above mean tide, and the daily tidal variation being about 15 in., it was found necessary to plank over the sod surface with 3-in. plank to work from. A 30 by 30 ft. planked area was sufficient to carry the derrick with equipment and 2,500 ft. of 4-in. drill pipe stacked in it. The derrick was set up 3 ft. on cribbed blocking arranged to spread the load over the planking. The engine, bailers, and pipe yard were also carried on 3-in. planking. Drilling 0utfit.—This consisted of a derrick, 20 by 20 ft. and 84 ft. high, two 35-h.p., "oil country" boilers, one double 8 1/4 by 10 in. reversible engine, two 10 by 6 by 12 in. duplex mud pumps, one 15-in. rotary, "hoisting works" with chain drive, hoisting block with line, crown block with pulleys, rotary jetting swivels, hose, complement of tools, pipes and connections, and a mud mixer, with engine. Hydraulic Rotary Drilling Method.—This method of drilling is an adaptation of Fauvelle'sl invention made in France in 1833 for drilling

Jan 1, 1915

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947

By H. R. Stahl

The ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classi- fiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9½-in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 52¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1¾ in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges

Jan 1, 1947