Search Documents

By K. E. Brown, A. R. Hagedorn

Continuous, two phase flow tests have been conducted during which four liquids of widely differing viscosities were produced by means of air-lift through 1%-in. tubing in a 1,500-ft. experimental well. The purpose of these tests was to determine the effect of liquid viscosity on two-phase flowing pressure gradients. The experimental test well was equipped with two gas-lift valves and four Maihak electronic pressure transmitters as well as instruments to accurately measure the liquid production, air injection rate, temperatures, and surface pressures. The tests were conducted for liquid flow rates ranging from 30 to 1,680 BID at gas-liquid ratios from 0 to 3,-270 scf/bbl. From these data, accurate pressure-depth traverses have been constructed for a wide range of test conditions. As a result of these tests, it is concluded that viscous effects are negligible for liquid viscosities less than 12 cp, but must be taken into account when the liquid viscosity is greater than this value. A correlation based on the method proposed by Poettmann and Carpenter and extended by Fan-cher and Brown has been developed for 1¼-in. tubing, which accounts for the effects of liquid viscosity where these effects are important. INTRODUCTION Numerous attempts have been made to determine the effect of viscosity in two-phase vertical flow. Previous attempts have all utilized laboratory experimeneal models of relatively short length. One of the initial investigators of viscous effects was Uren1 with later work being done by Moore et al.2,3 and more recently by Ros.4 However, the present investigation represents the fist attempt to study the influence of liquid viscosity on the pressure gradients occurring in two-phase vertical flow through a 1¼-in., 1,500 ft vertical tube. The approach of some authors has been to assume that all vertical two-phase flow occurs in a highly turbulent manner with the result that viscous effects are negligible. This has been a logical approach since most practical oil-well flow problems have liquid flow rates and gas-liquid ratios of such magnitudes that both phases will be in turbulent flow. It has also been noted, however, that in cases where this assumption has been made, serious discrepancies occur when the resulting correlation is applied to low production wells or wells producing very viscous crudes. Both conditions suggest that perhaps viscous effects may be the cause of these discrepancies. In the first case, the increased energy losses may be due to increased slippage between the gas and liquid phases as the liquid viscosity increases. This is contrary to what one might expect from Stokes law of friction,' but the same observations were made by ROS4 who attributed this behavior to the velocity distribution in the liquid as affected by the presence of the pipe wall. In the second case, the increased energy losses may be due to increased friction within the liquid itself as a result of the higher viscosities. The problem of determining the li- quid viscosity at which viscous effects becomes significant is a difficult one. Ros4 has indicated that liquid viscosity has no noticeable effect on the pressure gradient so long as it remains less than 6 cstk. Our tests have shown that viscous effects are practically negligible for liquid viscosities less than approximately 12 cp. Actually there is no single viscosity at which these effects become important. These effects are not only a function of the viscosities of the liquids and of the gas but are also a function of the velocities of the two phases. The velocities in turn are a function of the in situ gas-liquid ratio and liquid flow rate. Furthermore, the role of fluid viscosities in either slippage or friction losses will depend on the mechanism of flow of the gas and liquid, i.e., whether the flow is annular. as a mist, or as bubbles of gas through the liquid. These mechanisms are also a function of the in situ gas-liquid ratios and the flow rates. It would thus seem that the best one could hope for is to determine a transition region wherein the viscous effects may become significant for gas-liquid ratios and liquid production rates normally encountered in the field. The viscous effects might then be neglected for liquid viscosities less than those in the transition region but would have to be taken into account when higher viscosities are encountered. There are numerous instances where crude oils of high viscosity must be produced. The purpose of this study has been to evaluate the effects of liquid viscosities on twephase vertical flow by producing four liquids of widely differing viscosities through a 1 % -in. tube by means of air-lift. The approach used in this study was as follows:

Jan 1, 1965

By Charles E. Locke

The little stamp-mill in the mining laboratory of the Massachusetts Institute of Technology and the work done by it have been well described by Prof. R. H. Richards and E. E. Bugbee in a paper read at the Albany meeting of the American Institute of Mining Engineers, February, 1903.' As run for student class-work the mill contains a feeder, stamps, plate, and vanner. Results in the past indicate that the work of these machines is just as efficient as that of a regular mill handling the same class of ore. It has been the custom to obtain ore principally from Nova Scotia, mainly because it is the nearest source of supply, and also because there is a considerable saving in freight-cost as compared with other districts. The gold in Nova Scotia ores is notoriously coarse, and for this reason it is almost impossible to obtain satisfactory results by sampling and fire-assay, unless an extremely large lot of ore is crushed and all of the contained gold pellets are saved. A very interesting and most extraordinary example of this fact has been presented by a recent run in the Technology stamp-mill. Since the capacity of the mill is about 60 kg. per hr., and since in about 5-hr. run the students in any one section have an opportunity to make the necessary study of machines, it usually happens that several runs are made from one lot of ore. When the shipment is received it is first dried and weighed, put through the Blake breaker, set at 1 or 1.5 in., and the crushed product is piled in a cone on the sampling-floor. When the crushing is completed the ore is usually stored away in barrels for future use; it is aimed to have each barrel of

Jan 1, 1914

By F. V. Lenel, G. S. Ansell, M. J. Salkind

An experiment is described in which the growth of interparticle necks in an array of loose spherical silver powder at temperatures near 300°C was determined by measuring changes in the electrical resistance of the array. The activation energy for neck growth of contacts was derived by abruptly changing temperature and noting the change in the rate of neck growth. Since the experiments were run under an external load, the changes in activation energy with stress could he determined. The activation energy was found to decrease rapidly with increasing stress. It is concluded that the material transport in the experiments is one of plastic flow by dislocation motion. The variation of activation energy with stress is typical for cross slip of dislocations, an important material transport mechanism in the temperature range investigated. THE process in which powder compacts or aggregates of loose powder are held at an elevated temperature under an external load is called hot pressing or sintering under pressure by powder metallurgists. In this investigation the early stages of this process as applied to loose spherical silver- powder aggregates were studied. The powder particles were approximately 100µ in diameter and the temperature was near 300°C, i.e., below one half of the melting point of silver in degrees Kelvin, where volume diffusion is not expected to contribute to sintering. In the process, the contact or neck areas between powder particles grow. Since this involves plastic deformation of the particles under a constant external load (even though not under constant stress) it would be termed creep by mechanical metallurgists. On the other hand, the growth in neck area observed in compacts or loose-powder aggregates held at elevated temperature without the application of an external load is termed sintering by powder metallurgists. During sintering the major driving force is the stress due to surface tension. However, even when no load is placed on the compact or powder aggregate, an external stress, i.e., gravity, plays an important role in sintering in addition to those stresses arising from surface tension, as was shown in two previous investigations.'" It is therefore postulated that no sharp dividing line can be drawn between the phenomena of "creep" and "sintering". Different material transport mechanisms may be involved in either of these phenomena, but they will depend upon the temperature and the level of stress, but not necessarily upon the nature of the driving force: surface tension or external load. At the low temperatures of this investigation, an external stress much higher than the stress due to surface tension is necessary to obtain measurable rates of neck growth. In order to avoid misunderstanding this phenomenon will be called "creep". The rate of growth in contact area in the loose silver-powder aggregates was determined by meas-

Jan 1, 1965

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author's reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond's statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By Bunting S. Crocker

DISCUSSION Fred C. Bond (Allis-Chalmers Manufacturing Co., Milwaukee)—This is a very complete description of the screened ore fine grinding installation at Lake Shore. The only important data which might be desired are the operating screen analyses and power consumption in each stage. The statement that the energy consumption, or kw-hr per ton, remains constant for all mill diameters is of great interest, but the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases. More definite test work is needed to establish this point. Screened ore fine minding has been successful on hard Lake Shore ore &d on about equally hard South African Rand ore. However, it is still not determined whether it would be successful on ores of average or less than average hardness. It is possible that with softer ores the consumption of ore pebbles might be exceedingly high, or might even exceed the available supply. Also, the softer feed might result in a rapid buildup of harmful intermediate sizes in the mill circuit. These factors can be determined only by a full scale or long pilot mill test. In any case the Lake Shore staff is to be congratulated for this pioneering work. Bunting. S. Crocker (author's reply)—As requested, the operating screen analyses and Bower consumption for each of the four stages of pebble milling are given, see Table XII. The fist three stages are in series circuit; the last stage is in closed circuit. The primary circuit had rock feed averaging 124 g per piece and the final stages rock feed weighing 63 g. The intermediate stages had mixtures of the two. Regarding Mr. Bond's statement that "the opinion is widely held that the kw-hr per ton decreases as the mill diameter increases," I would say that I have frequently been told this but have never yet been shown any evidence or seen any evidence published that would prove this statement. It may be true that some of the big mills recently installed have mechanical power savers such as micarta bearings and better lubrication, but as far as the power consumed inside the mill is concerned, we at Lake Shore think that it varies as D2 .", and that is all. We published extensive information on this point in our 1939 paper. Recently Mr. Banks at Consolidated published the figures on his 10 ft 8 in. x 12 ft 0 in. rod mill. As reported in this discussion by the writer: we calculated the power necessary to run this mill based on our 7x6-ft rod mill to within 1 pct of the actual power reported by Mr.

Jan 1, 1953

By Samuel E. Doak

The utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose, loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 11/2 per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In modern practice the percentage of sulphur in the cinder is rarely as great as six, and seldom lower than one and one-half. Average analyses for iron, silica, and sulphur of the cinders that have come under my personal observation are as follows:

Jan 1, 1916

THE annual winter meeting of the A.I.M.E., which is to open in New York on Feb. 14, will be charac-terized by a number of novel features. The most important is that the technical sessions will be dis-tributed over four days instead of three as heretofore. This makes it possible to reduce the number of conflicts between sessions and also will enable each member to attend a larger number. At the same time the ses-sions are so arranged by groups that those interested only in one or more that are related can, if necessary, cover all in that group in three days as heretofore. The general excursion to which the fourth day has, for some years, been devoted has been regretfully given up, mainly because of the uncertainties of the weather in New York in February. In its place a series of group excursions are being offered at various times during the meeting, arranged, so far as possible, so as not to con-flict with any technical session likely to be of interest to those taking part in a particular excursion. Among the places to be shown the visitors are: the construction work on the Eighth Avenue subway, a real mining job; the Vehicular Tunnel, the world's greatest ventilating project; the manufacture of 42-in. conveying belts; one of the largest and most modern steam plants; a coal terminal; manufacture of mining equipment; a cable-making plant; an oil terminal and refinery. Other en-tertainment features include a smoker Monday evening with a real chance to get together and talk; an informal dance and entertainment given by the Woman's Auxiliary on Tuesday evening; the dinner-dance at the Waldorf Wednesday evening, with no long speeches; a general session Thursday evening when the Petroleum Division will present a series of important reviews of the year. An extensive program has been arranged for enter-taining the ladies, and members are urged to bring their wives. There will be dinners, teas, theater parties, shopping and sight-seeing excursions as well as the dances. The usual general luncheons for members, guests and ladies will be served each day at headquar-ters, and various committees and groups will hold lunch-eons, dinners, and round table conferences as indicated in the schedule on the page opposite. The Mining and Metallurgical Society of America and the American Society of Steel Treaters are participat-ing in this meeting and their members will be welcome as guests at any session or function. A joint conference of the Mining and Metallurgical Society and the A.I.M.E. has been arranged for Tuesday afternoon, under the chairmanship of Clinton H. Crane, at which the whole matter of the mineral reserves of this country is to be up for discussion.

Jan 2, 1927

By R. A. Pallanch

PROBABLY one of the most perplexing problems with which a mill operator contends is the proper evaluation of his mill results. True, he accurately determines his recoveries of metals and grades of products monthly, weekly, and often daily. These figures do not of themselves directly translate to mill economics. When one figure is unusually good there may be an offsetting circumstance. The advantage of high lead or zinc concentrate grade may be offset by poorer recovery; high lead recovery may be offset by poorer zinc recovery, or vice versa; and so on. Besides, grades or recoveries may not of themselves mean more than a reflection of the grade and character of the ore during the period under study. What the operator sorely needs is some one measuring stick that tells him when he has achieved his greatest return, regardless of grades or recoveries-for if he knows his methods and practices are yielding the optimum return he need no longer concern himself with the assays of products and tailings, or the corresponding distribution of metal values. At first blush it would appear that the obvious answer to this is the actual money return to the mill. Paradoxical as it may seem, however, money return does not make a dependable yardstick any more than do grades and recoveries, as ore conditions would vary enough to bring about greater money return during periods when the actual metallurgical work is not as good. The mill operator, of course, should always aim for the greatest return on the ore, once it is in the mill bins, with proper attention always to mill treatment cost. The need of a proper yardstick becomes more imperative with the increasing complexity of the problem. In the case of a simple, single-product operation on a fairly uniform ore, in which only one metal is of significant importance, the need is not great, as grade and recovery pretty well tell their own story. At the other extreme is the operation that makes three or four separate marketable products from a complex mixture of heterogeneous ores that vary tremendously in individual metal contents and ratios, degree of oxidation, and other characteristics, and in which gold, silver, copper, lead and zinc are all significant values. ECONOMIC RECOVERY The first attempt at obtaining a proper single yardstick for a fairly complex ore with which I am familiar is the use of the "Economic Recovery" term at the leadzinc flotation mill of the Sunnyside Mining and Milling Co., Eureka, Colorado. This method had been applied there early in Sunnyside flotation-mill history (not later than 1920) and credit for the innovation I believe belongs to Messrs. Kuryla and Marquand. The term "Economic Re-

Jan 1, 1947

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,' through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969

By Herbert Haas

1. INTRODUCTION COPPER matte is now converted into blister copper at a cost of only $5 per ton of copper, or, based on a 40 per cent. matte, $2 per ton of matte, which is the record of at least one large smelting Works; and it seems hardly likely that a further reduction, large enough to warrant, a change in existing practice, could be made in bessemerizing costs. But the new type of converter here described and the new practice proposed are intended, not so much for the treatment of mattes, as for the extension of, the process to the direct reduction in the copper-converter of pyrite ores

Jan 6, 1914

By Thomas T. Read

MINING, which is at least twenty centuries old, was at first, and long, wholly a practical art. Little more than two centuries have elapsed since the inception of the idea that general education and a knowledge of natural science would be of advantage to those engaged in the mining industry. Though schools of mining began to develop in Europe early in the eighteenth century the concept of educational preparation for technical conduct of the industry was slow in winning general acceptance in the industry itself. John Hays Hammond, in his autobiography,1 recalls that when he sought employment with a mining company after he had graduated from Yale and Freiberg he had to assure its executive, before being even considered for employment, that he did not consider that he had learned anything about mining. This was as late as 1880. Existence in the industry of a prejudice against education of the academic type is perhaps an explanation why inadequate provision has been made by the mining industry for the continuing education of technical employees after they enter employment, although engineering education prior to engaging in industry has now won general acceptance. I am familiar with the existence of "loop" courses for engineering graduates in metallurgical plants, of schemes for giving mining graduates "practical experience," and of the interest in vocational courses for workmen which sprang up in the period of labor shortage during and immediately following World War I (but which quickly died when the depression of 1921 again made experienced workmen available in sufficient supply), having been chairman of a committee appointed by the Mineral Industry Education Division to make a survey of existing provisions for post-employment training for engineers in our industry. The results of that survey, reported elsewhere, clearly indicate that it is inadequate as to amount; the aim of this paper is to present evidence for belief that it is also inadequate in quality. To avoid becoming too involved, no reference will be made here to post-employment vocational training for workmen, which is a subject differing so much from post-employment education for engineers as to require separate treatment. Neither will postgraduate education for metallurgical engineers be discussed, because a distinction must then be made between training for research work and for plant operation, whereas mining engineers engage almost exclusively in operations. Since the situation in the coal-mining industry has been discussed at several recent meetings, that also will be passed over, and what follows should be taken as a discussion applying exclusively to the metal-mining industry. PROFESSIONAL DEVELOPMENT In the operations field (both in mining and metallurgy) the work to which a beginner is assigned is seldom closely related to previous academic education. The contrast is almost as great as between

Jan 1, 1941

By F. C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of transporting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion. FIXED-SOURCE METHODS Essentially, a fixed-source method consists of the measurement of electromagnetic fields about the source. The mutual coupling between the source and the earth is constant, but the mutual coupling between the receiver and the earth (unless the earth is homogeneous) and also between the source and the receiver changes at each station. The results are usually normalized by relating the field data to the calculated free space or primary field. Turam and Radio Reference Signal Methods: The turam or two-frame* (see Fig. 1A) is probably * Turam means two-coil. the most common fixed-source method. The energizing source is an insulated cable grounded at both ends or formed into a large rectangular loop. Measurements are taken along a traverse at 5 to 50-meter intervals using two small receiving coils, the lagging coil being placed at the position previously occupied by the leading coil. The complex ratio (i.e., inphase and out-of-phase ratios) of the voltages induced in the two coils is measured. Operating frequency range is about 100 to 800 cps. In a typical turam survey a straight, grounded cable several kilometers long is laid out parallel to the probable strike of the ore deposits or conducting strata being sought. An area extending 1 or 2 km on each side of the cable, and within 1 or 2 km of the ends of the cable, is surveyed. Measurements are made at stations 5 to 25 m apart along traverses perpendicular to the cable. Measurements may be made along lines parallel to the cable to serve as base lines for the traverses or for other special purposes. Commonly the receiving coils are oriented with their planes horizontal so that only the vertical component of the field is measured. If additional information is required, one of the hori- zontal components may also be measured by orienting the coils with their planes vertical. In a modified turam technique developed recently for both ground and airborne measurements (Fig. 1B) the amplitude of the complex voltage induced in a single receiving coil is measured and its phase compared with that of a reference signal transmitted from the energizing system by a radio frequency carrier. Thus the un-normalized field is obtained directly, whereas with the turam method it is obtained by calculation from the ratios. The turam method and its modifications have a greater working depth than the other electromagnetic procedures used in ore prospecting. Under favorable conditions conductors have been located at depths of 200 to 300 m. A modified turam method with one of the electrodes grounded in the upper end of a plunging orebody was used to follow the extension of this body to a depth of 200 m beneath a layer of conducting schists. Straight grounded cables are usually preferred to insulated loops because they are easier to lay out and because they often make the method more sensitive. The greater sensitivity of a grounded cable is a result of ground return currents which may flow in the orebodies in addition to the eddy currents caused by induction from the current in the cable. Anomalies in the vertical field due to eddy currents are characterized by a correspondence between high values for the inphase component and positive out-of-phase components and/or low values for the inphase component and negative out-of-phase components. Also the inphase component may approach zero, but it does not become negative. In very long continuous conductors that are parallel to a grounded cable the effect of ground return currents may far exceed the effect of eddy currents. These ground return currents cause a lack of correspondence between the inphase and out-of-phase components and may cause negative inphase or anti-phase components. It becomes difficult to carry out the measurements and often difficult to interpret the results. Such results immediately suggest the presence of graphitic strata, however, since ore deposits are rarely extensive enough to accumulate sufficient ground return current to cause these results. A cable laid out perpendicular to the strike or an insulated loop is sometimes used in areas where graphitic schists and slates are present. Anomalies are then completely or almost entirely due to eddy currents and are easier to interpret. The measured voltage ratios are normalized by either subtracting or dividing by normal field ratios calculated from free space considerations. The normalized ratios are then plotted as individual profiles. When significant anomalies occur in the ratio measurements, the actual normalized fields are calculated by beginning with a measured or an assumed value for the field at a point near the cable and successively multiplying this value by the normalized ratios. There is a similarity between this process and a numerical integration of the ratio curve. Conversely, in many respects the ratio curve is similar to the first derivative of the field curve.

Jan 1, 1960

Department of Forestry and Geological Development, 435 State Capitol, Atlanta, Ga. S W. McCalhe, State Geologist. A complete list of Bulletins of the Geological Survey of Georgia will be sent upon request. Forty-five Bulletins have been issued, most of which deal with the mineral deposits of the state and are still available; they may be had on payment of postage. The subject matter of those bulletins of most interest is indicated in the following list, with the year of issue and the mailing weight. Bulletin 1, Marbles (1894), 3 lb , 8, Road building materials (1901), 3 lb , 9, Granites and gneisses (1902), 2 lb ; 10, Iron ores (1900), 2 lb , 11, Bauxite (1904), 2 lb.; 12, Coal deposits (1904), 2 lb ; 13, Ocher deposits (1906), 2 lb.; 14, Manganese deposits (1908), 2 lb ; 17, Fossil iron ore (1908), 2 lb.; 18, Clay deposits

Jan 1, 1933

By Alan E. Gallie

SHERRITT Gordon Co. was formed in 1927 to exploit a copper zinc orebody located in the bush 90 miles north of The Pas, Manitoba. The mine went into production in 1931, operated for a year and a half, and closed because of the low price of copper. Reopened in 1937, it operated continuously until mined out in 1951, producing 8.5 million tons of ore. From 1937 on Sherritt Gordon conducted an energetic prospecting program throughout northern Manitoba, giving particular attention to the belt of favorable greenstone rocks north of the Churchill River. From 1937 to 1941 a number of gold showings were located but nothing of economic value was found.

Jan 3, 1957

By M. D. Scott

A second generation tailings system, consisting of 8 km (5 mile) of large diameter 914- mm (36-in.) po1yethylene pipeline, the bulk of which was laid on a 0.2% grade, has been successfully operated by Lornex Mining Corp. for the past 2 yr. The system was designed to operate as a partial flow pipeline during average flows with the ability to pressurize itself and operate as a pressure pipeline under high flows, or clean itself out under sanding conditions. The system has exceeded design capacity and has had very little downtime. Polyethylene pipe was easily and inexpensively installed and has exhibited superior abrasion resistance characteristics.

Jan 1, 1978

Iowa Geological Survey, Des Momes, Ia. George F. Kay, State Geologist A list of publications will be sent upon request Most of the papers of the Survey have been published in the Annual Reports, issued since 1892. Separates of the many papers in the Reports may be had for postage, except where they are out of print, and except for vol 1 (1892), 2 (1894) and 14 (1903), where no separates are to be had. Thirty-five Annual Reports have been issued up to and including vol 35 (1929). A charge, plus postage, is made for vols, 4, 5, 7, 8, 9, 10, 28 and 33, others will be sent free upon request, plus postage on from 2 to 6 pounds Space prohibits giving more than a general picture of some of the contents; vols 4, 5, 7, 8, 9, 10, 11, 12, 13, 15, 16, 20, 27, 32, contain, among others, papers on the geology of Iowa, by counties Vol. 19 (1908), 6 lb , contains a number of papers dealing with the peats and coals of Iowa, and has bibliographies of those subjects Vol 22 (1912), 6 lb , contains an annotated bibliography of Iowa geology Vol-24 (1913), 6 lb , contains the analyses of 16 Iowa coals Vol 28 (1917, 1918), price $1 50, 4 lb , completely covers the subject of gypsum in Iowa, and has a bibliography of the sub¬ject. Each volume carries an administrative report and a review of mineral production for the period covered In addition, Technical Paper 2 (1930), Studies of Iowa coals, will be sent free upon request Also a geological map of Iowa, and maps of Iowa showing the distribution of the glacial drift sheets throughout the state, have been issued and are available

Jan 1, 1933

By W. I. Duvall, D. E. Stephenson. Discussion by R. G. K. Morrison

R.G.K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que. Canada) - The authors have introduced a subject, the intensive study of which has awaited scientific developments. These are now such as to justify a thorough review of our thinking on the causes and control of rockbursts. The formulae developed in the paper, the comparison between rockbursts and earthquakes in figure 1 and the energy data relating to explosives serve as an effective foundation. In the paper this writer is quoted as suggesting that energy of the order of 10 x 10 11 ft. lb. may have been released in some of the heaviest rockbursts in the Kolar Gold Field. He now hastens to add that such an estimate has no scientific validity. It arises only from a casual comparison of surface and underground effects of the medium heavy bursts, referred to in the paper and estimated by Jones at 3.0 x 1010 ft.lbs., with those of obviously greater magnitude. In any case, we have the estimate by Jones above, that by a team of seismologists 1 on the Witwatersrand of 10 x 1010 ft.lbs., that by Coates of 3.8 x 10" ft.lbs., also referred to in the paper, that by Blan-chard2 for the catastrophic rockburst at Springhill, N.S., of only 7.4 X 107 ft. lbs., and finally the range covered by Cook, referred to in the paper. It is probable also that data for the heavy rockburst at Merkers3 in the WERRA potash area of Germany are available as it was recorded on seismographs from Moscow to Spain. It is the writer's impression that some standardization is present in the estimates above for 10 x 10 10, 3.8 x 1010 and 7.4 x 107 ft.lbs., respectively. The latter, for Springhill, represents a relatively low order of magnitude. It is obvious that any energy estimate must be related to the local geometry of openings at the time of the event. It is also obvious that any explanation of the causes of rockburst must be capable of providing a wide range of energy. However, we must remember that the energy release is an effect indicating magnitude. The cause lies with the mechanism initiating the primary failure, generating the seismic activity, to which much of the damage is probably due.

Jan 1, 1967

By Thomas T. Read

MINING, which is at least twenty centuries old, was at first, and long, wholly a practical art. Little more than two centuries have elapsed since the inception of the idea that general education and a knowledge of natural science would be of advantage to those engaged in the mining industry. Though schools of mining began to develop in Europe early in the eighteenth century the concept of educational preparation for technical conduct of the industry was slow in winning general acceptance in the industry itself. John Hays Hammond, in his autobiography, recalls that when he sought employment with a mining company after he had graduated from Yale and Freiberg he had to assure its executive, before being even considered for employment, that he did not consider that he had learned anything about mining. This was as late as 1880. Existence in the industry of a prejudice against education of the academic type is perhaps an explanation why inadequate provision has been made by the mining industry for the continuing education of technical employees after they enter employment, although engineering education prior to engaging in industry has now won general acceptance. I am familiar with the existence of "loop" courses for engineering graduates in metallurgical plants, of schemes for giving mining graduates "practical experience," and of the interest in vocational courses for workmen which sprang up in the period of labor shortage during and immediately following World War I (but which quickly died when the depression of 1921 again made experienced workmen available in sufficient supply), having been chairman of a committee appointed by the Mineral Industry Education Division to make a survey of existing provisions for post-employment training for engineers in our industry. The results of that survey, reported elsewhere, dearly indicate that it is inadequate as to amount; the aim of this paper is to present evidence for belief that it is also inadequate in quality. To avoid becoming too involved, no reference will be made here to post-employment vocational training for workmen, which is a subject differing so much from post-employment education for engineers as to require separate treatment. Neither will postgraduate education for metallurgical engineers be discussed, because a distinction must then be made between training for research work and for plant operation, whereas mining engineers engage almost exclusively in operations. Since the situation in the coal-mining industry has been discussed at several recent meetings, that also will be passed over, and what follows should be taken as a discussion applying exclusively to the metal-mining industry. PROFESSIONAL DEVELOPMENT In the operations field (both in mining and metallurgy) the work to which a beginner is assigned is seldom closely related to previous academic- education. The contrast is almost as great as between

Jan 1, 1941

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received little study on the part of wire mills, particularly those that have commenced operations in the last few years. Two Types of Defects One type of defect is generally known in this country as "check marks;" in Europe it is termed "crowfeet" (Fig. 1). This defect occurs in the surface of the copper wire, in the form of V's, which are always

Jan 1, 1930

By S. J. Hruska, G. M. Pound

The critical supersaturations for appreciable nucleation rate of cadmium crystals on copper and glass substrates at 186°Kwere measured as a junction of thermal-beam energy over a range of source temperatures between 616" and 839OK. There was no effect of source temperature on critical super saturation. This implies that the adsmbate prior to nucleation is in thermal equilibrium with the substrate. THE deposition of metallic vapors on solid substrates has been found to exhibit a critical behavior in that the rate of formation of deposit increases markedly when the intensity of the vapor source is increased slightly.* Evidence of the ability of sub- where Je is the flux which would arrive if the substrate were equilibrated with bulk condensate at the adsorbate temperature. The following work was undertaken to test this hypothesis. A) Energy Exchange Between Metallic Vapor and Substrates. When a freely translating atom collides with a stationary solid body its energy and momentum undergo changes which determine whether the atom is reflected or adsorbed. An atom is considered to be reflected if it returns to a freely translating state after remaining under the influence of the body for only a time comparable to the period of oscillation of atoms on the surface. An atom which remains for a longer time is said to be in an adsorbed state. The parameter which describes the energy transfer occurring at the interface is the thermal-accommodation coefficient which may be defined in terms of energy as Ei = average energy of impingent atoms, Eeq = average energy of an emergent atom which has equilibrated with the substrate, and Eem = average energy of an emergent atom. If a temperature is assigned to each of these energies, we have at as defined by Knudsen.2 Since this allows no distinction between reflected and evaporated atoms, a more specific definition is introduced for the present purposes, namely 71 = probability that an impingent atom is transferred to an adsorbed state, aj = thermal-accommodation coefficient for reflected atoms, and aTc = thermal-accommodation coefficient for adsorbed atoms. During a time t,, the mean stay time, prior to evaporation the adsorbed atom (adatom) will interact with the substrate and this will have the net effect of transferring the adatom towards a state of

Jan 1, 1964