Search Documents

By D. E. Moore

The strength of a natural serpentinite gouge was measured at 400°C and an effective pressure of 100 MPa. The strength of the gouge decreased with increasing pore pressure to 50 MPa and then was nearly constant between 50 and 125 MPa. The samples at 50-125 MPa pore pressure slid stably, whereas those at 3-25 MPa pore pressure showed stick-slip behavior. Lengthening the pre-heating time to 72,000 s of samples at 100 MPa pore pressure led to increases in both the strength and the likelihood of sliding unstably. With still longer pre-heating times, the strengths decreased again and sliding once more became stable. The strength of the gouge at 3 MPa pore pressure was unaffected by changes in pre-heating time. A possible explanation for the results is that excess pore pressures are being generated in the gouge, causing the true effective pressure to be lower than the apparent value.

Jan 1, 1984

By Bernard MacDonald

The writing of this paper was prompted by the discussion by H. M. Chance of the paper written by Thomas M. Chance,l and by the remarks of the editor in which he stated that while the matter contained in discussion did not refer to the original paper it " was presented as of interest to the operators of cyanide and other lixiviation processes dealing with fluid mixtures of varying specific gravity." For some years past the principle enunciated in the discussion referred to has been known to the writer and demonstrated by him to be an efficient and economical way of separating water or solution from solids in the cyanidation, lixiviation or acid leaching of ore pulps. In utilizing this principle in commercial practice he has invented a method whereby not only the separation of solution from solids may be effected in any given tank, but also the counter migration of the solids and solution may be effected continuously through a series of tanks in which the hydro-metallurgical treatment of ore pulps is being carried on. In effect this method is analogous to the counter-current system, but is different physically in that it is carried on throughout a series of tanks on practically the same level, continuously and automatically, by hydrostatic pressure and gravity-flow, without the aid of intervening pumps or elevators, at the same time that agitation is being carried on in the same tanks. In the Parral system, agitation is effected in tanks by a number of air lifts of comparatively small diameter through which the pulp is continuously transferred from the bottom of the tank and spouted horizontally on top of the charge. The spouting force of the several streams thus discharged maintains a rotary flow in the pulp charge which extends from top to bottom of the tank. This continuous transfer of pulp and the spiral flow from top to bottom of the tank maintains the pulp constituents in uniform proportions and meets the requirements of efficient treatment in a most economical manner. The quantity of compressed air required is very small, as the pulp is not lifted but simply transferred from the bottom to the top of the tank charge under hydrostatic balance. Fig. 1 gives a bird's-eye view of two adjoining tanks in any series equipped with the apparatus for producing the separation of

Jan 1, 1919

By A. S. Keh, H. A. Wriedt

The Precipitation of nitrides in quenched Fe-N alloys, aged between 25° and 200°C, was studied by transmission electron microscopy. Different dislocation substructures were introduced into the materials by recrystallization, cold working, and by Phase transformation prior to the introduction of nitrogen. It was found that the precipitated nitrides, tentatively identified as Fe16N2, have (100) habit planes. Nucleation takes place Preferentially at dislocations and at subboundaries. It sometimes occurs in the matrix, probably on vacancy clusters, but rarely on high-angle boundaries. The process of nucleation on dislocations and subboundaries is very temperature dependent. At room temperature there is no particular orientation relationship between the dislocations involved and the (100) planes on which the nitride Particles formed. With increasing temperature, the nucleation sites tend to become restricted to those dislocation segments lying in (100) planes. The change of yield stress of the 0.022 and 0.043 pet N alloys during quench aging can be correlated semiquantitatively with the change in particle distribution. Strain aging in quenched alloys can be separated into two stages. The early stage is attributed to nitrogen segregation to dislocations and the later stage is associated with precipitation. When previously quench-aged specimens were strained and aged, no additional Precipitates could be seen, although a considerable amount of strain aging occurred. DURING the past two decades, the precipitation of nitrides from a iron has been extensively studied by various techniques. It has been established that two types of nitride exist. The stable nitride, Fe4N, forms at temperatures above 250oC and Fe16N2, the

Jan 1, 1962

By R. W. Raymond

Most of US, in this hurrying age, take little pains to preserve such records of our doings as will make the work of' our biographers easy. Now and then there is an exception, and Dr. Trippel was one. Methodical in all his habits, he kept diaries and journals comprising his own personal experiences, the details and results of his numerous scientific investigations, and his impressions concerning men and events; and also copies of all his technical essays, published by various societies or periodicals. It is a striking instance of " the irony of fate," that these carefully-preserved materials, which would now have a real historical, as well as biographical value, were totally destroyed by an accidental fire a few years ago. In addition to my own recollections of an acquaintance covering more than thirty years, I am indebted, for the fads upon which this sketch is based, chiefly to Mr. Engene J. Trippel, a son of the deceased, and now Register of the United States Land Office at Tucson, Arizona. Mr. Trippel, however, frankly confesses that his own knowledge of his father's work is, in the absence of written records, imperfect.

Jan 1, 1898

By Molly Gleiser

The standard free energies of formation of some gaseous metal oxides together with those of their condensed oxides have been plotted against temperature. The heats of formation of the gaseozcs oxides are tabulated. An explanation is given of the use of the data to predict the importance of the gaseous metal oxides at high tenzperatures. RECENT mass spectrometric work1 has resulted in the detection of several hitherto unknown gaseous oxides and the measurement of their free energies of formation. Of especial interest is the fact that several of the refractories in common use either as crucibles or furnace tubes, and metals used in Knudsen cells and in furnace windings, have been found to have one or more stable gaseous oxides. In view of the present emphasis on high-temperature techniques, the development of vacuum metallurgy.z heating by electron bombardment and plasma jets, and the resultant shift to ever higher temperatures, it is no longer possible to plan experiments without taking into consideration the significance of the presence of these gases in the system, the reactions they undergo. and their contribution to the vapor pressure. A good example of what went wrong in earlier work, when the existence of these gaseous molecules was not yet known, is presented by the work of Hoch, Nakata, and Johnston. Hoch and coworkers attempted to measure the vapor pressure of solid ZrO2 by letting the vapor in equilibrium with zir-conia effuse from a tantalum Knudsen cell. The free energies of formation of solid zirconia and tantala are such that a short calculation showed that the reaction

Jan 1, 1962

By James R. Dunn

The purpose of this chapter is to review the uses of sand and gravel by the construction industry. The specific intention is to give tech¬nical people the general perspective and frame¬work which they need to help in making tech¬nical and business decisions. In the sand and gravel industry such decisions are based on an understanding of sociologic, economic, and technologic factors. In order to discuss the sand and gravel industry intelligently, it is necessary to define sand and gravel. "Sand" as most often used by industry is not sand in an engineering or geo¬logic sense but should be called "natural fine aggregate." The expression "fine aggregate" is preferable to "sand" because fine aggregate in¬cludes grain sizes which, according to engineer¬ing or geologic classifications, are defined as pebble or grit size. Natural fine aggregate is distinguished from manufactured fine aggregate in that the manufactured material is crushed and screened to produce the required sizes and natural fine aggregate is only screened. Coarse aggregate is generally defined as aggregate which will not pass a No. 4 or %o-in. sieve. Coarse aggregate may be natural (gravel) or manufactured (crushed stone, crushed gravel, slag, or coarse lightweight aggregate). Gravel is usually considered sufficiently crushed to qualify as manufactured coarse aggregate when two or more sides are broken. Sand and gravel (crushed or uncrushed) is used in asphaltic and portland cement concretes, is subbase for pavements, as fill where good drainage is needed (such as around structures), and for many other uses. About 96% of all he sand and gravel produced is used in construction.

Jan 1, 1975

By S. P. Kinney

Sulfur has been one of the most troublesome elements encountered since the earliest days of iron smelting, and this problem will become of increasing importance as the higher sulfur coke is used, because of the rapidly diminishing supply of low-sulfur coals suitable for the manufacture of metallurgical coke. The deleterious effect of sulfur in iron and steel is well known; therefore, except in special cases, it is desirable to make the iron produced by the blast furnace as low in sulfur as possible. Sulfur enters the furnace in all of the raw materials, but principally in the coke. It comes out of the blast furnace distributed between the iron and the slag; very little passes out of the furnace with the gases. The mechanism of the reactions that cause the sulfur of the coke to pass into the slag and iron has not been studied to any great extent, although the character of the end products, and the conditions controlling the distribution of the sulfur between the iron and slag, are fairly well known. In the iron, the sulfur occurs as ferrous sulfide; or manganese sulfide in case of iron high in manganese. In the slag, the sulfur is present mostly as calcium sulfide. The presence of free sulfur1 and sulfates in blast-furnace slags is to be accounted for on the basis of oxidation of the calcium sulfide after the slag is tapped. The generally accepted reaction for the relation between the ferrous sulfide in the iron and in the coke, and the calcium sulfide in the slag, is that given by Howe? FeS + CaO + CDFe + CaS + CO

Jan 1, 1923

By S. P. Kinney

Sulfur has been one of the most troublesome elements encountered since the earliest days of iron smelting, and this problem will become of increasing importance as the higher sulfur coke is used, because of the rapidly diminishing supply of low-sulfur coals suitable for the manufacture of metallurgical coke. The deleterious effect of sulfur in iron and steel is well known; therefore, except in special cases, it is desirable to make the iron produced by the blast furnace as low in sulfur as possible. Sulfur enters the furnace in all of the raw materials, but principally in the coke. It comes out of the blast furnace distributed between the iron and the slag; very little passes out of the furnace with the gases. The mechanism of the reactions that cause the sulfur of the coke to pass into the slag and iron has not been studied to any great extent, although the character of the end products, and the conditions controlling the distribution of the sulfur between the iron and slag, are fairly well known. In the iron, the sulfur occurs as ferrous sulfide; or manganese sulfide in case of iron high in manganese. In the slag, the sulfur is present mostly as calcium sulfide. The presence of free sulfur1 and sulfates in blast-furnace slags is to be accounted for on the basis of oxidation of the calcium sulfide after the slag is tapped. The generally accepted reaction for the relation between the ferrous sulfide in the iron and in the coke, and the calcium sulfide in the slag, is that given by Howe? FeS + CaO + CDFe + CaS + CO

Jan 1, 1923

By Joseph F. Oesterele, Richard S. McCaffery

This investigation was undertaken to determine the quality of different iron blast-furnace slags as desulfurizing agents, and the possibility of using, in the blast furnace, materials of higher sulfur content than is now common. The solution of the problem would render possible the use of higher sulfur iron ores for pig iron and cokes containing more sulfur than now employed, and the economic manufacture of irons and steels of lower sulfur content. It is generally assumed that the sulfur that reaches the lower part of the iron blast furnace is removed from the pig iron by combining with lime to form calcium sulfide. Most of the sulfur introduced with the charge is in combination with iron or manganese or, perhaps in the coke, as a carbon compound.1 The iron and manganese sulfides are more soluble in the iron than is calcium sulfide, and as the latter is generally said to to be more soluble in the slag than the iron and manganese sulfides, this greater solubility of calcium sulfide in the slag tends to free the metal from sulfur. This greater solubility of the calcium sulfide is used not only to reduce the sulfur contents of the pig iron in the blast furnace, but by this means also low-sulfur steels are produced in the open-hearth and electric furnaces. The reaction2 FeS + CaO + CO = Fe + CaS + CO2 requires a high temperature and strongly reducing conditions in the presence of lime. The constitution of blast-furnace slags, first studied scientifically by Vogt13 indicated certain ranges of composition of the slag in which a

Jan 1, 1923

By Richard S. McCaffery, Joseph F. Oesterele

This investigation was undertaken to determine the quality of different iron blast-furnace slags as desulfurizing agents, and the possibility of using, in the blast furnace, materials of higher sulfur content than is now common. The solution of the problem would render possible the use of higher sulfur iron ores for pig iron and cokes containing more sulfur than now employed, and the economic manufacture of irons and steels of lower sulfur content. It is generally assumed that the sulfur that reaches the lower part of the iron blast furnace is removed from the pig iron by combining with lime to form calcium sulfide. Most of the sulfur introduced with the charge is in combination with iron or manganese or, perhaps in the coke, as a carbon compound.1 The iron and manganese sulfides are more soluble in the iron than is calcium sulfide, and as the latter is generally said to to be more soluble in the slag than the iron and manganese sulfides, this greater solubility of calcium sulfide in the slag tends to free the metal from sulfur. This greater solubility of the calcium sulfide is used not only to reduce the sulfur contents of the pig iron in the blast furnace, but by this means also low-sulfur steels are produced in the open-hearth and electric furnaces. The reaction2 FeS + CaO + CO = Fe + CaS + CO2 requires a high temperature and strongly reducing conditions in the presence of lime. The constitution of blast-furnace slags, first studied scientifically by Vogt13 indicated certain ranges of composition of the slag in which a

Jan 1, 1923

By A. C. Dorenfeld

CHANGES in circuits are often made in milling operations. At the same time that these changes are being evaluated the ores are changing. Even from the same mine, the ore is usually variable as to amount and type of mineral content, degree of association of valuable and gangue minerals, amount and types of soluble salts, hardness, etc. The question then arises whether any small differences in results, after changes have been made in the various circuits, are really due to these changes or whether the variability of the ore can account for those differences. Statistical evaluation provides one method of answering the question that arises so often in beneficiation studies: Did changed results come about because of changed process, or did ore variation cause the change? In this case, data were available for statistical analysis from an operating period of 42 months, representing treatment of approximately 1 million tons of ore. During this period there had been two flowsheet changes: 1) regrind of the zinc circuit middlings was introduced, and 2) alcohol- pine oil frother mixture was substituted for cresylic acid-pine oil frother mixture. Findings are in Table I.

Jan 10, 1954

By Garland R. Dever, Preston McGrain, George W. Ellsworth

Abstract-Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. High calcium and high carbonate limestones suitable for use in cement and lime production, steel manufacture, environment control measures, and other special uses are present in the High Bridge Group (Ordovician) and Warsaw and Ste. Genevieve Limestones (Mississippian). Deposits with thicknesses of 7.3 to 20.7 m, (24 to 68 feet) have been documented by the analysis of samples taken at 0.3-m (1- ft) intervals. Active and potential mine and quarry sites afford access to water transporation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the western Kentucky Fluorspar mining district, and late Paleozoic, erosional unconformities in northeastern Kentucky.

Jan 4, 1978

Receipts, Jan. 1, 1914, to Dec. 31, 1914 Cash on hand, Jan, 1 1914 General Funds $1,843.54 Special Funds 1,039.00 $2,882.54 Initiation Fees $8,500.00 Annual Dues 44,060.84 Life Memberships 1,950.00 54,510.84 Sale of Transactions 4,798.87 Sale of Binding 10,029.06 Sale of Bulletins and Pamphlets 2,508.25 Sale of Special Editions 1,290.74 Sale of Advertising 8,783.29 Sale of Library Books 54.97 Sale of Pins and Fobs 347.65 Miscellaneous Sales 21.66 Space Released 5,943.00 Interest on Investments and Bank Deposits 230.15 34,016.64

Jan 1, 1917

By W. C. Kerr

ThE distribution of gold is obviously much wider than is Commanly supposed. Resides the usual matrices, vehicles, or associates, such as quartz, pyrite, chalcopyrite, etc., I find it occurring in quite a range of common rocks. For example, at the Rhodes mine, in Gaston County, a body of 9 to 12 feet of decoroposed, light-gray gneiss was worked together with the strings of quartz, and yielded from six to ten dollars to the ton. A mine in Moore County yields its gold mainly from a feldspathic schist. In the famous King's Mountain mine, in Gaston County, the gold is obtained not only from the seams of quartz in a blue, hydromicaceous schist, but a 60-foot ledge of grayish-blue, fine-grained, schistose limestone is quarried out bodily and sent to the stamps. It is gold-bearing throughout. In Montgomery County the singular concretionary, conglomeritic, quartzite schist, which contains Emmons's palceotrochis, is gold-bearing over wide tracts of country. This fact was noticed by Dr. Emmons. But a still more striking and significant fact is, that a large part of the gold of Montgomery, Davidson, and Randolph counties,

Jan 1, 1882

By Benny J. Nelson

To obtain information on the effect of gallium upon the corrosion of magnesium alloys, tests were made on the commercial alloy AM52S (Mg-3 pct Al-1 pct Zn-0.2 pct Mn) and experimental

Jan 1, 1957

By W. Mont Ferry

It is impossible to speak in exact terms of the effect that selective flotation has had, is having, and may have on the State of Utah. Its results enter into the economic structure of the state in so many ways and its ramifications are so widespread, that every line of industry is affectcd. Some effects can be definitely determined; others can be reasonably approximated; but the effect as a whole can not be set out in exact figures. Utah is essentially a mining state; mining is its basic industry and always will be. Agriculture, equally a basic industry, and of course, equally vital, can be practiced on only 6 per cent. of the 85,000 square miles of its area. It follows, therefore, that the economic future of this state depends upon a development of its natural resources. About 6 or 7 years ago, the mining industry in Utah was at a low ebb. This condition was caused partly by postwar conditions and other temporary causes, but prevailed also, which was most important, because the direet-smelting ores of the state were being rapidly exhausted and the cost of treatment of complex ores was almost prohibitive. Furthermore, the wet concentration of low-grade ores was unsatisfactory and did not result in producing a good smelting product. On visualizing this situation, one of the large smelting companies in the valley had the courage, ability and faith to develop and expand the principles involved in selective flotation of complex ores. This example has been followrd by other smelting and reduction companirs and the result has changed the entire aspect of the mining industry in Utah. The utilization of the zinc in the low-grade, lead-zinc-silvrr ores was the principal prob1t.m to be solvcd. The average yearly production from the State of Utah for the 10 years beginning 1914 and ending 1923, was something less than 10,000 tons of zinc corlcentrates. This period includes the world war, when abnormal priccs stimulated production. In 1924, selective flotation began to be practiced on a considerable scale, replacing concentration by gravity and bulk flotation which had been used generally until this time. Production and Value of Zinc Concentrates The production of zinc concentrates during 1924 was approximately 24,000 tons, or twice the average yearly production of the previous 10

Jan 1, 1928

By A. E. Himebaugh

A SEMI-AUTOMATIC hoist has been installed at the 2966 station of the Copper Queen mine, since neither the bulk of supplies handled nor the number of men engaged in developing the 3100 level justifies the constant attendance of two cagers and two hoist operators. The connecting service shaft between the 2966 and 3100 levels is actually a two-compartment raise. Below the 2966 level the shaft is 7x13 ft-slightly oversize to permit downcast ventilation and provide space for the 16-conductor flexible control cable. The raise extends 52 ft above the 2966 level for a 3-ft diam head sheave. Another 3-ft sheave is mounted as an idler between the hoist and head sheave, eliminating the need for an inclined cableway. The main compartment serves as a cageway; the other compartment provides a manway and space for service lines. Since vertical travel is limited, rope speed is of minor importance.

Jan 5, 1958

By E. K. Soper

It has been observed that where veins or other types of orebodies are intersected by cross faults, the continuation of the ore deposit below the fault is often of lower grade than that portion above the dislocation.' In some mines, the reverse of these conditions has been noted, and the richest ore is found to occur in that portion of the vein beneath the fault intersection. Such instances seem to be less frequent than those where the richest ore is above the offset. The important and widespread influence of fault and vein intersections upon the localization of ore shoots is well known,2 but the factors that govern the position of the ore shoot relative to the fault intersection seem to be less clearly understood. The richest ore may be above or below the fault, or it may occur at the point of intersection, or there may be no change. Recent observations made by the writer in mines in Idaho and Montana suggested a possible explanation for the changes in the richness of ore below certain types of fault intersections. These observations have been supplemented by a study of the literature containing detailed descriptions of ore deposits at a large number of mines in North America. The results of these studies are presented herewith in the hope that they may lead to further discussion of this important phase of ore deposition. Relative Age oF Faults Faults which intersect veins and other ore deposits may be either pre-mineral or post-mineral in age—that is, they may be older or younger than the deposits which they intersect. Many veins are formed along

Jan 1, 1918

By J. H. Faulk

An examination is made of the various factors influencing drilling rate and drill bit life in various diameter holes. It is concluded that drill bits in the size range 4% to 6 1/4 in. can be used to attain substantially the some daily drilling progress as conventional size bits in soft rock drilling operations. An examination of the most important factors influencing "hazard of losing the hole" in the different hole size results in the conclusion that the smaller hole sizes can probably be drilled at reasonably low risk. However, this risk will be somewhat greater in the smaller diameter holes, requiring that special drilling and mud engineering practices be used to make small diameter holes practicable in soft rock drilling operations. An engineering analysia is made of the power and hydraulic requirements of several drill string-hole combinations to test the feasibility of drilling .small diameter holes in soft rock areas. Large econormies in rig power requirements appear possible by drilling .smaller .size holes in these operations. INTRODUCTION The industry now is re-examining the utility of small diameter holes in the light of substantial technical advances made in recent years. Faced with increasing cost of finding reserves and with proration after developing them, the industry must either develop methods of economizing or receive a lower rate of return on investments. Small diameter holes appear to involve an attractive method of economizing. Our objective is to determine if this is technically possible in soft rock operations. Soft rock, as used in this report, refers to those formations of a "drill-ability" corresponding to that of all Gulf Coast formations shallower than and frequently including much of the Eocene rock system. An important phase of technology which we shall examine is relative drilling rate and bit footage which may be obtained with various size bits. Rig operating efficiency, particularly as influenced by hazard, is also discussed in detail. The technical conclusions resulting from these examinations are used to develop sample drill string design and rig horsepower requirements for drilling holes as smaH as 4 3/4 in. and larger. The principal criterion used for the drill string design is that approximately the same daily drilling progress would be possible in all size holes in soft rock operations. This facilitates a comparison of rig size required for drilling the hole sizes in the range between 4 3/4 and 8 3/4 in. BROAD PROBLEM OF DRILLING RATE AND BIT FOOTAGE The three factors controlling daily drilling progress are: (1) drilling rate of bit while on bottom turning, (2) bit footage, and (3) rig operating efficiency. Let us look now at the first two of these factors. Drilling technology has progressed to the point that a semi-quantitative analysis of the effect of various operating variables upon these factors can be made. Those factors which apparently limit both drilling rate and bit footage for bits now in use are: (1) bit design, (2) weight on bit, (3) hydraulic cleaning capacity for bit cutting surfaces and hole bottom, and (4) rotary speed. (We neglect the effect of mud and formation properties because these factors arc the same for the various size bits.

Jan 1, 1957

By A. Stanley, J. C. Mead

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus % in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9 1/2 in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9 1/2 in. bed sinters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite recovery). These tests have proved successful in increasing ilmenite recovery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was plus from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950