Search Documents

By M. Lastra, A. Cruz, J. Menacho

The use of phosphates was studied as a way of purifying acidic copper leach solutions for direct electrowinning. The addition of 2.5 gpl phosphorus to plant solutions originally containing 6.25 gpl Fe (III) at pH 2 0 reduced the iron concentration by one half. Under identical conditions, but without phosphorous additions, the iron concentration was reduced by less than 1 gpl. Any residual phosphorous had no undesirable impact on electrowinning. The concentration ratio of Fe (III) to phosphorous which provides maximum iron elimination was determined. Higher ratios bring about a redissolution of the iron precipitate. Several ways of controlling iron with phosphates are discussed. These take advantages of more rapid and complete iron precipitation at lower pH levels.

Jan 1, 1980

By H. E. Stauss, G. Sandoz

THE purpose of this note is to draw attention to the possibility that a melt may be contaminated by a material not in direct contact with it by means of gaseous intermediate agents. In recent years silicon has assumed a position of importance because of its use in rectifiers and transistors and close attention has been required to control of both purification and contamination during all stages of preparation.' This note reports the observation that a graphite heater may have contaminated silicon ingots without direct physical contact through reactions that developed gaseous products. Several ingots made with the equipment of Hino and Stauss,2 using a graphite heater in a dried helium atmosphere, were found to have a small amount of a very hard substance on the free surface. X-ray analysis by F. W. von Batchelder showed the sub- stance to be Sic. Similar contamination was not found when the heater was tantalum, indicating that the carbon had not come from an original impurity in the silicon powder. One source of the carbon could have been volatile matter released from the graphite heater. This heater had been used about ten times at the time of the observations. A second source of carbon could have been a direct reaction between the quartz crucible and the graphite heater to form CO, or an indirect reaction involving a crucible-melt interaction and volatile SiO as an intermediate product. Such reactions should have developed Sic on the heater; and in fact a yellow powder did form on the inside of the graphite heater although its composition could not be determined. References 'H. C. Torrey and C. A. Whitmer: Crystal Rectifiers (1948) Chapter 10. New York. McGraw-Hill Book Co. 2 J. Hino and H. E. Stauss: Trans. AIME (1952) 194, p. 656; Journal of Metals (June 1952).

Jan 1, 1954

By C. R. Fast

In order to evaluate the ability of a Hydrafrac treatment to effect a sustained increase in well production, data were accumulated on the first 65 wells in 26 fields treated by Stano-lind. Since these data were obtained from such a large number of fields, it is felt that individual well or reservoir characteristics do not affect the overall picture, as might be the case if the study were made in one field or one group of wells in a field. These data are tabulated in Table I and plotted on Figs. 1 and 2. An analysis of Fig. 1 shows that at the end of six months, 75 per cent, or 45, of 60 wells on which data were available showed a sustained production increase. At the end of two years, data were available on 25 wells. Of these, 15 wells, or 60 per cent, showed a sustained production increase. At the end of three years, 55 per cent, or 10, of 18 wells had a production rate greater at that time than before Hydrafrac treatment. The lack of information on additional wells at the end of the third year is primarily a result of the small number of treatments conducted in the early stages of field application

Jan 1, 1952

By J. Redstone, A. R. Laplante

Sidbec-Normines operates six large iron ore concentrate regrinding mills in parallel and open circuit at its Port-Cartier pelletizing plant. Grinding kinetics in these mills were characterized for slurry densities varying between 70 and 89% solids, using a lumped parameter size discrete model. Optimum grinding conditions were encountered at 83.5 to 84% solids. Higher densities decreased the normalized selection function and increased slurry short-circuiting, yielding a sharply coarser mill discharge. At lower slurry densities, the normalized selection function decreased and the mill discharge coarsened slightly. The grinding kinetic model predicted particle size distributions within the mill. These were found to vary significantly from the feed to the discharge end. This is likely to cause nonlinear breakage kinetics.

Jan 1, 1985

By Alfred F. Brainerd

HAVING had considerable practical experience in the management of colored mining labor in the South, I have thought a few observations upon its peculiarities might interest those not personally familiar with it. In mining, as in all other departments throughout the South, this class of labor is largely in excess of any other; and its characteristics need to be known and duly taken into consideration by those who may be charged with the conduct of southern enterprises. The colored laborers are fervently religious, intensely superstitious, improvident, and usually good natured and happy,—in a word, they are like children. That strong religious emotions do not involve necessarily a moral sense highly developed in the direction of ethics, is shown in the propensity of the colored population for chickenstealing, and in the brutal fights and other outbreaks of which they are not infrequeutly guilty, upon any slight provocation. It is only fair to say, however, that many individuals among them are in the highest degree steady and trustworthy. To one accustomed to seeing white miners at work in the middle, northern or western States, the colored miners seem somewhat slow and lazy. But their efficiency is greater than it appears to be. The almost tropical sun of midsummer beats upon their unprotected heads

Jan 1, 1886

By F. C. Blake

THE test of the English cupellation furnace should be so supported that the cupeller can change readily the elevation of the test, and at the same time watch the litharge channel. It is also important to raise or lower either side, independently of the other, in me of uneven wear of the side walls or of the breast. If the refined silver is poured from the test, it is much better to control the lowering of the test from the front than to raise the back by screws or a lever. In order to enable the cupeller to manipulate the test with one hand, when the litharge is running, and to pour the refined silver from the test without aid, I have altered the common support to the test, as shown in the accompanying drawing. The common method of supporting the test is by four screws, working in cross-bar nuts beneath the test. The points of the screws set, into the test plate upon which the test rests. These screws are usually worked by pounding or pulling upon the heads, which may be either small pulleys or straight bars, as shown on the back screws in the drawing. The screws are also worked by turning a crank, which is

Jan 1, 1882

By F. C. Blake

THE test of the English Cupellation furnace should be so supported that the cupeller can change readily the elevation of the test, and at the same time watch the litharge channel. It is also important to raise or lower either side, independently of the other, in case of uneven wear of the side walls or of the breast. If the refined silver is poured from the test, it is much better to control the lowering of the test from the front than to raise the back by screws or a lever. In order to. enable the cupeller to manipulate the test with one hand, when the litharge is running, and to pour the refined silver from the test without aid, I have altered the common support to the .test, as shown in the accompanying drawing. The common method of supporting the test is by four screws, working in cross-bar nuts beneath the test. The points of the screws set into the test plate upon which the test rests. These screws are usually worked by pounding or pulling upon the heads, which may be either small pulleys or straight bars, as shown on the back screws in the drawing. The screws are also worked by turning a crank, which is

Jan 1, 1882

Meeting of Nov. 21, 1913.-The President reported the appointment of the officers and members of the Committee on Non-Metallic Minerals, published elsewhere in this Bulletin. The President appointed the Executive Committee of the New York Section as a local .committee to have charge of the Annual Meeting of the Institute in February, 1914, with power to add to their numbers. It was voted that the Chairman of each Technical Committee, be made ex officio a member of the Committee on Papers and Publications. At the request of the Secretary, Burr A. Robinson was appointed Assistant Secretary of the Institute. E. Gybbon Spilsbury was nominated as representative of the Institute on the John Fritz Medal Board of Award. It was voted that the next summer meeting of the Institute be held in Salt Lake City in August, 1914, with power to the Executive Committee to fix the exact date. Substantial reduction was made in the price of the back Transactions of the Institute in accordance with the notice published on p. i of this Bulletin.. The By-Laws of the Montana Local Section were approved. The printing contract for the year 1914 was made with the Maple Press. Thirty-eight Members, one Associate and three Junior Members were elected.

Jan 12, 1913

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By M. R. Tek

General equations relating the pressure drop necessary to sustain the flow of a fluid through a porous matrix at a given rate have been developed. The results indicate that at high values of flow rate the pressure-flow behavior may not necessarily satisfy the usual Darcy equation. The mathematical analysis, carried through the micro-pore geometry and extended through the macro-reservoir scale, indicate that Darcy's law, of limited applicability to certain ranges of Reynolds numbers, can be generalized through the inclusion of some additional parameters. The "generalized Darcy equation" has also been formulated in dimen-sionless form permitting the evaluation of its predictive accuracy with regard to literature data. A comparison between predicted and experimental values indicates that the generalized Darcy equation predicts the pressure drops with good agreement over all possible ranges of Reynolds numbers. INTRODUCTION The limits and the nature of validity of Darcy's law' has been a subject of every-day interest to the industry for many years. It is well known that as the Reynolds number, characteristic of the fluid flow through porous media, becomes large, Darcy's law gradually loses its predictive accuracy and ultimately becomes completely void. For the last 20 years much has been said and written on this subject. Unfortunately little has been accomplished to bring about a satisfactory agreement, at least on the nature of the threshold of validity of Darcy.'s law. Fluid dynamists, geo-physicists, and engineers all had their individual views, explanations, interpretations and concepts on the subject. To some, a mechanistic analogy with pipe-flow proved a satisfactory explanation.' To others,' turbulence, in its random character, was incompatible with the geometric structure of consolidated porous systems. To some,4 turbulence merely represented a factor influencing the permeability measurements and again to others5,6,7 em-pirical or semi-empirical correlations proved satisfactory from an engineering viewpoint. Deviations from Darcy's law at high flow rates have been studied by systematic experiments by Fancher, Lewis, and Barnes.' In an article on the flow of gases through porous metals, Green and Duwezs conclude that the onset of turbulence within the pores appears unsatisfactory to explain deviations from Darcy's law. This view is held by many others. While the subject remained controversial for many years, the development of vast natural gas reserves throughout recent years further justified considerable interest on this problem from the standpoint of gas reservoir behavior. As large amounts of field data became available from the operation of many gas fields, it became evident that the steady-state behavior of gas wells was not, in general, in agreement or compatible with Darcy's law. This suggested a careful reconsideration of all mechanisms which may account for pressure drops in addition to viscous shear. In a series of articles9,10 . Hou-peurt indicated that deviations from Darcy's law may be explained on the basis of kinetic energy variations and jetting effects without resorting to assumptions on turbulent flow conditions. Another article by Schneebeli11 indicates that special experiments by Lindquist clearly demonstrated that the onset of turbulence does not necessarily coincide with conditions of deviation from Darcy's law. This view is also held by M. King Hubbert.12 Starting with the basic pressure-flow relations suggested by Houpeurt, the derivation, development and extension of analytical expressions to -supplement and generalize Darcy's law has been the objective of this work. MATHEMATICAL ANALYSIS Derivation of Dimensionless Pressure-drop, Flow-rate Relations In considering the flow of a fluid through a porous matrix geometrically represented by a succession of capillary passages in the shape of truncated cones,810 an approximate expression may be derived relating viscous and inertial, i.e., total pressure drop to the physical properties of the fluid, geometric properties of the rock matrix and the rate of flow: ?P/?r = µ/k V [ 1 + c(m4 - 1) p V/16n" mµ w] ..........(1) Let us formally set: c (m4 - 1) / 16n" m = a d ......(2) Such a representation is equivalent to assert that the term [c(m4 — 1)/ 16n"m], variable with various porous media and probably highly variable within a given porous medium, may be macroscopically defined as equal to a lithology factor times the aver-age grain diameter d. In view of the usual grain and pore size distribu-

Jan 1, 1958

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

By W. Vickers

SALKOVITZ1 has given a number of useful angles between planes for use with the Laue method in determining the orientation of bismuth single crystals. Bismuth is usually considered as having a face-centered-rhombohedra1 structure with its axial angle 87°34', Fig. 1. A similar figure given by Sal-kovitz appears to be in error in that the angle there marked as 87°34' should be 92°26. The primitive cell is a single rhombohedron of axial angle 570 14. The structure is almost face-centered-cubic and hence high accuracy in measurements is essential if there is to be no confusion in indexing poles or zone axes. It is easier to get this accuracy if zone axes are plotted on the stereogram because they will lie near the basic circle where the net has a more open scale. The zone axes can be read from the film, using a Greninger chart, and can be plotted more accurately than poles. Also, the angles between points near the basic circle can be read more accurately than those between poles near the center. In order to use the zone axes the angles between directions have been calculated from a formula given by Niggli,2 and are given in Table I. Miller indices

Jan 1, 1958

By Paul F. Gnirk

INTRODUCTION The notion of permanent disposal of high-level radioactive waste in natural salt formations was formally proposed in 1957 by the Committee on Waste Disposal of the National Academy of Sciences- National Research Council. This proposal was the result of the Committee's deliberations in response to a request from the U.S. Atomic Energy Commission (AEC) in 1955 to assess the viability of geologic formations for such disposal. The research investigations for waste disposal in salt were initiated at the Oak Ridge National Laboratory (ORNL) in the late 1950's and continued through the 1960's and early 1970's at a relatively modest level of funding. During the period of transfer of Federal Administrative authority from the AEC to the Energy Research and Development Administration (ERDA) to the Department of Energy (DOE) during the latter part of the 197O’s, financial support for the research program was enhanced substantially. The program at OWL was regrouped under the Office of Waste Isolation (OWI) and later transferred to the Office of Nuclear Waste Isolation (ONWI) at Battelle Memorial Institute. With this enhancement in the research program, consideration of basalt, granite, shale, and tuff as repository host media was initiated. In February, 1980 the President of the United States established officially a comprehensive waste management program which called for the selection of the first repository site in 1985 from a suite of four or five potentially suitable sites, and initiation of a repository operation at that site in the mid-1990's. The current disposal system concept involves the emplacement of radioactive waste packages in mined disposal rooms at depth in suitable geologic formations, with closure of the facility effected

Jan 1, 1983

By Cyril Stanley Smith

The following table, which is composed of data given in the author's first paper on the thermal conductivity of copper alloys1, contains tile results which have been obtained by previous workers on the thermal conductivity of the copper-tin, the copper-phosphorus and the copper-tin-phosphorus alloys (the phosphor bronzes). a Dr. Ing. Diss., Aachen, 1909. Quoted by Schenk: Ann. der Phys. (1910) 32, 261. b Beibl. Ann. der Phys. (1906) 29, 178. c Jnl. Inst. Metals (1928) 39, 375. d Jnl. Inst. Metals (192.5) 34, 43. e Ges. Abhand. Kennt. Kohle (1919) 4, 400. Experimental Methods Since the method of obtaining measurements of the thermal conductivity was identical with that described in the author's previous paper

Jan 1, 1931

J. E. JOHNSON, JR., New York.-It seems to me that it ought to be somebody's job to tie these notch tests with the reversed-stress tests, because the thing that causes failures in structures, in a great majority of cases, is where the material is stressed repeatedly up somewhere near the elastic limit, and the repetition of that stress seems to bring about what I suppose you may call a growth of crystals and that eventually develops into a break. It seems to me that it would be of the greatest value if there could be a coordination of the results of a shock test of some kind with the reversed-stress test, so that we could be sure that a material that had shock-test resistance would have reversed-stress resistance. H. F. MOORE,* Urbana, Ill.-The question raised by the speaker concerning the correlation of results from impact tests of notched bars with the results of repeated-stress tests is a very complicated one. Impact on a specimen sends energy into the specimen, and if the specimen absorbs this energy without fracturing there must be developed both stress and elongation. A notch in the specimen allows but little elongation to take place before rupture, and develops the ductility of the

Jan 5, 1919

By A. H. Daane, R. L. Myklebust

The yttrium-manganese system has been investigated by thermal, metallographic, and X-ray diffraction methods. There are three intermetallic compounds present: YMn2 which melts congruently, YMn4, which undergoes syntectic decomposition, and YMn,, which undergoes peritectic decomposition. The compound YMn4 is ferromagnetic at room temperature with a Curie temperature of 214°C. There are eutectics at 25.2, 60.9, and 82.0 wt pct Mn which melt at 878°, 1100°, and 1075°C, respectively. Crys-tallographic data are given for YMn4, and YMn12 . The terminal solid solubilities are low. In a general program of study of yttrium metal in this laboratory some alloy systems of this metal with elements of the first transition period have been examined. This work was originally instigated by experiences in cladding yttrium with jackets of some protective metals such as Inconel for high-temperature service in air.' In some cases a low-melting phase was observed to form between the Inconel and the yttrium resulting in failure of the samples. In characterizing this reaction, a survey was made of the systems of yttrium with chromium, manganese, iron and nickel,, and it was found that a eutectic was formed between these metals and yttrium on the yttrium-rich side of the system. This present study of the Y-Mn system was carried out to examine in more detail the alloying nature of yttrium, and to correlate trends that have been observed in previous related studies. It was observed by Voge13 that in the systems of lanthanum, cerium, and praseodymium with each of the metals in the first transition series, the tendency to form compounds diminished in the order nickel, cobalt, and iron while no compounds were formed with manganese, chromium, or titanium. Beaudry and Daane4 observed a similar behavior in the systems of yttrium with some members of the first transition series except that the tendency for compound formation was greater. Both the Y-Ti5 and Y-Cra systems consist of simple eutectics, while in the Y-Fe,7 Y-CO, and Y-Ni4 systems, there are four, eight, and nine compounds, respectively. In addition to the above trends, the similar atomic radii and electronegativities of yttrium and thorium invite a comparison between their alloying behaviors with a common element such as manganese. In crys- tallographic studies, Florio et al.' have identified three intermediate phases in this system which are ThMn2, Th6Mn23, and ThMn,,. Gschneidner and Waber10 have examined published information on alloy systems of the rare-earth metals and have correlated this information with current alloying theory. From their study, they predicted that the Y-Mn system would contain one intermetallic compound. On the basis of this prediction, the trend in the alloying behavior of yttrium with the elements of the first transition series and the alloying behavior of thorium with manganese, one might expect from one to three intermetallic compounds to form in the Y-Mn system. A consideration of Hume-Rothery's rules of alloying based on size-factor, electronegativity, and valency suggested a small terminal solubility and possible compound formation. The present study was undertaken to confirm these predictions of low terminal solid solubility and compound formation and to establish the general alloying behavior of yttrium with manganese. EXPERIMENTAL Materials. The manganese used in this investigation was obtained from the Foote Mineral Co. as electrolytic plates of 99.9 pct stated purity; the yttrium metal was prepared in this laboratory. Table I gives the analyses of these materials. For the solubility studies at the yttrium-rich end of the alloy system, distilled yttrium, whose major impurity was 200 ppm Ti, was used. Preparation of Alloys. The alloys were formed by comelting the two metals in an are-melting furnace under an atmosphere of argon. The buttons thus formed were inverted and remelted three to five times to promote homogeneity. Due to the high vapor pressure of manganese, it was assumed that the weight lost during are-melting was all manganese. This assumption was based on the very good agreement observed between calculated compositions and chemical analyses of several alloys. The compositions of the dilute alloys used for solid solu-

Jan 1, 1962

By Arthur Philips

THE purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreover, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the tests and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstructure of white cast iron by annealing at different temperatures within the range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800° C.

Jan 1, 1922

By G. R. St. Pierre, L. M. Adelsberg, R. Speiser

OXIDE platelets have been observed'-3 in oxidized tantalum adjacent to the metal-oxide interface, Fig. 1. The origin and identity of the platelets are important with respect to the proposal of an acceptable mechanism of tantalum oxidation. At reaction temperatures below 750°C, it has been established that the platelets

Jan 1, 1967

By Cyril Smith

ALTHOUGH alloys of copper and silicon were examined several years ago,1 and their excellent mechanical properties were shown, it was not until C: B. Jacobs2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass. Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. REVIEW OF PREVIOUS WORK ON, THE BINARY SYSTEMS There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described,3 which indicate that there is a change insolubility with temperature.

Jan 1, 1930

By D. A. Hinckfuss

The large and compact but simple Bougainville Copper Limited flotation circuit has been in operation for 3-1/2 years. Discussion of problem areas encountered since start-up and remedies that have been implemented or proposed, form the main basis of this paper. Full current operational data is also provided.

Jan 1, 1976