Search Documents

By A. W. Fahrenwald

The physics and chemistry of the flotation process are not well understood. Many papers dealing with the theory of flotation have been published but most have been narrow in their viewpoint. No theory advanced has done more than explain, more or less satisfactorily, various isolated phenomena. Scientists have done little with the problem, doubtless because they have not seen sufficient of the practical side of the subject to have their interest aroused. Any attempt to explain the mechanism of flotation that considers only contact angles, surface tension, adsorption, the floating of needles, flocculation, or any other single and narrow phase of the question is sure to be disappointing. Flotation is a problem of colloid chemistry and must be studied as such. In a broad general way, flotation is a process involving and operating by virtue of surface reactions. The term "surface reactions" may be open to criticisms. Many chemists give the term "reactions" a definite and restricted meaning and to such the term may connote change in atomic grouping in strict stoichiometric ratios. While Langmuir looks upon adsorption as a reaction, and there is much evidence in support of this view, we may look on adsorption as a physcial process as far as this paper is concerned. The term seems well suited to the work in general. Presumably these reactions are reactions between the same kinds of forces (electrical) and differ only in degree and in the surface manifestations produced. This premise seems logical if we accept the theory that the atoms of dl elements are made up of grains of electricity, having mass and charge, called electrons; and that atoms differ from one another only in the number and arrangement of the electrons about a positive nuclear

Jan 1, 1924

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals' has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals' has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By Bruno V. Nordberg

The high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapt- ing this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 1, 1914

By Edgar C. Bain

Jan 1, 1932

By V. H. Gottschalk

SEVERAL years ago a group in the metallurgical division of the U. S. Bureau of Mines began a study of the application of new developments in physics to metallurgical problems'. Among these developments were the extensions of what may be termed by analogy the "sound spectrum." Electromagnetic waves, from X-rays to radio waves, have been quite thoroughly explored for metallurgical use, but the sound spectrum, extending from low-frequency vibrations involved in certain types of metal failure by fatigue through the range of audible sound to inaudible vibrations having frequencies of many kilocycles, has had only meager consideration from metallurgists. Because of the general interest in the process recently demonstrated by St. Clair3 for flocculating smoke by means of sound waves, this article is written to point out possible applications of sound and supersonic (ultrasonic) waves in the metallurgical industry.

Jan 1, 1937

While coal was mined in New Mexico in 1860, production was on a small scale during the period considered here, and Table 77 contains all the data found. [ ]

Jan 1, 1942

By G. Thodos, R. B. Grieves

A method has been developed For predicting the critical temperatures and critical pressures of binary mixtures of carbon dioxide, hydrogen sulfide, nitrogen, hydrogen, carbon monoxide and oxygen with the normal paraffin hydrocarbons. For carbon-dioxide and hydrogen-sulfide systems, relations are presented that take into account the peculiar behavior of mixtures with closely boiling components, such as carbon dioxide-ethane and hydrogen sulfide-propane mixtures which exhibit minimum critical temperature points. For hydrogen, nitrogen and carbon-monoxide systems, the extreme critical behavior caused by wide differences in pure component properties is established In addition, those fixed gas-paraffin systems which resemble paraffin-paraffin systems are also accounted for. For a mixture of known composition, the pure component critical temperatures, critical pressures and normal boiling points are all that are required to determine its critical point. Graphical relations are presented relating Tc and PC , of the mixture to the pure component properties. From the treatment of 12 carbon-dioxide and hydrogen-sulfide systems reported in the literature (74 mixtures), the expected error lor the critical temperature is approximately 1.5 per cent, and for the critical pressure, approximately 2 per cent. From the treatment of six hydrogen, nitrogen and carbon-monoxide systems reported in the literature (30 mixtures), the expected error for both the critical temperature and critical pressure is approximately 2.5 per cent. The relationships, which have been developed with only normal paraffins as the hydrocarbon components, may be extended to those isoparaffins and olefins which fall within the allowable volatility ranges. INTRODUCTION Many of the fixed gases — carbon dioxide, hydrogen sulfide, nitrogen, hydrogen, carbon monoxide and oxygen — occur in natural mixtures with hydrocarbons. Carbon dioxide and hydrogen sulfide are frequent components of the fluids produced from underground petroleum reservoirs. Nitrogen, carbon dioxide and hydrogen sulfide are present in varying quantities in most natural gases and gas-condensate well effluents. Hydrogen mixtures are of considerable interest in many phases of refining processes of petroleum. The determination of the critical temperatures and critical pressures of such mixtures is of value in vapor-liquid equilibrium studies, for the prediction of the characteristics of underground reservoirs, and for reduced-state correlations of PVT, transport and thermodynamic properties. The accurate estimation of the critical point for binary mixtures is an important initial step toward a complete analysis for the establishment of the critical temperatures and pressures of multi-component mixtures. Methods for predicting the critical temperatures and critical pressures of binary hydrocarbon systems have already been presented in the literature.8 It is possible to apply these existing methods to fixed gas-paraffin mixtures, but due to their unusual critical behavior, values calculated deviate considerably from experimental values. For systems containing trace quantities of the fixed gases, these methods are acceptable; however, for systems containing more than 5 mol per cent of the fixed gases, these utterly fail to produce reasonable critical values. Consequently, in this study a method has been developed for handling such binary mixtures over the entire composition range. CARBON-DIOXIDE AND HYDROGEN-SULFIDE SYSTEMS The critical behavior and the vapor pressure behavior of mixtures of carbon dioxide and hydrogen sulfide with paraffinic hydrocarbons may be quite similar or quite dissimilar to that of paraffin-paraffin mixtures, depending on the volatilities of the components involved. The critical temperature and normal boiling point of carbon dioxide are very close to the corresponding values for ethane, while its critical pressure is considerably higher than that of ethane. The normal boiling point of

Jan 1, 1902

By Frank Riddle

PRODUCTS made from the ores of the sillimanite group, and synthetic substitutes for them, have unique properties, and service tests prove that they are playing, and will continue to play, a major part in improvements in metallurgical processes. Also, they are examples of how comparatively useless, rare, or "museum" minerals have been made available in commercial quantities. Until research developed uses for them, the minerals had been observed only in small, scattered masses, or crystals. Improvements in ceramic processes and compositions have come about very gradually. In the last 10 or 15 years, several outstanding developments have been made. Of greatest interest to the mining and metallurgical engineers are those affecting the composition, necessitating the mining of new minerals, and improvements in ceramic products used in metallurgical processes.

Jan 1, 1932

By Coolbaugh, Franklin

CRUSHING of Climax mine-run ore is carried out in two plants: No. 1 plant (flowsheet in Fig. 1) has a capacity of approximately 5000 tons per day. It is used as a stand-by except when maximum production is required. No. 2 plant (Fig. 2) has a top capacity of approximately 17,000 tons per day. The No. 2 crusher is more efficient to operate on reduced tonnages regardless of the wide variation in peak capacities. The system of crushing is similar in both plants: Mine ore, of a size which can be drawn through 48 by 96-in. slusher openings underground, is dumped into the crusher bins from ten-ton mine cars and fed into 48 by 60-in. Buchanan jaw crushers by means of chutes and Ross chain feeders. The jaw crushers are set to discharge at approximately 9-in. size. Jaw crusher discharge is conveyed to 7-ft. Symons standard cone crushers where it is broken to minus-2-in. size,

Jan 1, 1946

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the sane. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known. GENERAL METHOD The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do's or the H'S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.' In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,' the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.' Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.' The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.'' Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

By Peter N. Blakey, Thiann R. Yu, Douglas O. Tansey

A flexible, efficient, and relatively low-cost drilling and blasting operation has evolved at Texasgulf Canada, Ltd.'s Kidd Creek underground mine. Located 32 km (20 miles) north of historic Timmins, Ontario, the underground operation utilizes a sublevel open stoping method developed with large-diameter blastholes. Over the years, Kidd Creek engineers have experimented with various drill-and-blast techniques, leading to the present-day practice. Continuing work is being conducted to further mechanize the blasting operation.

Jan 6, 1976

By F. C. Langenberg

IT is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy and Cornu-Thénard justify the assumption that the precision obtained by this machine is comparable to that obtained by, the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal .direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cornu-Thénard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several

Jan 8, 1919

Jan 1, 1902

By A. P. Svenningsen

DURING the work at the test mill in Morenci, it was determined that a suitable feed for the ball mills could be made by a single pass through a short-head cone crusher. These crushers did not require a closed circuit delivering only a screen product to the mills, such as is the practice in some concentrators. By no means does this mean that the practice in these other concentrators is wrong, but just that the Morenci ore can be most economically crushed and ground in this manner. Therefore, the design of the secondary crushing plant was simply a problem of taking 25,000 tons of ore per 16 hour day from the primary crusher, this ore ranging in size from fine particles to 10 or 12 in., and reducing it to minus 3/4 in. Inasmuch as outages must be contended with in any crushing plant, it was assumed that the crusher would operate at full capacity for approximately only twleve hours per day, which is three-quarter capacity for the 16-hour shift. With this in mind, it was necessary to design a crushing plant which would average approximately 1600 tones per hour for the 16-hour day, or 2000 tons per hour for slightly over 12 hours per day.

Jan 1, 1942

By L. D. Jaffe

IT is now well established that quenched and tempered titanium alloys have much better ductility when the quenching is from a two phase a-B structure, rather than from an all B structure. The corresponding microstructural differences, however, have not been shown in previous publications. Accordingly, specimens were cut from a % in. rod of commercial RC-130A, containing 7.9 pct Mn and 0.12 pct C, which had been previously hot rolled, heated 1 hr at 1100°F, and air cooled. (The same heat has been studied by others." 7 Samples about 1/4 in. cube were heated in helium 1/2 hr at 1450' or 1700°F, quenched in brine, tempered in helium 1 hr at various temperatures up to 1250°F, and quenched in brine. They were then sectioned and metallo-graphically examined, using an etchant of HF-HNO, in glycerine. As quenched from 1700°F, the microstructure observed was clear /3. (Probably also present was U, as the hardness was 400 Vhn, but w is not yet reliably revealed by any metallographic technique.) When the /3 quenched alloy was tempered at a high temperature, a precipitated as a grain boundary film

Jan 1, 1957

By C. C. Furnas

IT is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investigations1 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper.

Jan 1, 1929

By Clarence S. Ross

INTRODUCTION THIS chapter on the rô1e of physical-chemical processes in ore deposition presents unusual difficulties because it attempts to discuss the theory of processes that are very imperfectly under- stood, but which are among the most fundamental problems now before the student of ore formation. It is generally believed that a great variety of ore deposits are in some way derived from igneous rocks; but we desire to know the mechanism of their splitting off from the parent magma, the physical and chemical character of the material that acts as a medium for transfer from magma to the point of deposition, the manner of deposition, and the methods of replacement and removal of the invaded rocks. This problem is difficult for the field geologist because it concerns forces that for the most part have long since ceased to act. It involves a complex system of which the time for completion extends from the first development of the parent magma through its intrusion, its slow cooling and crystallization, and the final escape of its last residuum, a time probably represented by millions of years. In space the processes extend from profound depths of the abyssal magma which can never be directly observed, through the horizons characterizing deep-seated igneous rocks and ore deposits; those formed at moderate depths; and ends with surficial ones and surface thermal springs. The geologist usually can study the effect at but one of these horizons: he must attempt to fit his puzzle together while seeing but a few parts at a time. Thus he must deal with many isolated phenomena, as if they were the result of many physical and chemical systems; when in fact his problem involves a single exceedingly complex system, and will only be understood when that entire complex system is understood. The geophysicist is handicapped because he must attempt to interpret an extraordinary complex system, involving physical and chemical conditions which he can never hope to duplicate fully, through the study of many exceedingly simple systems.

Jan 1, 1933