Search Documents

By Robert Mehl

THE Widmanstätten figures found in the steels have been long recog-nized and in some aspects carefully studied,1 especially as they occur in cast hypoeutectoid alloys. Aside.from the practical importance of the structures obtained in the steels by various heat treatments, a study of the characteristics of these figures is interesting because of the rich opportunity the system affords, to, obtain new data on the mechanism of segregation from solid solutions. This opportunity is twofold: first, by changing composition within the austenite range the proeutectoid precipitate may be changed from that of ferrite to that of cementite, thus offering the same opportunity for changing the type of precipitate while maintaining the same basic lattice as that afforded by the Cu-Zn alloys;2 and second, the eutectoid inversion leads upon drastic quenching to the formation of martensite, a Widman-stätten figure of unique interest from ;the crystallographic viewpoint, particularly in comparison with those formed on-slow cooling.3 We have, therefore, two types of structure to study: that formed on slow cooling of hypoeutectoid and hypereutectoid alloys, and that formed on quenching hypoeutectoid, eutectoid, and hypereutectoid alloys. For each of these types of structure we require the crystallographic plane in the mother austenite along which the precipitate forms (we shall see that the precipitates in these alloys are invariably platelike in form), and also the orientation of the precipitate upon this plane. Some of these

Jan 1, 1933

By E. D. Gardner, E. M. Sipprelle

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321-325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale deposits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 90 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;' the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surfac,e samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name "oil shale" is unfortunate, as the rock is a tough, strong marlstone. Organic matter named "kerogen" is a constituent of the rock. The oil-shale demonstration mine is on Naval Oil-Shale Reserve No. 1; it is about 5 1/2miles by mountain road from the plant site, which, in turn, is 2 miles from U.S. Highway 6 and 10 miles west from Rifle, Colo. The highway parallels the Colorado River, the Denver and Rio Grande Western Railroad, and a 66,000-volt public-utility power line. Early in the program it was realized that an oil-shale enterprise would have to be on a large scale to be commercial, and that unusually low mining costs would be necessary. The physical characteristics of the Mahogany Ledge and an overlying roof stone are unusually favorable both for large-scale operation and low mining costs. Quarry practices largely will be followed underground to mine the Mahogany Ledge. The aim has been toward complete mechanization of all mining operations. A mining unit would comprise a square mile containing 100,000,000 tons of oil shale with allowance for mining losses. An investment of $1,000,000 would be $0.01 a ton; such an expenditure, therefore, could be made to save, say, $0.015 per ton daily operating cost. A goal of a mining cost of $0.50 per ton was set up in 1945. Open-cut mining costs then were about $0.25 per ton of material handled; it was hoped that a cost double this amount could be obtained in mining the Mahogany Ledge. Costs of labor and supplies have increased since 1945 and so has the selling price of petroleum products. To those unacquainted with the character of the Green River deposits, the name "shale" suggested high mining costs. Others assumed that coalmining costs of $2 to $5 per ton would apply. To many, the expected mining costs appeared the principal handicap to the establishment of an oil-shale industry. The purpose of the Bureau of Mines is to demonstrate methods and to establish costs for mining the oil shale on a large scale. It is hoped this work will lead to the establishment of a large-scale, commercial oil-shale enterprise.

Jan 1, 1950

By C. S. Matthews, P. Hazebroek, H. Rainbow

It ha been suggested that lormation fractures created by well stimulation treatments will adversely affect sweep-out efficrency in injection operations. Fluid-flow model studies involving vertical fractures of various lengths and fluid systems of various mobility ratios have been carried out to study this subject. In addition, limited data have been obtained on one model containing a horizontal fracture. It was found that relatively long and highly conductive fractures (not generally obtained fracturing operations) were required to affect the sweep-out efficiency substantially. In a given case in the field an approximate distinction can be made between the presence of long conductive fractures and shorter or less conductive ones. This is done with pressure build-up analyses along with data on the relationship of fracture length and conductivity to well productivity. This type analysis shows that usually the fractures induced are either short or of limited conductivity and therefore do not damage sweep-out efficiency. INTRODUCTION Improved well productivity and in-jectivity can frequently be exploited in injection operations. Higher total throughput can yield improved economics. On occasion, the achievement of an increased productivity or injectivity in specific wells can bring about a more uniform sweep of the reservoir. Higher rates can be exploited particularly in water floods of "depleted" reservoirs where a rapid "fill-up" is desired and where low pressures contribute to low well productivity. The creation of fractures local to the wellbore is an excellent means for achieving these objectives. Even though fracturing has been employed in some floods with success,1"3 there still seems to be some reluctance to employ this tool for fear of undue damage to the flood pattern and ultimate recovery. We therefore need to examine the influence which fractures of varying length may have on flood performance and then determine the length of fractures which obtain in the field with conventional fracture treatments. A substantial influence of fractures on the recovery obtained at breakthrough of the injected fluid has been presented by Crawford and Collins for equal fluid mobilities for the line-drive pattern.4,5 In addition, the influence which a fracture has on the production performance after breakthrough and on the ultimate recovery warrants consideration in reaching a conclusion concerning the use of induced fractures in flooding operations. This report presents this type of data for the five-spot injection pattern for several fluid mobilities. In arriving at some conclusion concerning the fracture lengths obtained in field operations we must examine the performance characteristic most affected by the fracture. This is the change in the flow system as reflected in the change in productivity and pressure build-up behavior. A study of these changes is also presented in this report. RESERVOIR ANALOGS The X-ray shadowgraph technique, employing miscible displacement in porous models, has been used in the study of the influence of fractures on pattern sweep-out efficiency. The X-ray shadowgraph procedure is described in detail in an earlier report8. Fractures were represented by leaving the proper portion of the model surface exposed to either injection or production. This assumes the fracture resistance to be negligible compared to that of the formation. Actually the flow resistance in propped fractures obtained in the field is sometimes not negligible so that the results with this model indicate the maximum influence of the fracture. Two types of models were necessary to represent vertical fractures in a five-spot flood. These pattern elements are illustrated in Fig. 1. In studying the influence of the horizontal fracture, only one well spacing length to thickness ratio of 50 was used. The pool unit of a Carter Electric Analyzer was used in studying the influence of fractures on productivity and build-up behavior. The square drainage system of a well was represented by a network of 576 elements of equal volume and resistance. One-fourth of this drainage area was studied as a model unit using a network of 144 condensers and resistors. Vertical fractures were represented by a shunt directed from the well perpendicular to the drainage boundary. Horizontal fractures were represented by a circular shunt. Resistance of a shunt was varied in representing different conductivities for the fractures. FRACTURE DIRECTION AND LENGTH The direction at which a vertical fracture extends into the formation and its length and conductivity influence the sweep behavior. The two

(There are 82 Local Sections in the United States, 10 Foreign) ADIRONDACK Established June 18, 1952 Official year begins in January Meets next to last Saturday monthly April through October Local Section Dues AIME Mbrs $2 Affiliate Mbrs $3 Severn P Brown, Chairman George E Erdman, Vice-Chairman Patrick F Farrell, Secretary-Treasurer Republic Steel Corp Mineville, N Y

Jan 1, 1960

By Frank M. Howell, Claude E. Schmidt

To counteract the spiralling costs of labor and materials against the fixed sale of its product, namely, gold at $35 per oz, Homestake Mining Co. has revised the milling flowsheet once and effected increases in the daily milling rate twice in the past 12 years. During this period the mining department has been able to hold production costs steady by increased productivity through technical improvements and utilization of the most modern mining by CLAUDE E. SCHMIDT and FRANK M. HOWELL, JR. 46-MINING ENGINEERING, APRIL 1963 equipment. The flowsheet alteration occurred during 1951-1953 when the two crushing plants at the shaft head frames were converted to a three-stage crushing system with the third stage closed circuited to produce a minus 5/8-in. product as rod mill feed.

Jan 4, 1963

By L. F. Porter, G. J. Dienes

The effect of netltron irracliation on mart ensite transformation in the iron-nickel system was studied by means of electrical resistance and magnetic induction measuremertts. Irradiation lowers the M8 temperature of the allay, causes changes in the electrical and magnetic properties of the high-temperature phase which indicate either an accelemtion of phase separation or a clustering of nickel, and enhances strain recovery on specimens partially transformed to martensite prior to irradiation. Possible mechanisms to account for the effects; are discussed. 1 HERE is a good deal of evidence to indicate that neutron irradiation is capable of affecting phase changes in metals and alloys. While the mechanism of the effect often is not well understood, such studies hold promise of improving our understanding not only of irradiation damage but also of the phase changes involved. To date systematic and detailed investigations have been made of the influence of nuclear radiation on order-disorder transformations in the copper-gold, nickel-manganese, and copper-zinc system, and on precipitation reactions in the copper-iron, nickel-beryllium, and copper-beryllium system.' These solid-state reactions are diffusion controlled and the results can be explained largely on the basis of enhanced diffusion due to the presence of irradiation produced vacancies. Reversion of low-temperature eutectoid phases to the high-temperature phase has been observed in the fissionable uranium-molybdenum and uranium-niobium systems.2 Here it is necessary and logical to postulate a displacement spike mechanism to account for the effect. The only case of irradiation induced diffusionless transformation in metals is the allo-tropic transformation of p to a tin reported by Flee-man and Dienes. 3 They found that neutron irradiation markedly decreases the incubation time for transformation, but the mechanisnl is not well understood. Another diffusionless transformation which one might expect to be influenced by neutron irradiation is the martensite transformation. This transformation is known to be sensitive to strain, structural hardening, and the presence of imperfections.6,7 Since the transformation is diffusionless, one also

Jan 1, 1960

By Henry Ferguson

THIS paper is a preliminary statement, intended to present the more important results of the recent studies of the ore deposits of the Alleghany district in advance of the publication of the complete report, now in preparation. The Alleghany district (Fig. 1) has been a producer of gold since the early days of California gold mining. As in other California gold camps, placers yielded the bulk of the earlier production, but during the last 30 years lode deposits have been the only important source of output. The district differs from other California gold-quartz districts in that nearly all the production is from small shoots of high-grade ore. The mining camps of Alleghany and Forest are on the western flank of the Sierra Nevada range about 20 miles west of the crest. The gently sloping lava-covered plateau which controls the upland topography has been trenched by deep canyons of the westward flowing streams, which are cut to depths of as much as 2000 ft. below the crests of the ridges. The district is about 18 miles from Nevada City but the automobile road which connects the two places is 31 miles long. The senior writer first visited the district in 1913 and published a short description of the lode deposits.1 The increasing importance of the district made further study desirable. A detailed topographic map was therefore made by W. B. Upton, Jr., of the U. S. Geological Survey, in the spring of 1924, and the senior writer spent parts of the field seasons of 1924 and 1925 in the district. For the second field season the Geological Survey was fortunate in securing the services of R. W. Gannett, who had already done geologic work in the district for several of the mining companies. Owing to the death of Mr. Gannett in October, 1925, just before the close of his field work, the work of preparation of the entire report fell to Mr. Ferguson. He takes this opportunity of acknowledging how deeply he is indebted to Mr. Gannett for his excellent work in the field, and his realization of how greatly the completion of the report on the district has suffered from lack of Mr. Gannett's assistance in the office. In October, 1.928, after the completion of the first draft of the manuscript, Mr. Ferguson made a short visit to the district.

Jan 1, 1929

By A. M. Gow

THE trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed, and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling.

Jan 1, 1930

By Dean, R. S.

THE numerous theories of hardening which have been advanced in recent years are all satisfactory in accounting for some of the phenomena observed in hardening metals, but none so far presented account for all of the facts observed. Some years ago one of the authors, R. S. Dean,' presented a theory to account for some of the properties accompanying work hardening. The present paper develops this theory further in the light of recent experimental work and extends it to other forms of hardening. Many of the ideas included have come from the writings and personally communicated thoughts of others. We have attempted to give proper credit in every case, but it is possible that we have not always done so. As an historical basis it is desirable here to review very briefly the hardening theories which have been current. The first comprehensive theory of work-hardening phenomena was due to Sir George Beilby.2 He contributed the idea that with cold work part of the structure of the metal was rendered amorphous and that-it was to this amorphous material that the cold-worked metal owed its difference in properties. According to Beilby's theory this amorphous material was a supercooled liquid and, therefore, had the characteristics of a vitreous material. That such a theory is not capable of explaining the property changes in metals has been repeatedly pointed out. This theory also allowed a slip to take place only once on a given plane, which, as has been pointed out by Jeffries and Archer13 is not consistent with the observed length of an, individual slip and the amount of elongation which can be obtained by wire drawing. The modifications, which have been proposed to this hypothesis to make it coincide with the experimental facts, have to a considerable extent robbed the theory of its clean-cut characteristics. The commonest of these modifications replaces the amorphous phase with an

Jan 1, 1927

By L. R. MacLead

Delivery of tailing to any part of the area by gravity from the ridge was found practicable. Experiments with asbestos-cement pipe proved it possible to use level pipe across the dams if it is fed through an inclined section in which pressure could be developed. Use of pipe to transfer the tailing to the dams was not favored because of the possibility that choking might occur. Metal flume was not believed to have sufficient wear resistance on this material and wooden flume would not withstand damage by the weather so well- Flume -action made- of 26-in diameter asbestos-cement pipe, split before curing and molded to a specified cross section, were finally approved. The flume is connected to the 24-in. diameter tail in distribution pipe by heavy concrete lateral launders. Cascades of horizontal and vertical pipe sections are used at the top of the pressure leg where scouring by high-velocity flow of tailing might occur.

Jan 1, 1942

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to be- gin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTLIRES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, de- pending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1964

By Victor Homerberg

A STUDY of the correlation of the mechanical properties, and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the manufacturer. The results obtained by Babson and Buhler,1 Bengough and Hudson,2 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470° C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200° C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a ¾ -in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 3, 1924

Part 1. Coal Part 2. Industrial Minerals

Jan 3, 1977

By A.J. PHILLIPS, Wm. B. Price

ADMIRALTY nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Win. B. Price1 described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.2 A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm.. Gallimore & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four, binary copper-nickel alloys of the compositions shown in Table 1. Various amounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by melting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of these castings was polished and etched for-examination. The castings were not homogeneous solid solutions, but showed the usual cored structure associated with cast alloys. However, from an examination of these sections we roughly determined

Jan 1, 1928

[NORTH AMERICA UNITED STATES Alabama BIRMINGHAM BURROWS, WILLIAM C. CORD, RICHARD H. COSTON, OTIS D. JR. FAIRHOPE RUFFLES, WILLIAM R. HUNTSVILLE WAGGONER, JERRY B. MOBILE PETROUTSON, PETER C. SELMA JONES, JAMES J. JR. UNIVERSITY CUDWORTH, JAMES R. JONES, WALTER B. RICHARDS, EDWARD F.]

Jan 1, 1961

By H. H. Kellogg

Available high-fernperatzwe equilibrium measurements and other thermochernical data have been critically reciewed for sulfation reactions of the type: Recommended values for log K and ?Fo as junctions of temperature are given for thirty-six suck reactions involving twenty-six different metals. Methods of calculation and choice between conflict-ing data are discussed. SELECTIVE sulfation now enjoys a considerable renaissance as a metallurgical unit process due, in large part, to the available of the fluid-bed re- actor—a device capable of the close control of temperature and gas composition necessary for a successful sulfation process. An additional need, however, if sulfation chemistry is to be approached in a scientific manner, is a reliable body of data on the equilibrium and kinetics of sulfation reactions in simple and complex systems. This paper offers a critical review and compilation of equilibrium data on pure sulfates (simple systems). The last such review, by K. K. Kelley in 1935:30 has proven itself most useful, but the existence of many new data makes necessary a re-evaluation of the available information. METHODS OF CALCULATION For a simple sulfation reaction such as MS04(c) = MO(c) + SO3 [1] there are two approaches one may take toward establishing the value of ?Fo or K as a function of

Jan 1, 1964

By Frank J. Tolonen, Nicholas H. Manderfield, Paul Jasberg

EARLY in the study of the low grade iron formations of Michigan, wide variations in their structure and texture became evident. Because of these variations no simple method of concentration is possible, and those portions of the formations that can be exploited profitably under a given stage of metallurgical progress and existing economic conditions must be searched for carefully. Both structure and texture of the formations have an important bearing on their amenability to beneficiation. By structure is meant the banding planes of easy fracture, the porosity, and the degree of leaching. Texture, which includes grain sizes, shapes, and degree of interlocking, determines the amount of grinding necessary to liberate the mineral grains. Structure determines the liberation of portions richer in one mineral. Structure and texture may be termed the gross features of the formation

Jan 11, 1957

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.' Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

By R. S. Hooper

In attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope tonnages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 11/2 hr per shift, Or 25 PCt of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1949

By Robert Leach

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928