Search Documents

By Edward W. Parker

One of the most important features of the coal-mining industry of the present day is one that is common to the majority of industrial enterprises—the substitution of mechanical methods for hand-labor.

Jan 1, 1900

By E. H. Bunce, E. C. Handwerk

The inherent difficulties of zinc smelting arise from the fact that metallic zinc is volatilized at the reducing temperature of zinc oxide and thus is liberated in the form of a vapor. This vapor must be subsequently condensed to obtain metallic zinc, first in molten and eventually in solid form. Zinc vapor is sensitive to oxidation not only by air but by combustion gases containing carbon dioxide. It is, therefore, necessary to carry out both the reduction and the condensation operations in a closed system consisting of an externally heated muffle with attached condenser from which extcrnal oxidizing agencies are excluded. However, the reoxidation of zinc vapor cannot be entirely prevented by excluding external sources of oxidation. Internal sources of oxidation are necessarily present when oxidic zinc ores are reduced by a carbonaceous reducing agent. The reduction reactions themselves involve, first, the production of carbon monoxide in an amount at least equal in volume to the zinc vapor produced in the reaction, and, second, the formation of carbon dioxide. Not all of the carbon dioxide is reduced again to carbon monoxide by the excess carbon in the time available, and the slightly oxidizing condition, which results, seriously affects the efficiency of the condensation of the zinc vapor to the metallic state. In the past the difficulties arising from these causes have limited practical zinc smelting on an industrial scale to the use of small retorts equipped with small condensers. The retorts had to be small, because a closed refractory container capable of excluding oxidizing gases from the heating chamber surrounding the retort could not be built in large dimensions. The size was also limited because ordinary refractories when thin enough to conduct heat readily are not capable of sustaining a heavy load of charge at high temperature. Moreover, a loose charge of zinc ore and carbonaceous reducing material such as fine anthracite coal or coke breeze is a poor conductor of heat, thus limiting the cross section of the retort. The operation of these small retorts requires arduous

Jan 1, 1937

By W. K. Godfrey

The highest compressive strength cement has the highest bond strength in tests in which the cement is subjected to a confining pressure. After perforating, the bond strength is reduced to nearly zero when the pipe is supported by weak cement. Perforating does not affect the bond strength, however, when the pipe is supported by strong cement. Pipe supported by weak cement is damaged by perforating with expendable capsule jets, but is not damaged by perforating with the hollow carrier gun. High strength cements are recommended for oil wells that are to be perforated. Introduction The purpose of this work is to determine the effect of jet perforating on the bonding strength of oilwell cement at simulated down-hole conditions. Bond strength is a good criterion for determining the effectiveness of cement in performing its main function, i.e., that of isolating zones. According to the literature on the subject, the optimum cement strength for perforating is low and should not exceed 2,000 psi compressive strength. This conclusion was based on the appearance of bullet and jet perforations in neat and gel cements largely done in the absence of a confining pressure more than 15 years ago. Discussion Literature A relatively weak cement has been recommended in the literature as having optimum properties for perforating. In 1947, Oliphant and Farris tested bullet perforating of neat cements at various curing times.' Some of the tests were made at down-hole conditions. They reported that the optimum cement strength for perforating was about 2,000 psi compressive strength. Enlarged holes occurred when strength was too low, and the cement shattered and cracked when the strength was too high. In 1951, Morgan and Dumbauld tested bullet and jet perforating of neat and gel cements at surface conditions.' They reported that optimum cement has a compressive strength less than 2,000 psi. In their tests at atmospheric pressure, high strength cement shattered and cracked when perforated. Thus, the optimum cement strength was based on the appearance of neat and gel cement after perforating. In 1953, Clark showed a relation between cement strength and fluid shutoff.' He concluded that a 500 psi compressive strength is required for good fluid shutoff and that maximum bonding ability is developed at approximately 1,000 psi compressive strength. In 1964, Bell and Shore invalidated most of the conclu sions by the previous authors when they demonstrated that atmospheric pressure tests cannot be used to determine casing deformation and damage that will result from perforating under down-hole conditions.' They showed that the higher the hydrostatic pressure, the more restricted will be the expansion of gases generated by the charge. Less casing deformation and damage occurs under down-hole conditions than at atmospheric pressure. In recent work, Bearden et al. reported that jet perforating at surface pressure with the hollow carrier gun caused the cement sheath to shatter and crack.' The perforating, however, did not seriously affect the pressure required to leak past the casing cement bond. Only three cementing mixtures were tested, and presumably they had strengths in excess of 2.000 psi. Bearden et al. also reported that the hydraulic bonding strength increased as the compressive strength increased. Their hydraulic test showed that approximately 1,000 psi pressure is sufficient to break the casing cement bond for a well aged neat Portland cement sheath. Unfortunately, the tests were not run with a confining pressure, so Bearden et al. were merely measuring the strength of their outer 8%-in. casing. In our investigation, we measured the hydraulic bond strength of cement to pipe under a confining pressure and found that the bond strength was not limited to 1,000 psi. Cement Bond The bond strength is a good criterion for measuring the effectiveness of cement in performing its main function, that of preventing interzonal communication of fluids behind the casing. Measuring bond strength after perforating should be a good quantitative method of determining optimum cement properties, and should be a better method than that used by previous investigators,11 ' who simply observed the appearance of the cement after perforating.

Jan 1, 1969

By Leonard C. Grimshaw

The idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a composite steel. Previous Methods There are two methods in use that result in tolerably good bonds between ferrous metals: (1) the casting method, and (2) what we shall call the "heat-pressure" method. This "heat-pressure" method covers processes in which the bond is made between two prepared surfaces by heating them and then applying pressure. Usually sufficient pressure must be used to produce appreciable spread and elongation, or else we arc merely brazing and not truly welding. Casting methods for welding together ferrous metals have been used more than 74 years, and are described in the technical literature as applied

Jan 1, 1936

By Leonard C. Grimshaw

The idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a composite steel. Previous Methods There are two methods in use that result in tolerably good bonds between ferrous metals: (1) the casting method, and (2) what we shall call the "heat-pressure" method. This "heat-pressure" method covers processes in which the bond is made between two prepared surfaces by heating them and then applying pressure. Usually sufficient pressure must be used to produce appreciable spread and elongation, or else we arc merely brazing and not truly welding. Casting methods for welding together ferrous metals have been used more than 74 years, and are described in the technical literature as applied

Jan 1, 1936

By P. B. Bucky

IN previous publications1 it was shown that a scalar model of any weighty structure, where the stresses produced are mainly due to gravita-tional forces, will behave similarly to its prototype if the model and proto-type material are the same arid the model is placed in a centrifugal field of force (substituted for the gravitational field) which has been increased in the same proportion as the linear model scale is decreased. This principle is now being applied to a study of the behavior of mine structures in an attempt to determine the laws that control them. The importance of using models as a means of solving mining problems has been discussed previously, yet it may be well to reiterate here that this method of research and type of solution have been productive of far-reaching results in other engineering fields, notably those of hydraulics and aerodynamics. Model research is a comparatively cheap and time-saving method of checking practical experience. Up to the present time the best guide to what will happen underground has been the judgment of the man who has observed most and been longest acquainted with the local conditions. His experimental work underground is limited by the elements of cost, time and danger, while failure is seldom permissible. In a model, as in a test tube, all elements that affect the solution of a problem are under definite control. Each element may be varied independently at will and its effects noted. Experimental work on a small-scale model may there¬fore be performed at a comparatively small expenditure of time and money, instead of on a full scale in the mine, where the cost, time, and danger elements are necessarily great. The experiments described in this paper are to be considered as part of a progress report and a continuation of Technical Paper 425. One object of the research program is to make each experiment point the way for further research on that particular phase of the general problem. The results and conclusions presented here are therefore not to be considered as final, but are to be interpreted as

Jan 1, 1933

By Frederic L. Kadey

Diatomite is a siliceous, sedimentary rock consisting principally of the fossilized skeletal remains of the diatom, a unicellular aquatic plant related to the algae. Thus, it has-been formed by the induration of diatomaceous ooze, and consists mainly of diatomaceous silica, a form or variety of opal which is first formed in the cell walls of the living diatom. Diatomaceous silica is not generally regarded as a synonym or the equivalent for diatomite, although it has been so used at various times. Accurately, diatomaceous silica is the preferred name for the principal mineral component of which the rock, diatomite, is composed. The terms diatomaceous earth and kieselguhr are used as synonymous with diatomite. The designations tripoli, tripolite, infusorial earth, etc., were used at one time but are now obsolete. With the changing nomenclature, these terms that were at one time correct when proposed and used for generations would be considered incorrect if used today in the light of current knowledge. The designation diatomite is reserved for those accumulations of diatomaceous silica that are of sufficient quality, size, and minability to be considered of potential commercial value. Processed diatomite possesses an unusual particulate structure and chemical stability that lends itself to applications not filled by any other form of silica. Foremost among these applications is its use as a filter aid, which accounts for over half of its current consumption. Its unique diatom structure, low bulk density, high absorptive capacity, high surface area, and relatively low abrasion are attributes responsible for its utility as a functional filler and as an extender in paint, paper, rubber, and in plastics; and as an anti-caking agent; thermal insulating material; catalyst carrier; and chromatographic support; polish, abrasive, and pesticide extender to name a few representative applications. The United States is the principal producing country, although diatomite is found in numerous other locations.

Jan 1, 1975

By John P. Cosgro

THE increasing use of internal furnace-boilers for mining power-plants (doubtless due to the facility with which they may be installed by reason of their portability; the fact that they require no masonry setting, cast-iron fronts, buck-stays, etc., and practically no foundation; and the successful maintenance of their claim to equal and even superior economy, as compared with boilers of other types) warrants this description of a method of remedying an injury which may occur, to such a furnace, even though it satisfies the requirements of the formula adopted by the U. S. Board of Supervising Inspectors of Steam Vessels.2 I refer to the sagging and deformation which may result from overloading the boilers for a considerable period-say, several days. This is sometimes unavoidable under the exacting conditions of continuous day-and-night service, and (in spite of all rules and precautions, the occasional careless or unskillful work of attendants. Such a trouble is by no means unknown on shipboard, where this type of boiler is so largely employed. In the case here described, two Morrison suspension-furnaces, of half-inch steel, 14 ft. long and 45 in. in mean diameter, with ? dry-back ? boilers, were necessarily operated somewhat beyond their rated -normal capacity for several months, while a third similar unit was -in process of installation, and during this period, though the boilers were kept perfectly clean, heat seems 'to have been generated slightly faster than it was absorbed by, the water in the boilers. The corrugations of this.

Mar 1, 1905

By A. Matsubara

Jan 1, 1922

By A. Matsubara

Jan 1, 1922

By J. T. Crawford

Although nearly 10 pct of the total tonnage of coal produced annually within the United States is handled by bulk freighters on the Great Lakes, very little of the detail connected with it has been published other than occasional newspaper stories and publication of tonnage statistics. Of the total tonnage floated on the Lakes each year some 10,000,000 is stored and distributed from the port of Duluth-Superior, at the western end of Lake Superior commonly known as the Head of the Lakes. This port has the largest single area concentration of coal docks in the world. Since this area contains the largest ore docks, the largest movable material handling bridge, the largest and highest grain elevator and the largest coal bri-quetting plant in the world, it is entirely fitting and proper that here also should be located the largest coal dock and what we believe to be the world's largest clam shell. Of the sixteen coal docks operated by ten companies, five are owned and operated by the North Western-Hanna Fuel Co. which has two docks on the Superior, Wis., waterfront and three docks in Duluth, Minn. It is with these five docks that we are primarily concerned, General History In the summer of 1871 a small sailing vessel entered the harbor of Duluth-Superior with the first commercial coal cargo. All the coal brought up that first year did not amount to more than 3000 tons. During the year 1877 the first dock equipped for handling coal was built in Duluth. Coal receipts increased to 52,785 tons in 1879 the first year for which an official record was kept. Since then the volume of water-borne coal to the Head of the Lakes steadily increased to a maximum of 12,688,321 tons in the year 1923. This tonnage was nearly equalled in the year 1927 and the next highest tonnage recent year was in 1946 when 10,105,703 tons were unloaded. The average annual bring-up over a ten year period 1938 to 1947 was 8,605,231 tons. Approximately 30 pct of the coal unloaded at the Head of the Lakes is handled over the docks of the North Western-Hanna Fuel Co. Competition of other fuels coupled with expansion of coal fields in the mid-west have held coal receipts for Duluth-Superior at a relatively constant figure during the last eight years although the total tonnage of coal floated on the Great Lakes has more than doubled in the past 25 years. From the shovel and wheelbarrow method of unloading early cargoes to the horsepowered windlass derrick with a wooden tub was but a short step. The first movable coal handling, steam operated,

Jan 1, 1949

By J. Volney Lewis

The following paper is based chiefly on work done for the North Carolina Geological Survey, and is presented here by permission of Professor J. A. Holmes, State Geologist. It represents, in a very general way, the field-results obtained during the summer months of 1893, and 1894, and part of 1895; and the portions pertaining to North Carolina are, to a certain extent, abstracts of a report shortly to be published as Bulletin No. 11 of the State Survey. Less emphasis, however, is here laid on the petrographic descriptions of the peridotites, and more detailed treatment is given to subjects pertaining to methods of mining, cleaning, and utilization of the commercial product, corundum. Some of the most extensive fields for investigation which this subject presents have been scarcely more than suggested.

Jan 1, 1896

Jan 1, 1900

By P. D. Frost, H. A. Robinson, J. R. Doig, M. W. Mote

The mechanism of hardening in heat-treatable zirconium alloys was foUNd to be analogous to that for titanium alloys. Zirconium containing a relatively large addition of a ß -stabilizing element such as molybdenum or columbium can be hardened by the following transformation: Lean alloys, having insufficient alloy content to retain ß at room temperature are hardened by the following transformation: Application of these findings in Zr-Mo-Sn and Zr-Nb-Sn alloys produced strengths as high as 190,000 psi with reasonable ductility. PRIOR research on zirconium alloys has been concerned with development of greater strengths and creep resistance by solid-solution hardening or by dispersion hardening. Although solution and aging heat treatments had been applied earlier to zirconium alloys, quenching frequently produced low ductility. The possibility that the ß-to-w transformation, discovered earlier in titanium alloys,' might also occur in zirconium alloys and cause low ductility was considered, and, indeed, was found as predicted2 to be the case. In the earliest experiments, the heat-treatment response of titanium, too, was disappointing. However, by avoiding the formation of the embrittling w phase, it became practical to obtain room-temperature strengths higher than 180,000 psi, with elongation values of 10 pct.3 Based on the present concept of titanium heat treatment, the principal requirement for a heat-treatable zirconium alloy is that it contains a certain minimum amount of one or more ß -stabilizing elements. Only molybdenum, columbium, and tantalum, when present in sufficient amounts, are known to stabilize ß zirconium to room temperature during rapid cooling from the ß field. Tantalum was undesirable because of its high thermal-neutron cross section. Aluminum and tin are effective a stabilizers, but aluminum has been shown to seriously decrease the corrosion resistance of simple zirconium alloys in hot water. Therefore, for the present study, tin was used as the stabilizer addition. The alloys selected for this evaluation are presented in Table 1 along with their analyses and ß-transus temperatures. The analyses indicated that intended compositions were usually realized. EXPERIMENTAL PROCEDURES All of the alloys were melted from sponge zirconium and fabricated to sheet for heat treatment

Jan 1, 1960

Jan 1, 1970

By R. J. Stevens

THE Roan Antelope Smelter commenced operations in October, 1931. As originally designed, its equipment consisted of one reverberatory furnace, 120 X 25 ft, two Peirce-Smith converters 12 X 20 ft, and one straight line casting machine. Since that time the following additions have been made: One reverberatory furnace 120 ft X 28 ft (1934) One reverberatory furnace 95 ft X 28 ft (1943) Two 12 X 20 ft Peirce-Smith converters (1934 and 1938) One 13 X 30 ft holding furnace 6 (1938) One straight line casting machine and 2 ladle tilting quadrants (1934) The metallurgy of the smelting process is comparatively simple. However, there are several features of operation which are uncommon to most copper smelters: (1) The high grade of concentrate treated; this has always been about 50 pct copper. (2) The high flux burden on the charge. This is necessary because of the deficiency of bases'in the concentrate and the high alumina content of the concentrate. (3) The frequent necessity of adding coal to the furnace charge to control the matte grade. (4) The high grade of matte produced. This has led' to unusual converter problems. From the commencement of operations, the ore mined has come from the Roan Basin orebody. The concentrate produced from this ore consists mainly of chalcocite and shale with small proportions of other copper minerals. As mining operations extend to the Roan Extension orebody, the proportions of bornite and chalcopyrite in the concentrate will increase with a corresponding decrease in the copper content of the concentrate. Because of the concentrate grade the capacity of the reverberatory . furnaces in terms of tons of copper produced per ton of coal burned is high.. This ratio is usually over 2.2, and on especially favourable runs has reached 2.6. Reference to Table , shows that the iron content of the concentrate is unusually low. Only part of this iron is available for slag formation, the balance going to the matte. To make up this deficiency in bases, limerock is added to the furnace charge. This flux ensures a slag that is of the correct silicate degree, is sufficiently fluid, of low specific gravity, and it counteracts the thickening effect of the alumina present. An ample supply of flux is obtainable from Ndola, 2 2 miles distant by rail. Although the reverberatory slag has a high copper content, the slag fall is low and the copper loss in the slag now rarely exceeds 1.0 pct of the total copper charged. The blister copper shipped is of such purity that only one fire refining operation has been necessary to produce a wirebar with properties comparable to electrolytic copper. Bismuth has always been the most troublesome impurity and consequently the problem of its control in the finished product has been of prime importance. Practically none is removed in the reverberatory furnace. The bulk of the elimina-

Jan 1, 1947

By Kirtland Marsh

THE manufacture of gas masks by the Chemical Warfare Service, U. S. A., required preparation of the carbon used in the canisters. The largest plant for the production of this carbon was situated at the works of the Astoria Light, Heat and Power Co., at Astoria, N. Y.; this paper will deal1 with the pyrometry equipment at that plant. Commercial charcoal was found unsuitable for use in gas masks because of its low power of absorption and its poor resistance to abrasion. The best raw material for the production of carbon was found to be coconut shells, but any kind of nut shells or fruit pits were used when sufficient quantities of coconut shells could not be obtained. The shells were first carbonized in retorts, the carbon was then crushed and screened between 8 and 16 mesh, and finally submitted to a special heat-treatment in air; steam treatment was later substituted for treatment in air. The production of gas-mask carbon on a commercial scale was begun at Astoria about Aug. 1, 1917. Temperature control was essential during the initial carbonization of the shells, as well as during the air or steam treatment, and pyrometers were installed for this purpose. The installation and maintenance of all pyrometry equipment was done by the pyrometry department, consisting of an officer in charge, an assistant, and two men. A special pyrometry laboratory was maintained in which all repairs were made.

Jan 9, 1919

By B. Kopelman, C. C. Gregg

THE reduction of tungstic oxide to tungsten metal powder by hydrogen is a process by which one might expect the resultant metal powder to he porous. In- deed, sponge iron, prepared by rcduction of the oxide in a reducing gas, is generally accepted as quite porous. with pores large enough to be seen readily under the optical microscope at relatively low magnifications. However, any pores that may exist in tungsten metal powder are not resolved by the optical microscope, and apparently, not even by the electron microscope. Fig r shows commercial tungsten powder magni- fied at I0,000 X by the electron microscope,' both etched and unetched. In an earlier paper by one of the authors,* the existence of ports in tungsten powder was required to explain adequately the particle size changes occurring during the reduction of tungstic oxide. The inability to detect these pores under the electron microscope at 10,000 X implies that these {pores} are of a size of 100 A units or less. (This in itself is by no means proof that pores above 100 A would not exist, since polishing effects on the specimen might smear up holes of such small magnitude). If, then, these pores are less than IOO A. and of the order of molecular size, then the density of the metal powder should be

Jan 1, 1949

By Howard N. Eavenson

From the Pittsburgh coal bed in the four states of Pennsylvania, Ohio, Maryland and West Virginia has been produced an output that, at mine prices, represents a greater value than any other single mineral deposit in the world has yielded.12 While this distinction may in a few years pass to the gold reef of the Witwatersrand, it is possible that eventually, owing to the tremendous reserves still remaining, the ultimate yield of the Pittsburgh bed will be greater than that of any other known single deposit. Considering its importance, not a great deal has been written of its early history and development as a whole; most of the accounts have been of limited localities, or, at the most, of the area within a single state. In "Coal through the Ages" the writer mentioned some references to its early history, but this study will deal not only with its history but with the character of the bed, where and why it was first developed, and its effect upon the states in which it is found. It has not been the intention to write a detailed history of the development of the seam in each locality, as neither time nor inclination were available for doing such work, but only to show the influences that tended to hasten or retard such development. In general the historical matter ends about 1830, when geological surveys began to be made. Some of the maps show data available only since that time, and the sections about coal preparation and coking have been extended to the present time to show the changing conditions. It is believed that the early history includes all published records, and many more sources than those shown in the bibliography were consulted. It is quite likely that some references to coal in this area may be found in the unpublished papers of some of our early soldiers and colonizers, which exist in several libraries, and it is hoped that some future * Dedicated to Dr. Thomas S. Baker, President Emeritus, Carnegie Institute of Technology, whose labors in promoting the International Coal Conferences and in establishing the Coal Research Laboratory have done much in showing the industry how science can be of help to it. Manuscript received at the office of the Institute Feb. 15, 1938.

Jan 1, 1938

By Howard N. Eavenson

From the Pittsburgh coal bed in the four states of Pennsylvania, Ohio, Maryland and West Virginia has been produced an output that, at mine prices, represents a greater value than any other single mineral deposit in the world has yielded.12 While this distinction may in a few years pass to the gold reef of the Witwatersrand, it is possible that eventually, owing to the tremendous reserves still remaining, the ultimate yield of the Pittsburgh bed will be greater than that of any other known single deposit. Considering its importance, not a great deal has been written of its early history and development as a whole; most of the accounts have been of limited localities, or, at the most, of the area within a single state. In "Coal through the Ages" the writer mentioned some references to its early history, but this study will deal not only with its history but with the character of the bed, where and why it was first developed, and its effect upon the states in which it is found. It has not been the intention to write a detailed history of the development of the seam in each locality, as neither time nor inclination were available for doing such work, but only to show the influences that tended to hasten or retard such development. In general the historical matter ends about 1830, when geological surveys began to be made. Some of the maps show data available only since that time, and the sections about coal preparation and coking have been extended to the present time to show the changing conditions. It is believed that the early history includes all published records, and many more sources than those shown in the bibliography were consulted. It is quite likely that some references to coal in this area may be found in the unpublished papers of some of our early soldiers and colonizers, which exist in several libraries, and it is hoped that some future * Dedicated to Dr. Thomas S. Baker, President Emeritus, Carnegie Institute of Technology, whose labors in promoting the International Coal Conferences and in establishing the Coal Research Laboratory have done much in showing the industry how science can be of help to it. Manuscript received at the office of the Institute Feb. 15, 1938.

Jan 1, 1938