Search Documents

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

By J. L. Byers

THE metals of the platinum group, ruthenium, rhodium, palladium, osmium, iridium and platinum, have certain characteristic effects on the structure and appearance of the cupellation bead. These effects are dependent not only on the particular member of the group present, but also on its concentration. The extent and quality of these effects, however, have not received investigation worthy of their importance. Bannister and Patching investigated the qualitative effects of some of these metals in 1913. This paper deals with a possible rapid qualitative and quantitative delineation of the effects exerted on the cupellation bead by the various metals in the platinum group. More particularly, the paper correlates quantitatively the presence of such metals with their characteristic structural and surface effects. Inasmuch as the various members of the group are more frequently associated with gold than with silver, the gold button will receive the greater consideration. The past two decades have seen a much greater interest manifested in this particular group of metals, because of the increased industrial demand for them. There has been a constantly growing need for assays that will not only express the silver and gold values but also indicate the presence of the other metals. If these indications could be used as quantitative criteria, their value would be greatly increased, because the methods of chemical analysis for the elements of the platinum group are lengthy, involved and unreliable except when the analysis is made by an expert and experienced rare-metal analyst. The materials for the X-ray diffraction examination of the different beads were prepared by filing and screening to -200 mesh, and were then rayed in a General Electric X-ray diffraction unit. The filed samples were treated magnetically in order to eliminate any possible steel particles. Sodium chloride and C.P. gold and silver were used as standard comparators.2 (See Table 1.)

Jan 1, 1932

By R. W. Shoenberger, J. D. Clendenin, W. L. McMorris, N. Schapiro, B. R. Kuchta, A. A. Terchick, R. J. Gray, J. G. Price

INTRODUCTION * The United States is fortunate in having enormous reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by palynology,** stratigraphy, paleontology and petrography are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining (1) the economic justification for mining the coal, (2) the optimum design of the preparation plant and (3) the most effective use of the coal. Fortunately, the cost of mining coal has remained stable because of better mine planning, more efficient operations and increased mechanization of mining operations. However, increased mechanization raises the amount of impurities in the coal mined, and this requires more and better coal beneficiation to meet the more stringent quality requirements set by the market. Besides, mechanical miners also produce relatively fine coal and, to ensure maximum liberation of impurities, much of the coal presently being used must be crushed to a finer size prior to preparation. The bulk of all coals presently used in this country is mechanically cleaned, much of it at a lower specific gravity than in the past. This necessitates the use of new and improved processes and equipment for coal washing and recovery, such as heavy-medium cyclones and vessels, and froth flotation cells. However, because wet-cleaning processes are pre- dominant in the United States and fine coal retains large amounts of moisture, the increased production of cleaned fine coal accentuates the need for new or improved methods and equipment for dewatering and drying this coal. The larger amounts of coal being beneficiated and the use of new and improved beneficiation processes will aid in controlling and ultimately eliminating sources of pollution. Modem coal markets demand coals that meet rigid specifications. Most coals are purchased under contracts that specify moisture, ash, and sulfur contents, or heating value, depending upon the end use. There has also been a growing trend toward specifying other properties, including particle size and coking capability. These specifications may include not only the * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. ** Palynology is the study of plant microfossils, especially spores, pollen, and other types of fossils not usually studied by paleontologists.

Jan 1, 1968

By W. S. Ayres

The construction of a new breaker at the Cranberry Colliery, Hazleton, Pa., was forced upon the operators, A. Pnrdee & Co., by a fire which destroyed the entire plant early in January, 1896. The loss included, in addition to the breaker, three boilerhouses and three engine-houses. The boilers were not injured, but the steam-pipes and connections were all broken and warped by the fire. The boilers were probably saved from injury by the presence of mind of the fireman., who started all his feed-pumps and filled the boilers with water. The hoisting-engines were more or less warped and cracked, but by patching and replacing the injured and broken parts, they were made to do satisfactory service in the new plant. It may be worthy of mention that the wrought-iron shaft of one of the hoisting-drums, 12 inches in diameter by 17 feet long, was so heated in the fire that the weight of the drum caused it

Jan 1, 1899

By B. H. Kear, S. M. Copley

A dynamic theory of precipitation hardening in alloys containing cohevenl, stvess-.free, ordered particles is developed. The yield stvess is predicted from the stress dependence of the plastic strain vale, which is related to a derived dislocation velocity-stress function. The theory is shown to predict the magnilude and temperature dependence of the yield stress of a commercial nickel-base superalloy as well as many details of its slip structure. GLEITER and Hornbogen have developed a theory of the yield stress in alloys hardened by coherent, stress-free ordered ptrticles based on the observation that dislocations (b = a/2 (110)) glide in pairs.' When a dislocation pair shears through an ordered particle, the glide motion of the leading dislocation is impeded since it must create antiphase boundary (APB), whereas the motion of the trailing dislocation is assisted because it annihilates APB produced by the first one. Taking into account the APB energy, the size, and spacing of the particles, G-H predict the observed yielding behavior in Ni/18.8 Cr/6.2 A1 alloys composed of a matrix phase y '(nickel-solid solution) and particles of y' (basically Ni3A1). The G-H theory, as well as all previous theories of hardening by coherent ordered particles, do not include the details of dislocation motion; the present dynamic theory is an attempt to overcome this limitation. In the dynamic theory, the yield stress is predicted from the stress dependence of the plastic strain rate, which is related to a derived dislocation velocity-stress function. This function can be evaluated if the structure of the alloy, the APB energy of the ordered phase, and the characteristic drag or frictional stresses of the matrix and precipitate phases are known. The theory is shown to account for the observed temperature dependence of the yield stress in a commercial nickel-base superalloy. 1) NICKEL-BASE SUPERALLOYS Although their compositions are complex, the nickel-base superalloys have remarkably simple structures. A detailed examination of the commercial superalloy

Jan 1, 1968

By N. J. Themelis, P. Spira

The efficiency of the reverberatory furnace operation in producing. slags of 1020 copper content depends on the mixing and flow conditions in the bath. Radioactize-tmcer tests have indicated the jkaction of bath volume engaged inflow and the mixing conditions in the bath. The factors controlling the flow pattern of slag have been classified as laminar transfer flow, natrsral convection, and flou, due to the rapid addition or removal of slag.. Similarity criteria for model studies have been developed. The pyrometallurgical processing of copper begins with the smelting of either flotation concentrates, or direct-smelting ores which have been partially roasted to calcines. These materials are generally smelted in a reverberatory furnace, Fig. 1, and separate into two liquid phases, a sulfide matte and an iron silicate slag. he matte is tapped and subsequently reduced to metallic copper in a converter, while the reverberatory slag is usually discarded without any further treatment. Molten slag from the converting operation is returned intermittently to the reverberatory in order to recover its high copper content (1 to 3 pct Cu). The reverberatory furnace is about 115 ft long by 30 ft wide. In general, the solid charge is fed at intervals through openings along the sides of the roof and forms sloping banks from which the molten materials trickle down into the bath; the charge banks extend over a length of about 70 ft from the firing wall. The depth of the slag and matte layers varies from smelter to smelter; in the Noranda furnaces, the slag depth is 24 to 30 in., while the depth of matte at the taphole is about 20 in. Apart from smelting, the functions of the reverberatory are to recover most of the copper content in the converter slag by physical and chemical interaction with the furnace bath, and to provide adequate time for optimum separation between matte and slag. The efficiency of these operations depends on the mixing and flow conditions in the bath and is reflected on the copper losses in the slag. In the present study, the reverberatory furnace is considered as an open-channel chemical reactor and the driving forces for material transport through the bath are examined by means of flow and mathematical models. FLOW CONDITIONS IN THE REVERBERATORY FURNACE To facilitate the study of mixing conditions in continuous-flow reactors, two idealized patterns of flow have been accepted by workers in this field.' The term "backmix" flow is used to describe complete and instantaneous mixing in the reactor (perfect mixing); all particles have the same chance of leaving the system, independently of their time of entrance, and the fluid is uniform in composition throughout the vessel. On the other hand, "plug" flow, or "piston" flow, assumes that a fluid element moves through the reactor without overtaking or mixing with fluid entering at an earlier or later time. In addition to the two idealized patterns of flow, "deadwater" flow accounts for that portion of the fluid which is moving so slowly that it may be assumed to be stagnant. According to the definition by evensppiel,' the cut-off point between active and stagnant fluid may be taken as material which stays in the vessel for a period twice the mean residence time. The flow patterns in real vessels may be approximated by a combination of the above flows. Thus, the vessel is assumed to consist of interconnected flow regions with various modes of flow existing between them. The flow pattern may be determined directly from the flow paths of fluid through the essel. -However, the difficulty of obtaining and interpreting such information has led to the alternate approach of determining the residence time distribution of fluid elements by means of stimulus-response studies. The stimulus is provided by introducing a tracer in the inlet stream and the response by the record of the change in tracer concentration in the exit stream from the reactor. Such tests have been conducted in glass tank furnaces using either chemical7"9 or radioactive tracers1'-'' and, in one case, experiments have been reported for a metallurgical furnace.'"

Jan 1, 1967

By J. W. Bolton

PRODUCTION of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical.

Jan 1, 1929

By Mark J. Klein

The precipitation of nitrogen in quenched and aged CY-35 at. pct Re was followed by internal-friction and electrical-resistivity measurements. It is shown that the precipitation kinetics of nitrogen from solution are many orders of magnitude lower in this alloy than in chromium. The reluctance of nitrogen to precipitate from sol~ction can be attributed to the composilional r-eadjustnzents required in the z.icinity of a chromium nitrade particle for gowth to occur. AS part of an investigation of the mechanism by which rhenium increases the low-temperature ductility of chromium and other Group VI-A metals, it was of interest to compare the concentration of interstitial elements retained in solution in chromium with that of a ductile Cr-Re alloy. The presence of certain interstitial elements in chromium has been shown to decrease its ductility1-5 and, of these interstitials, nitrogen is believed to have the most detrimental effect on mechanical properties. Thus, a comparison of the disposition of nitrogen in chromium with that in a ductile Cr-Re alloy might provide information about the mechanism whereby rhenium enhances the ductility of chromium. In previous internal-friction studies it was shown that the equilibrium solubilities of nitrogen in chromium and Cr-35 at. pct Re did not differ greatly.= However, results indicated that the actual concentration of nitrogen retained in solution at ambient temperatures is likely to be considerably greater in the alloy than in chromium because the precipitation kinetics of nitrogen are greatly retarded by the addition of rhenium. The objective of this investigation was to study the kinetics of nitrogen precipitation in Cr-35 at. pct Re in greater detail and to obtain information concerning the mechanism of nitrogen precipitation in this alloy. The properties studied were internal friction and

Jan 1, 1967

By D. Murgue

The circulation of air in underground workings is subject to a gradual and continuous reduction of its pressure, from intake to outlet, caused by the friction between it and the more or less rough and uneven surfaces of the passages. For comparison with the flow

Jan 1, 1894

By F. Forscher

Pronounced porosity, decreasing with distance from the fracture surface, is found in the necked region of tensile specimens tested at room temperature or liquid nitrogen temperature. A hydrogen solution treatment followed by a quench prevents pore formation in tests at —196°C, but has little effect on tests made at room temperature. Reduction of area values at —196°C are strikingly improved by the same treatment, but show no improvement in room temperature tests. The experimental results support the hypothesis that strain-induced porosity results with hydride initially present or, in material containing less than 50 ppm H, with hydride precipitated by strain aging. ZIRCONIUM'S advent as an engineering material in nuclear reactor construction has brought forth many investigations concerned with the properties of this metal and its alloys. Some attention has been given to the ductility of the metal.1, 2 Particularly, the effect of hydrogen on the impact strength was noted," indicating a pronounced dependence of ductility on the hydrogen content and its distribution in the metal. Micro graphic:' and X-ray diffraction studies' have shown that a precipitated hydride phase causes embrittlement in zirconium,' which implies a distinctly different mechanism from that causing hydrogen embrittlement in steels."-' In the latter case, it is assumed that atomic hydrogen diffuses to rifts, where it forms molecular hydrogen under such internal pressures that it causes the rifts to enlarge, leading to fracture. Thermo-dynamic studies of the Zr-H system8, 9 also indicate that the internal pressure of molecular hydrogen would be too low to cause any damage to the zirconium at room temperature, and the formation of a zirconium hydride (d phase) is favored." It is noteworthy that this phase has a face-centered-cubic structure and nearly 18 pet larger molar volume than close-packed-hexagonal a-zlrconlum' Other features of the ductility of zirconium are the absence of a typical cup-cone failure upon tensile testing, a pronounced strain-induced porosity in the necked region of a tensile bar, Fig 1, and the associated spongy appearance of the fracture surface A tremendous improvement in ductility at liquid nitrogen temperature can be observed following a heat treatment that retains the commonly present quan- tities (10 to 50 ppm) of hydrogen in solution. Such tests show a typical cup-cone failure and the absence of strain-induced porosity, Fig. 2. The present paper reports results of an investigation into the causes of strain-induced porosity in zirconium. Room temperature tensile fractures of mild steel, aluminum, and titanium have also been examined for strain-induced porosity. In each case porosity could be detected, but the amount was orders of magnitude less than was found in zirconium. Of the three metals, titanium showed the strongest effect. Material, Specimens, and Preparation The greater part of this investigation was done on Westinghouse crystal bar zirconium, are-melted, forged, and hot-rolled. Chemical analyses of the hot-rolled plates are given in Table I, along with those of the Foote crystal bar zirconium used in this work. The specimens were machined from the hot-rolled plate (1550°F) of 1/2 in. thickness and subsequently heat-treated according to one of the treatments shown in Table IS. All specimens were machined round, the longitudinal axis in the rolling direction, with a gage

Jan 1, 1957

By G. S. Cole, G. F. Bolling

Fluid flow strongly influences ingl structure and the columnar -to-equaaxed transition. Artificial flow patterns siwzilar to the nuturul ones act to induce this transition, while dampening forces act to suppress this transition. It is shown here how simple mechanical forces can be applied to a systerrz in order to induce or slipPvess relative fluid flow and the change both the structure transition and the exact structures obtained. The example used is the effect of slow rotations and oscillations 012 a cooling- ingot (of laboratory scale). The details of rotution and oscillation for various cooling rates, lenlperal~ire gradients, and sizes of ingot are related to other solidzfication variables. THE grain structure of a casting can be changed by altering the fluid motion during solidification. Just how important these changes are depends directly upon the degree to which the fluid motion can be controlled. An early step in understanding the nature and influences of fluid motion was taken by studying natural thermal convection; when a static mechanical device was used to suppress natural flow the result was opposite to that obtained when an electromagnetic device was used to augnlent flow in a pattern similar to the natural one. ''2 Suppression allowed more columnar growth to occur, but "augmented natural convection" brought about an earlier columnar-to-equiaxed transition (CET). Since the solidification of a free ingot must have characteristics somewhere between those displayed during suppression and augmentation, we know that natural convection must influence the CET. Further, since heat transfer in the liquid is always some time-dependent combination of convection and conduction, it can easily be guessed that the temperature gradient in the liquid is the vital factor affecting the CET.1,2 It is obvious that the structure arising from the unadulterated solidification of an ingot, without external influence, is rarely if ever the best possible one. Although the pattern of the natural fluid flow may be considered efficient, the magnitude of the flow and the heat transfer decrease freely from the outset. For a

Jan 1, 1968

By E. Houdremont, H. Schrader, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By H. Schrader, E. Houdremont, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By Sylvan Cromer

THE need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investi-gators1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happen-ings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quanti-tative results for air-water flow. EXPERIMENTAL APPARATUS AND PROCEDURE The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1939

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By J. F. Kemp

Introduction The Bulletin of the Institute for March, 1911, is chiefly devoted to papers upon the iron ores of northeastern Cuba. At that time information about the new developments in the peculiar brown hematites of the region was becoming widely circulated and interest was especially keen. For some years exploration had been conducted with pits and trenches and so great an area had been shown to contain ore in the Mayari, Moa, and Cubitas or San Felipe districts, that the reserves conveniently situated for the consumption of American furnaces were estimated as quite two billions of tons. In the subjoined footnote will be found a list of the principal papers of special interest which have already been published.1 The further remark may, however, be made that the

Jan 2, 1915

By D. M. Dunbar, H. C. SCHLILTZ

HE Chile Exploration Co.'s mine and reduction plant are at Chuquicamata, Chile, on the eastern edge of the Atacama Desert, 163 miles northeast of Antofagasta, 80 miles from the Pacific Ocean, and 70 miles from the Bolivian border and at an altitude of 10,000 ft. Guggenheim Brothers started prospecting in -4pri1, 1912, and purchased the main property, in October of that year; the property is now controlled by the Anaconda Copper Mining Co., which acquired it in January, 1923. The orebody strikes north 10" east, and has a dip of about 64" west. The length, as far as developed, is approximately 1% miles; the width averages sightless than mile.

Jan 1, 1925

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems.

Jan 12, 1957

By G. Willard Quick

FAILURES in railroad rails have been of vital concern to engineers; railroad executives, rail manufacturers and the general public for years. Failures from transverse fissures originating from internal nuclei have received particular attention in the past 20 years. Dr. J. E. Howard first reported this type of failure in 1911, as being responsible for a wreck-on the Lehigh Valley R. R. in which several lives were lost. Since then many transverse fissures have been found. In 1919, Waring and Hofammann1 etched longitudinal sections of rails in hot acid and found cracks extending both longitudinally and transversely in certain used rails as well as in some new rails.. Since then it has been thought by many that these "shatter" cracks are the nuclei from which transverse fissures subsequently develop in service. Methods for reducing the rate of cooling rails on the hot. bed have been devised to decrease the temperature gradient and consequently the stress gradient in the rails. A study of the tensile properties of rails at elevated temperatures was made by Freeman and Quick,2 who investigated the properties at temperatures through which rails pass on the cooling bed after leaving the hot saw. In their investigation a special study was made of the ductility of the steels in the temperature range 400° to 700° C. In this temperature range it was found that certain rail and other steels showed a marked decrease in elongation and reduction of area. The phenomenon was called "secondary brittleness" and the temperature range the "secondary brittle range." A tentative explanation was presented that internal failure such as "shatter cracks" and "hair cracks" in rails are the result of thermal stresses developed in the steel structure while cooling through the secondary brittle range. The investigation showed that the magnitude of the phenomenon varies for different heats, but that it did not differ for specimens from different ingots or for different rails in a particular ingot. It was also shown that annealing rail steel at a temperature either above or below the critical

Jan 1, 1932