Search Documents

By B. Zondek, W. T. Cardwell, J. W. Sheldon

The fundamental equations that are used to describe two-phase fluid flow in porous media are Darcy's law for each phase and an equation of continuity for each component. The special case of one-dimensional, incompressible, two-phase flow has received much attention in the petroleum engineering literature.1-10 The basic paper on the subject is that of Buckley and Leverett.2 Buckley and Leverett showed that one could eliminate the pressure and obtain a single partial differential equation for the saturation. They solved this equation for the case when gravity and capillary forces are negligible. A frequently encountered property of the solution of the basic partial differential equation is that, as time progresses, the saturation becomes a multiple-valued function of the distance coordinate, x. Buckley and Leverett interpreted the formation of multiple values as an indication that the saturation-distance curve had be-come discontinuous. They developed a method of determining the position of the discontinuity from a material balance. We solve the Buckley-Leverett partial differential equation using the method of characteristics and the concept of shocks. Our treatment is analogous to treatments used in the theory of supersonic compressible flow." Although the numerical results obtained are the same as those obtained by previous methods, we believe that this approach is more logical and has broader applicability. It can, for example, be generalized to treat the case when the fluids are compressible. It is not clear how one would go about doing this using the method of Buckley and Leverett. To illustrate the power of the method of characteristics with shocks, we solve a problem in gravity segregation which has not been treated previously in the literature. A special case of the general method developed here was used by Welge, to solve a particular fluid displacement problem. We consider two-phase incompressible flow along the vertical direction x in a porous medium. We assume that there is no flow transverse to .x. We measure positive in the upward direction. The fundamental equations are obtained from Darcy's law and the mass conservation law. Since the two phases are incompressible, mass conservation is equivalent to volume conservation.

By Gerhard Derge

The rapidity of oxygen steelmaking has created renewed interesl in the mechanisms and kinetics of the various processes involved. These studies can now be approached with increased confidence because of the more adequate thermodynamics, physical chernislry, and relevant engineering infornzation available. These combine to offer promise of useful control and automation if the details of each specific problem can be sufficiently well-defined. The hot filament microscope provides new insig-hi into many of these problems by direct observation at temperature, allowing the appraisal of the relative importance of thermal gradients, convection, and intermediate phases. All of these have a direct bearing on the overall rates and control of most pyrometallurgical processes. It is one of the special privileges of the Howe Lecturer to become better acquainted with this distinguished man. All of us interested in the metallurgy of iron and steel have developed some sense of his widespread influence by the annual reference to his work in these Memorial Lectures. Each lecturer since 1923 has been able to identify his personal specialty with the broad interests of Professor Howe. This has become even more rewarding with the background information from Professor Gensamer's monograph, "Henry Marion Howe's Contributions to Metallurgy, which brings out his happy combination of intellectual and professional activities. Beyond this, I found my personal bond with Professor Howe in his book on The Metallurgy of Sleel first published in 1891.' After a detailed discussion of the dephosphorizing action of slags, he relates the mineral species identified in the frozen sample to the chemistry of the fused slag with the question, "Is it not most philosophic to hold that these independent entities were wholly integrated in the initial magma; that their presence in it was wholly

Jan 1, 1968

By L. O. Bieber, L. H. Martin

DIFFERENT MELTS OF THE same type of nickel and high-nickel alloys, while having almost identical mechanical properties at room temperature, may have widely varying hot malleability. Either the upper limit or burning temperature may vary or a variation in malleability may occur within the temperature limits normally encountered during hot working. Melts which have reduced hot malleability of the latter type, are said to have a "hot short" range. Examination of melting records and chemical analysis of these heats fails in most cases to show the reasons for these variations. In May, 1930, an investigation was started to determine if a quick and accurate method of hot-malleability testing could be developed which would predict the ability of the metal to withstand hot forging and hot rolling by standard mill practices. The results obtained were so satisfactory that from that time on, all melts of nickel and high-nickel alloys produced in the International Nickel Company's Huntington, W. Va. Works have been tested when hot malleabilty was an important factor. To date, over 63,000 commercial melts of Monelt † nickel, Inconel† and other high-nickel alloys have been tested and the test data compared with processing results. As the result of experience gained in over sixteen years, two standard methods of hot malleability testing have been adopted.

Jan 1, 1948

By H. S. Geismer

INTRODUCTION. THERE are three general methods available for obtaining commercial brown iron-ore : hand-screening; washing; and washing and concentrating. Hand-screening has produced a large tonnage of ore in the past, but is rapidly falling into disuse, except as a preliminary step, largely because modern furnace-practice requires all foreign material to be separated from ores before they are delivered to the furnace, and hand-screened ores can rarely be made to fulfill that requirement. Another argument against hand-screening is, that the waste-pile often contains as much ore as the screen recovers. The operation known as hand-screening consists of throwing the ore-bearing material against a stationary inclined screen of 0.5- to 0.75-in. mesh, similar in construction to the screens employed in sand-pits. The recently-prospected brown-ore deposits of Cuba seem to offer possibilities for hand-screening not possessed by the average American deposit, since these ores are not associated with worthless clays. Washing, and washing and concentrating, may be discussed together, since concentrating is never practical on brown iron-ore, except to treat ores that have already been washed. (Strictly speaking, washing might be classed as concentrating, but it is never so designated by brown-ore men.) The various steps of removing ore-bearing material and converting it into ore suitable for blast-furnace use, may be grouped under five heads: loading for transportation ; transporting ; feeding into the washer; washing; and concentrating. These five subjects will be considered in consecutive order. Each of these successive steps may be accomplished in a number of different ways, the choice depending entirely upon the character of the ore-bearing material to be treated.

Aug 1, 1911

By R. A. Davidson, L. Silverman

RESIDENTS of many urban centers are becoming increasingly aware of the obscuring effect of fume and smoke discharge from power, metallurgical, chemical, and other industries; and they, as well as the legislatures of these affected cities, are agitating for cleaner air. Management's most pressing problem is to find an economical way to reduce process effluents in response to the growing pressure from population and legislative demands. The removal must be done, if possible, without handicap to the current operation, since the costs of relocating are often excessive or prohibitive. In fume recovery or disposal, an important item to consider is whether or not the material being discharged has any value. If it has commercial value, the cost of its recovery may offset or aid amortization. For this reason, in making a study of the specific problem in hand, a major factor was the nature of the material emanating from the stack: in particular, its particle size, size range, and its chemical and physical composition, as well as its potential value and utility when recovered (in either a wet or dry state). Should the product have no commercial value, it must be disposed of at minimum cost in a way to prevent recontamination. Initial studies were therefore made to determine stack concentrations and volumes of material evolved from the operations. The next phase of the study concerned the physical and chemical nature of the collected fume. The third portion of this paper describes the wet and dry collector studies undertaken to recover the fume. Cleaning Requirements for Ferroalloy Furnace Operation The basic need for any effluent collection equipment is the highest possible efficiency and the lowest tolerable resistance when the power consumption involved is considered. Since the electric furnace effluent is largely composed of fume of small size (less than 0.5u), it has high light obscuring properties, and even low concentrations will cause some loss of visibility and be evident to nearby residents. The permissible limit for fly ash emission in many cities is based on a weight value (viz, approximately 0.4 grains per cu ft), but the smoke density values are dependent upon a shade of color. In the case of the Los Angeles County code, emission is restricted to pounds per pound of material processed per hour basis (but not exceeding 40 lb per hr for any one given plant operation). If an average particle size of the fume from ferro-silicon alloy electric furnaces is assumed to be 0.4u (as shown later, this is the approximate mean size) and an average loading of 1 grain per cu ft (stp), each cubic foot of stack gas will contain approximately 75x10 10 particles (based on assumed, and confirmed, spherical shape and a standard deviation of unity). When it is realized that the air in metropolitan areas, which are also general industrial areas, contains approximately 5x108 particles, the tremendous light scattering effect of this concentration becomes apparent. Consequently, nearly 100 pct collection would be necessary to equal the average concentration. Fortunately, however, discharge from a high point above ground (50 to 100 ft) will result in at least a thousandfold dilution, or the stack concentration reaching the ground in the foregoing case might result in a ground concentration of ' particles. If the concentration at the source could be reduced by a factor of 100 (99 pct efficiency of collection), then a concentration of 75x10" particles would be diluted to 7.5x10' which would be very satisfactory. An efficiency of 90 pct (factor of 10 decontamination) at the source would result in a discharge of 75x109 articles which upon dilution yields 75x10 which is still 15 times the general air value. Another approach to this consideration is to use the value of concentration of 0.005 grains per cu ft for the value of a visible effluent as cited by Kayse.1 To attain this value with an average loading of 1 grain per cu ft would require an efficiency of 99.5 pct. Since the foregoing value is not based on any reported size of fume particles, it is felt that the numbers' approach given previously is more reliable. These calculations serve to indicate the desirability of thorough cleaning, preferably at the source, and with efficiencies well above 90 pct, preferably above 95 pct (dilution 1:20). One of the most important items in any control program is to reduce the concentrations as close to their sources as possible. The use of better furnace design, deeper coverage over the electrodes, and the prevention of blows or breaks in the surface all help to reduce dissemination; consequently, all of these improvements should be made, if possible, to cut down the effluent load. In addition, in order to minimize the volume of contaminated air that has to be cleaned, the furnace should be enclosed as much as possible. Test Arrangements Before fundamental studies with collectors were made, a furnace stack selected for the test program was sampled to determine the gas temperatures and

Jan 1, 1956

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

OUT of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the seasor1 of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in low gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1938

CHARGING of an open-hearth heat is begun as soon as possible after the previous heat has been tapped. Ordinarily, about 40 min is required to drain and dress the furnace hearth, make up the taphole, and perform routine repairs of the banks. Repairs to the upper back wall and to the front wall and jambs can ordinarily be done while the first scrap charge is being heated and are therefore allowed to wait in order to save furnace time. Any major repairs required on the hearth or other parts of the furnace necessitate longer delays because such repairs must be made while the furnace is empty. Although charging practice varies considerably in detail with the type and proportions of scrap and iron used, many factors are common to all varieties of charge. Such general considerations are dealt with first. CHARGING EQUIPMENT AND STOCK HANDLING The physical equipment available for loading and weighing the stock, transporting it to the furnace, and charging it, may have a major effect on charging practice. Limestone, scrap, and all other solid melting stock are charged mechanically by means of equipment illustrated in Fig 2-1. The charging of hot metal is shown in- the background of this figure. Mechanical equipment and plant layout for stock handling are described in Chapter 1. It is generally desirable to charge the scrap about as fast as the physical volume can be put into the furnace. Charging scrap that is too heavy or adding the charge too rapidly (less than 45 min) may be detrimental to melting rate because of excessive chilling of the entire furnace system and also because of poor conduction of heat to the lower layers in the furnace; but the more common problem is the reverse one of charging light scrap fast enough to maintain a normal heat time. A limiting factor may be the height to which the scrap may he piled in the fur-

Jan 1, 1964

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the classification of coals according to rank and quality of grade. The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to fixed carbon content, calculated to the dry, mineral-matter-free basis. Groups of lower rank are divided

Jan 1, 1950

By Robert C. Stephenson

LARGE deposits of titaniferous magnetite occur associated with anorthosite and gabbro in the Lake Sanford area, Essex County, New York. The ore, gabbro, and anorthosite show consanguineous relations. Anorthosite grades through gabbroic anorthosite into gabbro but is locally intruded by gabbro. Structural and petrographic evidence suggests that gabbro was differentiated from anorthosite by filter pressing. Field and laboratory study of ore occurrences indicates that an ore residuum concentrated in the gabbro through magmatic segregation by normal crystallization and flowage. Ore occurs as bands which grade into gabbro, and also as large masses which replace anorthosite. Ore in the gabbro is finer grained and richer in ilmenite than ore in anorthosite.

Jan 1, 1945

By Henry Mulryan

DIATOMS are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skeletons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of vary-ing thicknesses. DIATOMITES Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition.

Jan 1, 1939

By W. F. Flanagan, D. H. Polonis, S. D. Dahlgren

Rotation diffraction patterns of Cu-4.84 wt pct Si polymystalline samples were taken during the course of isothel-ma1 affing of the suPersaturated a phase, a diffraction spots were obserzled to streak during the initial stages of aging, and this streaking was similar to the streaking of a spots observed earlier by Barvett with deformed super saturated samples of the same composition. Although it was suggested that stacking faults were the sole cause of styeaking in the deformed samples, the present study has shown that plates with one small crystallite dimension can also contribute to the streaking when there is lattice coherency across close-packed planes. THE decomposition of the supersaturated a phase in Cu-Si alloys has been reported to occur by means of both thermal and stress activation.1-4 According to the Cu-Si phase diagram,3 Fig. 1, the supersaturated a phase (fcc) is expected to transform during aging by the precipitation of the y phase. The results of earlier studies2,4 have indicated that metastable k phase (hcp with nearly ideal close packing) forms initially at temperatures below the eutectoid temperature, after which the k transforms to the a and y phases. Hof-mann et al.4 have proposed a metastable version of the phase diagram, showing the approximate boundaries for k formation below the eutectoid temperature. In view of the close-packed nature of both the a and k phases, it is essential to consider the role assumed by stacking faults in the transformation. Streaking effects have been reported by Barrett 1 in the rotating crystal X-ray patterns of strained Cu-Si alloys and were attributed to stacking faults rather than particle size effects. This deduction was based on the observation that streaks in the diffraction patterns did not occur tangent to the 220fee Debye ring. It is known that the atom movements involved in faulting leave some X-ray reflections unaffected while others are broadened,' and, in particular, it has been shown that faulting will not cause streaking of 220fee reflections tangent to the 220fee Debye ring as would be expected if all the reflections were broadened.' The formation

Jan 1, 1967

Jan 1, 1958

Jan 6, 1976

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as on control of furnace practice. This chapter deals only with those raw materials of the basic open-hearth process which are important in determining the composition of the steel or slag. They are the metallic charge, oxygen-bearing materials, fluxes, and alloying and deoxidizing additions. Refractories, which may also affect the slag composition, are discussed in the previous chapter. Wide variations are possible in the type and composition of charged materials, but in all cases certain fundamental relationships among the elements of the charge must be maintained. Since the process consists essentially of refinement by oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters II and VII). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme would be the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not subject to oxidation or other reactions resulting in their elimination, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type would be found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should below in copper, or a sufficiently high ratio of pig iron to scrap should be charged to dilute the copper from the scrap, so that the average copper content of the melt will be below the required maximum.

Jan 1, 1944

By Lucien F. Trueb

The microstructure of explosion-bonded pairs of similar and dissimilar metals has been investigated by electron microscopy. A review of the specific problems encountered and the methods used for obtaining surface replicas and thin-film transmission specimens of the bond interface is given. The bond area is mainly characterized by continuous and practically diffusionless metallurgical bonding. The very large shear stresses induced along the collision front of the plates being joined causes extreme grain elongation and a symmetrical pattern of subgrains in the bonding direction. The bond zone is also characterized by a very high density of dislocations and pressure-induced twins. Localized heating occurring during the cladding process can result in partial re-crystallization or the formation of thin layers of molten material. The force of precisely controlled explosions causing a high-velocity impact between metal plates has been used for several years to achieve metallurgical bonding between an extremely wide variety of metals. This method essentially consists of accelerating a plate to high velocity toward a stationary plate by a detonating explosive. Since the restrictions to bonding are not those encountered with conventional nethods, it becomes possible to bond pairs of metals having widely different mechanical properties that are immiscible or form brittle intermetallic compounds. Many applications of such composite metals are found in the field of corrosion protection as well as numerous other fields; for example, explosion bonding is being applied for fabricating the materials used by the United States Mint in the new sandwich-type coins. The primary condition for establishing a metallurgical bond is that absolutely clean metal surfaces be brought together. Any metal exposed to the atmosphere is covered with oxides, adsorbed gases, and other contaminants; even a very forceful impact of two such surfaces is not sufficient for bonding. Cowan and Holtz-man,"' who reviewed the dynamics of colliding plates in detail, showed that in order to achieve a good bond the explosion conditions must be chosen in such a way that the plate collision velocity is less than the sonic velocity, in which case no oblique shock waves are attached to the collision front. A pressure wave is then generated ahead of the collision line, and the material forming the colliding surface of each of the plates flows forward and is ejected in the form of a spray, the so-called jet. The dynamic elastic limit of the metals must be exceeded so that there is sufficient plastic deformation. At the point where the jet formed by the junction of the inner surface layers of both plates separates from the combined plates, the material experi- ences a very high shearing strain and the pressure can reach several hundred kilobars. This process strongly influences the microstructure of the bond zone as will be seen later. Behind the collision front, uncontami-nated layers of internal material are brought together under high pressure and are thus metallurgically bonded. I) STRUCTURE OF EXPLOSION BONDS The different types of explosion bonds that can be obtained depend on the explosion conditions, and have been investigated by Cowan and Holtzman,1'2 Holtzman,3 Klein; Bahrani and crossland,' and Buck and Horn-bogen. The preferred kind for practical applications is the so-called wavy bond, typical examples of which are given in Fig. 1 showing light micrographs of various metal-to-metal interfaces. In forming this type-- of bond the collision energy is mainly expended in jetting, the formation of waves, and localized melting. Beyond the crest of the waves, eddy-shaped areas are observed in which the two metals are mixed in a complex pattern of streaks. Cowan and Holtzmanl first proposed that this wavy pattern is analogous to periodic eddy shedding in the flow of a viscous fluid around an obstacle (Von Karman's eddy street). The mass of metal ahead of the stagnation point, which is associated with the jet and has forward momentum, plays the role of an obstacle and the eddies created in the flow of solid metal around the stagnation point are preserved in the final clad specimen. This idea has been reviewed more recently by Klein4 and the variables involved in the wave formation have been discussed in some detail by Bahrani and crosslands and Buck and Hornbogen.6 Several studies of the structure of explosion bonds by light metallography have already been published.1-6 Aside from the waviness and the eddies which were mentioned above, the most striking characteristic of the area in the vicinity of the bond interface is a very considerable longitudinal grain deformation which appears to be strongest at the metal-to-metal boundary and dies out as one moves away from it. Large twins are often observed within the deformed grains, and molten areas are found in the center of the eddy-shaped structures situated beyond the crest of the waves. The large hydrostatic pressures and shear stresses occurring at the interface modify the mechanical and chemical properties of the bond zone. Increases in hardness in this area have been reported by various authors.396 The defects along the interface can also cause a local increase of the chemical reactivity and thus might be expected to boost the etching rate. However, the effects of this preferential etching cannot be observed by light microscopy due to its inherently limited resolution power. The same limitation precludes the observation of morphological features directly along the bond interface as well as the interface itself. Furthermore, no information can be gained by light-

Jan 1, 1969

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By B. H. Kear, B. J. Piearcey

The orientation and temperature dependence of the tensile and creep propevties oj Mav-M200 crystals halle been determined. Crystals oriented for single slip exhibit ,maximum ductility, minimum work hardening, and least creep resistance, whereas crystals in multiple slip orientations show nzinimu~n ductility, strongest work hardening, and greatest creep resistance. At 1400" and 1600°F there is a marked improzlenzent in creep strength for orientations approaching [001] and [111], indicating that interactions between dislocations gliding in intersecting octahedral slip systems play an important role in creep resistance. At 1800°F the creep strength is much less dependent on orientation, which is rationalized in terms of slip in cube planes as well as octahedral A frequent mode of failure in high-strength cast nickel-base superalloys is by intergranular fracture, particularly along those grain boundaries oriented transverse to the major stress axis. VerSnyder and ~uard' demonstrated that this problem could be overcome by eliminating transverse grain boundaries through unidirectional solidification. Piearcey and versnyder2 made use of this principle in the development of unidirectionally solidified gas turbine blades and vanes, where the growth direction of the columnar grain structure coincides with the axis of principal stress under operating conditions. The present investigation was undertaken to determine if further improvement in properties may be obtained by eliminating grain boundaries altogether, so as to take advantage of the well-known dependence of mechanical properties of single crystals upon the orientation. 1) EXPERIMENTAL PROCEDURE Single crystals of Mar-M200* were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold, and crystal growth was promoted from one end by appropriate gradient cooling. Tensile and creep specimens (2 in. diam by $ in. gage length) were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. The orientations of the specimens were determined by the Laue X-ray back-reflection method. Tensile tests were carried out in aWiedemann machine with furnace attachment, using a strain rate planes. In all orientations imzpvouement in the strength charactevistics of the material can be induced by heat treatment. Creep ad stress rupture data for (001) oriented crystals are compared with similar data obtailted previously joy random polycvystalline material, and also columnar grained material having a prejevved (001) orientation. The single-crystal )material exhibits both longer rupture life and lower minimum creep rate at all temperatuves, and the rupture elongation is comparable with that in the columnar grained material. From these results it is concluded that single crystals should and useful application in gas-turbine blades and tanes. The optimum orientation for a blade is considered to be with its axis of principal stvess parallel to (001) ou (111). of 0.0001 sec-'. Load and extension were recorded directly on an X-Y recorder. The strain measuring device consisted of extension arms attached to the grips at one end and leading out of the furnace to an LVDT (linear variable differential transformer) at the other. Creep tests were performed using a standard constant load creep frame. 2) DISCUSSION OF RESULTS 2.1) Structure of Alloy. The structure and segregation in as-cast and heat-treated Mar-M200 has been described in detail else where.~ The main features are as follows: the as-cast material is heavily cored, due to pronounced dendritic segregation during solidification; the dendrites are rich in tungsten and cobalt whereas the interdendritic regions are rich in chromium, titanium, nickel, and carbon. The structure consists of -60 vol pct coherent precipitate of y', basically Ni3(A1,Ti), in a matrix of y (nickel-base solid solution), interspersed in the interdendritic regions with minor MC carbides and -y' eutectic. The y' particles, and y-y' eutectic, contain more titanium, aluminum, and nickel, and less tungsten, cobalt, and chromium than the y matrix. Heat treatment partially removes segregation, eliminates the eutectic, refines the y' dispersion in y, and gives additional partially coherent M23Cs carbide. An as-cast crystal, therefore, is composed primarily of two oriented phases (y + y'), whereas the normally heat-treated crystal consists of three oriented phases (y + y' + MZ3Cs). Typical electron transmission micrographs of the y + y' structure are shown in Fig. 1. Crystals grown in the (100) orientation develop a simple unidirectional dendritic structure, Fig. 2, since (100) happens to be the preferred direction of growth for dendrites in this material. Crystals grown in the {110) and (111) orientations, however, tend to promote equal growth, generally in separate colonies, in the two and three geometrically favored (100) growth directions, respectively. In other orientations of growth, a single (100) dendrite direction generally pre-

Jan 1, 1968

By R. Kerby, T. R. lngraham

The rates of cadmiuln cementation from buffered solutions were studied on both the cylindrical and circular faces of a rotating zinc disk. The activation energies are equivalent on both surfaces, but the rate is more rapid on the cylindrical face. At higher temperatures and at pH values above 6.4, the rate of deposition increases because of an increase in the cathodic area of the deposit. The rate may also be increased by decreasing the thickness of the diffusion layer by rapid stirring. The presence of small amounts of copper, cadmium, lead, iron, or aluminum in the zinc does not affect the cementation rate, but when srnall amounts of copper, cobalt, and arsenic were present in the solution cadmium deposition ceased shortly after it started. Small amounts of copper in solution become cemented with the cadmium to form a coarse deposit of Cd3Cu. When zinc ores containing cadmium are processed for electrolysis, the cadmium appears with the zinc in the leach liquors. Because of the discharge potential of the cadmium ion and the hydrogen overvoltage on metallic cadmium, the cadmium ion must be removed prior to zinc electrolysis to prevent its codeposition. Cadmium is usually removed from acidic zinc sulfate solutions by cementation on zinc. When zinc sheets are used with the appropriate conditions of pH and temperature, a finely divided, high-purity cadmium powder is obtained; it floats to the surface with attached hydrogen bubbles and, after careful washing, may be processed directly to a marketable product.' The reaction on zinc sheets is relatively slow because of the limited amount of exposed cathodic area on the sheets. A much more rapid reaction is obtained when zinc powders are stirred into the solution, but this procedure does have a potential disadvantage: some unreacted zinc may be trapped in the cemented cadmium and thus lower its grade.1 The equilibrium constant at 25°C for the displacement of cadmium by zinc is of the order of lo", which indicates that at equilibrium the displacement would be essentially quantitative and no back reaction need be considered. This indication is not entirely true, however, because in the presence of oxygen any loose cadmium which is out of contact with metallic zinc tends to redissolve after cementation.' The overall effect is much the same as that to be expected if the equilibrium constant were much smaller. Previous experimental work on cementation reac- tions3 is in general agreement that the rates of cementation usually follow first-order kinetics. The metal on which cementation occurs is considered to consist of anodic areas from which metal dissolves and cathodic areas onto which the reactive metal is cemented. For the reaction to continue, the cemented deposit must remain open and porous for the removal of ions. Usually, the deposited metal influences the rate of cementation; when it blocks the pores in the deposit, the rate of cementation will be decreased. Alternatively, when the cemented metal grows as den-drites or as coarse powder the cathodic area is correspondingly increased and the rate of cementation increases,3 Thus, it is only during the initial stages of cementation, prior to the development of deposit effects, that the kinetic behavior of the reaction may be studied without ambiguity. In this paper, experiments will be described for cementation of cadmium from dilute solutions onto the surface of a rapidly spinning zinc cylinder. The effects of ionic concentration, disk rotation speed, temperature, and impurities will be described. APPARATUS AND PROCEDURE The apparatus used for the experiments was described in a previous paper.4 It consisted of a 2-liter vessel in which the contents were protected, against oxidation, by a stream of prepurified nitrogen. The vessel was immersed in a water bath which controlled

Jan 1, 1970

By Roger V. Pierce

INTRODUCTION IN the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centered upon haulage, hoisting equipment, mill flowsheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materials. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain ore bodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered ore bodies are moving rapidly from stopes to reduction plants-because it is now possible to develop an ore body and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials of mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining. In some places it has been found economical to change from one system of stoping to another that more readily allows the application of mechanical muck-handling equipment. Where blocks are worked faster, the cost of materials, time, and labor is cut drastically. This favorable situation allows more manpower to remain on straight breaking and timbering-or straight production mining. More-over, when blocks are mined faster, more floors can often be mined vertically before the mucking or wheel floor is moved. This results in several direct savings. There are cases where it has been proved that by working a given block faster more area, longitudinally or vertically, could be mined at one time, thus permitting the reduction of development cost. (Fig. I.)

Jan 1, 1943