Search Documents

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

INTRODUCTION IN a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress.‡ The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into use with the same significance as "technical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens between yield and fracture. A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress S3 to the longitudinal stress Sl.* The results of the experiments are represented by a series of complete flow-stress curves for each of the metals investigated, and these diagrams have been used for the development of other diagrams of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not on the stress system, he was correct in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, would seem to be axiomatic, provided that the flow stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard of this principle has led to some untenable theories of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1948

By T. E. Wayland

The general geology and mineralogy of bentonite, including pertinent technological details of clay minerals in the montmorillonite group, are summarized. Worldwide occurrences of bentonite deposits are reviewed, with emphasis on geologic methods and economic principles of evaluation. Active mining districts are described and areas with potential for current and future development are assessed. The production history of bentonite, principal producers, major consumers, and indicated trends are noted; also attention is directed to the hundreds of minor industrial uses of this versatile material, ranging from the manufacture of (A)cid neutralizers to (Z)eolite water softeners. Recent significant results of both basic and applied research are reported, with suggested lines of investigation for current and near-future consideration.

Jan 1, 1972

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By F. E. Bash

Constantan is an alloy of copper and nickel that is extensively used, under a number of trade names, as a resistance wire with a low temperature coefficient of resistance, and one of the elements of base-metal thermocouples, iron usually being the other thermoelement, although for low-temperature work copper is also used. Before the war, constantan was imported, in common with many other technical necessities. Since it required considerable time to receive the constantan after it was ordered, fairly large stocks were kept on hand; but after the beginning of the war no more was imported and the stocks of foreign material were exhausted about the same time that the steel and munition manufacturers began to need great quantities of it for thermocouples for the heat treatment of steel. To meet this demand, the International Nickel Co. began manufacturing constantan that met all the requirements of the users of resistance wire but did not give the same electromotive force against iron as the German material and consequently could not be used with instruments calibrated for a definite e.m.f.-temperature relation. It so happened that all the constantan made had an e.m.f. lower than that necessary to meet the specifications of the Leeds & Northrup Co. for whom this investigation was carried out. If some had been higher and some lower, good wire could have been obtained by a process of selection, but as it was no wire at all could be procured. To remedy this situation, a thorough investigation was started with the close cooperation of the International Nickel Co. and the Electrical Alloys Co. The specifications to which the constantan had to conform were that it should give an e.m.f. of 47.40 millivolts against pure iron at 1500" F. (816" C.) with the cold-junction temperature at 0" F., or a proportional e.m.f. at temperatures near 1500" F. The method of checking a wire was as follows: It was first welded to a piece of iron wire; Armco iron was found to be satisfactory but iron with greater than 0.1 per cent. carbon would give a lower e.m.f. against the same piece of constantan than pure iron. The couple was then insulated and the fire end was tied to the

Jan 1, 1921

By T. E. Leontis

The importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication, attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne. The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Znt alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-~Zn,f Mg-jZn, Mg-4.4211, Mg-6Zn, and Mg-roZn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. Literature The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison. Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,' Dumas and Rockaert, Haugh-ton and Prytherch,6 and by Spitaler, the last being reported by Beck.' A slight superiority in the tensile strength of chill-cent Mg + 8 es alloy Over the sand-cast alloy was noted by Maybrey.8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1949

By Thomas G. Murdock

EthIopia, the first country to be liberated from Axis domination, has recovered remarkably from the ravages of occupation and war. Mineral production has contributed significantly towards this recovery, as it has provided a means of obtaining foreign exchange and has given employment to hundreds of workmen whose maintenance otherwise would have presented a problem. Although primarily an agricultural country, never with a large mineral production, Ethiopia has within its borders a variety of minerals, both precious metals and nonmetallics. Some of these are important to the country as a national asset and others contribute greatly to local economy and can be expected to do so even to a greater extent in the future1 (Fig I). Physiography and Geology The Empire of Ethiopia is essentially a mountainous and volcanic country, in northeast Africa, situated principally between latitude 4° and 15°N and longitude 34° and 44°E. It is bounded on the north by Eritrea, on the northeast by French Somaliland, on the southeast by Italian Somaliland, on the south by Kenya Colony, and on the west by Anglo-Egyptian Sudan. These European possessions thus completely surround the country. Its access to the Red Sea is through Eritrea; to the Gulf of Aden, through French or British Somali- land ; and, to the Indian Ocean, via Italian Somaliland. These routes range in length from 40 to 250 miles. Ethiopia has an area of approximately 350,000 square miles, with a width from north to south of 625 miles, and a maximum length from east to west, along latitude 8°N, of about 875 miles. Physiographically the country is characterized by two very extensive sub-tabular plateaus: the Ethiopian Plateau to the northwest and the Somaliland Plateau to the southeast, separated by a long tectonic graben—the Rift Valley of the Galla Lakes and Danakil. The Ethiopian Plateau, deeply cut and notched by the drainage, slopes in a general northwest direction toward the Sudanese Plains and the valley of the Nile; the Somaliland Plateau slopes to the southeast, toward the Indian Ocean. The valley of the Galla Lakes and its extension to the northeast—the Awash River Valley, separates the plateaus, from Lake Rudolph to Danakil. This depression which constitutes a continuation or ramification of the Great Rift Valley of Central Africa joins in turn the trough of the Gulf of Aden and the Danakil-Eritrean Rift, continuations of the Red Sea and the Jordan Valley. The general basement of Ethiopia is made up of very old rocks, usually considered as Archaen.2 These rocks are represented by the metamorphic crystallines, such as gneisses, different kinds of schists, included lenses of crystalline limestone, and massive intrusives such as granites, diorites, and syenites, all cut by

Jan 1, 1949

By P. F. Gnirk, J. B. Cheatham

The results of combined analytical and experimental studies involving simulated multiple bit-tooth penetration into mck are incorporated into a drilling rate equation for roller-cone bits assuming rather idealized downhole conditions. In particular, it is assumed that the rock behaves statically in a ductile fashion during bit-tooth penetration and that the rock chips are instantaneously removed from the bottom of the drill hole. The general analysis demonstrates an application of plasticity theory for the rock/bit-tooth interaction to the formulation of an upper limit on rotary drilling rate. INTRODUCTION Extensive experimentation involving single and indexed bit-tooth penetration into rock in a confining pressure environment has demonstrated that the chip formation process is of a ductile, or pseudoplastic, nature at sufficiently low differential pressures so as to be of interest in rotary drilling. Coincident with the experimentation, analytical consideration has been given to the theoretical problems of single and indexed bit-tooth penetration into rock. In general, the analyses have assumed that the rock behaves statically in a rigid-plastic fashion and obeys the Mohr-Coulomb yield criterion. The quantitative comparison between experimental and calculated values of bit-tooth load required for chip formation has been remarkably good for a variety of rocks commonly encountered in drilling and at simulated differential pressures as low as 500 to 1,000 psi. Results obtained recently for indexed bit-tooth penetration indicate that the work (or energy) required to produce a unit volume of rock chip can be minimized by a proper combination of bit-tooth spacing and bit-tooth load for a given rock type and differential pressure. By utilizing this information, it is possible to formulate a drilling rate equation, at least in a preliminary fashion, for a roller-cone bit performing under rather idealized downhole conditions. In particular, through the use of characteristic dimensionless quantities pertinent to a roller-cone bit and to indexed bit-tooth penetration, interrelationships among bit weight, rotary speed, rotary power, bit diameter, rock strength and bit-tooth shape and spacing can be explicitly expressed. In the formulation of the equations, however, it is assumed that the rock chips are instantaneously removed from the bottom of the drill hole and- that the rock behaves in a ductile manner during bit-tooth penetration. In addition, the effects of bit-tooth load application and penetration by a yawed tooth at an oblique angle are neglected. Although the analysis is presented in the light of some rather restrictive conditions, it does demonstrate a method of applying fundamental rock/bit-tooth interaction data, obtained by combining the results of analysis and experiment to the formulation of a drilling rate equation for rotary drilling. JNDEXED BIT-TOOTH/ROCK INTERACTION PREVIOUS RESULTS The mechanics of bit-tooth/rock interaction under simulated conditions of borehole environment have been extensively described in a number of papers.l-ll In particular, the effects of differential pressure, mechanical properties of rock, pore fluid, bit-tooth shape and spacing, rate of bit-tooth load application and dynamic filtration below the bit-tooth have been investigated experimentally. From a sequence of experiments.1-4 it was demonstrated that, for dry rock at atmospheric pore pressure, the mode of chip formation exhibits a transition, with increasing confining pressure, from predominantly brittle to predominantly ductile. This transition

Jan 1, 1970

By Philip B. Bucky

[ ]

Jan 1, 1942

By J. D. Grace

Screening by centrifugal force is a unique subject, for all vibrating screens, with but one exception, depend on gravity alone to pass material through a sizing mesh or screen cloth. Centrifugal screening is one of the greatest advancements made in screening since the development of vibrating screens. It makes possible sizing in a range previously im-practical by mechanical methods. The centrifugal screen is specially designed for fine sizing from No. 4 separations to finer than No. 100 separations. Centrifugal force provides a positive control of factors that make fine particle separation practical and effective as opposed to gravity which is a fixed force acting only in a fixed direction, The centrifugal screen provides a control of the force of material against the screening surface, and also controls the distance of departure of the material from the surface and its rate of return. The centrifugal screen has a rotating drum that becomes a natural fan blowing air outward through the material being screened and carrying float dust and fines through the apertures with it. Screening by centrifugal force is an unique subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey material along the screen, is the Symons V-Screen. The requirements of the industrial minerals industry to meet ever-increasing stringent fine sizing specifications by a practical mechanical method accentuates the weakness of gravity, a fixed force acting in a fixed direction, as a prime force for fine sizing. It was apparent a force other than gravity was needed. This led to the development of a centrifugal screen to meet modern demands for practical fine sizing operations. Gyratory-type screens in use today were originally designed in a day when a 1/4-in. separation was normally considered fine sizing and 1/8-in. separations were extremely fine sizing. Although gyratory-type screens are sometimes used for separating below 1/8-in., they are not practical screens for this purpose. They were not designed to do this type of work. A growing demand for a practical means of making positive mechanical separations in a range of from 1/8 in. downward led to the development of the vibrating screen. These screens utilize higher speeds and lower amplitudes of vibration than

Jan 1, 1967

By F. S. Norcross

DEVELOPMENT of the manganese deposits of Cuba is a matter of importance not only to those involved in this industry on the Island but to the United States steel industry and to our Nation as a whole. For years our domestic resources of manganese have been wholly inadequate, but the recent Cuban development points the way toward solution of this strategic mineral problem.

Jan 1, 1939

By R. E. Reed, C. J. McHargue

Single crystals of aluminurn were reduced 90 pct in diameter by extrusion at 296" and 77°K. The resultant double fiber texture had a strong (111) component with a weak (001) component. The relative anzounts of these components varied with starting orientation. Decreasing the Lemperatuve of defovtnation increased the amount of (001) texture component in crystals with inilia1 orientations near (111). The starting orientation and temperature of deformation strongly affected the morphology of the (001) component. The effects of orientation and Lemperatuve upon the distribution of the (001 ) texture component in extruded aluminum single crystals were rationalized on the basis of deformation band formation and interaction. MANY papers since the early 1920s have discussed the occurrence of the double fiber texture (111) + (001) in wires and rods of deformed fcc metals. Aside from the reporting of experimental results for the various metals under a variety of fabrication conditions, emphasis has been placed on two related problems. One problem deals with the prediction of ideal end orientations based on the glide systems and flow directions. The other problem seeks the reason why different amounts of each component may be produced by the same fabrication schedule for metals apparently having the same deformation systems. Some of the difficulties in developing a satisfactory explanation have their origin in the experiments themselves. One mistake has often been the assumption of an initially randomly oriented specimen or complete ignorance of effects of starting orientation. Recent studies by Grewen and Wassermann,1 Cullity and co-workers,2' and McHargue4 have shown that the initial orientation may be the most important factor in determining the final orientation. Hence only limited comparisons of data from different studies can be made unless all conditions of the initial material are specified. Another question has been the nature of the (001) component. Hibbards suggested that any (001) present was the result of re crystallization during fabrication. Although Fleischer6 found no (001) texture in aluminum swaged at room temperature, and Dayal 7 found that component to disappear at very high reductions, a double fiber texture has usually been reported for aluminum. Vandermeer and McHargue showed that, while some (001) in aluminum may be the result of recrystallization, much of this component has its origin in the deformation process. Ahlborn and Wassermanng found the (001) component in silver deformed at low temperature not to be the product of recrystallization.

Jan 1, 1968

By James F. Magee

There is nothing new about dragline dredging for placer gold. The use of the separate unit for excavating preceded the large barge with excavator mounted upon it, which has reached a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant combining a dragline excavator on caterpillar mounting and a gravel-washing plant on a floating barge. The most efficient ones use a bucket of 1 to 2 yd. capacity with boom from 40 to 70 ft. long. The barge varies from 20 by 30 ft. to 36 by 48, and carries the trommel screen, pump, riffle sluices and power engine. Plants in Oboville District In the Oroville district eight such plants have been built since 1933, and have been operated with varying success. The most successful of these is the plant of the Wyandotte Gold Dredging Co. This organization of six active partners constructed its first plant on Wyandotte Creek in the autumn of 1933. To September of 1935 about one million cubic yards of gravel was dredged for an output of about $225,000 in gold. The operation has been successful from the beginning, because of wise management, which was based upon good plant design and proper principles of operation. All the partners have taken a more or less active part in the operation. Usually there is one at work on each shift, and they have conducted their own prospecting and building also. They elected H. F. England as manager, with wide power of control, and he carries out this responsibility energetically and successfully. One of the other plants, started shortly before the Wyandotte, finally abandoned its operation and sold its ground to the latter company, which successfully worked it for a profit. The failure of the other plant was due principally to poor excavating equipment. Another organization that built a plant some months later than the Wyandotte company had considerable difficulty in management and was unable to keep ahead of expenses. Finally, late last summer, it entered into an agreement with the Wyandotte company to have the latter supply

Jan 1, 1937

By S. C. Sun, A. M. Gaudin

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By A. M. Gaudin, S. C. Sun

This paper presents the results of a. study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresisl-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation _ 4µ(300)² Z= kx in which z is the zeta potential expressed in in volts, µ the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas. The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mixture of water, copper sulphate and xan-thate, we can calculate the zeta coefficient

Jan 1, 1947

By M. L. Fuller

DURING the last several years many papers have appeared dealing with the structure of highly polished metal surfaces. The awakening of interest in this subject is due to the applicability of the electron diffrac-tion technique to the study of surfaces. The original theory of Beilby1 considered the surface of polished metals as of the nature of a super-cooled liquid or a vitreous, amorphous solid. The electron diffraction effects from polished metals have been interpreted by many to be a direct experimental proof of the correctness of the Beilby theory. This inter-pretation has been strongly opposed by others, so that at the present time the subject is in an uncertain and controversial state. In the present paper new, and hitherto unpublished, electron diffrac-tion effects from polished zinc are described. These observations indicate that the polished surface of zinc is crystalline.

Jan 1, 1938

By W. M. Weigel

SALT production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open 'kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been estimated only by geophysical methods. The diameter of the salt core varies from less than ½ mile to over 2 miles. Only domes where the salt is compara-tively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use.

Jan 1, 1935

By C. S. Yust, Lida K. Barrett

The change in shape of the void in a sirzterir~g copper mass has been investigated as a juntction of' density. A serial sectioning' technique was used to eoaltrate the irregular shape of the void at two levels qf density. A measure of the void size and configuration, the proximity number, is defined and used to describe the progress of void removal. The process of. void removal deduced front the observations of this study contrasts with current sintering models in that it takes into account the irregularity of structure of a sintering mass and demonstrates that isolated Porosity does not occur first as spherical pores, but as large, definitely nonspherical sections of the void void volume. The process of sintering, about which there is much practical and theoretical knowledge, has evaded a direct and thorough analysis despite the intensity with which it has been studied for 60 years or so. This is due, of course, to the complex structure of a sintering mass and the inability to observe directly the development of a fully dense solid from the initial particulate arrangement. Extensive theoretical analyses have been based on the adoption of one or another of several model systems, that is, by visualization and analysis of some sort of regular assembly or arrangement of geometric "particles" approximating the conditions of a sintering mass. It seems appropriate at this time to try to examine experimentally in some detail the extent to which a sintering mass of irregular particles dlffers from these models. Many models deal with neck growth and the initial stage of sintering and follow the direction established by ~ucz~nski' in 1949 for the sintering of spheres to flat plates. Recently Johnson and cutler2 have adapted these models to sintering of powder masses. coble3 has presented a mathematical model for sintering that applies to the middle and final stages of the process. These papers, without exception, assume a regular geometry, generally spheres in contact in a regular array. Rhines~ and coworkers, however, are studying the sintering process by applying a model based on the topological concept of genus which permits them to consider an irregular structure. whites has described the various models with the exception of that of Rhines et al., and the assumptions on which they are based and their shortcomings. The present paper examines the geometric changes that occur in the powder mass during sintering by examination of the void. The method is to analyze a series of partially sintered structures and to propose from this analysis the sequence of events which occur in the removal of the void space as a sintering mass progresses from a collection of individual particles to a solid body. The irregular nature of the stacking of particles and of the particles themselves will be taken into account. The significant points derived from this study are: first, accurate reconstructions of the irregular void shapes are presented; second, it is clearly established that closed porosity occurs first as widespread volumes of interconnected porosity, definitely nonspherical in shape; and third, a new factor, the proximity number, is defined, which serves in this paper as a tool for describing the void shape changes observed, and which will be used in a later paper as part of the basis of a mathematical model for sintering. While the specific material studied is copper, the observations are thought to be relatively general as indicated by comparison of the results with partially sintered structures in other materials presented in the literature, both metallic and nonmetallic. EXPERIMENTAL PROCEDURE Four series of specimens representing progressive stages of the sintering process were prepared by sintering high-purity copper powder for various time periods. A relatively large particle size was used so that the void-solid interface could be readily distinguished at low magnification. In three series of specimens a loose stacking of particles was obtained by pouring powder into an alumina mold and lightly tapping the mold. The green density of such compacts was approximately 40 pct of theoretical density. Two of these three series utilized irregularly shaped particles in the size range -230 +325 mesh, one series sintered in vacuum and one in hydrogen at 950°C. The third series of loosely stacked particles consisted of spherical particles in the size range -270 +325 mesh, sintered in hydrogen at 950°C. A fourth series was prepared from compacted irregular particles sintered in hydrogen at 950°C. The specimens for this series were formed by lightly pressing the irregularly shaped particles in a steel die; the green density of the pressed pellets was approximately 60 pct. The irregularly shaped particles used in this study are shown in Fig. 1. The density of these particles, measured by a toluene picnometer technique, is 98.2 pct of theoretical density. Each particle is highly convoluted, and in some instances appears in cross section to contain internal porosity. The density measurement, however, indicates that completely enclosed porosity is very small so that the individual particles have a highly irregular surface but are essentially fully dense copper. Therefore, most of the void space that appears in two dimensions to be isolated within the particle is actually at the particle surface and connected to the external void in the dimension not included in the plane of the cross section. The void space that appears as void surrounded by the par -ticle or within folds in the particle w~ll be r~fc\r?

Jan 1, 1968

By R. D. Coleman, A. E. McIlhinney, C. E. Capes

tentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product.1 Fine Coal Treatment Processes Most coal cleaning methods depend upon the density difference between coal and its impurities to effect separation. These gravity concentration methods, however, are not practical for particles finer than about 100 mesh and cleaning methods dependent upon the differences in

Jan 1, 1971

By R. H. Kolb

A long term project at Shell Development Co.'s Exploration and Production Research Laboratory has been the improvement of the accuracy and the ease of BHP measurements. As a result of these efforts, two complete and separate systems have now been built for the automatic logging of BHP variations. The first of these is a small-diameter instrument suitable for running through production tubing on a single-conductor well cable. During the development of this instrument, as much emphasis was placed on providing a high degree of usable sensitivity and repeatable accuracy as on obtaining the advantages of surface recording. The second system combines the benefits of automatic, unattended recording with the convenience of a permanently installed Maihak BHP transmitter.' THE CABLE INSTRUMENT For many years the standard instrument for BHP determination has been the wireline-operated Amerada recording pressure gauge or one of several other similar devices. This gauge records on a small clock-driven chart carried within the instrument, and although relatively precise readings from the chart are possible, they are difficult to ob-tain. a Both the maximum recording time and the resolution of the time measurements are limited by chart size, and when a slow clock is required for long tests, the precision of the time measurement is often inadequate. Since it is impossible to determine the data being recorded until the gauge has been returned to the surface, wasted time often results when a test is protracted beyond the necessary time or when it is terminated too soon and must be re-run. Clock stoppage or other malfunctions which would be immediately apparent with surface recording remains undetected with down-hole recording; the test is continued for its full term with a consequent loss in production time. As new uses for subsurface pressure data evolved, the shortcomings of the wireline instrument became increasingly apparent, and the concurrent development of a surface-recording pressure gauge and the associated high-pressure well cable service unit' was undertaken. Description of the Instrument Because of its ready availability and advanced degree of development, the Amerada bourdon-tube element was chosen as the basic pressure-sensing device. This element converts a given pressure into a proportional angular displacement of its output shaft, and a suitable telemetering system was designed to measure accurately the extent of this displacement and to transmit the measurement to the surface and record it. The telemetering system furnishes a digital record printed on paper tape by an adding machine-type printer. The present arrangement provides a resolution of one part in 42,000 over the angular equivalent of full-scale deflection, giving a usable sensitivity of better than 0.0025 per cent of full scale. An additional refinement simultaneously records on the tape the time or the depth of the measurement, also in digital form. When the instrument is placed in operation, an adjustable programer can be set to initiate a read-out cycle automatically at selected time intervals. When subsurface pressures are changing rapidly, readings may be recorded as frequently as once every 10 seconds; when pressures are more nearly stabilized, the period between readings may be extended to as much as 30 minutes. Because the instrument is surface-powered as well as surface-recording, the maximum period of continuous logging is (for all prac. tical purposes) unlimited. The subsurface instrument is a tubular tool, 1 1/4-in. in diameter and 6.5 ft in length, operating on 12,000 ft of conventional 3/16-in. IHO logging cable. The transmitting section, mounted above the bourdon-tube element in place of the regular recording mechanism, contains no fragile vacuum tubes or temperature-sensitive transistors. This unit has been laboratory-tested to 1 0,000 psi and 300°F and has performed dependably during a number of field operations. The down-hole transmitting arrangement can be fitted to any standard Amerada pressure element, regardless of range and with no modification of the element itself. Calibration To obtain a repeatability commensurate with the sensitivity and resolution of the instrument, it was necessary to develop a special calibrating technique. The manufacturers of the Amerada recording pressure gauge claim an accuracy of only 0.25 per cent of full scale, which is a realistic figure for normal calibrating and operating procedures. An exhaustive investigation was made of the errors inherent in the bourdon-tube element, itself, independent

By Kenneth B. Barnes, George H. Fancher

With the advent of water-flooding into active commercial usage in half a dozen areas in the Mid-Continent, the process passes the experimental stage and joins other methods and processes now in use which have been found suitable in one oil field or another in securing a more profitable production than has existed heretofore. The use of the air-gas lift, acidization, pressure maintenance and repressuring have presented their problems in economics and engineering during their introduction and extended application. When a new field is discovered or attention is turned to an old producing area in which these methods have not been considered, it is to be expected that these problems again arise. While some information is available as to the results obtained by water-flooding in a few localities in the Mid-Continent, the extrapolation of the sand data on which the results are based, for even generalized use in other areas and fields in the region, is hazardous. It is precarious to assume that the same physical condition will obtain in a sand over more than small, special areas. This paper is concerned with a brief presentation of such data as are available to the authors on existing operations, a survey of the region and extent to which application of the method seems most likely to be made, an estimation of the crude reserve existing for such operations, suggestions as to the importance of core analysis in guarding against uncontrolled floods and its usefulness in predicting ultimate recoveries, and comment on some of the economic phases involved. These subjects, as concerned with water-flooding in the East (notably Bradford, Pennsylvania), have been discussed in detail in the literature and are generally well known. Especially is this true of discussions of the mechanical equipment and various lease layouts and development patterns for water-flooding.

Jan 1, 1936