Search Documents

By A. M. Rahm

PROBABLY the majority of red brass sand castings are judged merely on the basis of outside appearance and the quality of machined surfaces. Many castings, however, must individually withstand a hydraulic or air-pressure test before being accepted as parts of more complicated machin-ery. Finally, there remains a comparatively small group of castings intended for uses of considerable responsibility where only the highest possible characteristics of the metal are acceptable, and for these specially cast test bars are required. The shape of the cast piece from which the test bar must be detached varies greatly from one country to another. The test bar as specified in the American Society for Testing Materials Specification B62-36 is widely used by the American foundry industry. The actual test piece is at the bottom of the cast block and has a riser about six times its mass. It is obvious that this test bar has an advantage over the actual casting. The latter rarely possesses a riser of as much as 30 per cent of its own weight and that riser cannot generally be located in so convenient a manner. Therefore, the characteristics of the test bar cannot possibly correspond to those of the casting itself. It must be taken into consideration that red brass if melted and cast in the best possible manner may show a tensile strength of 40,000 lb. per sq. in. with 35 per cent elongation in 2 in. Such a test bar would indicate that the metal was nearly perfect from the viewpoint of its gas and inclusion content. Barring some accidental defect, a casting cor-responding to such a test bar could be accepted as being quite sound. However, actual specifications do not demand such high characteristics; indeed, few specifications require over 30,000 lb. per sq. in. and 20 per cent elongation, while one Federal specification demands merely 27,000 lb. per sq. in. strength and 15 per cent elongation. It is obvious that

Jan 1, 1939

By C Macquarie, Maurice Cook

Normally the grain size of cold-rolled and annealed copper sheet is of the order of 0.02 to 0.06 mm., and 0.1 mm., for example, would, for many purposes, be regarded as undesirably large. The occurrence of very large grain sizes in a few isolated cases of copper sheet led the authors to inquire into the causes giving rise to such unusual results. During the course of this work a very large number of experiments have been carried out to determine the effect of varying the conditions of the final and penultimate rolling and annealing operations, as well as of earlier rolling and annealing treatments. A correspondingly large number of observations have been made, but within the space of one paper it is possible only to outline relatively briefly what appear to be the more important of these experiments and observations. The presentation of the results does not follow chronologically the order in which the experiments were carried out and they have been rearranged for the sake of simplicity. In recent years a considerable amount of work has been done in connection with the recrystallization and grain growth in metals arid alloy. that take place on annealing, and a number of generalizations have beell reached. It is known that the crystal size in wrought material in the annealed condition depends on a number of factors, including the time and temperature of the annealing operations and the nature and amount of cold-work to which the material has been subjected. Results. however that are not covered by these generalizations can be obtained, which, in some instances, may even appear to be contradictory to them. Xccortling to these generalizations gradual changes in grain size are effected by progressive variation of the factors involved in annealing or cold-working. The work recorded in the present paper, however, relates to the development of grain sizes which are far beyond those normally encountered in ordinary annealing operations and far in excess of grain sizes which,

Jan 1, 1939

By C Macquarie, Maurice Cook

Normally the grain size of cold-rolled and annealed copper sheet is of the order of 0.02 to 0.06 mm., and 0.1 mm., for example, would, for many purposes, be regarded as undesirably large. The occurrence of very large grain sizes in a few isolated cases of copper sheet led the authors to inquire into the causes giving rise to such unusual results. During the course of this work a very large number of experiments have been carried out to determine the effect of varying the conditions of the final and penultimate rolling and annealing operations, as well as of earlier rolling and annealing treatments. A correspondingly large number of observations have been made, but within the space of one paper it is possible only to outline relatively briefly what appear to be the more important of these experiments and observations. The presentation of the results does not follow chronologically the order in which the experiments were carried out and they have been rearranged for the sake of simplicity. In recent years a considerable amount of work has been done in connection with the recrystallization and grain growth in metals arid alloy. that take place on annealing, and a number of generalizations have beell reached. It is known that the crystal size in wrought material in the annealed condition depends on a number of factors, including the time and temperature of the annealing operations and the nature and amount of cold-work to which the material has been subjected. Results. however that are not covered by these generalizations can be obtained, which, in some instances, may even appear to be contradictory to them. Xccortling to these generalizations gradual changes in grain size are effected by progressive variation of the factors involved in annealing or cold-working. The work recorded in the present paper, however, relates to the development of grain sizes which are far beyond those normally encountered in ordinary annealing operations and far in excess of grain sizes which,

Jan 1, 1939

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

This discussion was prepared by members of the Phelps Dodge Corpn. staff who were designated to review the minutes. It is confidential but permission has been granted to distribute copies among those who attended the Conference. The minutes of the above conference contain numerous references to the plants and practices of Phelps Dodge Corporation. As many of these references are inaccurate, the following notes are made covering such points: Construction Magnesite Brick in Reverb. Arch (1) An.18" arch, 20 feet long, was built on one furnace with 5 feet on each side of magnesite brick, the center portion .being of silica brick. The furnace was put in operation February 13, 1930 and on April 23rd after 68.8 days' operation it was replaced due to failure of the silica brick forming the center of the arch. At this time, while the silica brick had completely gone, there was 14" of magnesite left. Bridgewall Tapping (2) Tapping matte through the burner wall was first tried at the Copper Queen Smelter in April, 1925. At that time, a copper casting with 1 ½ extra heavy pipes for water cooling cast in it, and having one taphole block was used. Later, on the other (old) furnaces, similar castings, but equipped with two tapholes, were used. We found with these furnaces that we could tap through the burner wall at the beginning of a campaign, but would subsequently have to go back to side wall tapping. This was the case until sometime in 1926. The new furnaces, that went in operation at the beginning of 1927, each had water. cooled castings with two tapholes. These have been used entirely and have been quite successful. Sometime after the furnaces were put into operation sidewall tapholes were put in, simply for the removal of any accumulation of matte that might be temporarily retained at the front end by bridges or dams in the furnace formed by overcharging locally.

Jan 1, 1930

Jan 5, 1950

By John Norton

THE tremendous increase in the use of metals that have been prepared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations, It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing.

Jan 1, 1932

By Hugh R. Van Wagenen, Allen H. Rogers

There are few natural monopolies comparable with the nitrate industry. Perhaps the only other one is, curiously enough, also an essentia1 fertilizer material, viz., potash, of which the Germans have heretofore held practically a monopoly due to the existence in their territory of the most important known deposits of potash salts. And although nitrates in minute amounts are found in many desert regions, the only deposits capable of being worked commercially exist in Chile. Combined nitrogen in the oxidized form is an essential for plant life. Nature provides it mainly through the agency of nitrogen-fixing bacteria. But where lands are cropped artificially this supply is too small, and gradually the nitrogen supply becomes exhausted. In order to continue farming, it is necessary to furnish a supply of nitrogenous plant food, and this is done by putting on various substances containing combined nitrogen. These consist of various animal wastes, ammonium sulphate, the ammonia of which is obtained in the destructive distillation of coal, and Chile saltpeter. The latter is immediately available as a plant food, the nitrogen being in the required form. The other substances must oxidize before they are available. Resides its use as a fertilizer, Chile saltpeter is the source from which the bulk of the nitric acid of commerce is derived. The use of nitric acid in the manufacture of almost all modern explosives is, of course, well known. Importance of the Nitrate Industry Chilean nitrate, the existence of which was first mentioned in 1809, is said to have been first exported in 1830. Only a few thousand tons per annum were exported for some years, but the amount gradually increased until, in 1879, when the Chile-Peruvian war began, the export amounted to about 300,000 tons. This nitrate was largely produced from the Province of Tarapaca, until then, Peruvian territory. By the terms of peace with Peru in 1884, this province, as well as Tacna, became Chilean. The Bolivian Province of Antofagasta was also acquired as a result of this war, and thus Chile, with the deposits in her own territory, acquired control of the whole supply of nitrate. At the present time, exports are approximately 3,000,000 metric tons per annum,. having a

Jan 1, 1918

By C. A. Edwards

Jan 1, 1935

By C. A. Edwards

Jan 1, 1935

By Simon H. Ash

The coal-mining districts of Washington are mainly west of the Cascade Mountains; Fig. 1. The mines are on the foot hills of the slope, the lignite fields of Lewis and Thurston counties extending into the valleys west of the mountains. An exception is the Roslyn field, a small but important area on the eastern slope. If western Washington is divided into three areas from north to south, the bituminous coal fields and most of the active operations will be found largely in the middle area. The southern portion contains lignites over a large area. In the northern portion, mining is practically restricted to one mine, the Bellingham, which is working a subbituminous coal seam near the city of Bellingham. The degree of alteration that the coal of a particular field has undergone may be gaged roughly by the position of the field with reference to the Cascade Mountains. The lignites of Tenino, Tono, Mendota, and Castle Rock, on the railway line connecting Seattle and Portland, occur in a region of low relief, in which the Eocene coal measures have suffered only minor disturbances. Subbituminous coals occur in the foot hills, as at Renton, Newcastle, and Bellingham. Coalg high in fixed carbon are found nearer the mountains, where the measures have been sharply tilted and folded, as at Black Diamond and Carbonado. The two typical anthracite fields are located still higher, in the rugged mountains where outcrops appear both in deep gorges and on ridges at elevations approaching 5000 ft. At Carbonado is found the only semianthracitc seam worked on a commercial basis. The occurrence of this seam in a region of bituminous coal is due to the nearness of an igneous sill, which has changed its character from bituminous to semianthracite. Purpose of Paper On account of the various faults and dips and the varying nature of the wall rock, many difficulties are encountered in mining and winning the coal. The paper gives some of the methods used in mining and, in some detail, the conditions that affect the efficiency of these methods.

Jan 1, 1925

By Oliver Bowles

DIMENSION stone is a convenient term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, as contrasted with crushed, broken and pulverized stone, discussed in another chapter. Dimension stone includes cut stone, rough building stone, ashlar, rubble, paving blocks, curbing and flagging. Riprap-large, irregular blocks used for shore protection-is classed more properly with crushed and broken stone. COMPOSITION, VARIETIES AND PROPERTIES Stones used as blocks or slabs are of many kinds. The principal varieties are granite, sandstone, limestone and marble. Slate is covered in another chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. Limestone consists essentially of calcium carbonate, with which may be associated certain impurities such as clay, sand, or iron oxide. Dolomites and magnesium limestones used as dimension stone are classed with the high- calcium limestones, as they are used in the same way. Marble is a crystalline form of limestone. Sandstone consists essentially of silica in the form of sand grains cemented together into a coherent mass. Although rock occurrences are numerous and widespread, the ex- acting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced cracks, lines of weakness, or joints can be so used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive color, and freedom from impurities that may cause stains or deterioration usually are required also. Hardness is a variable property. Granites are as hard as or harder than steel while limestones and marbles may be scratched easily with a knife. The hardness of a sandstone depends upon the degree of cementation of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except when stones are subjected to severe abrasion, as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains.

Jan 1, 1949

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 79 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612' F. (322' C.), they redoccd the 79 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statenlent just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totsally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced colisumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opirlions advanced by different authorities in the scientific world to account for the apparent anomaly, bat none,

By P. H. Strickland, F. Lawson

It is now well established that in the majority of cementation processes used industrially, the rate of reaction can be described in terms of the mass transport from the bulk of the solution to the deposition sites on the metallic surface. Thus it should be possible to design cementation equipment from a knowledge of the flow situation in the equipment, and of absolute kinetic data. One way of obtaining such absolute data is by the use of the rotating disc geometry; this geometry is particularly suitable for a detailed study of cementation reactions. In spite of the similar mass transfer mechanism, cementation processes differ from other ionic transport processes in at least two respects. The presence of an attached deposit generally has a significant enhancing effect on the reaction rate; and side reactions involving oxygen and/or hydrogen ions can completely change the course of a reaction. Investigation of these peculiarities is necessary for a complete understanding of the process; since they cannot be isolated from the basic mass transport mechanism, close control of experimental conditions is essential. It has been found that the enhancement in deposition rate persists even when the deposit reaches a thickness several times that of the transport boundary layer thickness on the smooth surface. An explanation of the enhancement in reaction rate is proposed.

Jan 1, 1973

By Stanley D. Michaelson, Norman Weiss

This was a year of realization. Some years are for planning and development, some for designing and building, others for fulfillment. With greater hopes and plans for the future than ever before, the year 1954, nevertheless, will be remembered principally because of project completion. Among copper mines, for example, there were Silver Bell, Copper Cities, Bisbee, Yerington, and White Pine. In iron, there were the Humboldt, Coleraine, Cerro Bolivar, and Eagle Mountain. In asbestos, Johns-Manville's new mill at Asbestos, Que. In uranium, completion of the ninth mill on the Colorado Plateau-Kerr-McGee's at Shiprock, N. M. In research, 1954 marked the completion of Kennecott's Research Center in Salt Lake City, one of the historic forward strides in the science of minerals beneficiation. The year was fruitful in other directions as well. Investigations of a fundamental nature were on the upswing, and pilot plant projects have also increased in size and number. Progress in new reagents and equipment was greater than normal. It can already be conservatively predicted-from the technological point of view-that 1955 and 1956 will be tremendous years.

Jan 3, 1955

By Edward Walsh

In the early history of the production of metallic iron from the native oxides or ores, success attended the labors of the workman according to the care he devoted to his work, and according to the degree of skill he possessed in furnishing the required amounts of fuel and ores to be acted upon by the blast propelled by the bellows, trompe, or wooden tub, and delivered into the hearths of the Persian, bloomery, or Catalan forges. The same skill may also have been of avail in the use of the lower forms of the ".Stück," "Blue,"or" Wolf"

Jan 1, 1887

By K. D. McBean, W. H. Hannay, B. A. Stimmel

The electrolytic plant at Trail, B. C., was erected by the Consolidated Mining and Smelting Company of Canada, Ltd., for the treatment of zinc ores and concentrates, particularly those of the Sullivan mine at Kimberley, B. C. It began operations in 1916 at a rated capacity of 60 tons of cathodes per day, which has been steadily increased to the present production of 400 tons per day. The Sullivan has furnished the greater part of the zinc so far produced, although notable tonnages of customs zinc concentrates have been treated. The maximum yearly tonnage of customs concentrates, 25,000 tons, was treated in 1926. Practically no customs concentrates hale been treated since 1929. The total bar zinc production to the close of 1935 was 1,092,782 tons. The zinc mineral in the Sullivan ore is marmatite of somewhat variable composition, ranging between 6ZnS.FeS and 8 ZnS.FeS. Practically all the zinc ores tributary to this plant are marmatites; and the iron content of the zinc mineral varies considerably. The formation of zinc ferrite during roasting is now a matter of common knowledge, so the possible extraction from any zinc concentrate is largely a function of the iron content; the progress made in concentration is reflected directly in zinc-plant recovery. The Trail plant operafes on the low-acid system, as do all the other major plants on this continent at present operating, except the electrolytic plant of the Sullivan Mining Co. at Kellogg, Idaho. The new Magdeburg plant, in Germany, occupies an intermediate position between high and low acid. Plant operation at Trail will be treated in this paper under five main sections: roasting, leaching and purification, electrolysis, cadmium recovery and melting. The oxide section of the plant, treating zinc fume from re-treatment of lead blast-furnace slag, is practically a separate zinc plant; this is necessary because of the presence of fluorine in the smelter zinc fume. Cadmium is recovered electrolytically from the purification residues of both the sulphide and oxide leaching plants.

Jan 1, 1937

By C. R. Johnson, R. A. Greenkorn, E. G. Woods

A new method of reservoir evaluation called pulse-testins has been developed for describing formation properties between wells. Pulse-testing utilizes a sensitive differential-pressure gauge at a responding well to measure and record the response generated by a series of flow rate changes (pulses) at an adjacent or pulsing well. Since the pulse-test instruments have a sensitivity of about 0.001 psi, pulses of several hours or less in duration will generate a measurable response in most reservoirs. For this reason, many well pairs can be tested in a short period of time with little interference in field operations. Comparison of pulse-test results to conventional testing methods shows that the pulses obey unsteady-state, compressible-flow theory and thus provide a measure of both transmissibility (kh/µ) and storage (Fch). In additian, the method can be used qualitatively to describe communication across faults and between zones, and direction and tnagnitude of fracture trends. INTRODUCTION To obtain maximum usefulness of new reservoir analysis methods as well as to aid the field engineer in understanding local reservoir anomalies, improved methods are needed to describe heterogeneities in specific reservoirs. Optimum well spacing, equipment specifications, well completion design and especially the economics of pressure maintenance and secondary recovery programs depend on the extent and location of the heterogeneities that affect flow behavior in the field. One method for obtaining a measure of areal reservoir heterogeneity is an interference test. In the simplest interference test. constant-rate production or injection is initiated at one well and the effect of this flow is measured as pressure vs time at another well. Thus, during interference tests the flow characteristics of the formation are determined in situ. Despite their obvious usefulness in reservoir delineation. interference tests have not enjoyed frequent usage. Reasons for this have been the weeks or months required in many fields to obtain a pressure response measurable with conventional gauges, and the interruption of routine field operation during the field-wide shut-in normally required during these long times. Also, only average properties of the relatively large volume of the reservoir disturbed during these long times can normally be obtained — variations in properties between individual wells cannot be delineated. To eliminate these drawbacks of conventional tests, a special reservoir description technique called pulse testing' has been developed. Pulse-testing has several advantages that make it more convenient and practical for field use than interference tests. Valid tests are more certain because use of a series of flow disturbances gives rise to a diagnostic pressure response that can more readily be distinguished from unknown trends in reservoir pressure and other "noise." The time required is only a fraction of that for an interference test because a special, high-sensitivity differential pressure gauge can detect a much smaller pressure change. Variations in properties between individual wells can be delineated because of the relatively small volume of the reservoir disturbed during these short times. Finally, wells other than the pulsing and responding wells do not have to be shut in or carefully regulated.

Jan 1, 1967