Search Documents

By R. L. Wilcox, M. L. Fuller

Owing to the nature of the die-casting process, fresllly cast alloys are undoubtedly not at equilibrium from the standpoint of alloy phase relationships. After casting, therefore, they tend to undergo phase changes, with the ultimate effeet of reaching a state of equilibrium at the aging temperature, beyond which no fnrther change takes place. This phase alteration undoubtedly is one of the primary causes of the changes in dimensions and physical properties that zinc-alloy die castings undergo during aging. It is planned to report on this problem in a series of papers of which this is the first. The writers have made a study of commercial zinc die-casting alloys over a period of several years, utilizing the X-ray diffraction technic of determining the phase composition changes in the alloys. Up to the present, two principal phase changes have been observed which are capable of causing dimensional changes: (I) the segregation of secondary constituents from the zinc-base solid solution and (2) the beta aluminum-zinc decomposition. The latter is the subject of the present paper and studies on the former will be reported upon at a future time. Scope of Study In the present investigation a special technic for the study of the beta phase in zinc-alloy die castings has been developed, making possible the determination of the period of existence of the beta phase after casting. The pure beta constituent and its decomposition have been studied in detail. The effect of magnesium and copper on the velocity of the decomposition is reported. The heat of decomposition, the eutectoid temperature arid the accompanying density change have been measured. The density change lias been calculated from data on crystal structure and the result thus obtained has been compared with the actual change.

Jan 1, 1935

By Edward W. Parker

Note.—The material from which this paper has been prepared was collected tor the U. S. Geological Suvey Bulletin, No. 316, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. Although the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in moat cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which constitutes a considerable percentage of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections -of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Jan 1, 1908

By Albert Smith

THE creep properties of metals have as-sumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Insti-tute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influ-ence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investi-gate creep phenomena because of the sim-plicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals.

Jan 1, 1940

By R. E. Lund

Josephtown Smelter employs the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. The process uses resistance-type electric furnaces. Flow of current through the sintered ore and coke charge develops the energy required for smelting at the reaction sites. To produce zinc metal, the furnace off-Gases bubble through a large "U"-tube filled with molten zinc which condenses the zinc to liquid; the metal is then mechanically cast into slabs. To produce zinc oxide, the furnace vapors burn in air and the resultant powders are collected. The smelter comprises three distinct circuits. One circuit produces American Process zinc oxide and high grade metal; another circuit produces tailor-made alloys of controlled lead and cadmium content; the third circuit produces prime western zinc metal and feedstock which is refined into special High grade metal and French Process zinc oxide. The roasting circuit utilizes multiple-hearth furnaces for deleading the zinc concentrates; fluid bed and suspension roasters are employed for desulfurization. Sintering produces a hard, porous furnace feed. The flexible smelting process is adaptable to consuming various kinds of secondary material. Extensive residue treatment accomplishes high overall zinc recovery. Smelter by-products include sulfuric acid, cadmium, and mercury.

Jan 1, 1970

By Harrison Souder

In view of the proposed visit of the Institute to Cuba this winter, the following brief sketch of the principal mineral deposits near Santiago de Cuba has been prepared largely from notes taken in February, 1903, during a visit to the mines then in operation in the province of Santiago de Cuba. Westward from Cape Maysi, the most eastern point of the island, the coast is rocky and uninviting. The usual course of the steamers is well in toward the shore, and the lines of stratification of the rocks can be distinguished clearly, the presence of iron or other ores being indicated by frequent blotches of mineral stain. One is impressed with the general rugged character of the southeastern coast-line,—an almost unbroken barrier of coral-limestone bluff's, full of caves and hollows, into which the surf rushes with a roar and bursts into tall fountains of spray. Beyond rises abruptly the Sierra Maestra range, whose sharp, peaked crest-line betrays its eruptive or igneous origin. From a height of about 800 ft. near Cape Maysi, this range gradually rises to the westward, attaining its maximum elevation of more than 8,300 ft. in the Pico Turquino, beyond Santiago. A general resemblance to the mountain-ranges of southern New Mexico is noticeable. At Daiquiri, 20 miles east of Santiago harbor, the extensive

Jan 1, 1905

By J. H. Fletcher

ALTHOUGH some mines have been completely mechanized, on the whole mechanical equipment has made slow progress in the coal fields. Coal mining is particularly well adapted to hand labor. The skillful hand miner can keep his working place safe under difficult roof conditions, remove impurities from the coal at the point of origin, and produce a maximum percentage of large-size coal, so as to command the highest price on the market. Hand mining has also the advantage of low capital investment per ton of production and moderate carrying charge when the mine is idle. Though animal haulage gave way to electric locomo-tives and hand cutting to mining machines, beyond these concessions most of the tonnage is still produced by manual labor. But factors over which producers have no control are speeding the change to mechanical mining. The additional investment in underground equipment and surface preparation plant must be offset by a great increase in tons per man-day, and to do this the employees should be able to utilize as much of their time as possible on production. In the installation of mechanical mining, the only change in method usually has been to add loading machines to a mine already developed for hand loading. Because of a lack of suitable equipment, few mobile loading machines have been installed in seams of coal less than 4 ft. thick; the mechanization in the thinner seams has been confined largely to shaking conveyors and hand loading onto chain conveyors. Mechanical mining requires an organization that is prepared to study its particular problem from production territory to market in recognition of the changed factors arising from the use of loading machines at the working face, and other causes, such as safety of men and property; high wage scale on hourly basis; concentrated working territory and rapid extraction from a given area; change in the percentage of sizes of coal produced and effect of this on average realization. There are also the coal-cleaning problem; increased capital investment, maintenance, obsolescence, and the relation of all these to the spread between realiza-tion and production cost. If coal seams were uniform, the answer would

Jan 1, 1939

By M. F. Smith

BELOW the nose of the bainitic C curves in isothermal transformation diagrams, the rate of the austenite-to-bainite transformation usually decreases with decreasing temperature. However, in some steels and iron-carbon alloys, there is a noticeable acceleration in the initial reaction rate at temperatures just above Ms. Such speeding-up of the bainitic transformation would be understandable at temperatures just below Ms because of the catalytic effect of the martensite formed,' but the reversal in isothermal kinetics just above Ms seems quite anomalous. This behavior was observed by Howard and Cohen' in a 1.35 pct C steel and, on the basis of metallo-graphic examination, it was attributed to the formation of a thin plate-like product not belonging in the bainitic sequence. More recently, schaaber2 found two-stage reactions occurring in the vicinity of Ms in a number of steels, and suggested that the first stage might be the isothermal formation of marten-site, preceding the isothermal formation of bainite in the second stage. A decrease in the bainitic incu-

Jan 1, 1960

By J. S. Levine, M. Prats

Several methods are available for calculating the performance of solution-gas-drive reservoirs from the PVT properties of the oil and from the relative permeability and other properties of the formation. These methods require a number of simplifying assumptions. The present method of computation has made use of a high-speed computer to solve simultaneously the nonlinear partial differential equations that describe two-phase flow by solution-gas drive in order to calculate the performance of a reservoir. Some of the results obtained by the nonlinear partial differential equation solution are compared with those obtained with an approximate method, which has been called the semisteady-state solution. The pressure and saturation profiles from the wellbore to outer boundary calculated by the two methods are compared for one constant-terminal-rate case and two constant-teminal-pressure cases. The agreement in these profiles, as well as in the values of average reservoir pressure and cumulative recovery, leads to the conclusion that, for most engineering calculations, the semisteady-state method will give a reasonable approximation to the numerical solution of the differential equations describing solution-gas drive. An unfavorable (as regards ultimate oil production) set of relative permeability curves was used in the calculations in the belief that the effect of the parameters which were studied would be emphasized to a greater degree. Furthermore, the reservoir was assumed to be completely homogeneous, and these results should not be considered applicable to any other type of reservoir. Gravity effects are not considered. The absolute permeability was varied from 25 to 0.5 md. At an economic limit of 2 B/D, the recovery for a 25-md reservoir is about 1.8 times as great as that for a 0.5-md reservoir. The effect of permeability on the producing gas-oil ratio is minor. Once PVT properties of the oil and the relative penneability properties of the reservoir are fixed, the pro- during gas-oil ratio is found to be a function of the fraction of oil recovered. Well spacings of 10, 40 and 80 acres were considered. For the assumed homogeneous-reservoir properties, the effect of spacing on recovery at an economic limit of 2 B/D was very slight. Certain dimensionless groups can be used to extend the results to other fields having different penneabilities, spacings, reservoir thicknesses, well radii and porosities, so long as the PVT and relative permeability properties are similar to those used in this paper. INTRODUCTION An important aspect of reservoir engineering is the prediction of the performance of the reservoir based on the limited information normally available early in the life of a field. Usually, soon after a field has been discovered, it is necessary to decide upon the spacing to be employed and the production program to be used for most efficient utilization of reservoir energy. Where these decisions have not been dictated by legal or political considerations, they have frequently been based on experience factors which indicate that two fields with similar characteristics will probably have similar performances. To the extent that the industry has been successful in economically exploiting oil reservoirs, this rule-of-thumb method has been found to have merit. A large amount of theory has been developed with which it is possible to predict the performance of a reservoir by using certain known properties of the oil and the formation. Because of the difficulties of the mathematics involved for a drainage area having square or rectangular boundaries, the problem usually has been simplified and idealized by assuming each drainage area to have radial symmetry and the field to be represented by a number of these drainage areas. Muskatl was one of the first to formulate the theory for two-phase flow and to solve the equations for a few cases by numerical integration, using the relatively slow means of computing available at that time. His equations describing

By H. H. Stoek

Among the mining and metallurgical achievements of the latter part of the nineteenth century, not the least is the incep tion and successful prosecution by mining men of a technical educational movement which in magnitude surpasses any similar movement ever before set on foot. The following account of this undertaking has been prepared at the request of the Secretary of the Institute :*

Jan 1, 1899

By R. R. Sayers

Ventilation may be defined as the process by which vitiated air of an enclosed or partly enclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level Per Cent. Oxygen.................................................. 20.94 Nitrogen................................................. 78.09 Carbon dioxide........................................... 0.03 Argon................................................... 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxide, ammonia, ozone........................................ traces Carbon Dioxide Limit For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent, carbon dioxide. Nevertheless, in mines it sometimes occurs in sufficient quantities to cause symptoms in men or even unconsciousness and death. One-half of 1 per cent. of carbon dioxide in normal air causes a slight and unnotice-able increase in the ventilation of the lungs, that is, a man exposed to one-ha,lf of 1 per cent. of carbon dioxide will breathe a little deeper and a little faster than when in pure air. If 2 per cent. of carbon dioxide is in the air, the lung ventilation will be increased about 50 per cent.; if there

Jan 1, 1927

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By D. Turnbull, R. E. Cech

Small particles, 10-20 microns diameter, of a 28.6 atom pct nickel, balance iron alloy, have been supercooled 186 C with respect to bulk alloy M, temperature. Particles exhibit a marked mechanical shock sensitivity while being held in a supercooled state. The tendency for shock to induce martensitic transformation appears to be a maximum at —140 to —160°. Slow cooling of particles in mechanical contact with one another results in extensive martensite formation. This is prob-ably the same effect as the catalytic effect observed in polycrystals where martensite formation in one grain induces transformation in other grains. AS a result of extensive research over the past decade on the martensitic transformation, a much better though not complete understanding of the transformation has resulted. Recent reviews by Bilby and Christian' and Kaufman and Cohen2 have

Jan 1, 1959

By Miles L. Silberman, Edwin H. McKee, John H. Stewart

Three, major suites of igneous rocks were erupted in the Great Basin in middle and late Cenozoic time. The first resulted in eruption of andesitic rocks in the northern Great Basin between 42 and 34 m.y. ago. Between 34 and 17 m.y. ago this igneous activity migrated to the southwest, ending about 17 m.y. ago with the onset of crustal extension and north-south- trending Basin and Range (rift) faulting. The second volcanic suite erupted between 17 and 8 m.y. ago in the northern Great Basin. The third volcanic suite consists of andesitic and rhyolitic lavas and some basalt erupted between 22 to 7 m.y. ago in the western Great Basin along the northwest transcurrent Walker Lane fault zone. Hydrothermal ore deposits are associated with all suites of igneous rocks.

Jan 1, 1977

By S. Harries Daddow

THE INSUFFICIENCY OF PILLARS OF COAL FOR THE PURPOSES DESIGNED-THE FRUITFUL CAUSE OF DANGER, EXPENSE, AND WASTE-THE PROOF OF INSECURITY-SUBSTITUTE FOR PILLARS OF COAL-PILLARS AND PANELS COMPARED. PILLARS of coal, which are designed and left in our mines as the means of supporting the overlying strata of our coal-beds, and securing protection to the miner, are not only insufficient for these purposes, but the most objectionable means of providing the desired security to life and property. Though such pillars are left at a great sacrifice to the owners of collieries and mineral lands, loss to the resources of the commonwealth, and ultimate privation to the public, they defeat the very ends for which they are designed, and not only do not secure life and property, but are as fatal to the one as ruinous to the other. Propositions.-It is eminently desirable that the resources of the commonwealth-particularly our mineral wealth in anthracite coal, which is limited-should be carefully utilized and made available, not only to ourselves but our posterity. Yet, speaking as an anthracite miner, we are wasting our resources of coal with a recklessness which will bring ruin in the end, unless checked, not only to the iron manufacturing interests of the East, whose chief protection, in competition with the iron-masters of the interior, lies in a cheap and abundant supply of anthracite furnace fuel, but to the best interests of the State. It is, consequently, not only desirable, but necessary, that we should realize every ton of coal from each colliery, and every acre of coal area, in order that our resources may not be wasted at present, to breed want in the future, and to realize the greatest present benefit to the mine, the miner, and the public. It is not possible, however, to secure these ends, if we continue to leave, as we do at present, from one-third to one-half our resources in anthracite as pillars in our mines. But our sad bills of mortality, our abandoned collieries, and our yawning mountain-sides, present ample evidence that even this enormous waste of coal, though left for the purpose of protecting life and property, is as totally inade-

Jan 1, 1873

By H. C. George

IN 1901, the United States produced 69 million barrels of crude oil, which was 41.4 per cent of the world production. By 1931, these figures were 850 million barrels and 62.1 per cent respectively, showing over this period of thirty years an increase in the world production of 718 per cent. Over this same period, the increase in the demand for technically trained men in the industry was much greater than the increase in crude-oil production. This was because much of the increase in production was secured by the application of geology and physics to the finding of new oil fields and by .the development of engineering methods and equipment incident to drilling and producing from much greater .depths.

Jan 1, 1934

By R. S. Archer

In the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the hcat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis, heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while in others, especially in those whose grain is unusually fine or in which the final hardening heat has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters. The properties of the steel are as follows: Carbon, per cent............... 0.42 Brinell hardness.............. 293 Nickel, per cent................ 1.35 Yield point, pounds per square Chromium, per cent............. 0.90 inch........................ 131,000 Copper, per cent................ 0.025 Maximum strength, pounds per Manganese, per cent............ 0.74 square inch................. 144,500 Phosphorus, per cent............ 0.024 Elongation in 1 in., per cent... 28 Sulfur, per cent................ 0.036 Lod impact, foot-pounds...... 51 Reduction of area, per cent...... 57.3

Jan 1, 1920

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

Jan 1, 1967

By J. P. Timmons, J. H. Moran, G. K. Miller, M. A. Coufleau

A prototype equipment has been designed and built for the digital recording of well logs on magnetic tape at the same time that the regular film recording is made. The format of the digital tape produced is such that it can be used directly at the input of the ZBM 704, 7090 or other models of ZBM computers which accept digital magnetic tape. This apparatus has been used for the experimental field recording of dipmeter tape logs which were subsequently computed by means of an ZBM 704 or 7090. In this paper the equipment and the digital tape are described briefly, and their application to the computer-interpretation of dipmeter data is discussed. A principal element in the interpretation of the dipmeter log is the correlation of the three microresirtivity dipmeter curves to determine the depth displacements between them. Several correlation methods for computer use are considered, with particular attention to their sensitivity to error and their consumption of computer time. The tape data were used to compute information content of the dipmeter microresistivity curves in terms of their frequency spectra. The results show that the sampling rate used in recording the digital information is quite adequate and illustrate a use of the digital tape in evaluating the characteristics of new tools. Some examples of field results are shown. It can be foreseen that, when digital tape recording becomes available for general field use, a whole new realm of possibilities will be opened up for the processing of other well logs through computations, which hitherto were not feasible because they were too laborious and time-con.sunzing. INTRODUCTION The last few years have seen a revolution in the design and production of data-processing equipment. Stored-pro-gram digital computers have progressed from a research curiosity to the basis of a major industry. There are now hundreds of such machines in daily use in the United States. With the acceptance of a technique that was, in fact, already clearly described by John von Neumann in 1945, the last decade has seen great strides in the development'of components, reliability, programming systems and, most spectacularly, in the sheer number of machines built and in use. In 1957 there were enough digital computers available to the oil industry to justify the suggestion that it would be worthwhile to investigate the possibility of using these machines in processing well log data.' The first result of this investigation was the appearance of what may be referred to as the input-output bottleneck. Well logs are customarily recorded on film. To get these data into a machine required then (and still does): a time-consuming semi-automatic reading of the film; conversion of the log data to digital form; and recording these digital data in some medium acceptable for computer input, such as cards, magnetic tape, or punched paper tape. However, the recording, reading, and re-recording could only result in deterioration of the data. Therefore, it was concluded that the fist step should be the development of a new, more direct recording technique supplemental to the film recording, which would provide easy access to the digital computer. There are many solutions to the problem of recording log data in an easily recoverable form. After careful consideration it was decided to adopt the boldest solution which, it was felt, was also the most elegant. It was decided to record well logs directly, in the field, on magnetic tape in such a way that this tape could be used without further modification as an input to the IBM 704 or 7090 computer. To realize practical field recording of magnetic tape logs, it became necessary to develop in a rather small package, an analog-to-digital converter, a tape recorder, and the necessary multiplexing and control circuits to allow the simultaneous recording of a multiplicity of logging signals. The magnetic tape recording was to be made simultaneously with the conventional logging operation in such a way as not to interfere with it. Along with the development of hardware, it was necessary to begin development of interpretation techniques and machine programs that would exploit the power of the digital computer. Here, again, there is a long list of possible applications. After much consideration it was decided to concentrate on the interpretation of the dipmeter log as a first application. It is the object of this paper to describe in some detail the developments sketched in the last three paragraphs.