Search Documents

By Alex McCoy

SAMPLING of the fluid from oil wells for percentages of oil, emulsified oil, and water during the last two years has brought out some interesting facts concerning oil-water emulsion. This result led to a laboratory investigation of emulsion, which substantiated the conclusions made from the field observations. The purpose of this paper is to present the information collected, the laboratory experiments, and our interpretation of the same. In order to define emulsified oil exactly, give its synthesis and origin, and to show how and when it is formed in the wells, the work was necessarily divided into two separate lines-laboratory work and field observations. It is hoped that this study may lead to a discussion of such points so that the petroleum engineer, geologist, or technologist may be benefited by its practical bearing on oil-field management. Special credit is due Mr. Everett Carpenter, chief geologist of the Empire Gas & Fuel Co., for his assistance and cooperation in this work. LABORATORY INVESTIGATIONS ON EMULSIFIED OIL Laboratory investigations were conducted in an attempt to learn the composition and some of the properties of emulsified oil, or B. S., as it is more commonly called, also to demonstrate, by laboratory methods, how B. S. may be formed under conditions similar to those existing at the time a well is being pumped, and how it may be broken down. Literature bearing on this subject is widely scattered and very limited in scope. Bacon and Hamor define B. S., or bottom settlings, as "earthy matter, inert organic matter, or, in the case of Pennsylvanian petroleum, an emulsion of paraffin wax and water, which accompanies crude oil." In this discussion we will limit the term B. S. to that heavy,

Jan 8, 1919

By Charles R. Fettke

BefoRe the Drake well on Watson Flats below Titusville, Pa, inaugurated the modern petroleum industry on Aug. 28, 1859, a considerable industry, based on the manufacture of mineral oils through the destructive distillation at relatively low temperatures (750' to 800' F.) of cannel coals and shales in closed, air-tight retorts, had already sprung up in Europe and America because of the increasing cost of animal and vegetable oils and fats and the growing demand for illuminating and lubricating oils. In 1860, eight out of 55 such coal-oil companies in the United States had plants located in Pennsylvania.' Of these, the Lucesco Works, costing $120,000, situated near Kiskiminetas Junction, was the largest operating in the country. It was equipped with 10 revolving 2.5-ton retorts and 16 stills for rectifying the oil, each holding 2000 gal. The total output of crude oil was almost 6000 gal. per day.2 The discovery of an abundant supply of natural petroleum by the Drake and other wells stopped the distillation of coal oil in America. Most of the smaller plants were closed and others were converted into petroleum refineries. At present, in spite of the temporary over-production of petroleum, the coal and oil-shale carbonization industries are again attracting the attention of far-sighted oil companies who realize that the gradual exhaustion of the American petrol-

Jan 1, 1923

By Charles R. Fettke

BefoRe the Drake well on Watson Flats below Titusville, Pa, inaugurated the modern petroleum industry on Aug. 28, 1859, a considerable industry, based on the manufacture of mineral oils through the destructive distillation at relatively low temperatures (750' to 800' F.) of cannel coals and shales in closed, air-tight retorts, had already sprung up in Europe and America because of the increasing cost of animal and vegetable oils and fats and the growing demand for illuminating and lubricating oils. In 1860, eight out of 55 such coal-oil companies in the United States had plants located in Pennsylvania.' Of these, the Lucesco Works, costing $120,000, situated near Kiskiminetas Junction, was the largest operating in the country. It was equipped with 10 revolving 2.5-ton retorts and 16 stills for rectifying the oil, each holding 2000 gal. The total output of crude oil was almost 6000 gal. per day.2 The discovery of an abundant supply of natural petroleum by the Drake and other wells stopped the distillation of coal oil in America. Most of the smaller plants were closed and others were converted into petroleum refineries. At present, in spite of the temporary over-production of petroleum, the coal and oil-shale carbonization industries are again attracting the attention of far-sighted oil companies who realize that the gradual exhaustion of the American petrol-

Jan 1, 1923

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of March, 1913 BAECHTOLD, CHARLES A., Engr 9G Liberty St., New York, N. Y. BRANTLY, JOHN E., Instructor in Geology Tuscaloosa, Ala. CADDY, JAMES P., Net., ,Lake View & Star, Ltd Fimiston, West. Australia. LONERGAN, PHILIP J., JR., Prof. of Mining, Government University, Peking, China. MCKANNA, EDWIN A., Min. Engr P. 0. Box 834, Oklahoma City, Okla. MACDONALD, ANGUS W., Supt. Labor Dept., Dominion Coal Co., Ltd., 21 Queen St., Sydney, N. S., Canada. TSUBOI, Yoshio, Min. and Met. Engr., Kosaka Mine, Fujita Co., Akita-ken, Japan.

Jan 4, 1913

By William E. Newman

When Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great and the tonnage was small, but on the other hand the results were fairly satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Rozan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process. The Luce and Rozan process has persisted in its original form to the present day. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process. Out of many schemes he decided that this could be accomplished by placing the Luce and Rozan kettles upon hydraulic rams so that each

Jan 1, 1918

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper .to, discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in. brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: 1-gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2-liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3-glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4-crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that carried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant, contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.1 At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1-aqueous solution, a much more expansible liquid, and a gas; 2-aqueous solution, salt crystals, and a gas; and 3-the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20° and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.2-6 Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid. carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.7,8 Hartley (1876, 1877),9,10 Hawes (1881),11 Wright (1881),12 Johnsen (1920),13 and Holden (1925)14

Jan 1, 1952

By D. Harrington

During the past few years, there has been a trend toward the use of rock-dusting, rather than relying on humidifying, or the use of water, to limit or prevent explosions in the coal mines of the United States. This is partly because British coal mines have adopted rock-dusting and, at least in a sense, have condemned the use of water. Moreover, during the past few years, particularly in the latter part of 1922 and in 1923 and 1924, several explosions with heavy loss of life occurred in coal mines of the United States that were known to have more or less extended sprinkling, or humidifying, systems. The sentiment created by these disasters quickly caused a distrust of explosion-prevention methods requiring use of water and simultaneously caused more or less of a stampede into rock-dusting. Much of the wholesale condemnation of watering methods was without adequate knowledge, or at least without adequate consideration, of local conditions in each case, and rock-dusting was adopted largely without sufficient knowledge of how to rock dust safely or correctly. However, mines that had been using watering methods and had suffered these recent serious disasters (notably Dolomite, Dawson, and Castle Gate) instead of abandoning the use of water when operations were resumed after the disaster, greatly extended their watering systems. At the same time they took other precautions as to electricity, ventilation, blasting, etc., and supplemented the watering system with rock-dusting where the latter was likely to be the more effective. The trend toward rock-dusting during the past year or two (succeeding the recent mine disasters) is very similar to the rapid movement toward watering, or humidifying, methods, about 1910 to 1912, after a series of disastrous mine explosions. The Phelps-Dodge Corpn., which operates a large property at Daw-son, N. M., after an explosion in its No. 1 mine in February, 1923, decided that it is dangerous to have all its "explosion-prevention eggs in one basket" and so adopted what may now be termed the Western coalmine explosion-prevention system, in which both rock-dusting and watering are used, supplemented by other up-to-date mining methods and practices; such as exclusive use of modern electric safety lamps, with magnetically locked flame safety lamps for testing purposes; use of

Jan 1, 1925

By C. S. Brooks

Several of the commonly used methods for deter-mination of effective grain densities of minerals have been evaluated for accuracy and precision, and their applicability to various types of petroleum reservoir minerals tested. Consideration was given to the effect of consolidation, swelling clay, and wettability on these grain-density determinations. Procedures with helium displacement, a modified low-pressure Boyle's law porosimeter, and liquid displacement (water, n-decane, and n-octanol) were tested. The helium-displacement procedure was used primarily as an independent reference for which the effects of fluid-solid interaction, e.g., adsorption and wettability, were negligible. The procedures with the Boyle's law porosimeter and with liquid displacement are the methods in common use. Minerals investigated included calcite, West Texas limestone core samples, California sandstone core samples, and Wyoming bentonite. The number of samples tested, while not large, was adequate to permit application of statistical methods. Grain-density measurements on calcite (Iceland spar) provided a basis of comparison for the accuracy and precision of the procedures under investigation for a material with a high degree of chemical and physical homogeneity and for which fluid-solid interactions were at a minimum. Liquid-displacement procedures (water or n-decane) provided the greatest reliability and precision for measurement of the grain densities of the limestone tested. Gas-displacement procedures (helium or Boyle's law porosimeter) provided the greatest reliability and experimental convenience, if not the greatest precision, for the measurement of the grain densities of the swell- ing clay, Wyoming bentonite, and the shah sandstones which -contained appreciable amounts of swelling, in-terstitial clays. These experiments were designed to evaluate the applicability of the grain-density procedures in common we to some of the less tractable minerals—tight limestones, shaly sandstones, and swelling clays. The results should provide a useful basis for a selection of the method most suitable for application to the various petroleum reservoir minerals encountered and especially for use in the estimation of formation porosity. INTRODUCTION These experiments were undertaken to evaluate the accuracy and precision of several commonly used methods for determination of effective grain densities of minerals, and to test their applicability to various types of petroleum reservoir minerals. Consideration was also given to the effect of consolidation, clay, and wettability on these grain-density determinations. Procedures used included measurements with helium displacement, with a modified low-pressure Boyle's law porosimeter, and with liquid displacement (water, n-decane, and n-octanol). The minerals investigated included calcite, West Texas limestone core samples, California sandstone core samples, and Wyoming bentonite. The accurate determination of the porosity of petroleum reservoir formations, in particular those of low porosity, has received much attention. Both bulk-volume and grain-volume measurements necessary in the evaluation of porosity have been examined by many investigators with the objectives of improving both the accuracy and the precision of these determinations. In this investigation statistical criteria for selection of the most reliable and suitable procedure for use with a given type of mineral are demonstrated. The grain-volume measurement procedures appear to be the most susceptible to improvement.

Jan 1, 1958

Manganese ore from the Black Rock, Kramer, and Black Jack mines in Tooele and Jaub Counties, Utah, are of acceptable grade, the U. S. Bureau of Mines has announced. Payment of a premium price of 252¢ per lb to the Copper Range Co., of Michigan for the output of its White Pine mine, has been agreed to by the DMPA. The contract will be limited to $28.6 million worth of copper. The agreement follows an RFC loan grant of $57 million to bring the White Pine property into production within three years. Increases of 5 to 6 cents over the Lake copper ceilings have been granted to the Calumet & Helca Consolidated Copper Co., for operation of "high cost" deposits, according to Jess Larson, DMPA administrator. Mr. Larson expects the move to add about one million lb of copper per month to the supply. The agreement can be cancelled on 60 days notice and is terminated automatically in the event copper ceilings are removed.

Jan 1, 1952

By P. L. Raffo, T. E. Mitchell

Single crystals of Ta-Re alloys have been deformed in tension and compression as a function of solute concentration and temperature. The temperature dependence of the yield stress is decreased by alloying. At low temperatures there is a minimum in the yield stress (at about 2 at. pct) as a function of concentration. Three-stage hardening was not observed in the alloys. Linear hardening rates, where observed, were characteristic of stage II in pure tantalum. At low temperatures and high concentrations, work softening was often prominent at high strains. Electron microscopy revealed that dislocations are mostly of screw orientation, although heavily jogged and cusped, and often occurring in dipole pairs. The alloys become more prone to cleavage with increasing rhenium content, due mostly to an increasing yield stress rather than a change in cleavage strength. Alloying apparently decreases the Peierls stress of bcc metals at low temperatures by facilitating kink nucleation at solule atoms on screw dislocations. Higher solute concentrations further increase the yield stress. Quantitative calculations and comparisons with other bcc alloy systems are made to show that the predominant hardening mechanism is due to the interaction of dislocations with misfitting solute atoms close to their slip planes. The interaction is so localized that the core dilatation of dislocations could be important. CONSIDERABLE interest has arisen in recent years concerning the mechanical properties of unalloyed bcc metal single crystals.'-7 These and similar studies on polycrystalline materials have resulted in a considerable understanding of the macroscopic yielding characteristics8, 9 and the process of work hardening.'' This latter advance is due in a large part to the increased use of transmission electron microscopy in P I RAFFO junior Membar AlMF is Metallyureist Iewis such studies and the general observance of three stages of work hardening in the shear stress-shear strain curves. The properties of substitutional alloy single crystals of bcc metals have not been determined in as much detail as in the pure metals. Insufficient systematic studies have been made on the effect of alloying on the magnitude and temperature dependence of the yield stress or the stress-strain curves. The alloy systems which have been studied to some extent have been Ta-W,11, 12 Ta-Mo," Ta-Nb,12'14 Mo-Re,15 W-Re,16 and alloys of iron with nickel,17 platinum,17 vanadium,18 and aluminum.18 A large body of data exists on Fe-Si alloys, but these have mainly been a result of the experimental convenience of using this material in place of unalloyed iron, rather than a comprehensive study of the mechanical properties of the alloy system per se. The present authors have previously reported additional data on the properties of Ta-Re, Ta-W, and Ta-Mo alloy single crystals.1g Some of the data on Ta-Re alloys will be described later in this paper. Briefly, single crystals of Ta-Re (1.2 to 10.6 pct), Ta-W (6.2 and 10.2 pct), and Ta-Mo (2.9 and 9.0 pct) were grown by the floating zone method in vacuum. Compression tests were performed in the temperature range 77" to 623°K. Slip was found to occur in Ta-Re alloys at 77' and 298°K on the (~ll)[lil] system and slip lines were coarser and straighter than in unalloyed tantalum. No three-stage hardening was observed in any of the alloy systems and the curves were nearly parabolic. At temperatures above 175°K the yield stress* increased monotonically with in- creasing composition while at 77" and 175°K the yield stress initially passed through a minimum after which it began to increase again for concentrations greater than about 2 pct Re. Similar minima were observed in Ta-Mo alloys and to a lesser extent in Ta-W alloys. The minimum was interpreted as being a result of a

Jan 1, 1969

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By R. H. Frazier, C. H. Lorig, F. W. Boulger

This investigation establishes the effect of ferrite grain size resulting from various heat treatments on the transition temperature of a semikilled steel plate. Different austenitizing temperatures and various cooling rates were used. The ductile-brittle transition temperatures were determined by the Navy tear test and the keyhole Charpy test. THE data presented in this paper deal with quality characteristics of ship-plate material which were investigated in a research project sponsored at Battelle by the Bureau of Ships, Dept. of the Navy. Specifically, the object of this investigation was to establish the effect of ferritic grain size (resulting from various heat treatments) on the so-called transition temperature of ship-plate steel. Transition temperature is not a fixed property of steel. It is derived from a series of static or dynamic tests made at various temperatures and is qualified by specifying the type of test employed as well as the testing criteria. Because in earlier investigations of ship-plate quality1,2 the so-called Navy tear test and standard notched-bar tests (keyhole Charpy) proved to be useful in interpreting instances of brittle behavior of ship plate in service, these tests were used in the investigation reported in this paper. By definition,' in the Navy tear tests the highest temperature at which one or more of four specimens breaks with a brittle fracture (that is, when less than 50 pct of the fracture area has a dull fibrous texture) is termed "transition" temperature. In the Charpy tests, the 12 ft-lb level of energy absorption was used as a criterion indicating the "transition" temperature, although other levels of energy absorption were also used for comparison. Earlier work" on ship-plate steels indicated that the temperature at which ship plate is finished has a very significant effect on its notched-bar properties. Plates rolled in the laboratory, where the finishing temperature can be carefully controlled, showed a 16°F decrease in tear test transition temperature when the finishing temperature was lowered 200°F (from X" to Y°F). The same plates showed a drop of 10°F in the keyhole Charpy transition temperature from the same decrease in finishing temperature. Commercially finished plates' exhibit a similar trend. When the ferrite grain size of the hot-rolled laboratory plates was determined, a close relationship was found between the ferrite grain size and the notched-bar transition temperature." " he indicated relationship between grain size and transition temperature was in agreement with the findings on low carbon steels of Hodge, Manning, and Reichhold' despite the differences in composition of the steels. The cooling rate after rolling varies from one steel plant to another. This variation changes the micro-structure" and appears very likely to affect the notched-bar properties of the steel plates. In the investigation summarized in the present paper, heat treatments simulating finishing practices in the hot rolling of ship plate were used in order to vary the ferritic grain size. It is believed that the indicated relationship between grain size and transition temperatures of the ship-plate material will prove useful in estimating the effect of rolling temperature and of cooling rates from rolling temperatures on the notched-bar properties of semikilled steel plate. Material The semikilled steel plate used in this investigation was a ¾ in. hot-rolled plate from an open hearth heat. Other plates from this heat have been used on many other studies performed for the Ship Structure Committee," "," and the heat has been identified as project steel "A". The chemical composition of the plate1 was 0.25 pct C, 0.49 pct Mn, 0.011 pct P, 0.045 pct S, 0.04 pct Si, and 0.004 pct N.

Jan 1, 1956

By G. A. Reinhardt, Albert Sauveur

Although many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel; that is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes marten-sitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line MO—and it remains martensitic or austenitic after slow (air) cooling.' We have in this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening; Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it

Jan 1, 1913

By J. Kent Smith

VANADIUM is generally spoken of as a rare element; but, even in the light of our resources as known a couple of years ago, this description could be accepted in a qualified sense only. In fact, vanadium is very widely distributed, being a constituent of most clays, while even caustic soda has been shown to contain almost regularly a minute proportion of it, although the quantity in each case is so small as to render impracticable the extraction of the metal there from with profit. The opening-up of a large deposit of vanadium sulphide ore in South America has put a new phase on the commercial outlook of vanadium, the technical value of which for the improvement of steel has been proved by rigorous scientific investigation.

Sep 1, 1907

By Wolfgang O. Gluschke

INTRODUCTION Virtually all countries have general legislation covering most aspects of mining and mineral processing, including investment and tax laws, safety and health regulation, and specific rules applying to exploration reporting procedures. Yet most developing countries negotiate individual agreements with foreign investors for major mineral projects, in particular when all or part of the expected output is exported. Such agreements are known under several different names, as for example concession agreement; technical assistance agreement or service contract; management agreement; production sharing contract; joint venture; or contract of work. The objectives and conditions governing such contracts are as diverse as these titles are. While a mining project is only one among a large mumber of similar undertakings in industrial countries, in most developing countries such projects usually have a dominating position within the country's economy. The general legislation is often inadequate and insufficiently detailed to cover all aspects of large projects with extensive foreign inputs and international markets. Therefore, the need for specific arrangements. Specific arrangements may also become necessary due to the complexity of markets for mineral products, the large number of participants - equity partners, suppliers, financial institutions, buyers, etc. - or economic and political conditions in the host country and fiscal regulations in the home country of the investors. Most agreements are concluded between governments, or government agencies, in developing countries and private industry headquartered in developed market economies - Canada and the United States of America in North America, Western European countries, Japan, South Africa and Australia - or, in some instances, with state-owned firms in these countries. There are fewer agreements between developing countries and the centrally planned economy countries - Eastern Europe and the USSR - which cannot be considered here because of absence of adequate information. Agreements can be concluded at any of the different stages from exploration through closing of a mine. While most contracts are negotiated at the time when a potentially viable ore body has been delineated and investigated sufficiently to anticipate a realistic time for commencement of production, other agreements start with "grass-roots" exploration, during operation of a mine, smelter or refinery or, exceptionally, after a temporary shutdown. While several major provisions are included in all types of agreements, others are covered in much more detail (or not at all) in some contracts reflecting the specific work programme of each project. While it is realized that subdivision and classification of complex contractual relations is necessarily arbitrary to a certain extent, such grouping is useful in practical terms, especially for the non-specialist. The following discussion, therefore, will start with a description of the major forms of contractual relation - concession, investment contract, joint venture, management agreement, service and production sharing contracts. Major issues covered in all, or almost all, agreements will then be dealt with. These include stages of development, corporate structure and control, fiscal arrangements, infrastructure development and environmental law, and dispute settlement and renegotiation. FORMS OF CONTRACT RELATIONS There has been marked change in the type of agreement entered into during the 1960s (and before) and the early 1970s and the period thereafter. While straight "concessions" - granting of exclusive rights to foreign investors over a certain deposit or areas with little restriction or well-defined obligations - were the rule during the first half of this century, more complex agreements have evolved since. Some of these cover every conceivable aspect, foreseen or only possible, and define rights and obligations of all partners to the last detail. Over the years, agreements have without doubt become more beneficial for the developing host countries, in part as a result of well-publicized nationalizations, as for example in Chile, and in part due to changed attitudes in all countries

Jan 1, 1985

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By J. S. Ross

Few Canadians realize the role of their domestic industrial minerals industry because it is over-shadowed in production value by a large metallic minerals industry. But since 1960, Canada has had a reasonably well balanced, mature industrial minerals industry; and although the nation's sparsely scattered population has not been able to support an industrial minerals industry in a manner comparable to the domestic and foreign support given the metal mining sector, Canada is, nevertheless, exporting large quantities of higher priced nonmetallic minerals. Production of many of the basic minerals had been firmly established long before 1960, but it was not until the late 1950's that the output of cement, salt, titanium dioxide pigment and slag, sulfur, gypsum and sodium sulfate reached relatively high levels. Shortly after 1960, the significant potash and lithium chemicals industries were established and their effect is just now being realized.

Jan 11, 1964

By A. E. Beasley, Ike McKinney

Scale is a broad term which includes many types of mineral deposits which have limited solubility in water. These mineral components precipitate when combinations of scale-forming cations and anions exceed their solubility. Scale deposits are tightly bound to each other and to the metal surfaces of a water system. Precipitates that do not readily adhere to each other or to metal surfaces are known as sludges. Sludges are easily removed from a system by flushing. For example, a sludge is formed in the internal treatment of boiler waters with orthophosphates where the calcium is purposely precipitated as hydroxyapatite. Calcium phosphate would have a tendency to adhere to the boiler tubes except for the addition of tannins or lignins. These sludge conditioners maintain the precipitated calcium phosphate as a sludge which can be readily removed by boiler blowdown.

Jan 3, 1973

By E. F. Kingsbury

One of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consiimption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. Substitutes for Platinum During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper matcrials, and the other, the dcveloprnent of materials of superior electrical performance. The merit of a contact metal has been assumed to be dependent on its infusibility, and since thc more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were