Search Documents

By J. M. Hodge, M. A. Orehoski

It is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "harden-ability " should be high enough to suppress all transformation except that to martensite under the heating and quenching conditions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,' does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point). Furthermore, in plain carbon steels or in steels of low hardenability, the difference in hardenability expressed in

Jan 1, 1947

By H. E. Gross

Recently, areas of abnormal rock pressure have been drilled on the Gulf Coast of the United States. These pressures may be caused by the recent and pronounced raising of some of the structures without loss of the formation pressure that existed when the reservoir was developing and the producing sand much more deeply buried. It is possible also that a permeable fissure may connect a shallow accumulation of gas with the gas cap of a much deeper reservoir of oil, gas and water. The pressures are so great that dependence on blowout-prevention equipment alone is hazardous to life and property. Fortunately, wells with excessive casing-head pressures, such as the Stanolind Oates No. 1 of the South Houston field, an 8700-ft. gas well with 6000 Ib. per sq. in., and the near-by Stanolind Candelari No. 1, and 8100-ft. gas well with 5000 Ib. per sq. in., have not blown out and cratered. A case is on record of drill pipe in a well in Harris County, Texas, (Oates No. 1) rotating for 8 hr. through blowout-prevention rams holding a back pressure of 2900 Ib. per sq. in. at the casinghead after the mud was altered by salt-water intrusion. Such conditions warrant the use of extremely heavy muds having low viscosity, made from galena (PbS) or specially prepared mixtures of hematite (Fe²O³) and galena suspended by bentonite. In some Gulf Coast wells, sodium silicate mixed with concentrated brine is used to drill through heaving shale formations. Such a fluid inhibits heaving remarkably, but it is expensive and costs as much as $10 per barrel. Barite has been used to weight this mixture. However, this mineral too rapidly increased an already excessive viscosity and it was thought that galena might be better for weighting such drilling fluid. The operator was anxious to try the latter, but none was available in the district. Laboratory Study of Heavy Muds To foster the use of the plentiful and extremely heavy mineral, galena, research has been done recently at the University of Oklahoma to determine the mud-making properties of this substance. For comparative

Jan 1, 1938

By E. F. Kern, W. W. Loo

A review of the literature on the reduction of cassiterite showed that scarcely any progressive changes were made in the methods of reducing cassiterite until within the last two decades, and that during that period many improvements in the metallurgy of tin have taken place. Since 1914 the world's consumption of tin has increased considerably, resulting in the exploitation of primary tin deposits such as the Bolivian lode, which has become an important source of tin. On account of the low tin content of Bolivian ore, and the presence of objectionable impurities of the reduced tin, the smelting of this ore and the refining of the tin has changed considerably from the methods formerly used. A comparative study of the methods of smelting cassiterite concentrates suggested that an investigation be planned so as to determine what factors effect the extraction of tin from its ores by reduction with carbon. The first part of the experimental work was the determination of whether roasted cassiterite concentrates can be reduced by carbon without the use of flux, and the reduced pellets of tin be collected into a single mass separate from the dry gangue residue. The second part of the experimental work was a comparison of the effect of variations of the different factors on the smelting of roasted cassiterite concentrates: first, the effect of varying the composition of the slag; second, the effect of varying the amount of reducing agent; third, the effect of varying the relative amount of the resulting slag; and fourth, the effect of different kinds of reducing agents. Review of Literature Experiments on the smelting of Bolivian tin concentrates were made by James P. Gill in 1920 in the metallurgical laboratory of the School of Mines, and submitted as a graduate thesis. The results of these tests are fully reported as they are preliminary to the experimental part of this paper, and also because they have not been published. The variables investigated by Mr. Gill were: (a) the effect of temperature on the rate of reduction of cassiterite concentrates; (b) the time required for

Jan 1, 1928

By P. Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occurring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, Calif. recovers potash from natural brines, but uses fuel to accomplish evaporation. Solar evaporation is always desirable, because of low costs, however artificial evaporation may be economical if a group of very valuable salts are recovered. This is the case for the American Potash operations at Trona. Solar evaporation is limited by low working temperatures, which in most areas of the world is between 18 and 45°C. In many cases the average working temperature is about 25°C. However, solar evaporation will have to accommodate itself to the highs and lows of each 24 hour period, and to the different average temperatures during the months of the year. Therefore, solar evaporation, although more economical than artificial evaporation, has a tem- perature limit which greatly reduces the chances of its application. The feasibility of solar evaporation as a means of recovery of values from a particular brine, may be evaluated by the use of phase diagrams showing the several components present. This paper is restricted to the five component system: C1-, SO4=, Na+, K+, Mg++, and H2O, which correspond to brines found at Wendover, Utah, the Great Salt Lake, and sea water bitterns. THE BONNEVILLE OPERATION AT WENDOVER, UTAH For more than 25 years Bonneville, Ltd., now a division of Standard Magnesium and Chemical Co. (recently acquired by Kaiser Aluminum and Chemical Corp.), has been recovering potassium chloride from the brines found in the desert area just east of Wendover, Utah. Solar evaporation of the brines is possible as a consequence of relatively low precipitations (year average: 4.8 in.), and of dry and hot summer months. The brine, collected by a series of approximately 67 mi. of ditches crossing the desert, is fed into solar evaporation ponds. Evaporation which takes place from around the middle of May to about the end of September, permits the crystallization of approximately 90% of the originally present NaCl on what is called the "General Pond Area". Further evaporation,

Jan 1, 1964

By E. S. Machlin

The kinetics of vacuum distillation, vacuum-melt surface reactions, crucible-melt surface reactions and boiling are analytically investigated. No disagreement with experiment is obtained upon applying a rigid flow model to describe the behavior of the melt in the vicinity of reaction surfaces. The theory focuses attention upon measureable parameters rather than upon the adjustable parameter, stagnant layer thickness, associated with other theories. The rigid flow theory is thus capable of quantitative evaluation and experiments to achieve this evaluation are suggested. KINETICS, rather than thermodynamics, often determine the degree of refinement achieved in vacuum melting. There is little understanding, however, of the kinetic principles involved in vacuum refining. This paper represents an attempt to achieve this understanding. There are two reactions which need to be con- sidered. The first is the refining reaction. The second shall be called the polluting reaction. It is the reaction associated with the introduction of components of the crucible into the melt. The mechanisms of both reactions are unknown. Many models can be constructed to describe either the refining or polluting reactions. For example, consider the refining reaction C + Q = CO(g). One model that can be imagined is that the carbon and oxygen combine in the melt to form CO which then diffuses to a melt-

Jan 1, 1961

By E. P. Shoub, J. P. Riott, R. C. Buehl

Pilot-plant tests have demonstrated that it is possible to produce low-sulphur sponge iron (0.03 to 0.0; per cent sulphur) as a continuous process in an internally fired rotary kiln from iron ore or mill scale; a solid carbonaceous reducing agent; and dolomite to control the sulphur content. The proportion of dolomite employed is small, so that it does not add materially to the cost of the sponge iron. The entire operation is carried out at temperatures well below the melting point of iron, so that the product is discharged in granular form. Compared with other methods for the production of sponge iron, the rotary-kiln method has the advantage of simplicity and low cost of equipment and, in addition, requires little labor for the operation of the process. The pilot-plant equipment used for this work was sufficiently large to demonstrate that the production of low-sulphur sponge iron in rotary kilns is feasible and that the costs are not excessive for applications in which sponge iron has distinct advantages over competing materials. This report constitutes a part of a program by the Bureau of Mines under a special Congressional appropriation for studying gaseous and solid fuel reduction of iron ores. Numerous articles on various phases of these investigations have appeared in Bureau of Mines publications or technical journals. Other articles are being prepared and will be published in the near future. The present program, which is under the supervision of Dr. R. S. Dean, Assistant Director of the Bureau of Mines, was initiated in 1942. However, a considerable portion of the work was a continuation of previous research performed by the Bureau. Previous investigators1-4 utilizing the rotary kiln for the production of sponge iron did not develop a suitable method for controlling the sulphur content. A review of the literature shows that the sulphur content in the product usually exceeded 0.1 per cent unless reducing agents with very low sulphur contents were employed. This high sulphur value made the product generally undesirable for use as melting stock in electric or open-hearth furnaces. The production of sponge iron in an internally fired rotary kiln has been described in detail in Bureau of Mines Bullelin 2702; consequently, this article will be confined mostly to new features of the process—that is, means for controlling the sulphur content of the sponge iron. Suitable raw materials include iron ores or mill scale; coal or coke for reducing them, and sized dolomite ( — poi-100-mesh) as the sulphur-controlling agent. A mixture of the raw materials in granular form is fed into the elevated end of the kiln, which is fired axially from the lower or discharge end. In the reducing zone, which is approximately one third the length of the kiln measured from the dis-

Jan 1, 1948

By R. C. Buehl, J. P. Riott, E. P. Shoub

Pilot-plant tests have demonstrated that it is possible to produce low-sulphur sponge iron (0.03 to 0.0; per cent sulphur) as a continuous process in an internally fired rotary kiln from iron ore or mill scale; a solid carbonaceous reducing agent; and dolomite to control the sulphur content. The proportion of dolomite employed is small, so that it does not add materially to the cost of the sponge iron. The entire operation is carried out at temperatures well below the melting point of iron, so that the product is discharged in granular form. Compared with other methods for the production of sponge iron, the rotary-kiln method has the advantage of simplicity and low cost of equipment and, in addition, requires little labor for the operation of the process. The pilot-plant equipment used for this work was sufficiently large to demonstrate that the production of low-sulphur sponge iron in rotary kilns is feasible and that the costs are not excessive for applications in which sponge iron has distinct advantages over competing materials. This report constitutes a part of a program by the Bureau of Mines under a special Congressional appropriation for studying gaseous and solid fuel reduction of iron ores. Numerous articles on various phases of these investigations have appeared in Bureau of Mines publications or technical journals. Other articles are being prepared and will be published in the near future. The present program, which is under the supervision of Dr. R. S. Dean, Assistant Director of the Bureau of Mines, was initiated in 1942. However, a considerable portion of the work was a continuation of previous research performed by the Bureau. Previous investigators1-4 utilizing the rotary kiln for the production of sponge iron did not develop a suitable method for controlling the sulphur content. A review of the literature shows that the sulphur content in the product usually exceeded 0.1 per cent unless reducing agents with very low sulphur contents were employed. This high sulphur value made the product generally undesirable for use as melting stock in electric or open-hearth furnaces. The production of sponge iron in an internally fired rotary kiln has been described in detail in Bureau of Mines Bullelin 2702; consequently, this article will be confined mostly to new features of the process—that is, means for controlling the sulphur content of the sponge iron. Suitable raw materials include iron ores or mill scale; coal or coke for reducing them, and sized dolomite ( — poi-100-mesh) as the sulphur-controlling agent. A mixture of the raw materials in granular form is fed into the elevated end of the kiln, which is fired axially from the lower or discharge end. In the reducing zone, which is approximately one third the length of the kiln measured from the dis-

Jan 1, 1948

By Oscar Johnson

WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel's Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill.

Jan 6, 1954

Organization Place Date 1917 American Society of Sanitary Engineers Grand Rapids, Mich. Aug. 1-3 National Association of Stationary Engineers... Evansville, Ind. Sept. 10-15 National Safety Council New York City. Sept. 10-15 National Exposition of Safety and Sanitation. New York City Sept. 10-15 American Iron, Steel & Electrical Engineers..:. Philadelphia, Pa. Sept. 10-14 American Institute of Metals Boston, Mass. Sept. 24-29 American Foundrymen's Association Boston, Mass. Sept. 24-29 Chemical Industries, Third National Exhibition. New York City Sept. 24-29

Jan 8, 1917

By E. Seidl

THE basic material for testing aluminum, copper and zinc is a cast metal, principally in the form of wire bars (Figs. 1 to 3) and plates for the produc- tion of sheets or strips, (Figs. 4 to 7). Experience has proved that the chemical and crystallographic proper-ties of such cast metal exercise a certain influence when it is being worked, which is usually done while the metal is hot. In a chemical sense the slight impurities, which even the purest industrial metal contains, have a disturbing effect. They settle either along the outside limits of granulation, as in the case of aluminum and copper, or else in the interior of the crystal, as in the case of zinc; but frequently are also found accumulating at certain points (formation of the blowholes and skin) (Fig. 7). The crystallographic character of the metals is either that of uniformly fine granulation, or else there occurs a certain distinct casting texture marked by sharply defined cooling conditions and consisting of crys-tals of a pronounced stalk-like or blade form. Since we generally distinguish between a crystal texture and a crystal structure, the term crystal texture is used here for the arrangement of the crystals relative to each other and their microscopic composition; crystallic structure is used to mean the radioscopically ascertain-able structure of the crystal. The influence of the impurities and of the crystalline character on the working of the metals has been fre-quently pointed out in practice as well as in science.

Jan 11, 1927

By Henry J. Welge

Laboortory apparatus has been devised which permits study of the displacement of oil from cores by water and by gas. The cores used contained interstitial brine as well as oil. Experiments were run to determine the comparative effect of varying the properties of the fluids used. No great effect was noted on the maximum displacement achieved. This observation made it unnecessary in initial work to use fluids in their exact reservoir conditions. Consequently, the displacements were run at near-atmospheric pressure in Pyrex glass equipment, using stripped crude oils. Introduction and Theory The chief object of this work has been to determine the efficiency of gas and water as primary agents for displacing oil from reservoir rock under laboratory conditions in which capillary phenomena were predominant. To this end the maximum displacement of oil from cores has been ascertained. This maximum displacement may not be equal to the maximum displacement from a reservoir; but it will be a close approxirnation to it sometimes, and other times the laboratory information will be useful in reservoir engineering predictions. It is] believed that the laboratory experimental maximum represents the upper limit for the reservoir recovery. The experiments were carried out by obtaining cores of interest from the reservoir, and filling the pores with interstitial brine and oil with the restored state tech- nique.1 Then the oil was displaced from the core as described later, either by brine from below, or by gas from above. The former type of displacement suggests analogy to production by water drive, but not to water flooding, for reasons discussed below. The latter type of displacement is believed to simulate production by gas cap displacement. The displacements were performed by what may be termed the capillary-pressure method. The cores are placed in capillary contact with an oil-wetted membrane which has very small pores (about I micron in diameter). Pores of this size will transmit oil but Prevent the Passage of gas or water, unless the Pressures used are higher than the capillary Pressures employed in this work. Accordingly, use of the membrane makes it possible to apply a capillary pressure differential between the displacing phase and the oil in the core. AS in the displacement of brine toward that condition of oil and water distribution existing originally in the reservoir,' it may not always be desirable to reduce the oil saturation in this experiment to an absolute minimum. With reservoirs having small productive closure, it is preferable to evaluate and use a displacing pressure no higher than the capillary pressure, Ap, which will ultimately become available for displacement in the reservoir. This pressure may be calculated from a knowledge of the density of the oil-in-place, do, the density of the displacing phase, dl, and Ah, the vertical distance between the section of the

Jan 1, 1949

By Alan Morris

Season cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes arc fairly well understood and means for its prevention are inexpensive and effective, so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,' in discussing a paper by Hatfield and Thirkell, says: " He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultaneous corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack. Dr. McAdam3 has investigated the effect of corrosion on the fatigue limit of brasses, among other materials. He directed a stream of either fresh or salt water against the specimen while it was undergoing fatigue test. The corrosion-fatigue limits thus determined may be considerably lower than the endurance limit without coincident corrosion. The exact

Jan 1, 1930

By C. W. Sherman, J. Chipman, H. I. Elvander

THE pronounced and usually deleterious effects of sulphur on all ferrous metals and the resultant necessity for its control in metallurgical processes have stimulated many investigations of the system iron-sulphur. The data required for thermodynamic study of the behavior of sulphur in molten iron and steel include the activity and free energy of the dissolved sulphur and its heat of solution. Such data are also of theoretical interest since there is all too little information available concerning solutions of nonmetallic solutes in metallic solvents. It was the purpose of this investigation to attack the problem very directly by a study of equilibrium at several temperatures in the reaction H2 (gas) + S = H2S (gas) [1] K1 = PH2S /PH2 as where the sulphur is present in the liquid iron in amounts up to several percent by weight. Such a method of attack is not new since several careful studies have already been reported. It is planned, however, to extend the study to other metallic solvents and particularly to determine the effects of the various alloying elements on the activity of sulphur in liquid iron. This paper presents the results on molten iron-sulphur alloys containing up to 4 pct sulphur in the temperature range 1530°-1730°C. Literature Review The significant researches on dilute molten solutions of sulphur in iron include those of Chipman

Jan 1, 1951

By Fred C. Bond

It sometimes happens that old knowledge is forgotten, or half-forgotten, and its rediscovery is hailed as a great new advance in technology. Autogenous grinding affords such an example. The oldest-or apparently the oldest-commercial application of continuous autogenous grinding on a large scale outside of South Africa occurred at San Juancito, Honduras, where a total of more than two million tons of silver ore were ground autogenously with complete success from 1918 to the early 1940's. The history of the San Juancito silver deposits begins in 1880 when- the New York and Honduras Rosario Mining Co. started mining silver at a rate which soon reached two million ounces of silver annually. In 1912 the Company's first mill, located in the village of San Juancito, was shut down and its equipment transferred to a new cyanide plant. This plant, constructed on a mountainside near the mine, was equipped with tube pebble mills in which Normandy or Danish pebbles were used initially.

Jan 5, 1963

By R. S. Dean

THE numerous theories of hardening which have been advanced in recent years are all satisfactory in accounting for some of the phenomena observed in hardening metals, but none so far presented account for all of the facts observed. Some years ago one of the authors, R. S. Dean,1 presented a theory to account for some of the properties accompanying work hardening. The present paper develops this theory further in the light of recent experimental, work and extends it to other forms of hardening. Many of the ideas included have come from the writings and personally communicated thoughts of others. We have attempted to give proper credit in every case, but it is possible that we have not always done so. As an historical basis it is desirable here to review very briefly the hardening theories which have been current. The first comprehensive theory of work-hardening phenomena was due to Sir George Beilby.2 He contributed the idea that with cold work part of the structure of the metal was rendered amorphous and that it was to this amorphous material that the cold-worked metal owed its difference in properties. According to Beilby's theory this amorphous material was a super-cooled liquid and, therefore, had the characteristics of a vitreous material. That such a theory is not capable of explaining the property changes in metals has been repeatedly pointed out. This theory also allowed a slip to take place only once on a given plane, which, as has been pointed out by Jeffries and Archer,3 is not consistent with the observed length of an individual slip and the amount of elongation which can be obtained by wire drawing. The modifications, which have been proposed to this hypothesis to make it coincide with the experimental facts, have to a considerable extent robbed the theory of its clean-cut characteristics. The commonest of these modifications replaces the amorphous phase with an

Jan 1, 1927

By H. F. Silver

Although the literature indicated that a hydrogen-ated coal bitumen might be used as a substitute for petroleum asphalt and road tar, no work could be found in which the material was actually used or evaluated as a road binder.' Therefore, a study was initiated to investigate the production and properties of a road binder made by hydrogenating coal in the presence of a solvent at elevated temperatures and pressures. HYDROGENATlON PROCEDURE Four different samples of sub-bituminous Wyoming coals and three samples of coals from other states, ranking from lignite to a low-volatile bituminous coal,

Jan 1, 1969

By David J. Mack, Chin Bea Kim

The decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was studied by isothermal transformation. Its progress was followed by metallographic, hardness, and X-ray diffraction methods. Three transformation products were found: lamellar pearlite at high temperatures; an intermediate temperature structure; and martensite at the lower temperaCures. No transition structu,ves were found. THE decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was stuadied as part of a long-range program of study on the eutectoid transformation in alloy systems which do not have one or more components which exhibit allotropy. Available information on the Ni-Zn eutectoid transformation is limited to that presented in connection with the determination of the phase dilagram. No systematic studies of the eutectoid were found in the literature, alkhough the microstructures of the Ni-Zn eutectoid were reported by Tamuru.3 X-ray diffraction data exist for the ß, ß1, y , and y1 phases.' EXPERIMENTAL PROCEDURE The eutectoid alloy was prepared from "A" nickel shot and Bunker Hill super-purity zinc (99.998 pct).

Jan 1, 1962

By Edgar Bain

IN STUDYING the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900° C. (1650°, F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement-the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1. shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 2, 1924

By William Fink

NICKEL is used as an alloying element in several complex commercial aluminum alloys, among which are found some very interesting proper-ties, such as relatively high strength at elevated temperatures, relatively low coefficient of expansion, the absence of permanent growth, ability to take a good polish, and a bright, pleasing as-cast surface. For that reason the aluminum-nickel system was included in the list of binary aluminum systems that are being studied as a preparation for the investigation of more complex commercial alloys. This paper is the fifteenth of a series from the Research Laboratories of the Aluminum Company of America reporting the results of investiga-tions of equilibrium relations in aluminum-base alloys of high purity. The aluminum-nickel equilibrium diagram from 0 to 18 per cent nickel was determined, using the purest material available.

Jan 1, 1934

By Donald H. McLaughlin

THE primary function of the mining engineer is to find mineral deposits and fuels in the accessible rocks of the earth and to recover them for the vast needs of our complicated civilization. On him has been placed the responsibility for the exploitation of the nation's and world's mineral resources. The degree to which the minerals of the earth have been utilized serves to an extent as a measure of man's material advancement, as well as an index of the relative strength of nations. The natural endowment of lands, varies greatly, but the intellectual energy of a people is revealed by the way in which they take advantage of their heritage of minerals or reach out to less developed regions by exporting their engineering skill as well as capital to secure the raw materials they need.

Jan 2, 1953