Search Documents

By David B. Brooks

Identified potential resources of lead and zinc are lower, relative to reserves, than the same ratio for other metals, Either there is little material below present grades or, if it exists, there are no data on it. The author examines both these factors in detail, and also introduces a third possibility. In their 1961 monograph, The Future Supply of the Major Metals, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.' Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vast quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.'12 This situation, which they called "the lead-zinc anomaly'' has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative. There are at least two reasons for devoting time to the lead-zinc anomaly. First, while it is unlikely that we shall have to turn to alternative lead or zinc resources in the near or middle-term future, the longer run resource picture for the two metals is not so certain.3 Both within the United States and for the world as a whole, new discoveries will have to come at a fair pace to keep up with growing rates of consumption. Thus, it is important to see whether there exist lower grade or nonconventional potential sources of two such useful metals that we could turn to at some time in the future. The second reason for studying the lead-zinc anomaly is also related to resource adequacy, but is of more general significance. Depending upon whether the anomaly is technologic, geochemical, spatial, or temporal in origin, we shall be able to draw some conclusions about the resource picture for other metals. Can we expect the apparent pattern of lead-zinc resources to be repeated? If so, will technologic advances in either exploration methods or mineral processing be able to alter the pattern? Or is the pattern unalterably set by geochemical distribution? Most important, are metals characterized by what seems to be an anomaly, different in any way from metals for which low-grade or nonconventional sources already have come to be exploited, as the porphyry deposits have for copper. In sum, investigation of the lead-zinc anomaly represents a case study combining both physical and economic aspects that may open up a neglected area in evaluating mineral resource adequacy. WHAT IS THE LEALLZINC ANOMALY? There are two dimensions to evaluations of the potential of any mineral resource? The first involves the degree of certainty that we ascribe to the estimate: how much do we know about the size of the resource as a result of geological mapping, exploration, and mine development? This dimension is expressed by the terms measured, indicated, and inferred reserves (and, if you wish, 'undiscovered reserves'), all of which terms carry with them the implication of exploitability under current cost-price conditions. The other dimension to evaluations of a mineral resource involves the economic limits of the estimate: how will the size of the resource vary with different (usually more favorable) cost-price conditions? (This economic dimension should be understood broadly to include all factors bearing on the cost-price relationship. In this sense it subsumes technology because any resource is exploitable at some cost; the role of technology is to bring cost down.) The latter dimension is expressed in the terms potential or sub-marginal 'ore,' and is logically quite independent of the former. For example, we have relatively good measurements of the tonnage of manganese in low-grade deposits in this country, though they are too lean to be considered reserves; on the other hand, we are much less certain of our measurements of new lead and zinc deposits in Missouri, though there is no question but that there is a sizable reserve. Thus, it may be uncommon but is not a contradiction to talk of measured submarginal ore or inferred potential ore.

Jan 1, 1968

By N. J. Grant, R. Nordheim

An extensive study was made of the aging characteristics of alloys based on the 80 pct Ni-20 pct Cr composition hardened with aluminum and/or titanium, each up to 4 pct. Aging was followed by means of hardness and hot electrical resistance measurements as well as by X-ray and microscopy. Stress rupture tests at 1500°F were utilized as a check on the predicted behavior. THE titanium and aluminum hardened Ni-Cr alloys, exemplified by Nimonic 80 and Inconel X, constitute one of the more important groups of alloys developed to meet the demand for materials retaining their strength at elevated temperatures. For service in the temperature range 1200" to 1500°F, these alloys offer high creep resistance. With increasing service temperature, however, the strength of the simpler Ni-Cr base alloys falls off rapidly so that above 1500°F there is a significant loss of strength. The present investigation was undertaken with the hope that a better understanding of the factors controlling the precipitation hardening of these alloys would make it possible to increase the useful service temperature range. Primarily this investigation involved the study of the effects of titanium and aluminum on the hardening and the subsequent softening at elevated temperatures. The titanium and aluminum contents were each varied between 0 and 4 pct by weight at a constant nickel to chromium weight ratio of about 4:1. (Except when otherwise stated, all compositions are expressed on a weight basis.) The major part of the investigation was confined to alloys with less than 0.06 pct C. Recently several papers dealing with the identity of the microconstituents in the titanium and aluminum hardened Ni-Cr alloys have been published. Using X-ray analysis of the residues from anodic dissolution, Rosenbauml was only able to identify carbides and nitrides in Nimonic 80 and Inconel X. However, since Rosenbaum worked with alloys in the hot rolled rather than in the aged condition, his results are inconclusive. Recently Hignett' reported that the hardening of Nimonic 80 was due to the controlled precipitation of Ni,(TiAl) having the cubic Ni3A1 structure. Taylor and Floydv-" published the results of an investigation of the nickel-rich corner of the Ni-Cr-Ti, Ni-Cr-Al, and Ni-Ti-A1 systems. In the Ni-Ti and the Ni-A1 systems the hexagonal Ni,Ti phase, 7, and the cubic Ni3A1 phase, -y', respectively, exist in equilibrium with the nickel-rich solid solution. The interatomic distances in the basal plane of Ni,Ti and the octahedral planes of the matrix are almost equal, thus explaining the Wid-manstaetten type structure formed when Ni,Ti precipitates from solid solution. When Ni:,Al precipitates from solid solution, it appears usually in globular form, often dispersed along rows corresponding to definite crystallographic directions. The 7 and phases are also the only intermetallic compounds which occur in the nickel ternary alloys with up to 25 pct Cr and 10 pct Ti or Al. Taylor and Floyd found that Ni,Ti takes practically no nickel, chromium, or aluminum into solution. Nial, on the other hand, dissolves a considerable amount of chromium and titanium and some nickel. Up to three out of every five aluminum atoms could be replaced by titanium in Ni,Al. This substitution caused a slight increase (less than 1 pct) in the lattice parameter. With respect to the effect of variation in the titanium and aluminum contents on the high temperature strength of Nimonic 80 type alloys, Pfeil, Allen, and Conway" reported that an 80 pct Ni-20 pct Cr alloy containing 0.20 to 0.30 pct A1 had the highest creep resistance when the titanium content was kept between 1.65 and 2.75 pct. Experimental Procedure The materials used for this investigation were electrolytic nickel, electrolytic or low carbon chromium, sponge titanium and 2s aluminum. The alloys were melted in an indirect carbon arc furnace under

Jan 1, 1955

By G. H. F. Gardner

The velocity and attenuation of elastic waves in sandstones were measured as a function of both pressure and fluid saturation. A large change occurs in these quantities if water is added and the rock is not compressed, but the change is small if the rock is subjected to a large overburden pressure. Measurements were made by vibrating cylindrical samples in both the extensional and torsional modes at frequencies up to 30,000 cycles/sec. Formulas were derived which enable the attenuation of dilatational waves in dry rocks to be deduced from the data. Similar experimental methods were used to investigate the properties of unconsolidated sands. Velocities were found to vary with the 1/4 power of the overburden pressure and attenuations to decrease with the 1/6 power. The effects of grain size, amplitude and fluid saturation were studied. Formulas by which the effects produced by a jacket around the sample may be calculated were derived. The practical application of these results to formation valuation is discussed. INTRODUCTION The attenuation of elastic waves in the earth has been of interest to the seismologist and geophysicist for many years, but only recently to the petroleum engineer. Engineering interest has been brought about by the success of velocity logging devices, for it is possible by modification of these instruments to measure the attenuation of sound waves in addition to their velocity and, hence, deduce the mobility of formation fluids as well as the porosities of the rocks which contain them. The main problem is to decide whether field measurements can be made with sufficient accuracy to be of practical use. This problem can only be solved after we know the magnitude of the attenuations which are typical of the earth at various depths. The logarithmic decrement of a fluid-saturated rock is the sum of a "sloshing" decrement and a "jostling" decrement, the former caused by the mobility of the fluid contained within the rock and the latter by the granular framework of the rock. Sloshing decrements can be calculated' using Biot's theory, but the jostling losses are less well understood. The present paper reports an experimental investigation of jostling losses in consolidated and uncon- solidated sands, particularly with respect to the effect of overburden pressure and fluid saturation. Born' showed that the decrement of a sandstone may increase dramatically when only a few per cent by weight of distilled water is added, and that the additional loss is proportional to the frequency of vibration. His measurements were made with no compressive stress on the framework of the rock. M. Gondouin3 investigated similar phenomena for fluid-saturated plasters but also did not compress the samples. In the present paper it is shown that compression of the framework reduces this effect, so that at depth the jostling decrement of a sandstone may be expected to be almost independent of fluid saturation and frequency. Decrements for many sedimentary rocks have been given by Volarovich,4 but all for the state of zero overburden pressure. Anomalously low velocities have been logged in shallow unconsolidated gas sands. Results of the present investigation confirm that these velocities are not caused by correspondingly high attenuations, because the jostling decrement in a packing of sand grains is small and much less than in a consolidated sandstone at the same depth. Velocities in sands have been measured by Tsareva5 and by Hardin6 as a function of pressure, but the corresponding decrements do not appear to have been measured previously. The widely used "resonant bar method" of measuring velocities and decrements was employed. Comments on variations of this technique have recently been published by McSkimmin.7 The main novelty of the present technique was the application of pressure to the samples. It was found possible to do this by placing the apparatus inside a pressure vessel, provided the conditions leading to large additional losses were avoided. These conditions are discussed below. EXPERIMENTAL TECHNIQUE Cylindrical samples were caused to vibrate in both the extensional and torsional mode of vibration and the amplitude of vibration was measured as a function of frequency in the neighborhood of a resonant frequency. The resonant frequency, fr, is related to the corresponding elastic modulus by the formulas where E and N are Young's modulus and the modulus of rigidity, p is the density of the sample, and A the wavelength of the vibration.

Jan 1, 1965

Alfred C. Young† (communication to the Secretary): Before the appearance of Mr. Scott's paper in these Transactions we were not specially interested in the investigation which he has started; but at his request we have endeavored to collect from musty records and the recollection of our old friends a brief chronicle of the progress made by this house. As 3000 instruments were manufactured by us before any descriptive record was kept, and 2000 more before the record contained more than a statement whether the instrument was a transit or a level, and sometimes its size, we approach the task with timidity, trusting that the reader will bear the difficulties in mind, particularly as the writer's predecessors, from whom, no doubt, the information desired could have been obtained, have passed away. Instruments for surveying were manufactured by David Rittenhouse, of Philadelphia, as early as 1760; but it was not until late in the first quarter of this century that there was any American market for an instrument outside of the ordinary surveyor's compass. With the advent of canals and railroads, and the more extensive development of the Pennsylvania coalfields, arose a demand for surveying-instruments to meet problems in engineering beyond the limited field of the compass. On May 1, 1820, in which year the practical mining of anthracite coal in Pennsylvania began, William J. Young, who had served his apprenticeship with one Thomas Whitney,

Jan 1, 1901

By J. Weertman

It is shown that conditions suitable for the conversion of straight dislocations into helices are common in crystals hardened either through long-range dislocation interaction or by jog formation on dislocation lines. For dislocations other than screw dislocations or dislocations nearly screw in orientation, helices can be formed with the aid of core difhsion at temperatures low relative to the melting point of the material. It is assumed that, once formed, helices will degenerate into dislocation tangles. THE dislocation tangle is one major dislocation arrangement observed by the transmission electron microscope which had not been predicted previously from dislocation theory. Since first being observed, the tangle itself has become important in applied dislocation theory. The Cambridge school (P. Hirsch) bases part of its theory of work hardening upon this phenomenon.' In spite of the fact that the tangle obviously is a structure of prime importance to a cold-worked crystal, until recently relatively little attention has been paid to the question of exactly why or how tangles arise. It was generally assumed at first that cross slip and perhaps jog formation will lead to tangles. However Wilsdorf and schmitz2 concluded that cross slip cannot markedly contribute to the tangles. The Wilsdorfs and Maddin3'* have proposed that tangles arise by means of prismatic dislocation loops and superjogs which are produced by a precipitation of point defects. Dislocations with superjogs or which have joined with prismatic loops are themselves dislocation sources and they can produce new dislocations, a process they call "mushrooming", which then tangle with each other. There is no question that the Wilsdorfs et al. mechanism as well as the cross slip one can pro- duce tangles. However these may not be the only paths leading to tangle formation. In this paper we wish to consider another way tangles can form. Our work will be based on the theory of dislocation screw We wish to show that whenever a crystal is cold-worked there always is present a "driving force" leading to helix formation and thus to tangle formation. We do not expect to observe well-developed, regular helices in cold-worked metals. Rather we would expect that after a helix is formed random interactions with nearby dislocations will cause a well-developed helical dislocation to go over into an irregular form. A dislocation tangle is, of course, a grouping of dislocations with irregular forms. Therefore we feel that, in accounting for the formation of dislocation tangles, it is sufficient to show that many dislocations in a cold-worked crystal will take on helical form. The crucial step is helix formation. In order to have a straight dislocation assume a helical form, diffusion of vacancies, or interstitials, must occur. Our discussion of tangle formation therefore will be limited to crystals which have been deformed at temperatures ranging from about one fifth to half their absolute melting point. In this tem per a ture range appreciable core diffusion is possible. (There is no problem in explaining tangle formation at temperatures greater than half the melting point. At such temperatures dislocation climb through a bulk diffusion of point defects gives an extra degree of freedom to dislocation motion. This extra freedom of motion makes tangle formation easy.) At temperatures much below one fifth the absolute melting temperature diffusion processes are sufficiently slow that helix formation does not occur. Of course helix or tangle formation could occur in material deformed at very low tempera-tures which was subsequently warmed in order to make the thin specimen necessary for electron-microscope examination. Since within the temperature range of approximately one fifth to half the melting temperature the diffusion of point defects in the core of the dislocation is rapid, we can reasonably assume that within

Jan 1, 1963

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By Ossi V. I. Hintikka, Andrew Balint

Sorting tests on limestone at the Lohjan Kalkkitehdas Oy Ojamo mine, Finland, are described. The tests, conducted to evaluate a Sortex 811MW optical separator, were successful, and upon completion, the sorting machine was put into production. Optical separation characteristics of the limestone, used for cement manufacturing, are described. Problems of winter operation are discussed. Operating costs are given.

Jan 1, 1972

By D. F. Stoneburner, G. Derge, Ling Yang

PREVIOUS investigations in this laboratory have shown the existence of electronic conduction in several molten metal sulfides and the specific conductance of a number of these has been measured as a function of temperature.' In order to better understand the electronic nature of these melts, the thermoelectric power of a molten FeS-solid tungsten thermocouple was measured and a value of approximately 55 µv per "C was obtained in the temperature range from 1200" to 1400c2 These studies have been continued and the thermoelectric power of several other molten metal sulfide-solid tungsten thermocouples have been obtained. The experimental arrangement is shown in Fig. 1. A Kanthal furnace was used, doubly wound to prevent any undesirable effects of an external field. A 1/2-in. McDanel tube was fitted with two vertical 5/8-in. McDanel tubes as shown. These tubes were about 2 in. apart. A graphite boat was used to hold a re-crystallized alumina boat in which the prefused sulfide was placed. Two probes were made using

Jan 1, 1960

By Stuart McGill

This case-study of the financing of the Ok Tedi project illustrates the nature of project financing and outlines the arrangements made in the case of this project; it also demonstrates that the limitation of financial exposure is an important goal for Governments involved in developing the resources sector. The account includes a chronological description of the process by which the sponsors prepared for the financing of the project and the lenders became involved in it. The type of security arid loan documentation required for such financing is described, together with a broad analysis of their content and the manner in which the various risks involved in development are apportioned among the sponsors and lenders. The ability to apportion and limit financial liability is an important development for the owners of capital and resources.

Jan 1, 1985

By R. F. Mehl, G. T. Horne

Diffusion coefficients and mobilities were determined as functions of concentration in the a phase of the Cu-Zn system. Use was mode of incremental diffusion couples to determine the Kirkendall effect at various concentrations. Darken's analysis was used to calculate the individual diffusion coefficients and mobilities from these data. The general diffusion coefficient is a single-valued function of the concentration in this system to within the limits of accuracy of the experimental methods used. The form of the various functions (diffusion coefficients and mobilities) of concentration is the same in every case: it is essentially the same as the usual D vs c curve. AS Darken' has pointed out, the knowledge that the movements of different atoms diffusing in the same lattice need not proceed at the same rate is old. Ionic lattices are the classical examples; application of the generalization to lattices with metallic bonding was much more slowly accepted. It remained for Kirkendall'' to show clearly that metallic diffusion need not be symmetrical with respect to both species. Several investigators" have confirmed the initial observation of a "Kirkendall effect:" marker movement accompanying diffusion. They have extended it to other systems and conditions. The theoretical interpretations have been many; ne of the first and simplest of these is that of Darken"' which is essentially mechanism independent. Darken has shown that the Kirkendall experiment permlts a calculation of the individual diffusion coefficients and, coupled with activity data, offers a means of measuring the mobilities of the separateatoms in a binary diffusion process. There is no published information on the effects of concentration and temperature on the individual diffusion coefficients or on the mobility values in binary solid solution; this paper provides such information for zinc and copper in a brass. For purposes of clarity, the overall D value obtained, for example, from the Boltzmann-Matano solution to Fick's law, will be designated as the "general diffusion coefficient;" and the diffusion co- efficients for the separate diffusing species will be designated as the "individual diffusion coefficients." Experimental Procedure The authors have accepted Darken's analysis and have measured mobilities on this basis. The findings of da Silva and Mehl are accepted: that the Matano interface, defined as the origin of coordinates for the Boltzmann-Matano solution to Fick's law, coincides with the original weld interface; that the "shift" of a marker is the distance between the Matano interface and the marker; that the observed porosity is too small sensibly to affect this result; and that the shift is a linear function of the Matano area, the area defined as the absolute magnitude of the area on either side of the Matano interface. Alloys: The a-phase of the Cu-Zn system was chosen for investigation. The measurements were made on incremental couples for two separate reasons: l—it has been questioned whether D, the general diffusion coefficient, is a single-valued function of concentration (a comparison of the D-values for couples with small concentration range, e.g., 10 vs 20 pct Zn, against those from a wide concentration range, e.g., 0 vs 30 pct Zn, will answer that question); and 2—on the Darken analysis, the mobility can be determined only at the concentration at which the marker is observed to lie (this is but one concentration in a single couple) but choosing a series of incremental couples in the range between 0 and 30 pct Zn provides mobility values at several concentrations, thus giving mobility as a function of concentration. Four alloys were chosen; nominally, pure copper, copper with 10 pct Zn, copper with 20 pct Zn, and copper with 30 pct Zn. This allowed six different types of diffusion couples to be prepared, promising mobility determinations at six different concentrations, but having a minimum range of 10 pct Zn. The copper was an especially prepared pure copper supplied through the courtesy of the Ameri-

Jan 1, 1956

By Lewis A. Smith

Chromium is one of the new metals, but considerable research has been required to determine an approximate record of its production from 1827 until the present. Its use in the form of pure metal is not extensive; of the chromite mined, about one-half is required for making ferrochro-mium, about two-fifths goes directly into refractories and the remainder is absorbed chiefly by the chemical trades. The industries that demand chromite for such uses are mainly in countries that produce little chromite, while the important chromite-producing countries are not generally consumers. The international flow of chromite is therefore of interest, as well as the political and commercial control of resources of the metal. World Production The first mining of chromite is said to have occurred as early as 1820, at the Roros deposit in Norway, but the first well-established output came from the Reed mine, in Maryland, about 1827. Thereafter the United States led the world in chromite production until 1860, when Turkey took the lead. Russia in turn became the chief producer from 1897 to 1902, inclusive. From 1903 to 1909, New Caledonia held first place, but alternated with Southern Rhodesia from 1910 to 1917, inclusive. In 1918, 1919 and 1920-1921, the United States, India and New Caledonia led, respectively. In 1922 Southern Rhodesia assumed first place and has since continued to be the world's foremost producer by a large margin. Fig. 1 illustrates the production of the leading countries from 1890 to 1929, inclusive. Fig. 2 shows the world production of chromite from 1890 to 1929, inclusive, in long tons and Table 2 gives the production by countries for the same period. The total world production for the 103 years, 1827 to 1929, ipclusive, is estimated at about 7,100,000 long tons, distributed as shown in Table 1. World Trade in 1928 In reviewing the figures for the flow of chromite in 1928, it is evident that the six countries that produce most consume little chromite and

Jan 1, 1931

By Dorsey Lyon

INTRODUCTION THE electric furnace has always been found to be especially adapted to melting, refining, and finishing processes throughout its gradual acceptance by metallurgists, as a practical apparatus for conducting metallurgical operations. In the steel industry, the electric furnace is firmly established in the manufacture of steel of the highest grade, equal to crucible steel. For the production of the cheaper grades of steel in large tonnage, the electric furnace gives a higher-grade product than the open-hearth or converter, but due to the high cost of power prevailing in steel centers, considered from the electric furnace standpoint, it is not economical to produce tonnage steel in the electric furnace. As a refining and finishing agent for open-hearth or Bessemer steel, the electric furnace has had some degree of success in the production of tonnage steel. After a study of the use of the electric furnace in the steel industry, it appears that there may be a possibility of its use to advantage for the melting of cathode copper. In the case of copper the problem is not one of actual refining, because the copper if refined properly y the electrolytic method needs no further refining; it needs simply to be cast into a marketable shape. The name" refining". is applied to the present finishing process, because in the operation oxygen and other impurities are removed, which the electrolytic copper absorbs in being melted in the reverberatory furnace. Considering that processes may be positive, negative, and neutral; the electrolytic method would be positive; reverberatory melting of cathode copper, negative; and electric furnace melting, neutral. The electrolytic method produces about as pure a copper as is possible, if operated properly and the anodes are not too impure. The final reverberatory melting of this cathode copper lowers the grade of the final product, due to the absorption of gases and impurities.

Jan 8, 1914

Jan 1, 1938

By F. H. Kihlstedt

THE Larap iron deposits, 125 miles east of Manila, are the biggest high-grade iron deposits in the Philippines, and have in seven years produced nearly 4 million tons of 6o per cent ore. Magnetic surveying followed by churn and diamond drilling cheaply developed a score of million tons. The ore zone is a wedge of metamorphic rocks in fresh, Miocene sediments overlain by agglomerates, which seem to have filled a river valley eroded in the sediments. A mild overthrust of the competent agglomerates crumbled the shale in front. Solutions gradually turned it into more competent hornfels and deposited pyrite, then magnetite and pyrite in the pores. As the temperature rose large bodies of magnetite with some pyrite were deposited by replacement and in open cavities in tensional areas of overthrust shears. At still higher temperature magnetite and calcium-magnesium silicates formed other bodies in similar cavities, and finally the thrust zone was invaded by syenite porphyry, causing high-temperature alteration products. Possibly, as temperature abated, more high-grade ore was deposited. The complicated faulting indicates dynamic, chronological and spatial changes of mineralization rather than zoning in a static system. Noncommercial copper, molybdenum and some gold accompanied the iron mineralization. In the thirties the Philippines gained a justified reputation as a country of considerable mineral wealth. Traces of Chinese workings show that these earliest travelers and traders had in a small way exploited the latent gold resources in the Islands. The Spaniards continued this for centuries, but did not succeed in establishing any steady mining industry. Modern technology was required to get it started. The rapid development in the last decade before the war got its impetus from several financial factors, the return to sugar growers of previously collected taxes, the influx of Spanish capital during the civil war in [ ] Spain, the influx of Chinese capital when the Japanese started their "China incident," and others. Directly or indirectly much of this capital reached the mining industry; in particular, gold mining. Out of the turmoil of an exceptional mining boom emerged a sufficient number of good and well managed gold properties to send the production to a level above that of any single state in the United States at the time. Other ore deposits besides those of gold also received their share, and for a country without any heavy industries at

Jan 1, 1946

By V. Apraxine, J. Lakaye, J. J. Saquet, P. Troch

Union Minière du Haut-Katanga owns concessions for extracting copper and associated metals in the high plateau region of Katanga. The concession is about 188 miles long by 44 miles wide and has three principal areas: Southern area-The Prince Leopold mine is an underground operation from which a copper-zinc sulfide ore is extracted. The mine and associated concentrator are at Kipushi. Copper concentrates are smelted and converted to blister copper at the Lubumbashi smelter at Elizabethville.

Jan 12, 1962

By Michael J. Messel

The critical shortage of asbestos fiber in the world today brings to the foreground the question of locating and developing new deposits. The object of this paper is to discuss some of the more important factors which should be considered in the examination and valuation of a new asbestos enterprise. Some of the more important uses of asbestos fiber are for textiles, heat insulators, building materials, filters and a series of other uses. The properties of this mineral, such as fibrous structure, color, strength, silkiness and flexibility, coupled with resistance to fire, certain chemical action and decay make its application unique for certain industrial uses which consume over 500,000 tons annually. These same unique properties which make this mineral so valuable also make a deposit one of the most difficult to appraise accurately, because of the many undeterminable and varying factors which must be considered before a deposit can properly be termed commercial. The majority of the asbestos fiber today, having the above mentioned properties, is sold by grades which are based on fiber length. Present day fiber prices vary over a wide range from $800 to $225 for crude fibers and $300 to $20.00 per ton for milled grades. For valuation purposes a careful study should be made of existing fiber prices and markets. Examination of Deposits In carrying out prospecting and examination of a deposit, considerable caution is required to get the necessary information in the form that will have the most value for the final determination. There are two main classes of asbestos fibers, chrysotile and the amphiboles, the chrysotile being, by far, the most important both in abundance and uses. This paper will stress mainly chrysotile deposits, however, the amphiboles have many important uses, especially amosite and crocidalite. Their valuation presents special problems as other factors may be involved, especially as they are not graded according to any well defined and adopted standard but usually according to the use for which they are being supplied. Most chrysotile deposits occur in two main types of rock, (I) mainly in basic igneous, such as dunite and peridotite, (2) to a lesser extent in sedimentary rocks, such as dolomite and limestone. All of these require a certain degree of metamorphism to be favorable to asbestos formation. Approximately 90 pct of the asbestos deposits are derived from serpentinization of dunite or peridotite, whereby the magnesium-silicate olivine was altered to hydrous magnesium-silicate serpentine. Under certain favorable geological conditions, this serpentine takes a fibrous form having a definite crystal structure, probably due to molecular rearrangement, and is known as chrysotile. The fiber veins are usually ir-

Jan 1, 1948

By Michael J. Messel

The critical shortage of asbestos fiber in the world today brings to the foreground the question of locating and developing new deposits. The object of this paper is to discuss some of the more important factors which should be considered in the examination and valuation of a new asbestos enterprise. Some of the more important uses of asbestos fiber are for textiles, heat insulators, building materials, filters and a series of other uses. The properties of this mineral, such as fibrous structure, color, strength, silkiness and flexibility, coupled with resistance to fire, certain chemical action and decay make its application unique for certain industrial uses which consume over 500,000 tons annually. These same unique properties which make this mineral so valuable also make a deposit one of the most difficult to appraise accurately, because of the many undeterminable and varying factors which must be considered before a deposit can properly be termed commercial. The majority of the asbestos fiber today, having the above mentioned properties, is sold by grades which are based on fiber length. Present day fiber prices vary over a wide range from $800 to $225 for crude fibers and $300 to $20.00 per ton for milled grades. For valuation purposes a careful study should be made of existing fiber prices and markets. Examination of Deposits In carrying out prospecting and examination of a deposit, considerable caution is required to get the necessary information in the form that will have the most value for the final determination. There are two main classes of asbestos fibers, chrysotile and the amphiboles, the chrysotile being, by far, the most important both in abundance and uses. This paper will stress mainly chrysotile deposits, however, the amphiboles have many important uses, especially amosite and crocidalite. Their valuation presents special problems as other factors may be involved, especially as they are not graded according to any well defined and adopted standard but usually according to the use for which they are being supplied. Most chrysotile deposits occur in two main types of rock, (I) mainly in basic igneous, such as dunite and peridotite, (2) to a lesser extent in sedimentary rocks, such as dolomite and limestone. All of these require a certain degree of metamorphism to be favorable to asbestos formation. Approximately 90 pct of the asbestos deposits are derived from serpentinization of dunite or peridotite, whereby the magnesium-silicate olivine was altered to hydrous magnesium-silicate serpentine. Under certain favorable geological conditions, this serpentine takes a fibrous form having a definite crystal structure, probably due to molecular rearrangement, and is known as chrysotile. The fiber veins are usually ir-

Jan 1, 1948

By James P. Roe

Steel has occupied such a prominent position in most minds during the last thirty years, particularly since the introduction of the basic open-hearth process (by which the field from which the raw material could be obtained has been so widened), that little attention has been made to improvements in puddling iron. In fact, the general tendency seems to have been to accept the prediction that puddled iron is doomed. Events have in a measure justified such a forecast, due in large part to the introduction of mechanical appliances and operations with large units in the manufacture of steel, from which much lower costs have resulted. But this general tendency has met checks in certain directions. This is notably the case where the finished product is a welded one, or is subject to oxidation, to shock or to vibration; and, as far as the writer's observation goes, the bond (which is largely a mechanical one) is not as close and lasting between steel and tin or zinc as between iron and the same materials. The field still open for puddled iron is, therefore, a large one, provided the low costs of steel-manufacture can be approached. The process of puddling is one of the most interesting in the metallurgy of iron, as the reactions and the changes effected are apparent. The subject has had the strongest fascination to the writer from boyhood, and has led, not unnaturally, to a close study, which long ago resulted in the conviction that it could be successfully carried out with large units and by mechanical means. That others have also drawn these conclusions is shown by many undertakings, though there have been few such attempts during the last twenty-five or thirty years. Puddling cousists, essentially, in the removal of most of the carbon and silicon, and part of the phosphorus and sulphur

Jan 1, 1903

By R. F. Weber

The relation between the chemical composition and the refractoriness of fire-brick has long attracted the attention of manufacturers of fire-brick and others interested in their use, yet but little systematic work has been done along this line, especially in the United States. Analyses of fire-brick have been quoted for years, but fire-tests of brick, except those of durability in practical use, have usually been lacking. Although many tests and analyses of foreign fire-brick have been published, only a few have appeared in the United States; and even in the foreign literature, the references and facts are more or less scattered. The most elaborate foreign paper on the subject is that by Dr. Jochum.' One of the earliest, and perhaps the most detailed piece of work in the United States, is that of F. Platt, which was done for the Pennsylvania Geological Survey, in 1876.2 His investigation consisted of the analysis and heat-tests of 21 bricks, the testing being made in an experimental shaft-furnace at Har-risburg, Pa. All the bricks were more or less affected at the temperature reached, which was considerably higher than the melting-point of steel. The exact temperature at which individual bricks fused was not ascertained, hence the comparisons quoted in the paper are of value only for the bricks used in the test. The next comprehensive investigation, made by the New Jersey Geological Survey,³ deals chiefly with fire-clays; analyses and refractory tests having been made of 123 clays, kaolins, feldspars and fire-sands. Here; again, there was no accurate means of measuring the temperature, the only measurement of

Jan 1, 1905