Search Documents

By H. F. Bishop, F. A. Brandt, W. S. Pellini

The solidification mechanism of experimental steel ingots (7x7x20 in.) was studied by thermal analysis. It was determined that solidification proceeds in wave-like fashion at rates which are determined by the carbon level, superheat, and mold thickness. The thermal cycles of the mold walls were related to the course of solidification. ESPITE marked advances in the field of solid state transformation, metallurgical research has contributed comparatively little exact quantitative data on the mechanism of solidification of metals. There is, therefore, a great need for such data in the various metallurgical industries. The mechanics of solidification of ingots have been investigated in the past primarily by studies of the rate of skin formation as indicated by bleeding or "pour out" tests. The "pour out" method, however, is a tool which gives only approximate information. In the case of alloys with wide solidification ranges, such as irons and certain nonferrous alloys, the method will not work at all; in the case of alloys of intermediate solidification ranges, such as commercial steels, the information may be misleading. Thus, the general adoption of this method has resulted in divergent conclusions regarding the solidification process. Chipman and Fondersmith1 by means of bleeding tests have shown that the linear growth of a solidifying ingot wall follows a parabola of the general form, D = K C, with the start of solidification delayed until superheat is exhausted, as indicated by the constant C. These tests were carried only to a wall thickness of about 5 in. using an ingot of approximately 17x39 in. in cross-section; hence the latter stages of solidification were not studied. Matuschka2-3 indicated that linear solidification of ingots is rapid at first, then slow, but toward the end of solidification the rate becomes extremely rapid again. Spretnak's4 bleeding studies indicated that, wall growth is expressed more rigorously by two parabolas, and that their point of intersection corresponds to a change of solidification mode from columnar to equiaxed. Spretnak also showed that the K values of the first parabola are always the same regardless of superheat. Nelson bled ingots of square cross-section and found that linear wall growth is initially rapid but decreases continually until the end of solidification. He also concluded that rate of solidification in ingots of square cross-section increases 2.15 pct for every 10 pct increase in cross-sectional area of the mold. The mold ratios considered (ratio of cross-sectional area of the mold to cross-sectional area of the ingot) were all less than 2 to 1. The subject of solidification has also been treated mathematically in many cases, but because of the lack of accurate thermal constants and the simplifying assumptions required, as their authors generally acknowledge, they represent only approaches to the actual conditions of ingot solidification. A third method of studying solidification is the electrical analogue method promulgated by Pasch-kis6-7 and by Jackson and coworkers.8 This method treats solidification as a heat transfer problem with the solidification cycle synthesized on an electrical circuit. Paschkis in his treatment of solidification considered the fact, which was generally ignored, that solidification of steel is not simply the growth of a plane solid wall but a more complex process occurring over a temperature range as indicated by the constitution diagram. Undoubtedly, the anomalous results obtained by bleeding tests arise from the inability to measure quantitatively this mushy condition. The shape of Paschkis' solidification curves are more nearly in accord with those of Matuschka, in that they indicate rapid linear solidification at the beginning and end of solidification with intermediate solidification occurring at a slower rate. Paschkis indicates a definite lengthening of solidification time with increasing superheat. Thermal analysis is a direct method providing exact information for all types of metals regardless of solidification range and was thus adopted in the present program to follow the entire course of solidification from the surface to the centerline of the ingots. The method has the added advantage of being adaptable to following the thermal cycle of the ingot mold during the course of solidification. Test Methods The ingots studied were of square cross-section, 20 in. long, tapered from 71/4 in. at the top to 63/4 in. at the bottom, and fed with a hot top 7 in. in diam and 12 in. high. The molds were uniform in wall

Jan 1, 1953

By M. Muskat, H. G. Botset, R. D. Wycoff, M. W. Meres

The subject of the flow of homogeneous fluids—gases alone or gas-free liquids—through porous media may be considered at the present time to be fairly well completed. That is, analytical, graphical, numerical, or experimental methods are now available for obtaining detailed descriptions of the behavior of such homogeneous fluid systems of any reasonable geometry. Thus, satisfactory empirical techniques are now well established for the determination of the permeability of porous media for homogeneous fluids, the numerical magnitude of this permeability uniquely and completely describing a porous medium as a carrier of a homogeneous fluid. Considering this constant as known, the treatment of a wide variety of specific problems involving either the flow of gases or liquids has been carried through to satisfactory conclusions. Beginning with the simple case of strictly radial two-dimensional flow of a liquid or gas into a well under steady-state conditions, generalizations have been developed to apply for systems where the flow is not strictly radial, due either to a lack of uniformity in the reservoir pressures at points distant from the well or deviations from circularity of the external boundary whereby the fluid is being supplied, and finally, to the lack of complete penetration of the well into the producing strata. Satisfactory descriptions are now available for cases where gravity is acting as the driving agent inducing the flow of liquid into the well, either alone or as a supplement to the effect of pressure. The effect of acid treatment on limestone wells has been given a reasonable interpretation on the basis of the fundamental theory of the flow of homogeneous fluids through sands, as have the important features of the problem of water-coning. Then, too, systems in which the outlet of the fluid from the underground reservoir is of a predominantly multiple character may be now considered as in the domain of

Jan 1, 1937

Mr. Brown : .That part of the Standard Company's plant which has been added since the publication of Mr. Leggett's paper, and is described in mine, renders the single-phase, alternating system, which Mr. Hale has called " unelastic," much more elastic than it had been. The original plant at Bodie was substantially the same as the Telluride plant mentioned in his paper. The machines came from the same shops, and were practically the same; but while the Telluride Company has changed completely to a polyphase system, the Standard Company has retained its original plant, but has belted on a directcurrent generator at the receiving end, thereby converting the water-power into electricity, electricity into power, the power into electricity, and finally again electricity into power for use in the mines. This is a roundabout course, to be sure, but it shows that there are possibilities even in the out-of-date single-phase system. The only point perhaps, that deserves particular notice with respect to the hoist is the fact that the rheostat, or starting-resistance, was not built originally

Jan 1, 1897

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 114 to 112 in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles.

Jan 8, 1960

By Will Coghill

As the title indicates, this paper treats of the degree of liberation of minerals after grinding. To obtain the supporting data a "tool" not commonly used by metallurgists has been employed. It is the "heavy solution." The advantages gained through its use are shown. Actual ores were employed in order to make the study concrete. The selection was somewhat incidental and happened to embrace the red iron ores of Alabama. So, any reader interested in these ores will find some of their properties described. The red ores constituted the material examined and a somewhat new adaptation of heavy solutions was the tool of examination. If either the ores or the tool interest the reader these notes may be of some value. The writer's chief interest was in the rate of liberation of locked grains. Ores are generally ground preparatory to concentration and as long as the concentrators make suitable products the effectiveness of the grinding is likely to be unquestioned. But when suitable products are difficult to make, an investigation becomes imperative. In such a case a dissection of the ore might be made to find the cause of the trouble. Such a condition of unsuitable products exists in the low-grade red iron ores of Alabama. They are difficult to concentrate. To be sure it might be said that the concentration of iron ores is a new thing and that the ore-dressing methods are undeveloped, but a glance at the industry reveals an abundance of methods and devices for almost all imaginable conditions. Concentrating machinery has not taken a part in this investigation; the use of it would have been only machinery testing, and should never precede the ore testing which consists of such methods as herein outlined. When the properties of the ores have been gleaned the machinery may be used more effectively.

Jan 12, 1926

By Waldermar Lindgren

[The observations here presented were made during a short visit at Calico, in December, 1886. The accompanying map, which does not claim to be more than a careful sketch, is based on the position of a few mines obtained from Mr. F. Lewis, at Calico, and the plats in the Land Office with the patented claims. Only a few claims are shown by their boundary lines: as usual in mining districts, there is an enormous number of them, often conflicting or overlapping, the correct mapping of which would be useless for the present purpose. The rest of the topography and the drainage are mapped from sketches, aided by compass and aneroid. The elevations are taken from Daggett as base, the altitude of this station being determined by the railroad to be 2000 feet.] Until a few years ago the product of silver in California was of little importance, compared with that of gold, and often fell short of $1,000,000, the only noteworthy counties being Mono, Inyo and San Bernardino. About 1881, however, important discoveries were made in the deserts of San Bernardino, and the remarkable increase in the production may be seen from the following figures, taken from the Reports of the Director of the Mint: Silver Production of California. Of San Bernardino Co. 1883,. .. $1,460,000 $1,050,050 1884,. .. 3,000,000 2,550,000 1885,. .. 2,568,036 2,363,436 By far the largest portion of the product of San Bernardino is derived from the district surrounding Calico, although the success there has also given fresh stimulus to prospecting and mining in other parts of the county. San Bernardino borders towards the east on Nevada and Arizona, towards the south on San Diego County, California. Topographically, as well as geologically, the largest part of it belongs to the Great Basin. Broad shallow lake-beds or valleys with an elevation of 2000 to 3000 feet, are separated by low mountain chains and

Jan 1, 1887

By T. Egleston

Although the success of metallurgical operations depends so largely on the possibility of finding proper refractory materials, which enter so prominently into the cost of their operations, it can hardly be said that our knowledge of them is in a very satisfactory condition, or even that we know very much about them, beyond a few facts which have been gathered through their use. Experience, as a general thing, is an excellent master, but the requirements of

By Marshall D. Himes

The Pima mine, Pima County, Ariz., a 53,500-tpd copper mine, is located 17 miles south of Tucson, Ariz. The mine is in a sequence of Paleozoic and Mesozoic sediments striking east-north-east and dipping southeasterly. These sediments are intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian (?) dolomites, limestones, and sandstones have been altered to calc-silicate skarn, marble, and quartzite. The overlying Mesozoic Triassic (?) clastic sediments have undergone some recrystallization and hydrothermal alteration. The clastic metasediments are divided into three distinct lithologic units: lithic arenite, arkose, and interbedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite, and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar, quartz, and sericite, with or without chlorite and calcite). The porphyry has undergone potassic alteration. Dominant structures are an east-west postmineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. The two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast, and the other striking northeast, dipping northwest. Economic mineralization is prediminantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are less important amounts of magnetite, hematite, sphalerite, galena, tennantite, and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1974

By E. S. Bumps, W. F. Craig, M. Baeyertz

Metallurgists have looked at fractures macroscopically for many years and have evolved a vocabulary in which such words as "cleavage," "brittle," "shear," "ductile," "granular," "fibrous," and "silky" are used to describe the appearance of the fractured surface; but the meaning of these words in terms of metal structure is not well established. Observations of the structural meaning of "brittle" and "ductile" fractures in plate steels have been made, notably, by Kramer and coworkers1 and by Tipper.2 Grossman3 has studied the fracture of tempered martensite and combinations of ferrite and martensite. Notwithstanding these and other less concerted attacks on the problem, present understanding of fracture rests more on assumptions and logic than on experiment. It is the purpose of this paper to add a little to the growing fund of experimental observations of the nature of fractures in steel. The particular fractures to be described were obtained in conventional impact testing of an ordinary structural steel shape. In impact tests of the Charpy type, the specimens fail in a characteristic manner that depends on the steel and the temperature of testing. With ordinary structural and many other steel products, an appropriate range of testing temperature will cause a considerable change in the energy absorbed before fracture. This change is known as the energy transition and is accompanied, more or less closely, by alteration in the appearance of the fracture. At testing temperatures below the transition, the terms "brittle," "cleavage," or "granular" are used to describe the fracture; above it, "ductile" or "shear" are often used. Within the transition, the fracture changes from "brittle" to "ductile" by a progression in appearance, wherein the "brittle" portion of the fracture becomes restricted to a smaller and smaller central area of the fracture, as the testing temperature is raised and the "ductile" type of fracture is approached. All this is well known to metallurgists. The specimens under consideration are of the conventional V-notch Charpy type. They were taken from a structural steel shape of the following analysis: C Mn P S Si 0.17 0.46 0.009 0.029 0.03 Both longitudinal and transverse specimens were tested and examined. Fig 1 shows the energy values plotted against testing temperatures in the usual way. The curves for both longitudinal and transverse specimens show an energy transition, although the maximum energy absorbed at testing temperatures above the transition is greater in the case of the longitudinal specimens. Fig 2 illustrates the changes in the macroscopic appearance of the fractures that are associated with the energy transitions shown in Fig 1. Macrographs of the fractured surfaces of the specimens have been identified with the fracture ratings at intervals on each fracture curve. The numerical fracture rating on the ordinate of Fig 2 indicates the percentage of the area of each fracture that was considered to be "brittle" on macroscopic observation. Such rating of the fracture type in impact tests is now customary in many laboratories. Hereafter the specimens will be identified by reference to Fig 2 as 90 pct "brittle," 80 pct "brittle," and so on, in accordance with this macroscopic evaluation of the appearance of the fractured surface. The discussion of the fractures is divided into three parts. The first two are concerned with the mode of fracture and its relation to general structural features. As the same metal-lographic features occur in both longi-

Jan 1, 1950

By T. R. Scott

The acid pressure leaching of zinc-lead flotation concentrates from the McArthur River deposit, Northern Territory, Australia, has been studied in a three-stage, continuous, co-current system, using titanium reactors of 6 gal capacity. The starting pulp contained 2.7 lb solids per gal of synthetic spent electrolyte and the final liquors contained 120-125 gpl Zn. Parameters investigated included temperature (95-120°C), oxygen pressure (30-100 psi), acid addition (80-130% of theoretical), and leaching time (35-65 min per stage). Technical factors studied included mixing and pumping of feed, agitation, settling and washing and control mechanisms. The chemistry of liquor impurities, of scale formation in autoclaves and of lead jarosites in residues was studied in some detail. Results indicated that 90-93% zinc recovery could be obtained with a "low- acid" process, using 113°C and 70 psig with oxygen as the favored operating conditions. Residues contained 16-18% elemental sulphur and 15% lead, together with unreacted pyrite and gangue minerals. Pelletizing of residues was impracticable, and alternative suggestions for the recovery of lead, sulphur and silver are discussed. Preliminary estimates for plant and operating costs are given and enable some comparison to be made with conventional procedures.

Jan 1, 1973

By H. R. Hanley

IT is a well-known fact that the solubility of zinc compounds decreases when these compounds are roasted in contact with iron compounds, but descriptions of tests to quantitatively express the fact have not appeared in the literature. Possibly such an expression cannot be uniformly and exactly duplicated by different operators because of the variation in the personal equation. In a general way, however, the reactions between zinc compounds and iron compounds under roasting conditions will show a certain trend with changing conditions and the approximate quantitative expression of this trend appears reasonably well established by experimental work conducted for this purpose.

Jan 1, 1929

By E. DeGolyer

The only known direct method of discovering oil deposits is by the drilling of test wells. Such exploration is always hazardous and generally very costly. The problem of the prospector, therefore, is to select test sites that are favorably located and so to reduce the odds against his venture. Early in the history of the oil industry, it was realized that oil and gas deposits, other conditions being favorable, were usually found in anticlinal types of structure. This very undestandable and rational habit of occurrence furnished the first substantial clue to the prospector. Oil occurs in sedimentary rocks, and beds of such rocks are deposited originally in approximately parallel layers. An anticline at the surface, therefore, could be accepted as an indication of an anticline in lower beds. Structural geology became the tool of the prospector, and by its use in the past two decades the majority of the known important oil deposits of the world have been discovered. This is but a partial, and the simplest, statement of the problem, Nine-tenths and more of the important oil pools of the world belong to the great class of accumulations controlled by structural traps—anti-clines, faulted structures, salt domes, etc.—but by no means all of these structures are clearly or adequately expressed at the surface. As the more obvious anticlines were explored and the search for new deposits led to the testing of progressively deeper beds, it became more and more apparent that marked favorable structures involving petroliferous rocks can, and do, exist without any marked surface expression. There are great areas where the surface, covered by some masking material such as water, alluvium, glacial deposits, or sand dunes, affords no clue to structural conditions in the subsurface, and there are also regions where the surface formations are unconformable with the oil-bearing formations. The structure in which the prospector is fundamentally interested is that of the oil-bearing formation itself, together with roof and floor beds. No other geologic information is of interest or importance to him except as it affords clues to the stratigraphy and structure of the supposed oil-bearing formations.

Jan 1, 1932

By Paul Billingsley

THE term Boulder batholith was first applied in 1897 by W. H. Weed'2 to the extensive mass of granite in western Montana within whose borders occur the ore, deposits of Butte. In a general, way this was known to extend from Helena on the north to the Highland Mountains near Butte on the south, and to be relatively narrow in its east-west diameter. Its intrusive relations to the surrounding sedimentary , rocks, and its probable Tertiary age, were described by Weed, but in many ways his statements, based upon incomplete data, have required revision. Most notable of the errors of this description of the batholith were the failure,3 since corrected, to recognize the intrusive contact of the granite with the capping of andesite, and the complete absence of any reference to the many extensions of the granite beyond the somewhat narrow limits of its largest exposure.

Jan 1, 1915

By James F. Lewis

THE hematite iron ore mines east of the Hudson River are confined to a strip of country ten to fifteen miles wide, commencing on the south, near Fishkill, running northeast through Dutchess County, and striking the southeast corner of Columbia County, extending into Litchfield County, Conn., known there as the Salisbury mines, cropping out again at and near West Stockbridge, Lanesboro, and Cheshire, Mass., also in Bennington County, Vermont. The ores are found in beds or deposits and in veins, with a limestone ledge on one side and slate on the other, from six to thirty feet from the surface. Portions of it are quite solid, called rock ore, but

Jan 1, 1877

By Thomas. B. D.

GRAVITY concentration is a general term designating processes for separating and sorting granular material by means of forces that depend on the density, size and shape of the particles. When these forces are applied to the particles the latter are caused to move, those of a given density along one path and those of a different density along another, until ultimately they are sufficiently separated to be removed from the operation of the process. The forces producing this separation are in general complex and, unfortunately, no completely rigorous analysis of them has as yet been devised. The science of the hydrodynamics of viscous fluids deals with , the little that is known about the problem. Every observer of nature is familiar with the fact that an object moving in a fluid encounters a force of resistance. We have only to walk against a brisk wind or stir a cup of coffee, or observe the slow fall of a grain of sand in water, to experience directly the fact that such forces exist. The exchange of force between an object and a fluid in which it is moving operates on the fluid as well as on the object. Thus a sailboat may be set in motion by the force exerted by the wind on the sail; but the sail also deflects the wind-furthermore, the water in which the boat floats is set in motion by the force exerted by the boat as it cleaves through the water, The wind is thus enabled to do work on the water through the intermediary of the boat. In general, an object moving through a fluid encounters a force that opposes the motion and also acts to change the motion of the fluid. In gravity concentration we are dealing with this force of resistance acting on the granular particles that are to be separated. Furthermore, the motion induced in the fluid by a particle will in turn affect the motion of a neighboring particle. This effect will be reciprocated and in consequence there will be an exchange of forces between all the particles in the material. These effects are complex and the most that can be expected is that we may be able to determine in a qualitative way how they operate. In gravity concentration, then, the following types of forces may be distinguished as acting on the particles:

Jan 1, 1943

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By Oliver Bowles

While vast quantities of limestone and dolomite are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little atten. tion compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux " that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

By K. Shoji, R. Hogg, L. G. Austin

The flow of dry powders through continuous ball mills has been investigated. Based on a physical model of the system, expressions have been derived which relate the holdup of material in the mill and its variation along the length of the mill to the mill dimensions, speed of rotation, material feed rate, and the mill discharge geometry. Experimental results obtained in a small (4 in.) mill using 3/8-in. steel balls and a feed of silicon carbide particles are in good agreement with the prediction of the model.

Jan 1, 1976