Search Documents

By Paul B. Crawford, Melvin B. Burton

A procedure is given which describes how the gelatin model may be-used to study the effect of mobility ratio on areas swept before and after breakthrough in fluid injection programs. Differences in mobility ratio are achieved through the proper selection of electrolytes for the invading and displaced fluids. The progress of the front is followed visually and photographed or traced onto plates (it desirrd positions before and after breakthrough. Example applications to standard flooding pattrrrls, vertically and horizontally fractured reservoirs and the in-situ combustion recovery process ore presentrtl. INTRODUCTION In water flooding, gas cycling and other fluid injection programs, the sweep efficiencies and swept areas after breakthrough are known to depend on the mobility ratio. Previous investigators have described the application of the X-ray technique, stepwise use of the poten-tiometric model and numerical procedures for studying these problems.1,3,4,6 Others have described the application of the electrolytic and gelatin models for studying sweep efficiencies at a mobility ratio near one.2,5,7,8,9 It is a purpose of this paper to describe a procedure for using the gelatin model to study swept areas at mobility ratios other than one. PROCEDURE The technique developed for gelatin model studies is composed of four phases: the construction of the model, the selection and preparation of electrolytes, the running procedure, and the recording of the swept areas. Each phase is discussed independently in order that the over-all procedure will not be confused. Construction of the Model Since some of the advantages of the gelatin model are its economy, and speed, it is desirable to have as small a model as is possihle without creating error through the inability to follow visually the progress of the colored front. For this work, it was found that a distance of 4 to 6 cm between salt bridges is convenient to use. Since the size is relatively small, it follows that the gelatin layer must be thin. For this study, 1/8 in. was used as the gelatin thickness in each case. The model was constructed on a flat 1/2-in. plastic (Lucite) base with boundaries constructed from 1/8-in. plastic strips. The well pattern to be studied was outlined with the 1/8-in. plastic strips on the base with narrow apertures (- - 2 mm) in the boundary to represent the wells. Behind each well opening, a rectangular area of some 8 to 12 sq cm was outlined by additional plastic strips. The plastic strips were fastened to the base by any suitable non-conducting cement so that the boundary system was liquid tight. The electrodes were constructed from sheet copper in a fashion that would allow easy removal. In this work, it was found that by simply forming a large U-shaped clip from a strip of the copper that would slip over the boundary was satisfactory and easily removed. The electrodes should be as wide as one of the sides of the rectangular area behind the well opening. If a fractured pattern is studied, fractures inside the well pattern may be represented by strips of copper of the desired shape mounted in some easily removable fashion. The reason that apertures (or salt bridges) were used for wells instead of metallic electrodes is that the plating of the electroactive ion at the cathode and the introduction of an electroactive ion at the anode has a detrimental effect on the swept area outline if these operations \rere permitted to be carried on within the well pattern itself. The anode may be used within the well pattern

Jan 1, 1957

By B. L. Sackett

In a general way, the situation in copper smelting is quite similar to that of lead smelting. In other words, the introduction and successful flotation of copper ores has tended to decrease greatly the tonnage to be handled by the smelter and therefore has resulted in curtailed smelter operation. However, copper production has increased rather than decreased. The general effect of flotation has been to decrease the number of furnaces operating, but it has also increased to a considerable extent the difficulties in handling the material, just as was outlined in the case of lead smelting. In copper smelting, the flotation concentrates must be roasted and prepared for the reverberatory furnace. Handling Flotation Concentrates The handling of copper flotation concentrate, which is more or less wet and mucky, is more difficult than was the handling of the old gravity concentrate. Also, the roasting of the concentrate and the handling of the calcine produced is more difficult. That is mainly because the material is extremely fine and the tendency to higher dust losses is greatly increased. The draft in the roasting furnaces must be kept as low as possible, and the feeding of the calcine into the reverberatory furnace must be done carefully, so that dust losses may be kept at a minimum. Transition Stages oF Concentration and Smelting The general process through which the copper smelter has gone as a result of flotation has been somewhat as follows: In the relatively old days, when copper ores of low grade were first treated, a large number of furnaces were required, and naturally comparatively poor recoveries were made. Also, the profits on low-grade ores were small and the handling of those ores was possible only because of the large tonnages. Then came gravity concentration, which was a great improvement but which only incompletely removed the gangue material, the insoluble and the iron, from the copper ore, and made comparatively poor copper recoveries. This still left a considerable amount of insoluble and iron, as well as the copper itself, to be treated at the smelter.

Jan 1, 1928

By John Rear Admiral Edwards

Introductory.-There are many interesting and important events connected with the petroleum problem. The remarkable men who conceived the thought of transporting petroleum by pipe line, conserving the by-products of the commodity, and conducting extended investigation and research whereby the flash point of the oil was raised, its cost reduced and its Supply assured, are deserving of the gratitude of this nation. It was primarily the success attained by Captain Lucas, after his comprehensive search for oil in Texas and Louisiana, that was the impelling cause. which 'prompted the Navy Department to conduct the extensive series of liquid fuel-oil tests that were made from 1901 to 1903. The sensational discovery of oil at Spindle Top made a deep impression upon Rear Admiral George W. Melville, then Engineer-in-Chief of the Navy, and the discovery of the vast oil field in Texas convinced him that, within a generation, if not within a decade, crude petroleum was going to play a very important part in warfare, and that the commodity might possibly develop into a necessary munition of war. The United States' Commanding Position as a Petroleum Producer.¬ In the study of the various problems relating to the world's production of crude petroleum, the position of the United States is one of commanding importance, whether viewed from the industrial or the military aspect. The present yield of this country is practically double that of the rest of the world, and, in view of the productive and prospective fields possessed by various countries, together with the comprehensive and exhaustive search that has been made throughout the world for petroleum, it is extremely probable that this lead will be maintained for the next decade. As regards the character of the crude-oil yield of different countries, America possesses the greater part of the supply that contains a paraffine base, and therefore a considerable portion at least of the American product produces the best illuminant. Of all the crude-oil distillates, kerosene is in many respects the most important, and the Appalachian product for this purpose is favored, particularly in the Far East, above that of any other petroleum yield of the world.

Jan 9, 1914

By Walter R. Hibbard, Robert I. O’Herron, Fred D. Rosi, Howard T. Clark

INTRODUCTION AND PREVIOUS WORK IN the search to find a copper-base alloy with high strength properties, it was considered that the addition of a small amount of an age-hardening element to a binary system with useful strength properties might result in a series of alloys of theoretical and practical importance. [ ] The copper-nickel system was selected for its basic properties and chromium was added as the age-hardening element in view of the small percentage involved and its decreasing solubility with decreasing temperature. A study of the Cu-Cr binary alloys was undertaken as a preliminary investigation. However, in view of the response of these alloys to heat treatment, the scope of this phase of the investigation was widened. [ ]

Jan 1, 1948

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933

By Joseph L. Gillson

YOUR speaker has long sought an opportunity to review the many differences between the subject matter called economic geology and the duties of a practicing economic geologist. As the subject was taught in my student days, professors teaching courses in economic geology paid little attention to what we now call industrial minerals. Certainly they were not concerned with problems involving production and marketing, but only with the origin of such mineral deposits as the Stassfurt potash deposits; with other evaporites, such as salt, gypsum, and Chilean nitrate; with the possible modes of formation of sulfur in salt domes; and the causes of asbestiform mineralization. Of course, much time and thought was given to the mineral identification and sequence of deposition of the minerals in pegmatites. The fact that such deposits actually produced commercial feldspar, mica, beryl, and lithium minerals for sale in industry was of minor importance. These observations lead us to pause to inquire, perhaps facetiously, what is and what is not to be included in the science of economic geology?

Jan 5, 1957

By G. Sachs, G. Espey

SIMPLE methods can be used for the determination of the residual stresses in thin-walled tubing if the stresses consist of high tensile stresses at the one surface and high compressive stresses at the other surface Such a stress distribution is approximated in sunk tubing and in deep-drawn shells It is possible to cut sections from such articles in such a manner that a major part of the residual stress is relieved by a bending of the part that is separated from the adjacent metal The circumferential stress is evaluated from the change in diameter D, occurring on splitting a length of tubing (Fig Ib),1-5 or from deflection resulting from the cutting out of a circumferential tongue (Fig Ia) G The bending moment M released by such a flexure is [ ] The release of this bending moment corresponds to the release of stresses, which, in a thin section, vary linearly from one surface to the other, and have the following value in a particular fiber a certain distance (zx from the surface [ ] where C is the section modulus and d is the thickness of the section, the ratio AI C being d 2 for a rectangular section* The maximum stress values at the surfaces are [ ] For most purposes the simpler equations [ ] will be satisfactory, where Dm is the average of the mean diameters of the tubing

Jan 1, 1941

By Newell Hamilton

Some years ago, in the manufacture of seamless tubing from an alloy steel containing 0.07 per cent maximum carbon, 18 per cent chromium and 8 per cent nickel, at the plant of The Babcock & Wilcox Tube Co., a peculiar type of piercing defect was noticed. This defect was definitely associated with certain heats of the alloy and was independent of any of the variables of mill operation and billet-heating condition. A thorough analysis of the defective material yielded but one clue to the reason for its abnormal behavior in piercing and that was its oxygen content as determined by the vacuum fusion method. The oxygen content of the defective 18-8 alloy was found to be from two to three times that of the material that had pierced satisfactorily, and this incited an active interest in the vacuum fusion method for the analysis of alloy steels. After a critical survey of the literature on this subject, and considerable experimentation, an apparatus and technique were evolved that gave a fairly rapid, simple and reliable method of analysis. Samples selected from six years of tube production of 18-8 and other corrosion-resistant alloys were analyzed by this method. This paper describes the procedure and gives a correlation of the oxygen, hydrogen and nitrogen contents of a number of alloy steel samples representative of good and bad tube-piercing quality. The Apparatus Basically the apparatus used in this work was that of Jordan and Eckman,' employing a high-frequency induction furnace and the gravimetric method of analyzing the evolved gases, nitrogen being excluded from the determination. In addition, a magazine-type cap and a large-

Jan 1, 1934

By L. C. Snider

During the past few years a number of large and highly productive oil fields have been discovered in the United States. The immediate oversupply which has resulted, together with the circumstances under which the new fields have been operated, has created exaggerated impressions of the importance and magnitude of these fields. Statements as to the many years during which individual fields could supply the entire demand of certain areas, as to the overwhelming effect of these fields on the industry, and as to their greater size compared with any of the older fields have become so common as to attract little attention. For example, East Texas is commonly considered as the "greatest oil field" and a review of the development of the field for 1931 is so headed in one of the leading trade journals.' East Texas is unquestionably a very great oil field. However, some students of the field have estimated its ultimate recovery at about one billion barrels, and the Bradford field discovered in 1875 is also estimated, by competent engineers, to have about a billion barrels still recoverable by water drive, in addition to more than 300,000,-000 bbl. it has already produced. If East Texas should produce the two or three billion barrels assigned to it by more optimistic estimators, it will, though considerably greater than Bradford, still fall far short of it in importance to the industry. A reasonable doubt also exists as to whether East Texas will exceed the Midway-Sunset field which has produced about 720,000,000 bbl. and still has important reserves. Again, in importance to the industry, Midway-Sunset has been greater than East Texas can ever be. Relative Importance of Oil Fields The principal purpose of this study is to compare, on the basis of their importance to the industry, a considerable number of the major fields which have been developed in the United States. Some remarks are also made as to the estimates of reserves in certain fields now in course of development, since the writer believes that the conditions under which these fields are operated lead to estimates of recoverable reserves which

Jan 1, 1933

By Oren C. Baptist, Eliot J. White

Samples of four reservoir sands having different degrees of water sensitivity were subjected to several laboratory tests to determine differences in capillary behavior attributable to clay-mineral effects. The degree of water sensitivity was estimated by the difference between gas and water permeability. Unsaturated pore volumes determined with mercury injection were comparable to irreducible water saturations determined with the semipermeable bar-rier method only for the non-sensitive sands that contained small amounts of non-swelling clay minerals. Irreducible saturations were independent of salinity of the water, which suggests that most residual water is adsorbed 0.7 a film over solid surfaces and that internal retention by clay minerals is relatively insignificant. The water-sensitive sands imbibed water to higher saturations than did non-sensitive sands, and this result is believed to be a combination of the effects of clay minerals and preferential wettability; however, the relative importance of each of these effects is riot determinable. Thus it is concluded that the semipermeable barrier method is the best of the laborafory methods used for estimating formntion water .saturations in the sands studied. INTRODUCTION This investigation is a continuation of studies of the role of clay minerals in petroleum production in the Rocky Mountain area. Previous work has shown large differences in gas and water permeability in numerous reservoir sands; these water-sensitivity effects observed in the laboratory have been correlated with well behavior in the field, and the degree of water sensitivity imparted to reservoirs by the various clay minerals has been determined.'.' The effect of interstitial clay minerals on formation water3 saturations is not so well known. It has been reported that formation water saturations probably are higher in clayey than clean sands,' but this effect has not been evaluated in the laboratory, and the relative effect of the various types of clay minerals on formation water saturation has not been determined. The clay-mineral groups of most importance to this study and to petroleum production in general are kaolinite, illite, and montmorillonite. The minute layers of montmorillonite are loosely bound to one another so that water enters between them, causing great expansion of the particles. Kaolinite and illite do not exhibit interlayer hydration, but they do immobilize considerable amounts of water owing to their large surface areas, which are of the order of 15 to 97 m2/gm of clay.5 The four Wyoming sands used in this study were selected to represent a wide range of water sensitivities. These sands, with the number of wells and fields from which the samples were obtained, are: Second Frontier, five wells in two fields; Newcastle, six wells in one field; Tensleep, two wells in two fields; and Lower Muddy, five wells in one field. EXPERIMENTAL METHODS AND PROCEDURES Water-displacement data were obtained by the semipermeable barrier method," using both fresh water and brines having either 16,500 ppm sodium chloride or calcium chloride. A displacement pressure of 35 psi was found to be sufficient to obtain the practical irreducible water or brine saturation (IWS, IBS) in most samples. Mercury-injection data were ob-tained with equipment and pro-cedures similar to those described by Purcell.7 Exceedingly high pressures are required to attain complete mercury saturation by this method; however, since saturations in most samples change very little with large pressure increases above 1,000 psia, the maximum pressure used was 1,400 psia. To facilitate comparison of mercury-injection and water-displacement results, it is convenient to express mercury-injection data in terms of unsaturated pore volume. The abbreviation, (100 - SHg)min, is used to denote the pore volume unsaturated by mercury at 1,400 psia injection pressure. Gas permeabilities, ki, were deter-mined by the method proposed by Klinkenberg.8 Methods of determining types and amounts of clay minerals by X-ray diffraction analyses, as well as methods of determining water permeability, have been described previously.' The imbibition characteristics of

Jan 1, 1958

By L. Alan Weakly

The first all-hydraulic drill introduced in the US began test drilling in a Missouri under round lead mine in mid-1973. Since that time, the hydraulic drill concept has slowly, and sometimes haltingly, come of age. Now, backed by impressive performance records and operator acceptance, hydraulic drills promise to produce a quantum leap in mining efficiency and, sometimes, major changes in mine and quarry engineering.

Jan 10, 1979

By D. V. Fites

Criteria for deciding when rock should be ripped and what ripping equipment and techniques should be used in given situations are discussed in this article. The relation between ripper performance and seismic wave velocities in various types of rock is also discussed. The ripper is not a new tool. In fact, it dates back as far as the Roman Empire. The Roman's ripper-mounted on wheels and shaped something like a plow — was pulled by oxen and used to loosen the earth for the shovelers and basket carriers building the Appian Way. There are records of rippers being used in this country in railroad construction between 1860 and 1880. However, the ripper as we know it today did not appear until about 1930. Tractor-drawn models were in use in 1931 on the Hoover Dam project. At that time they weighed about 7500 lb and were pulled by tractors with about 75 flywheel hp and up to 30,000 Ib total weight. The chief shortcomings of trailed

Jan 1, 1969

By K. C. Heald

THE places where, yesterday, oil was unknown contain tomorrow's fields. Unquestionably, some states that now yield little or no oil have great potentialities, and developments in these states, although perhaps of less immediate interest than those in regions where great pools now exist, may easily be of greater ultimate importance than the results of exploration closer to known fields. Not long ago, Montana had only a quarter of an oil pool, and that was regarded by many as an accident that had strayed from Wyoming. More recently, the northern line of Louisiana was a dead line that would not be crossed by any Louisiana operator who valued his reputation for sanity. Within the past few months, Colorado has shown that it is far from being a negligible factor in the oil supply of the Rocky Mountain states, and it is now known that western Kansas, long shunned by many reputable geologists and operators, should be reckoned with. There may be a vast difference between what a wildcat well yields and what the well signifies. The fact that no commercial production is encountered may be lamentable and may well be disastrous to an individual or a company, but the same well that spells ruin to one may convey to another the information that will result in opening a new field. In presenting the conclusions, in this paper, the writer recognizes fully the possibility of erroneous deductions, particularly since he has had contact with only a few of the wells that are mentioned. Information comes principally from the scout. maps and files maintained at the Geological Survey by M. E. Latimer and G. K. Drach, without whose cooperation this summary would not be possible, supplemented by some personal contact and second-hand information gained by. conversation and correspondence. However, it is felt that the data contain few errors, and that the conclusions are at least reasonable.

Jan 3, 1924

By Donald W. Scott, Adam L. Wesner

THE inevitable depletion of Mesabi direct-ship- ping iron ores, hastened by recent wars, has increased the importance of developing methods to concentrate iron-formation materials. Many mining companies, independent research organizations, chemical companies, and equipment manufacturers are devoting attention to this important work. It is only natural that magnetic iron-formation materials have received major emphasis, since magnetic recovery methods apply and reserves of Mesabi magnetic taconites are large. However, the non- magnetic* iron-formation materials are likewise believed to represent a large reserve and their study has not been neglected.

Jan 6, 1954

By Donald R. Reichmuth

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks."1 There are now three distinct approaches being used to determine the tensile strength of brittle materials. These are shown schematically in Fig. 1. The first method consists of simply pulling the specimen apart by applying an axial load. Although this procedure is the easiest to understand, the technical problems encountered during testing are numerous. Specimens cannot be readily fabricated into dumbbell-shaped specimen* like those customarily used for testing inetals. Cylindrical specimens cannot be loaded in jaw-clamps because adverse stress conditions arise at the clamping points, which causes unreliable results. An innovation developed by Niles Grosvenor at the Colorado School of Mines, in which the load is applied through steel-end caps glued to the ends of the specimens, has considerable merit, hut the samples are costly to prepare.2 All tests using a direct pull are further handicapped by the possibility of small amounts of bending being present, the specimen's surface condition, and

Jan 1, 1968

By D. L. Pentz

The use of "probability" methods in slope stability analysis has been practised by geotechnical engineers for some time. This paper questions whether the term probability has been properly used since in many cases the term is used in a classical statistical manner only to describe frequency distributions of data. This paper proposes a definition of the term probability which includes the engineers' subjective state of confidence for all critical parameters. Such parameters may include the slope stability model, undetected structural features, strength, groundwater pressure distribution, and geological framework. This process does not make a "better" analysis but it does force the geotechnical engineer to state his opinion in such a manner that others can understand and if necessary, criticize the assumptions. Further, this technique forces the question, "What impact would failure of a slope have on the production schedule or costs of a mine?" The level of risk taken in adopting a particular slope design strategy in a mine is not a question of what Factor of Safety should be selected but, rather, what trade-offs result from steeper slopes and the associated costs of failure. This paper also presents several simple probabilistic techniques which, though widely used in other fields have been all but ignored in geotechnical slope stability analyses. These include the use of stratified sampling to optimize Monte Carlo uncertainty approaches, and the use of simple functional approximations rather than complex stability models in probabilistic analysis. The author presents a case example of this technique and discusses the results in comparison with more traditional methods.

Jan 1, 1983

By Raymond Mancha

THE number of installations of propeller mine fans completed during the years of 1936 and 1937 is evidence of the increasing popularity of the propeller fan with the American mining industry. During the period from 1931 to 1936, there were several different low-pressure, low-efficiency propeller fans available, which filled a definite need in replacing inefficient centrifugal fans operated at comparatively low pressure by means of purchased power. Since 1936, however, the trend toward the propeller fan has greatly increased, as propeller fans are now available practically without pressure limitations and capable of efficiencies high enough to warrant replacement of efficient centrifugal fans in many instances. Few manufacturers of propeller mine fans base their fan-operating characteristics upon similar test methods, primarily because of inadequate facilities for testing in the factory and the need of a test code incorporating a calibrated duct or nozzle that makes possible the testing of large propeller fans quickly, accurately and without prohibitive expense and space requirements. As a result, fan manufacturers have resorted to various methods for testing large propeller fans in the factory, and different yardsticks have produced uncomparable and often inaccurate performance data. It is the purpose of this paper to describe and discuss in detail the test procedure of the Jeffrey Manufacturing Co., which has been proved both accurate and practical. Fig. 1 shows a plan, a side elevation and two end elevations of the test duct with a propeller fan of the exhaust type in place. Testing propeller fans exhausting permits greater accuracy than testing these fans blowing, because in the former uniform flow conditions are more easily established at Pitot tube stations where fan pressure and air-volume measurements are desired. Any residual rotation remaining in the air discharged from a propeller fan blowing into a test duct must be removed before an attempt is made to obtain accurate pressure and volume readings. Although various devices for straightening the air may be placed between the blowing fan and the volume-measuring station without resulting complications, uniform flow so obtained at the pressure-measuring station necessitates corrective calculations to compensate for duct resistance

Jan 1, 1939

By J. D. Miller Discussion by N. P. Finkelstein, M. C. Fuerstenau

The point designating 10 -4 nole/per liter sulfonate addition in Fig. 1 has been presented incorrectly. This figure, with the corrected scale, is shown at right. N. P. Finkelstein (National Institute for Metallurgy, Johannesburg, South Africa) - The qualitative conclusion the authors of this paper have reached in evaluating the influence of hydrocarbon chain length on collector effectiveness agrees with conclusions in several published reports. However, in two other

Jan 1, 1969

By W. A. Koehler, M. E. Hinkle

THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: 1. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of ferrous (iron) sulphate and some sulphuric acid. 2, The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages normally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio-6aciZZus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not Yet been established. Apparently it does not Promote the oxidation of ferrous iron compounds in mine drainage to the ferric state. The second organism has not been identified by name but is described as " Gram negative, non-spore-forming rods approximately 0.4 micron wide by 0.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur compounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced Percentage of Oxygen and increased percentage of carboll 'dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. Acid Coal Mine Drainage Acid coal mine drainage has been the concern of coal mine operators, industrialists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1949

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950