Search Documents

By E. R. Gilliand

KNOWLEDGE of a large number of the physical properties of the hydro-carbons is needed in the calculations and studies of the production engi-neer. Since experimental data on these properties of the individual hydrocarbons and their mixtures are available in only a relatively few cases, the use of generalized correlations has developed rapidly in the last decade. The generalized correlations of pressure, volume and tem-perature,1 enthalpy,2 and vapor-liquid equilibria,3 on the basis of reduced temperatures and pressures, are outstanding examples of this develop-ment. These correlations are of particular value to the production engineer interested in the flow of oil and gas, since they can be used to estimate the conditions under which segregation of phase occurs as well as the composition, density, and relative amounts of the phases. The technique of using the correlations for such estimations has been pub-lished by several authors¢ and will not be considered in this paper. A considerable number of data have been obtained to check the generalized pressure-volume-temperature correlations, and these data indicate that such relations hold for the hydrocarbons from methane to heptane. The accuracy is in general sufficient for most engineering pressure-volume-temperature calculations. However, the generalized correlations of enthalpy and vapor-liquid equilibria have in general been developed from the pressure-volume-temperature correlations by thermodynamic calculations and only a relatively few experimental data are available to check these calculated values. The calculations from pressure, volume and temperature are likely to lead to large errors in the calculated enthalpy and vapor-liquid equilibria. Thus, in the calculations of enthalpies, slopes of the pressure-volume-temperature data are employed, and determining these slopes can greatly amplify small errors in the original data. In the vapor-liquid equilibria calculations it is necessary to have the pressure-volume-temperature relations of the mixture, and the latter properties are much more questionable than those of pure components, particularly in the critical region. A considerable number of experimental data are

Jan 1, 1939

By Earle E. Schumacher, W. C. Ellis

For the purpose of developing combinations of higher strength and conductivity than are obtainable by heat treatment alone in the age-hardening copper alloys, an investigation has been made of the effects of combinations of heat treatment and strain hardening on the properties in question. The investigation was limited to a study of the alloys containing nickel and silicon; nickel, silicon and cadmium; and cobalt and silicon. The experiments made in the course of the study arc described in this paper in three groups: 1. The effect of hard drawing subsequent to heat trcatment on the mechanical and electrical properties of the alloys. 2. The effect of low-temperature aging on the properties of heat-treat,ed and hard-drawn alloys. 3. The effect of strain on the rate of aging of quenched nickel-silicon-copper alloys. Preparation and Compositions or the Alloys The alloys were prepared by melting cathode copper in an electric resistance furnace and adding sufficient of the hardening elements to bring the compositions to the desired values. The purities of the hardening elements were as high as could be obtained in commercial practice. The metals were what are designated in the trade as electrolytic nickel, cobalt rondelles, commercial stick cadmium and fused silicon. The alloys

Jan 1, 1931

By J. L. Moriarty, Irving Johnson, H. M. Feder

The crystallization of ternary alloys has been studied as a coprecipitation phenomenon by measuring the substitutional carrying of trace metals with CeCd11 precipitating from liquid cadmium. The Doerner-Hoskins logarithmic distribution law has been found to apply in all cases; the coprecipitation coefficients obtained were: 1.48 (La), 1.06 (Th), 0.63 (Pr), 0.24 (Gd), 0.17 (Sm), 0.13 (U), 0.10 (Er), 0.09 (Sr). Li, Na, K, Ba, Y, Sc, and Zr were not measurably carried. It has been observed that coprecipitation was most extensive for those tracers which form with cadmium an intermetallic compmdnd isostructural with CeCd11 or closely related thereto. For these tracers an inverse relation between Solubility in cadmium and coprecipitation coefficient was noted. THE partition of impurities between the liquid and solid phases of a metal or a congruently melting intermetallic compound has been extensively studied by the methods of zone melting.' However, when the composition of a liquid alloy and of the solid phase crystallizing from it differ grossly, partition of an impurity cannot be investigated in this manner. Partition of the impurity under equilibrium conditions may be studied by investigation of the appropriate phase diagram and partition under nonequi-librium conditions may be studied by observation of coring in the solidified alloys.2 The nonequilibrium case is of special interest in metallurgical practice because many complex alloys are cooled too rapidly to permit the uniform diffusion of impurities throughout the crystallizing phase(s). With this in mind, the present study was undertaken to obtain quantitative data on the phenomenon of coprecipitation via substitutional solid solution in certain metallic systems. It will be noticed that rather than adopting metallurgical ter- minology we have chosen to refer to the partition of impurities during alloy crystallization as coprecipitation.3 In the terminology of coprecipitation the impurity is referred to as the tracer and the precipitating phase as the carrier. From aqueous solution, coprecipitation may occur as a result of adsorption on the surface of the carrier, by occlusion of the liquid within the crystals, or by solid solution of the tracer in the carrier. By slow cooling of liquid metallic solutions it is relatively easy to form large, regular crystals of the carrier; the effects of adsorption and occlusion may be minimized and the influence of substitutional solid-solution formation may be made to predominate. Previous studies of the crystallization of some intermetallic compounds4 and of copper, silver, and gold5 have shown that the coprecipitation or partition behavior of trace metals is entirely analogous to that observed in aqueous systems when ionic substitution occurs, e.g., coprecipitation of Ra++ with BaSo4. The precipitation of CeCd11 from liquid cadmium was chosen for study. This choice was influenced by the following consideration. If the relative atomic sizes of the tracer atom and the atom for which it substitutes determine the tendency to coprecipi-tate, then a lattice having a substitutional site of well-defined size would be desirable. In CeCd116 (structure type cubic BaHg117) the cerium atom is completely surrounded by a cage of twelve nearly equidistant cadmium atoms. Thus, atoms much larger or much smaller than cerium should be poorly accommodated in this cage. The choice of a lanthanide central atom allowed the testing of the size hypothesis with a number of lanthanide tracers which differed in size but not in valence or electro-negativity. EXPERIMENTAL The general technique of this investigation was to prepare a slightly undersaturated solution of carrier in liquid cadmium to which a tracer was added. The concentration of tracer was always so low that saturation over the entire temperature range investigated was never exceeded. The solution was cooled in a stepwise fashion. After each step a por-

Jan 1, 1964

By J. R. Dolegowski, W. S. Jensen, S. M. Olafson, W. H. Champion, G. A. Kordosky

The use of pH control in solvent extraction circuits to aid in metal separation, concentration, and purification is an extremely useful technique applicable to a wide range of solutions. This paper discusses the technique in general and then gives examples of its use in extraction stages, wash and/or scrub stages, and in stripping stages, to effect the desired metal separation, concentration, and purification. Specific examples cited include Cu-Ni, Cu-Zn, and U-Mo separations using commercially available liquid ion exchange reagents.

Jan 1, 1982

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. A. J. MAY is Engineer in Charge of Shaft Sinking, Ground Hog Unit, American Smeling and Refining Co, Vanadium, New Mexico. El Paso Meeting, October 1948. TP 2737 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Nov. 29, 1948; revision received June 22, 1949. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A Yzx4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four % in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of % yard capacity, both manufactured by Blaw-Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1951

By A. J. May

THE Star shaft is near the north boundary of the group of mining claims belonging to the Ground Hog Unit of the American Smelting and Refining Co., near Vanadium, N. Mex. The shaft bins and surface plant are served by a siding from the Atchison, Topeka and Santa Fe railroad, and this factor of railroad transportation influenced the choice of site. This paper describes the shaft sinking only, and does not cover the surface plant or other parts of the mine or its equipment. A. J. MAY is Engineer in Charge of Shaft Sinking, Ground Hog Unit, American Smeling and Refining Co, Vanadium, New Mexico. El Paso Meeting, October 1948. TP 2737 A. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Nov. 29, 1948; revision received June 22, 1949. Experience with this shaft seems of interest because of the mechanical mucking, good rate of progress, and the costs obtained at the present level of labor and material costs. The shaft has four compartments, as shown in fig. 1. Equipment: Riddell Mucker: The mucking was done by a clamshell bucket and a Riddell mucker, which, as in other shafts sunk with this machine, consisted of a carriage mounted on axles with double flanged wheels that traveled back and forth on a swinging track, parallel to the long axis of the shaft (fig. 2 to 6). Three air motors were mounted on the carriage; one hoisted the clam, one operated the bucket opening and closing device, and the third moved the carriage along the track. The carriage was designed with guide shoes and could be hoisted to the surface in either skip compartment without trouble (fig. 4). During blasting operations the clam was tied on the rails and the carriage was hoisted up a few sets to protect it from flying rock. No attempt was made to hoist the carriage and clam together lest the clam catch in the timbers. The track on which the carriage operated was built of extra heavy 6 in. pipe with 1x2 in. strap welded on top for rails. A Yzx4 in. angle was welded on the bottom of the 6 in. pipe with a 1 in. round rod welded in the angle for a filler and additional strength. The end or cross pieces of the track which kept the track to gauge, were also made of reinforced, heavy 6 in. pipe and were bolted to the long members on which the carriage traveled (fig. 2 and 3). This section of track was used, instead of heavy railroad rails, for two reasons: (1) this section would bend before it snapped and was much safer for the men in the bottom; and (2) it was a better blasting shield, and protected the timbers better, in fact, only five wall plates were broken by blasting in 1926 ft of shaft, although 150 to 225 lb of 40 pct powder was loaded per round, depending on the ground conditions. The swinging track was supported by four % in. hoisting cables anchored to the end plates. There were also four safety cables fastened two to three sets above the carriage, which would catch the carriage if one of the supporting cables should fail for any reason (fig. 7). Clamshell Buckets: Two clams were used, each of % yard capacity, both manufactured by Blaw-Knox, Nos. 662 and 663. The No. 663 clam was 4 in. wider and 5 in. shorter than the No. 662, but seemed to dig and load more satisfactorily. It was easier to hoist and lower when it came up for repair. It did not turn over as easily, had less spill

Jan 1, 1951

By M. H. Richman, E. S. Meieran

An analytical method is presented which enables the electron diffraction patterns from a twinned region to be indexed. The method has only been applied to (112) twins in bcc lattices, but can easily be adapted to other types of twinned lattices. Calculations of all twin spots, including those superimposed on matrix spots, is made possible by this method. SINCE the advent of transmission electron microscopy, the analysis of selected-area electron diffraction patterns has become very important in the interpretation of electron micrographs. Frequently, as in the case of some martensites, twinned areas are observed and give rise to complex diffraction patterns, which so far can be analyzed only for the simplest orientations of the thin foil specimen with respect to the electron beam. In order to simplify the analysis of twin patterns of more complex orientations, an analytical method was devised which is capable of predicting the positions of all reflections from both matrix and twin regions for all possible foil orientations. Although the method has only been applied to the case of bcc metals twinned about a (112) plane, it is equally applicable to other Bravais lattices. This method has been successfully applied to selected-area electron diffraction patterns of Fe-Ni and Fe-Ni-C martensites and drawn tungsten wire. PROCEDURE Imagine the reciprocal lattice corresponding to a bcc material, with each point hkl representing the crystallographic plane (hkl). Since the extinction conditions require that for this lattice, only reflections where h + k + 1 = even integer are allowed, the three dimensional reciprocal lattice is actually fcc. Since in real space twinned regions and matrix regions are mirrored across a (112) plane, the twinned reciprocal lattice is derived from the matrix reciprocal lattice by a rotation of 180 deg about a (112) direction. While it is possible to calculate how a point hkl will shift under a twinning transformation to a new point htktlt using only the reciprocal lattice based on the orthonormal vectors [100], [010], and [001], the calculations are greatly simplified if a new orthonormal coordinate system containing the twin axis is introduced. The twinning operation then becomes a simple rotation of 180 deg about a principal coordinate axis (in this case the twinning axis), and a retransformation back to the original reciprocal space will give the position htktIt of the twinned reflection.

Jan 1, 1963

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

This paper presents details of the concept that size reduction in comminution machines takes place by three mechanisms; namely impact, abrasion, and chipping grinding. Experimental evidence is presented to show that each of these comminution mechanisms produces particles of a characteristic size distribution. The actual product from a comminution device has been postulated to be the result of a composite of these three types of mechanisms. Composite curves are demonstrated for a material following the Gaudin-Schuhmann, Gaudin-Meloy, and Rosin-Rammler size distributions. About forty years ago, Gaudin1 showed that grinding may be considered a combination of impact and attrition. Since that time, major efforts have been devoted to studies, both experimental and theoretical, of impact and compression fracture, while attrition has been almost wholly neglected, at least quantitatively. A significant attempt to distinguish between attrition and impact grinding is the work of Tanaka2 in Japan. By means of an instrumented abrasion grinder and a drop weight device, he determined coefficients relating the increase in surface area of various materials to the energy expended by the two methods of comminution. He showed that physical properties of a material determine its response to attrition and impact grinding. By extending his ideas to ball milling, he concluded that to a large extent the basic comminution process in a ball mill is due to the impact of falling media. Because Tanaka used a mass of particles in his drop weight device, however, he did not obtain pure impact size reduction. The purpose of this paper is to define basic mechanisms of size reduction, to verify that each has a characteristic and meaningful distribution curve, and to show how a combination of these mechanisms results in a size distribution very like that produced by grinding mills. DEFINITION OF COMMINUTION MECHANISMS The product from a grinding device will be considered to be the sum of the contributions resulting from the action of three basic mechanisms of size reduction which operate in a ball and rod mill. These are impact grinding and two forms of attrition, namely abrasion grinding and chipping grinding. Each is defined below. Impact Grinding: If a straight line is obtained when the cumulative weight fraction finer than a given size is plotted on log-log paper as a function of that size, the slope of the line is defined as the distribution modulus. A number of investigators 3,4,5 have shown that impact fracture of single specimens of different composition and shape results in a distribution of daughter particles that exhibit a distribution modulus of unity. This has also been true for materials broken in slow compression. Moreover, under slow compression or impact fracture conditions, theoretical distribution equations6*' which approximate the Gaudin-Schuhmann distribution when the distribution modulus is close to unity agree reasonably well with the experimentally obtained products. If one now considers a comminution process where many impact or compression fracture events are taking place, then any rational summation of the individual events yields, in the finer size range, a Gaudin-Schuhmann distribution whose distribution modulus is also unity. If the size distribution of the product from a mill has a distribution modulus of unity, it is implied that particles are fractured in a manner which results in a comminution event having a distribution like that obtained for the breakage of single specimens. These impact events would occur when a particle is smashed between balls or between a ball and the mill liner. Attrition, on the other hand, is that form of grinding which cannot be called impact grinding, and comprises both abrasion and chipping grinding. Abrasion Grinding: Abrasion is a form of surface wear resulting when particles rub against each other or against balls or the mill liner of a tumbling mill, somewhat like a piece of wood being rubbed over a piece of sandpaper. The surface wears at a more or

Jan 1, 1964

By R. S. Wagner, H. Brown

Criteria for nucleation with the aid of twin planes during crystal growth from the melt are discussed. It is shown experimentally that bismuth crystals can grow from a subercooled melt in a twinned bismdtic form. A mechanism of growth based on the presence of at least me twin plane is proposed. It is well known that faceted growth can be observed in crystals grown from the vapor phase, dilute solutions, or from the melt. Faceted growth, in which the crystal is bounded by its slowest growing faces, will occur if the growth rate is strongly orientation dependent. The addition of atom layers on a facet plane can only occur by two-dimensional surface nucleation or with the aid of an imperfection. Nucleation with the aid of dislocations was proposed by rank' and observed to be of particular importance in crystal growth from the vapor phase. Nucleation with the aid of two-dimensional imperfections, notably twin planes, was suggested by stranski2,3 and Frank.4 A twin plane, terminating at the growth interface, can form a reentrant step at which nucleation can occur at a much smaller super-saturation (or supercooling) than required for two-dimensional surface nucleation. Nucleation by a twin plane usually results in a fast growth rate along a crystallographic direction parallel to the twin plane. Such a nucleation mechanism, based on the presence of a twin plane, has been used by Dawson5 to explain the growth and morphology of sheet-like crystals of paraffin n-hectane. In recent years more evidence was found that nucleation by twin planes occurs frequently in crystal growth from the vapor phase and from dilute solutions, for example, in cadmium,' barium titanate,7 silver,8 silicon9 and gallium arsenide.10 In crystal growth from a supercooled melt, however, nucleation by twin planes has so far only been observed in materials with the diamond or zinc blende structure. Bennett and Longini11 were the first to recognize the important role a single twin plane plays in the growth of germanium dendrites. Subsequently, it was found that a prerequisite for continued propagation of germanium dendrites is the presence of two parallel twin planes which form a self-perpetuating system of nucleation sites.12 Sili- con and some III-V compounds such as InSb also grow dendritically by twin plane nucleation. It appears that the following criteria must be satisfied in order that nucleation with the aid of twin planes can occur: A) The growth form of the material must be faceted." B) The formation of twin boundaries, by a fault in layer sequence during growth, by plastic deformation, or by an accidental meeting of properly oriented crystals, must be possible. C) Twinning must form a reentrant step where the twin boundary terminates at the faceted growth interface. D) These three conditions are necessary, but in certain cases not sufficient for continued crystal growth with the aid of a twin plane. Depending on interface morphology, a combination of more twin planes is sometimes required to form a self-perpetuating system of nucleation sites. This investigation was carried out with the idea in mind that nucleation with the aid of twin planes is a more general phenomenon and should occur in those materials, grown from a supercooled melt, which satisfy the criteria outlined above. It has been found that crystals of high-purity bismuth grown from a supercooled melt can grow by the aid of a twin plane. In the first two sections the faceted growth form and the twinning elements of bismuth are discussed. In the last section prismatic crystals of bismuth, which appear to grow with the aid of a deformation twin are discussed.

Jan 1, 1962

By Alexander L. Holley

THE Pernot system of rotating and withdrawing the hearth of a Siemens regenerative gas furnace for the production of Martin or open-hearth steel, is, perhaps, the most conspicuous of the several improvements which have lately been made in the steel manufacture. These several improvements in the open-hearth plant are not combined in any existing works, but most of them will be combined in not less than three works now erecting in the United States; and it seems probable that their joint result will not only reduce the cost of products of ordinary grades to Bessemer rates, but that it will produce new and better grades of products. The open-hearth steel furnace and its operation are so generally understood that but a few words of general description are necessary. The ordinary furnace is not unlike the common reverberatory puddling furnace, except that an intense, uniform, and controllable temperature is maintained by the Siemens gas regenerative system. The materials. employed are various : melted or unmelted pig with ore, and with or without scrap; pig iron purified from silicon and phosphorus, with or without scrap; pig iron and scrap, melted together in a cupola, or charged hot or cold, together or separately, into the steel furnace; a pig-iron bath, and hot or cold steel or iron scrap, direct sponge or Catalan or puddled blooms charged into the bath. The operation is, to a greater or less extent, according to the nature of the materials used, a desiliconization and decarburization of the pig or other crude iron, and its dilution by already purified materials. Manganese is employed at the end of the operation to remove oxide of iron and silica, a regulated amount of manganese remaining in the product. Figs. 2 and 3, Plate IV, represent the hearth and roof of the Pernot furnace; Fig. 1 shows, in cross section, the general arrangeent of open-hearth plant with Pernot furnaces, as generally designed by the author, and now building at two works. The engrav-

Jan 1, 1879

Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state. In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.

Jan 1, 1925

By L. Massé, Th. Koulomzine

Note on Haalck's Formula Quantitative interpretation of magnetic anomalies is admittedly a difficult process. Few authors have attempted a general approach to this problem. A number of publications can be found widely scattered through scientific periodicals, which present particular solutions obtained by the introduction of simplifying assumptions, such as the reduction to an equivalent magnet or pole, or the hypothesis of a very thin vein. The practical applications of these solutions are necessarily very restricted though they have given satisfactory results in isolated cases. Probably the most widely known equation of this type was given by Haalck.' His classic work contains curves calculated for typical conditions, and has now become a standard reference. However, a close scrutiny of Haalck's derivation reveals that, aside from the hypothesis of a thin vein, it rests on the

Jan 1, 1949

By R. J. Charles, G. Agar

Experiments on single particles show that the amount of material created during impact that is finer than any chosen size is proportional to the energy of the impact. As the underlying principle of comminution, it might be stated that each unit of energy input to a given comminution system tends to add to the system an identical assembly of new particles and subtract an equivalent volume of larger particles. Thus, two of the consequences of the fact that each unit of energy tends to add identical assemblies of new particles to the system are: 1) on continued application of energy the total charge in any batch comminution system tends to assume the characteristics of this assembly, and 2) the process of comminution may be described by a relationship such as E = Ak-a. Recently Schuhmannl presented a theory of comminution which puts rational perspective on the extensive controversy surrounding most of the existent theories of comminution. With hindsight the origin of controversy can be ascribed to a relatively simple circumstance. In general, a progressive shift of a size distribution curve towards finer sizes is observed as energy is added to a comminution system. It is also observed that, with continued grinding, the size distribution curves usually change and appear to approach some constant shape. Inves-tigators generally felt that an appropriate method of relating and generalizing such data would be to consider the hypothetical case where particles in the system were uniformly subjected to comminution such that each of these particles, receiving its proportion of input energy, was transformed into a number of smaller particles of uniform size. Since the changes in shape of the size distribution curves during size reduction were clearly associated with the coarse particles in the system, it was also assumed that these changes accounted for little of the input energy and one could deal solely with the equilibrium shape towards which the size distribution curves tended. Although the unrealistic nature of the foregoing points of view was realized some justification was felt for such treatments since, in most cases, the resulting mathematical formulae could, by the adjustment of at most two parameters, satisfactorily describe experimental observation. Difficulties arose, however, in that the formulae required a specific influence of the feed size on the comminution process. In actual fact, the application of a feed size term in fitting experimental data was often found to be unnecessary or contrary to the above formulae. Secondarily, much discussion arose concerning the appropriate energy number that would relate the size change of one particle to the amount of comminution energy it received. As has been previously shown3 all the above theories that treat comminution as a continuous process of size reduction may be related to a proposition of the following form: dE = -Cfn [1] where dE is the increment of energy, dx is the size change, x is the particle size, and C and n are constants. It is now clear, as pointed out by Schuhmann, that Eq. 1 is inapplicable to comminution processes, since comminution cannot be considered other than as a discontinuous mixing process in which the overall size distribution of the product results from mixing, in various proportions, finished material with unfinished, and sometimes untouched, material. A striking illustration of this mixing phenomena may be obtained by comparing the size distributions of grinds in a typical batch ball mill with size distributions calculated on the basis of mixing various proportions of feed material with a ground material which obeys a power law size distribution relationship. Figs. la and lb illustrate such a comparison and the similarity of these figures indicates that mixing plays an important role in determining the overall shape of the product size distributions. Figs. la and lb illustrate, additionally, the underlying basis of the comminution theory presented by Schuhmann.' In the preliminary grinding of relatively close sized feed particles in a batch ball mill, one may visualize that, when a successful encounter of a ball with a feed particle occurs, then the particle undergoes severe size reduction and the size range in which the resultant particles reside is far removed from the size of the feed particles. After a number of feed particles are reduced by independent but similar impacts and one examines the size dis-

Jan 1, 1961

By C. D. Ramsden

During the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Purchase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by salvaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a considerable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been rebuilding locomotive wheels for several years with automatic open are-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under-flux are-welding process for wheel rebuilding, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. Open Arc Welding With the open arc process, a set of wheels could be rebuilt for about 40 pet of the cost' of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or positioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1947

By C. D. Ramsden

During the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Purchase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by salvaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a considerable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been rebuilding locomotive wheels for several years with automatic open are-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under-flux are-welding process for wheel rebuilding, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. Open Arc Welding With the open arc process, a set of wheels could be rebuilt for about 40 pet of the cost' of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or positioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1947

By José Aloisio Paione, Eudes Prado Lopes

The geophysical exploration carried out by the Brazilian government through the Mineral Resources Development Co. (CPRM) to discover and develop Brazil's mineral resources is discussed. Particular mention is made of procedures specially adapted for contracting companies specialized in geophysics, CPRM's activities, statistical data from study programs, as well as the financial investments committed. More than 500 000 km of aerogeophysical surveys have been carried out by CPRM in the last four years, and it is expected that more than 600 000 km will be flown in 1974 and 1975, at an investment of approximately $30 million.

Jan 1, 1977

By Frank H. Skelding

Still the world's largest producer, consumer and importer/exporter of minerals, the United States has, in recent years, become more and more aware of the many diverse forces that increasingly affect its ability to maintain free access to and trade in minerals, both domestically and abroad. The nation's growing dependence upon foreign sources of minerals in the face of mounting competition is causing many changes, not only in the mineral industries, but in national attitudes and policies as well. This paper examines the position of the United States in the world mineral economy relative to the significant trends that have and are developing. It attempts to define and evaluate the major present and future impact of these trends and to anticipate the probable effects upon the U.S. and its mineral economy.

Jan 1, 1976

By Dorsey A. Lyon, Robert M. Keeney

The electric furnace has always been found to be especially adapted to melting, refining, and finishing processes throughout its gradual acceptance by metallurgists as a practical apparatus for conducting metallurgical operations. In the steel industry, the electric furnace is firmly established in the manufacture of steel of the highest grade, equal to crucible steel. For the production of the cheaper grades of steel in large tonnage, the electric furnace gives a higher-grade product than the open-hearth or converter, but due to the high cost of power prevailing in steel centers, considered from the electric furnace standpoint, it is not economical to produce tonnage steel in the electric furnace. As a refining and finishing agent for open-hearth or Bessemer steel, the electric furnace has had some degree of success in thc production of tonnage steel. After a study of the use of the electric furnace in the steel industry, it appears that there may be a possibility of its use to advantage for the melting of cathode copper. In the case of copper the problem is not one of actual refining, because the copper if refined properly by the electrolytic method needs no further refining; it needs simply to be cast into a marketable shape. The name "refining" is applied to the present finishing process, because in the operation oxygen and other impurities arc removed, which the electrolytic copper absorbs in being melted in the reverberatory furnace. Considering that processes may be positive, negative, and neutral, the electrolytic method would be positive; reverberatory melting of cathode copper, negative; and electric furnace melting, neutral. The electrolytic method produces about as pure a copper as is possible, if operated properly and the anodes are not too impure. The final reverberatory melting of this cathode copper lowers the grade of the final product, due to the absorption of gases and impurities. The reverberatory melting of cathode copper is one of the weak parts

Jan 1, 1915

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922