Search Documents

By William Fink

ALTHOUGH age-hardening in an aluminum-base alloy containing magnesium was observed by Alfred Wilm1 as early as 1911, it was not until 1919 that a theory of the mechanism of age-hardening was proposed. Merica, Waltenberg and Scott,2 studying the age-hardening character-istics of Duralumin at the National Bureau of Standards, came to the conclusion that age-hardening of this alloy is caused by the precipitation of CuAl2, which is less soluble at the aging temperature than at the solu¬tion heat-treating temperature. It was postulated that the initially precipitated particles were of fine colloidal dimensions but that they gradually grew in size. Maximum hardness was assumed to be attained when the particles reached a critical size. This theory was at first received skeptically, since it was a widely accepted view at that time that the solid solution state should represent the hardest state of an alloy. Shortly thereafter, Jeffries and Archer proposed their well-known "slip interference theory."3 They suggested that age-hardening was accomplished by the precipitated particles acting as keys interfering with slip along crystallographic glide planes. They showed that this mechanical theory led directly to the assumption that maximum harden-ing would be produced by particles of a critical size, which they suggested would have a diameter approximately 10 times that of the aluminum atom. This contribution amplified and explained so rationally the age-hardening theory of Merica, Waltenberg and Scott that wide accept-ance resulted.

Jan 1, 1939

By P. B. Bucky

THE purpose of this paper is to present a scientific method for deter-mining the proper span and shape of roof for safe and economical mining; at present, these two vital factors wherever pillars are left to support the roof are determined by local practice or general experience. To develop the method described here, experimental laboratory work was done. The arch adopted was a segment of a circle, a flat roof being considered an arch with an infinite radius. Hitherto, arches have been used underground without the background of stress analysis that generally precedes arch construction on the surface. In many cases results have not been as expected, because of the lack of knowledge of the factors affecting its strength and behavior. A theoretical and experimental study of arches should furnish informa-tion that will make it possible to design safe and economical surface structures as well as underground openings. For example, on the subject of mine drifts and tunnels, the present idea is that arching their backs increases their strength; this paper will indicate that this is not always true, and if it can be shown that under certain conditions arching becomes unnecessary an economic saving will result. In room-and-pillar work a question may arise as to whether arching the roof and gobbing the excavated material will result in timber saving, and a decrease in the dan¬gers from falls of roof. It is to be distinctly understood that each mine must be treated as an individual problem, and that answers to these ques-tions and many others can now be found after experimental laboratory data have been obtained.

Jan 1, 1934

GEORGE F. BECKER Dr. George Ferdinand Becker, notice of- whose death appeared in the May Bulletin, was born in New York City Jan. 5, 1847, the son of Alexander Christian Becker, member of a Danish family, and Sarah Cary Tuckernian Becker of Boston. Dr. Becker was the last member of the group of distinguished geologists who, in 1879, were associated with Clarence King at the time of the organization of the United States Geological Survey. He was a leader in mining geology and geophysics, and for many years had been the chief of the Division of Chemical and Physical Research in the Geological Survey, and the investigations under his direction led to the establishment of the Geophysical Laboratory of the Carnegie Institution of Washington. Dr. Becker was a graduate of Harvard University and received the degree of Doctor of Philosophy at Heidelberg, and in 1871 passed the final examinations at the Royal School of Mines in Berlin. He was for four years an instructor of mining and metallurgy in the University of California, from which he went to the United States Geological Survey. In 1896 he examined the gold and diamond mines f South Africa and at the time of the Spanish-American War was detailed to serve as geologist on the staff of General Bell with the army in the Philippine Islands. He died at his hone in Washington, D. C., on Apr. 20'.1

Jan 6, 1919

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC and was installed on a shuttle car in a conventional room-and-pillar mining section. The purpose of the study was to evaluate proposed legislation that would require shielding on low-voltage trailing cables. Such legislation would require machine modifications to cable reels, packing glands, and couplers; increase cable splicing complexity; and necessitate additional splicing materials and training. Furthermore, fault location might be more difficult. Even though shielding will cause some problems for the mine operator, it can reduce electrical shock hazard to mine workers. This paper presents information that mine operators can use to solve most of the problems encountered if they are required to install shielded cables. The in-mine evaluation was funded by the US Bureau of Mines; however, the views and conclusions in this paper are those of the author and should not be interpreted as necessarily representing official policies of the US government.

Jan 1, 1982

By John McDonald

THE amount of published literature in the field of mechanical proper-ties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherch1 have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing' with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in, properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the proper-ties of alloys in conditions where the effect of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these proper-ties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments will produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of working and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treat-ments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloys have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are relatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1939

ON THIS page is a photograph of a machine that has played a key role in the recent history of Kennecott's Ray mine, situated in the Mineral Creek District, Pinal County, Arizona. It is a huge, rugged, Diesel-powered, rubber-tired truck, having a capacity for carrying fifty tons of ore. It has, to a substantial degree, revolutionized the business of moving broken rock by cutting down both maintenance and operating costs. From 1911 until the end of 1954 Ray had produced 79,000,- 000 tons of ore by underground block-caving. However, in 1947 [ ]

Jan 1, 1957

By S. E. Piper, E. M. Buchalter, R. P. King, E. T. Woodburn

The problems involved in an optimum decision making model for flotation circuit are, first of all, to characterize the feed material in terms of parameters which can quantitatively describe the network flotation action in terms of a feasible set of control actions. Once the characterization has been postulated, it is then necessary to devise tests relating to parameter sensitivity, in order that credibility of the model predictions can be assessed. Once a credible model is available, the optimum control set is determined by a hill climbing technique. Details will be reported as to the credibility of model predictions using the stochastic flotation model on a network and further, computational problems associated with hill climbing for a complex objective function are reviewed. Discussion is presented on use of the Rosenbrock technique with constraints and use of a modified objective function with constrained derivatives when employing Fletcher and Powell technique.

Jan 1, 1969

By G. Koves

The behavior of case-hardened AISI C-1213 free -machining steel under complex impact-fatigue -wear load conditions was investigated. The inherently poor dynamic properties of the steel are mainly affected by the stress distribution in the case, component shape, and tempering. Cold-riveted components showed unexpectedly high dynamic strength compared to basic parts. A compromise beatment—which provides good dynamic properties, reasonable wear resistance, and fair riveting characteristics—zuas developed. A number of mechanical components in data-processing machines are made of free-machining carbon steel. Although, selected primarily due to manufacturing requirements, components made of these grades frequently undergo complex heat treatment and must sustain impact-fatigue loads. A typical free-machining steel is the AISI C-1213 grade, which is a resulfurized and rephosphorized open-hearth steel. While the undesirable effects of sulfur and phosphorus on the mechanical properties are well-known, data on dynamic properties are scarce.1"3 Rapid rotating or oscillating motion while carry- ing a high cyclic load requires a combination of wear resistance with high endurance limit and impact toughness. The inherently poor dynamic properties of the free-machining steel are further degraded by the machining, which introduces local stress-concentration areas. While the heat treatment (usually case hardening) improves some mechanical properties, it necessarily impairs others. Another problem arises when components, such as studs, must be fastened by riveting. The high crack-sensitivity of the free-machining steel, especially in the presence of a hardened case, makes this operation difficult. In view of the preceding considerations, it is of interest to investigate the behavior of a typical component under complex impact-fatigue-wear loading conditions in order to explore the effects of material, machining, and heat treatment, to obtain specific data on the dynamic characteristics of free-machining steel, and to arrive at a process which would adequately utilize the inherent qualities of this material. EXPERIMENTAL PROCEDURE To simulate actual service conditions, a typical component was selected, based on frequency of application, complexity of load, and processing difficulties. The dimensions and shape of the component—a stud used in many electromechanical document-handling machines—are shown in Fig. 1.

Jan 1, 1964

By H. F. Yancey, O. L. Furse

Although usually coal is screened with punched plate screens having round-hole perforations, there has been an increasing use of wire-cloth screens with square apertures, especially at pneumatic coal-cleaning plants and at other plants that use vibrating screens. It is therefore desirable to establish a relationship between round-hole and square-hole screens for use not only in experimental investigations of coal-preparation problems, but also for use in commercial operations. This need is apparent whenever it is necessary to substitute wire cloth for punched plate and still retain the familiar trade-size product. Although similar work probably has been done by industrial organizations concerned with the screen sizing of coal, the only recorded study of the subject other than the one described herein of which the authors are aware is that of Roesler,1 who screen-sized two samples of limestone and two of zinc concentrates crushed to pass 1/2 in. with a set of square and round-hole screens and found the ratio to be 1:1.23. Procedure In the course of a study of various methods for determining the friability of coal,2 it was necessary to screen-size the products of a series of friability tests of three different coals with both round-hole and square-hole screens. The coals used were from the Roslyn No. 3 and the Bayne mines in Washington and the Rolapp mine in Utah. Twenty 25-lb. samples of each of these three coals at 3 to 2 1/2 in. round-hole size were dropped from a height of 10 ft. to a concrete floor, and then screened with

Jan 1, 1934

By R. E. Cook

This work presents the development and application of equations of the form developed by Martin1 to describe gravity segregation performance during natural depletion. One-dimensional depletion analyses are applied to several hypothetical reservoirs. Considerable attention is given to the changes in saturation distribution in the dip direction resulting from depletion at various rates. Vertical gas saturation distribution within a sand having vertical permeability is studied to illustrate conditions which provide For low gus-oil ratio production from wells selectively completed away from sand tops, as observed from well performance. Results of performance calculations are shown graphically and illustrate the rate sensitivity of the gravity segregation mechanism and the influence of reservoir geometry and withdrawal distribution. It is shown that for sufficiently high depletion rates gas saturation distribution in the dip direction is characterized by the formation of two discontinuities, or saturation "fronts"; the updip front being the gas-oil contact of the secondary gas cap and the downdip front occurring at a position dependent upon the reservoir depletion rate, withdrawal distribution and reservoir geometry. The gas saturation in the region between fronts is shown to continually increase with time, while that downdip from the lower front remains very low and relatively stable. The effect of increased depletion rate is to reduce the region of stable gas saturation and thus enlarge the portion of the reservoir producing with continually increasing gas saturation. Special attention is given to the performance of reservoirs having sufficient vertical permeability to permit liberated gas to segregate vertically within the sand section before proceeding in the updip direction. It is shown that reservoirs of this type are far less sensitive to depletion rate due to the mechanical control of producing gas-oil ratios afforded by selective well completions away from sand tops. It is shown that gravity segregation performance is adversely af- fected by decreasing reservoir cross-section area in the updip direction. It is also shown that down-dip withdrawal concentrations can restrict gas segregation rates in the dip direction. INTRODUCTION The natural depletion performance of several large producing reservoirs in Western Venezuela has unmistakably shown the significant role that gravity forces play in governing the gas-oil ratio behavior of individual wells and the over - all pressure-production performance of the reservoirs. Analysis and prediction of the natural depletion performance of these reservoirs is of great importance in determining the economics of pressure maintenance operations. In 1957, a method for the analysis of pressure maintenance performance was presented by Martin1 which, in the original and more general form of the equations involved, provides a physically sound basis for the analysis of one-dimensional gravity segregation performance during natural depletion. The work reported herein is an application and extension of Martin's outstanding developments to a series of hypothetical reservoirs in an attempt to explain the general behavior of the gravity segregation mechanism and the influence of such parameters as depletion rate, reservoir geometry and withdrawal distribution. The study considers two types of flow: "distributed flow", where vertical permeability in the reservoir is zero and fluids flow only in the dip direction while uniformly distributed over the sand thickness; and "segregated flow", where vertical permeability is sufficient to permit gas to segregate against the sand top before proceeding updip. This latter type of flow has been recognized as an important mechanism active in the massive sand reservoirs of Western Venezuela. ANALYSIS OF ONE-DIMENSIONAL DISTRIBUTED FLOW SYSTEMS For an inclined reservoir having zero vertical permeability, the velocities of oil and gas flow at any point in the reservoir can be derived from Darcy's equations as

By J. B. Ackerman, J. D. Miller

Alunite [KA13(S04)2(OH)6] is a promising non-bauxitic aluminum resource, the domestic reserves of which are estimated to be 800 x 106 tons at 35 percent alunite. The major gangue mineral associated with alunite is quartz. The thermochemical process that has been developed for treatment of this ore does not provide for the initial removal of gangue prior to processing. In this regard, it may be desirable to concentrate the ore to gain significant technical and economic advantages. Experimental results indicate the effectiveness of an oleic acid flotation technique and exemplify the problems encountered in fine particles processing. These results show that the quality of separation studied as a function of temperature, collector addition, and depressant addition is dependent on the degree of liberation achieved during size reduction. At coarse grinds the quality of separation was limited by the presence of locked particles while for finer grinds where more extensive liberation is achieved, better separations were obtained. The degree of liberation for each size interval was determined by an SEM/energy dispersive x-ray technique and found to be independent of the extent of size reduction, suggesting that liberation occurs by indiscriminate fracture and not by detachment. Up to 89 percent liberation was realized for a minus 400 mesh grind. Under these circumstances, the quality of separation appears not only to be limited by the remaining locked particles, but, also, by contamination of the alunite concentrate with fine quartz gangue (< 2µm). The best separation for the minus 400 mesh grind was a rougher recovery of 88 percent with a grade of 65% alunite at 50°C.

Jan 1, 1980

By Zay Jeffries

In this paper, it is proposed to outline a method for the determination of melting points of those metals and alloys having high fusion temperatures. The application of the method as used to determine the melting points of alloys of tungsten and molybdenum will be given. It will be seen from these results that tungsten and molybdenum form a completely isomorphous series. This is also verified by the accompanying photomicrographs. Tungsten and molybdenum have been found to crystallize in the same system namely, isometric, and the crystal units are cubes. These determinations were made by examining etching pits in the pure metals.

Jan 1, 1917

By C. A. Fisher

THE advent of the Rocky Mountain States into prominence as an oil-producing region is comparatively recent. Scarcely more than a decade has passed since the number of producing oilfields in this part of the country were few and their combined yield small and relatively unimportant. However, oil was discovered and recorded near the present site of Lander, Wyo., as early as 1833 and in 1867, on the comple-tion of the Union Pacific R. R., the site of this oil discovery was located, among other things, as a natural resource of economic importance. In that year a well was drilled for oil, to a depth of 480 ft., near Evanston, Wyo., but later was abandoned. In 1883, the Lander district witnessed the successful completion of the first oil well in the state. In Colorado, oil was first produced from shallow open wells near Canon City and sold to prospectors in 1864; in 1887, the Florence oilfield was discovered and a commercial production developed. While the Rocky Mountain States have never gained the prominence as an oil-producing region attained by the Pacific Coast, Mid-Continent, or Gulf fields, a substantial and increasing production is being taken from the Rocky Mountain province. At the close of 1923, the oil industry in this region has 38 oil and 21 gas fields producing, or capable of producing, oil or gas in a commercial way with a combined annual yield of nearly 47,000,000 bbl. of oil, a daily refining capacity aggregating about 90,000 bbl., upwards of 17,000,000 bbl. of crude in storage, and an 8-in. pipeline, nearing completion, 600 miles long which will connect the most prolific oilfield of the Rocky Mountain States with a trunk pipeline between Mid-Continent and the east at Carrollton, Mo. Several of the larger standard and independent operating companies are now represented in this region and, in the last ten years, there has been developed at Casper one of the large refining centers of the west. Fig. 1 illustrates the rise in production of four of the larger fields, also in the total production of the state; in addition there is given the yield of the larger fields of Wyoming and Montana for 1923.

Jan 3, 1924

By George S. Ansell, Thomas E. Davidson

It has been known for a considerable period of time that the ductility of even quite brittle materials can be enhanced if they are deformed under a superposed hydrostatic pressure of sufficient magnitude. The response of ductility to pressure, however, has been shown to vary considerably between materials. Prior work has shown that the effects of pressure upon the tensile ductility of Fe-C materials depend upon the amount, shape and distribution of the brittle cementite phase. In this current investigation, the effects of pressure upon the fracture mechanisms in a series of annealed and spheroidized Fe-C materials were examined. It was observed that the principal effect of pressure is to suppress void growth and coalescence, retard cleavage fracture and to enhance the ductility of cementite platelets in pearlite. Based upon the observed effects of pressure upon the fracture mechanisms, a proposed explanation for the enhancement in ductility by pressure and for the structure sensitivity of the phenomena is presented and discussed. THE effect of superposed pressure upon the tensile ductility of a variety of metals has been well documented.&apos;-&apos;&apos; Some of the results from several investigators are summarized in Fig. 1 where tensile ductility in terms of true strain to fracture (ef) is plotted as a function of the superposed pressure. As can be seen, a pressure of sufficient magnitude can significantly enhance the ductility of metals. However, Fig. 1 also demonstrates that the response of ductility to pressure and the form of the ductility-pressure relationship varies considerably between materials. Several explanations have been offered for the observed enhancement in ductility by a superposed pressure. Although no experimental evidence was provided, Bridgman13 and Bobrowsky10 proposed that the observed effect was due to the prevention or healing of microcracks or holes. Bulychev et a1.14 observed that cracks and voids in initially prestrained copper were healed in the necked region of a tensile specimen upon further straining while under a superposed pressure. Also, pugh5 observed that large cavities were suppressed in copper fractured in tension while under pressure. A second proposal has been forwarded by Beresnev et at al.6 This proposal is based upon the hypothesis that a material fails in a brittle manner because the normal tensile stress reaches a critical value before the shear stress is of sufficient magnitude to cause plastic flow. Since a superposed hydrostatic pressure will increase the ratio of shear to normal tensile stress, a sufficiently high hydrostatic pressure should favor plastic flow while retarding brittle fracture. Galli15 reported that a superposed pressure shifts the ductile-brittle transition temperature of molybdenum. This was explained based upon the reduction of the normal tensile stress by the superposed pressure. Pugh5 explained the occurrence of the observed pressure induced brittle-to-ductile transition in zinc in the same manner. Davidson et al.12 proposed an explanation for the enhancement of ductility by pressure based upon the effects of pressure upon the stress-state-sensitive stages of various fracture propagation mechanisms. Basically, they proposed that pressure will retard cleavage and intergranular fracture by counteracting the required normal tensile stress or will suppress void growth. They observed suppression of intergranular fracture and void growth in magnesium by pressure. Davidson and .Ansell16 reported ductility as a function of pressure for a series of annealed and spheroidized Fe-C alloys. Fig. 2, from this prior work, demonstrates that the effect of pressure upon ductility is structure sensitive in terms of the amount, shape and distribution of the brittle cementite phase. As shown in Fig. 2, in the absence of cementite or when the cementite is in isolated particle form (spheroidized), the ductility-pressure relationship is linear and the slope decreases with increasing carbon content. In the annealed carbon-bearing alloys wherein the cementite is in the form of closely spaced platelets (pearlite) or in the form of a continuous network along prior aus-tenite boundaries (1.1 pct C material), ductility as a function of pressure is nonlinear (polynomial relationship) in which the slope increases with increasing pressure. At the highest pressures studied (22.8 kbars), the slope of the curves for these materials tends to approach those for the spheroidized material of the same carbon content. In this current investigation the change in fracture mechanisms as a function of pressure for the materials shown in Fig. 2 has been examined. The possible connection between the observed effects of pressure upon the fracture mechanisms and the effect of pressure upon ductility is discussed.

Jan 1, 1970

By Thomas A. Simpson, Russell A. Walker

Hydrogeological techniques were used to solve problems of slope stability in open-pit mines of the Eufaula bauxite district, Ala. Geologic and hydrologic data were evaluated and used to design a system of dewatering wells to enable the operators to mine bauxite more efficiently and economically. Walls of open-pit mines in the district were subsequently stabilized by the operation of the dewatering system. Three open- pit mines, each at varying stages of the mining process, of the A.P. Green Refractories Co., were used to develop a sequential series of guidelines that indicate how to effectively remove ground water from the formations surrounding the ore bodies in the district. The use of sound engineering principles in well design, in combination with the correct interpretation of the pit hydrology provided the basis for solutions of the slope-stabilization problem and aided in the economical removal of bauxite from mines of the district.

Jan 1, 1976

By William Glenn

The Ritchie grahamite-mines of Ritchie county, West Virginia, were situated near the central part of the upper barren coal-measures

Jan 1, 1895

By E. P. Pfleider, W. D. Lacabanne

ROTARY-percussive drilling is a new method of drilling hard rock. Designed to give variations in thrust, revolutions per minute, and torque ranges, these drills combine the high efficiency of the rotary system in soft rocks with an increasing amount of percussive action in rocks more difficult to fragment. Fundamentals of the rotary, percussive, and combination systems have been described in detail in various papers-most recently by C. Fairhurst and W. D. Lacabanne1-but there is still much basic work to be done on the interplay of actions in the rotary-percussive system to enable the drill designer to achieve the highest efficiencies. Whereas the original units struck light blows of only 15 to 30 ft-lb, adequate for medium hard rocks, the present trend is to piston blows of 50 to 65 ft-lb in order to cope with the granites and other rocks having Shore hardnesses of 75 or more.

Jan 7, 1957

By Massimo Guarascio

Computer data processing and ore reserve evaluation techniques, mainly based on geostatistical methodologies, have been developed at Agip Mining Division with the assistance of the Department of Mining Engineering of the University of Rome. A number of computer programs are available when facing problems such as optimization of sampling patterns, minable reserve estimation, grade control of output, and so on. In the present paper, the aims and the criteria followed in developing these programs are discussed. Some recent examples of application are also cited.

Jan 1, 1977

By Rodney Lawrence, Tim Hackett

INTRODUCTION The western USA contains significant coal reserves in seams 10 feet or more in thickness which lie too deep for surface mining. As part of a demonstration of the use of two legged shield supports in the United States, Kaiser Steel Corporation, under contract to the US government used the longwall method to mine a ten foot thick coal seam in New Mexico. Caliper type shield supports and double drum shearers were used in three longwall panels. During the test, technical, production, and safety data were collected to objectively evaluate the performance of the shields in mining the thick coal seam. This paper presents discussions of practical operating experience and summary statistics to aid the mining industry in planning longwall mines in similar conditions.

Jan 1, 1981