Search Documents

By H. C. Chang, N. J. Grant

Creep of very coarse grained high purity aluminum was studied at 400°, 700°, and 1100°F at initial stresses of 50 to 1200 psi. Local strain measurements were made across the grain boundaries and in different regions of various grains during creep, thereby permitting the drawing of component creep curves. The relative amounts of elongation as measured across a grain boundary and in the grains adjacent to the boundary depend on the temperature of testing. The significance of creep curve equations and activation energies is discussed. THIS paper presents some of the results of a research program devoted to the study of the mechanism of creep in high purity aluminum. Previous publications have dealt with the cyclic processes of alternating grain boundary sliding and migration, and the deformation in the grains caused by these processes;' the direction and the driving force of grain boundary sliding and migration;' the deformation in the grains and the restricting effects of the grain boundaries on this deformation." These previous papers were based mainly on either microscopic observations or X-ray data, or both. Sometimes creep curves across two closely spaced reference marks (about 0.6 to 0.7 mm apart) were also presented with a view to correlating the elongation values with the optical observations in general, and with certain deformation processes in particular. These curves shall henceforth be referred to as component creep curves. No attempts were made, however, to compare either the component creep curves which were obtained in different regions of a specimen, or those obtained from different specimens subjected to different creep test conditions. It is the purpose of this paper to present these component creep curves. Among the factors influencing the behaviors of these curves, those studied were stress, temperature, and grain arrangements in the specimens. It is proposed to show how greatly the deformation can vary from grain to grain and within an individual grain in a coarse grained specimen. The experimental technique and procedure have been presented.' It remains necessary to emphasize that the reference marks were produced by pressing a thin sewing needle into the surface of the specimen before the final annealing at 900°F for 24 hr and at 1150°F for 12 hr. The cold work around the needle indentations was therefore removed. The depth of these holes after electropolishing the annealed specimens was about 0.01 mm. This depth and area were negligible in comparison with the thickness of the specimens, 2.3 mm, and hence would not affect the creep behavior. Results Fig. 1 shows a development diagram of specimen P-8. The dots on the surface locate the needle point reference marks used to obtain the component creep curves. A curve obtained between two dots across a grain boundary measures not only the boundary deformation but also the deformation associated with boundary sliding occurring in the grains in the region between these indents. The original distance between two reference marks was about 0.6 to 0.7 mm. The maximum error of measurement was 0.01 mm, or in terms of percentage elongation, of the order of & 1.5 pct. Whereas the component creep curves shown in the figures to follow were drawn as a gross average of the points, in view of the fineness of some of the steps of grain boundary sliding and migration, as shown in the previous publications,¹,2 it appears logical to expect that some of the finer cycles of movement have not been delineated for the strain sensitivity of the measuring system. It seems justifiable to say that the curves are not as smooth as shown. 700°F Tests: Fig. 2 shows component creep curves across four of the grain boundaries in specimen P-8, tested at 700°F and 85 psi. These curves clearly show alternate cycles of increasing and decreasing

Jan 1, 1954

By Edgar Stansfield

ONE of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal.

Jan 1, 1932

By R. J. Schilthuis

In 1929, Coleman, Wilde, and Moore1 undertook an investigation of the theoretical decline in reservoir pressure as related to the production of oil and gas. The most important part of this work was presented in an equation defining the relationship between the reservoir pressure, the quantities of oil and gas produced, the oil and gas content of the reservoir, and the properties of the reservoir fluids. With this equation, it appeared that, with sufficient data, it would be possible to calculate the oil content of the reservoir and predict quantitatively the effect of gas-oil ratio on the decline of reservoir pressure. Needless to say, such an expression would be highly important in evaluating fields and in arriving at a choice of production methods to be used. Unfortunately, at the time these investigators published their work, there were not sufficient data available to permit application of the equation. The technique of measuring reservoir pressures had not been developed, gas measurements were uncommon, oil and water production records were in most cases inadequate, and little was known of the properties of the complex hydrocarbon mixtures making up the oil and gas in the reservoirs. For these reasons, little additional work of a similar nature could be done. However, during the past four years many data have been systematically accumulated on reservoir pressures and the properties of oil and gas, and it is now possible to use these data in furthering the studies on the behavior of oil and gas reservoirs. It is the purpose here: first, to present the derivation of a modified form of the equation given by Coleman, Wilde and Moore, which will permit the calculation of what later will be defined as the "active oil" content of a reservoir; second, to derive formulas for calculating the reservoir-energy changes that occur during the course of production, and finally, to discuss the limitations and application of the equations developed.

Jan 1, 1936

By R. J. Schilthuis

In 1929, Coleman, Wilde, and Moore1 undertook an investigation of the theoretical decline in reservoir pressure as related to the production of oil and gas. The most important part of this work was presented in an equation defining the relationship between the reservoir pressure, the quantities of oil and gas produced, the oil and gas content of the reservoir, and the properties of the reservoir fluids. With this equation, it appeared that, with sufficient data, it would be possible to calculate the oil content of the reservoir and predict quantitatively the effect of gas-oil ratio on the decline of reservoir pressure. Needless to say, such an expression would be highly important in evaluating fields and in arriving at a choice of production methods to be used. Unfortunately, at the time these investigators published their work, there were not sufficient data available to permit application of the equation. The technique of measuring reservoir pressures had not been developed, gas measurements were uncommon, oil and water production records were in most cases inadequate, and little was known of the properties of the complex hydrocarbon mixtures making up the oil and gas in the reservoirs. For these reasons, little additional work of a similar nature could be done. However, during the past four years many data have been systematically accumulated on reservoir pressures and the properties of oil and gas, and it is now possible to use these data in furthering the studies on the behavior of oil and gas reservoirs. It is the purpose here: first, to present the derivation of a modified form of the equation given by Coleman, Wilde and Moore, which will permit the calculation of what later will be defined as the "active oil" content of a reservoir; second, to derive formulas for calculating the reservoir-energy changes that occur during the course of production, and finally, to discuss the limitations and application of the equations developed.

Jan 1, 1936

By H. F. Yancey

COAL mine operators recognize coal as an abrasive material, because the wear of drilling, cutting, and conveying equipment is reflected as a cost item for replacement of parts. Similarly, industrial consumers of coal experience abrasive wear on all coal-handling equipment. Operators of pulverized fuel plants are doubtless most keenly aware of the abrasiveness of coal, because under the high contact pressures developed between coal and metal in pulverizers, abrasive wear is increased many fold. Moreover, experience in operating pulverized fuel plants has demonstrated that some coals are much more abrasive than others.

Jan 3, 1951

By W. M. Weigel

THE rapid advance, during recent years, in the manufacture of articles that have been in common use for generations and the development of new materials entering into appliances and devices unheard of fifty years ago, have created a demand for some of the more common non-metallic minerals. To supply this demand there has quietly developed a branch of the mining industry of which little is known by most mining engineers the mineral-filler industry. In this paper, and generally in the trade, the term mineral filler is applied to a mineral used, in its natural state after mechanical preparation only (such as. grinding, milling and washing), without undergoing any chemical change and without exerting any chemical action on the substance with which it is incorporated. The consumption of mineral fillers is confined chiefly to large manufacturing centers in the eastern and northern states. Where available, materials originating near the place of consumption are used, as most fillers bring a comparatively low price and, frequently, the freight may equal the cost of the finished filler at the mine. The southern states have abundant deposits of non-metallic minerals suitable for fillers, which supply the manufacturing industries in adjacent states. Many of these deposits are equal to, or superior, in quality to those mined in the north, but they can not compete with them because of the freight rates. The mineral-filler industry has felt the present depression, but it has suffered less than most mining industries for as a rule the mills are simple, the overhead expenses are low, and the labor is entirely local and can revert to farm work when the plant closes down. Many other deposits in the southern district will undoubtedly be developed when business. revives and freight rates are adjusted.

Jan 2, 1922

By E. C. Babson

In order to explore the possibility of predicting reservoir performance from laboratory data, behavior of a hypothetical low-permeability reservoir has been estimated by applying data and methods currently available in the literature. A method of calculating decline in productivity index is discussed, and recoveries by internal gas drive, external gas drive and water drive are estimated. Introduction During the life of a producing oil property an operator is faced with many perplexing problems. Any attempt to determine proper well spacing, optimum rate of production, or the desirability of pressure maintenance requires the evaluation not only of a host of economic and practical operating factors but also of the future performance of the reservoir. Although in some cases economic or operating con-siderations may be of primary importance in planning a development or production program, the anticipated effect on ultimate recovery is more likely to be the decisive factor. The soundest basis for evaluating reservoir performance is past experience with oil fields, but pertinent data are difficult to obtain or apply under conditions normally encountered in California fields. Many of these fields are characterized by thick sections of alternating sands and shales complicated by faulting and rapidly changing lithologic conditions. Further compli- cations are introduced by haphazard development and production practices resulting from competitive conditions, changing demand for oil, and insufficient knowledge of structural conditions during early development. Even in the rare cases where development has been systematic and adequate, production policy has usually been controlled by economic and competitive factors rather than a desire to obtain information for use in future operations. In other words, comparable reservoirs in which development and production practices have been systematically varied are seldom found. In the light of these conditions, conclusions based on experiences usually lack the certainty required for decisions involving large sums of money. Some other method of attacking these problems is needed to supplement and orient field experience. Progress in laboratory investigations of the flow of oil, gas, and water through sands has been so rapid in recent years that these data may furnish such a supplementary approach in the near future. In order to explore this possibility the author has attempted to predict the behavior of one type of reservoir by applying published data and methods. Basic Data and Assumptions Calculations outlined in this paper are dependent upon a detailed knowledge of the properties of oil, gas, and water present in the reservoir and the portion of the total pore space originally filled by each. It is also necessary to know how the permeability of the sand to oil, gas, and water varies with the saturations of these fluids 20

Jan 1, 1944

By E. C. Babson

In order to explore the possibility of predicting reservoir performance from laboratory data, behavior of a hypothetical low-permeability reservoir has been estimated by applying data and methods currently available in the literature. A method of calculating decline in productivity index is discussed, and recoveries by internal gas drive, external gas drive and water drive are estimated. Introduction During the life of a producing oil property an operator is faced with many perplexing problems. Any attempt to determine proper well spacing, optimum rate of production, or the desirability of pressure maintenance requires the evaluation not only of a host of economic and practical operating factors but also of the future performance of the reservoir. Although in some cases economic or operating con-siderations may be of primary importance in planning a development or production program, the anticipated effect on ultimate recovery is more likely to be the decisive factor. The soundest basis for evaluating reservoir performance is past experience with oil fields, but pertinent data are difficult to obtain or apply under conditions normally encountered in California fields. Many of these fields are characterized by thick sections of alternating sands and shales complicated by faulting and rapidly changing lithologic conditions. Further compli- cations are introduced by haphazard development and production practices resulting from competitive conditions, changing demand for oil, and insufficient knowledge of structural conditions during early development. Even in the rare cases where development has been systematic and adequate, production policy has usually been controlled by economic and competitive factors rather than a desire to obtain information for use in future operations. In other words, comparable reservoirs in which development and production practices have been systematically varied are seldom found. In the light of these conditions, conclusions based on experiences usually lack the certainty required for decisions involving large sums of money. Some other method of attacking these problems is needed to supplement and orient field experience. Progress in laboratory investigations of the flow of oil, gas, and water through sands has been so rapid in recent years that these data may furnish such a supplementary approach in the near future. In order to explore this possibility the author has attempted to predict the behavior of one type of reservoir by applying published data and methods. Basic Data and Assumptions Calculations outlined in this paper are dependent upon a detailed knowledge of the properties of oil, gas, and water present in the reservoir and the portion of the total pore space originally filled by each. It is also necessary to know how the permeability of the sand to oil, gas, and water varies with the saturations of these fluids 20

Jan 1, 1944

By J. E. Clennell

IT is a common observation that the improvements introduced in practice since the first announcement of the cyanide process have been almost entirely mechanical. Although a good deal of study and research has been devoted to the chemical problems involved, the results obtained appear trifling in comparison. Few of the suggested modifications in the chemical treatment have come into practical use and those only in limited fields. Nevertheless, if we study the recent history of the cyanogen compounds from a somewhat broader standpoint, we shall find that considerable additions have been made, not only to our knowledge of their chemical properties, but also to their applications for industrial purposes. The present review of these advances naturally falls into two divisions: (1) processes involved in the treatment of ores; (2) manufacture of cyanides and other related compounds. PART I. ADVANCES IN THE CHEMISTRY OF ORE TREATMENT BY CYANIDE In the attempt to extend the scope of the process, various ores have been encountered which contain gold and silver in such forms that they will not yield satisfactorily to ordinary methods of cyanide treatment. . In some cases the difficulty is due to the excessive action on the solution of base metals present in the ore; in others, to the occurrence of minerals such as dyscrasite (the native alloy of antimony and silver), or a supposed oxidized manganese compound containing silver, which are either altogether insoluble in or very slightly attacked by cyanide. A particularly troublesome case is that of the so-called "graphitic" ores, containing carbon in some form which has the property of precipitating gold and silver already dissolved.

Jan 10, 1915

By Donald R. Williamson, Edward R. Mueller

Cyprus Pima Mining Co.'s open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. Over the years, a number of attempts have been made to refine and polish the ore reserve figures using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results.

Jan 1, 1978

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951

By O. C. Ralston, F. Fraas

VIRTUALLY all commercial use of electrostatic separation has employed separators depending on differences of conductance of the broken, solid mixtures treated by them. The two main types of conductance separators have been: (1) Those in which the separating field is as near a static field between two charged electrodes as it is possible to maintain in the face of the usual leakage that takes place between electrodes with some 5 to 50 kv tension between them and spacing of 1/2 to 3 in.; (2) those in which a convective discharge of corona or spray type, but not a spark discharge, takes place between the carrier electrode and a charged electrode facing it, which is of very restricted area, such as a row of needle points or a small diameter wire parallel to the face of the carrier electrode. The present paper deals with this latter type. The principle is usable in separators where the carrier electrode, usually grounded, has the shape of a roller, a conveyor belt, a vibrating table, a sloping chute, or a nearly vertical plate. The innovation studied by us has been the use of the convective field for charging material on the carrier electrode and succeeded by a field between the carrier electrode and an electrode made of a true dielectric which cannot take on a charge by conduction but is charged by being in the radius of the corona discharge. The acquired charge is of the same sign as that of the corona but is not dischargable by contact with a good conductor. However, high-tension charge tends to leak off because of the ionization of the ambient air. The field between this electrode and the carrier electrode is as near static as it is possible to obtain. There are some differences in behavior of this electrode and that of the gas tube electrode used by Sutton, as will be discussed below. Both electrodes cause increased adhesion of nonconductive particles to the carrier roll. The particles are pinned there because they are convectively charged on their outer surfaces facing the corona electrode. The electrodes also cause increased rate of release of conductive particles tending to be pinned by corona charging but conveying the charge to the grounded carrier roll almost as rapidly as it is received by the particles. The sign of the potential on the corona-emitting electrode makes little difference in the separation. An electrode usually emits negative corona somewhat more easily than it emits positive corona, as electrons are then the fundamental particles emitted. With a positive electrode the flow of electrons involved in positive corona discharge is onto the electrode from the ambient gas. Theory In the separator illustrated in fig. 1, the nonioniz-ing electrode is a rotating, nonconductive dielectric cylinder designated as B. The ions emitted by the corona electrode, or wire F, charge both the particles on the carrier electrode, or roll A, and the surface of the dielectric electrode B. Whereas the space between roll A and wire F contains ions, the space between electrode B and roll A is a pure static field free of ions. The dielectric electrode has been described by Bullock.1 However, the corona electrode, which Bullock uses for the purpose of charging only the dielectric electrode, is adapted here to also charge the particles on the carrier roll. In operation the ionic field from the corona electrode is balanced with the static field from the dielectric electrode. The ionic field charges the particle so that it adheres to the roll. The static field intensifies the discharge of the corona charge by interfacial conduction and permits the release of the particle. The ionic and static fields therefore have opposing effects.2 The values of both fields are adjusted so that the poor conductor will adhere and the good conductor will be released.

Jan 1, 1951

By A. L. Marshall, F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C.oin a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. APPARATUS AND TECHNIQUE The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 0800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard' glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not 'a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by

Jan 1, 1944

By W. H. Gauvin, N. J. Themelis

Jan 1, 1963

By L. W. Page

PrEvious to the introduction of the motor vehicle the broken stone or macadam' road met the conditions of rural horse-drawn traffic better than any other type of road, but under fast motor traffic it has been proved to be quite unsatisfactory, and necessitates high maintenance charges. Such a road depends for its success upon the fact that the rock dust fills the voids between the stones and acts as a cement or binder. Under ideal conditions it should be constructed of rock so suited to the volume and character of horse traffic that only enough fine dust is worn from the stones of which the road is composed to take the place of that carried off by wind and rain; and when these conditions are met, the fine dust resulting from the wear of traffic forms with the stone a smooth, impervious shell, shedding the surface water and protecting the foundation. With increase in the number and speed of motor vehicles, however, it was soon found that the cost of maintenance also increased, until at the present day highway engineers consider the old method of constructing and maintaining broken-stone roads increasingly inadequate, and are introducing every known type of binding material other than rock dust to cement the stone together. Among the most prominent types of products in use are those produced from our various petroleums. That the value of modern methods of road preservation was appreciated in this country much earlier than we have been accustomed to believe is demonstrated by the recent revival of an old patent which was granted to one John Martineau, of Elbridge, N. Y., in 1834. Petroleum had, of course, not been discovered at that time, but he claims as his invention and improvement "The application of tar, turpentine, or any of that class of tenacious, cohesive substances, reduced before use to a fluid state, and that state used as a cement, to apply to, and combine with sand, gravel, pebbles, and pulverized stone, such as is used for a Mc-Adam road, or cobble stone, the interstices of coarser material being in all cases filled,'as well as may be, with sand and gravel and cemented with tar or turpentine, to form the wearing face or surface of streets,

Jan 1, 1915

By E. T. Turkdogan, M. L. Pearce

The rates of sulfurization and desulfurization of calcium aluminate, silicate, and ferrite melts by CO + CO2 + SO2 mixtures at 1550°C are reported. It is shown that for melts 10 to 15 mm deep transport of sulfide ions within the melt controls the rate of sulfur transfer. The rate data from shallow melts, i.e., 1 to 4 mm deep, have been analyzed on the basis of a diffusion or a reaction controlled process and indications are that the both processes may play a part in controlling the rate of sulfur reaction. The rates of desulfurization of silicate XVEACTION equilibria between metals, metal oxides, and gases have received considerable attention in recent years. However, the understanding of and aluminate melts increase with increasing PCO2/PCO ratio in the gas stream, the effect being most marked for aluminate melts. The sulfide equilibrium data obtained from the present work are shown to be in accord with the results of previous studies. It is shown that carbon dioxide has a measurable solubility in silicate, aluminate, and ferrite melts. Consideration is given to the partial equilibria which control the directions and the rates of reactions occurring simultaneously in complex heterogeneous systems. the kinetics of heterogeneous reactions, particularly those occurring at elevated temperatures has not been improved appreciably. Almost all the metallurgical reactions occur in heterogeneous systems involving two or more phases. Although in many authoritative text books and original Papers the basic principles concerning the kinetics of heterogeneous reactions are clearly underlined, they are seldom used to the best advantage in kinetic studies, particularly those involving the metallurgical reac-

Jan 1, 1963

By R. V. Wheeler, W. Francis

Of the methods that have been used for studying the chemical composition of coal, attack by reagents has not, in general, yielded much information. Most of the reagents used have been strong oxidants such as nitric acid or Schulze's solution. The use of a milder oxidizing agent, such as air at low temperatures, enables progressive changes in the character af the coal substance to be studied and thus helps toward an understanding of its constitution. British bituminous coals frequently have a banded structure. These bands (of four types) can be separated one from another and have been found to possess markedly different chemical characteristics, even when taken from contiguous portions of the same lump coal. It has been found convenient to give each of the ingredients of banded coal a distinctive name, more or less descriptive of its appearance, and the study of the chemistry of bituminous "coal" in England has resolved itself into a study of each ingredient separately. The coal chosen for this work was taken from the Top Hard seam at East Kirkby colliery, Nottinghamshire, a detailed chemical analysis of which has been recorded by Baranov and Francis.' The banded structure was well marked and the bands could readily be separated. The research was confined to the brilliant vitreous bands (vitrain), the dull hard bands (durain) and the "sooty partings" main); for previous work had shown that the fourth type, to which the name clarain has been given, is intermediate in character, chemically, between vitrain and durain. The method of experiment was, briefly, to draw a slow current of moist air through weighed samples (50 gm.) of the three ingredients, vitrain, durain, and fusain, in the form of powder (through a 60-mesh and on a 90-mesh sieve) contained in glass tubes which could be maintained at a constant temperature during prolonged periods. After passing through the coal, the air bubbled into a measured volume of

Jan 1, 1925

By Francis Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other indus-tries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phos-phorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater impor-tance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appear-ance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1935

By C. S. Corbett

There is much comment at present in the ranks of the oil industry regarding unit operation of oil fields and the benefit that would accrue if it could be extensively applied. It seems certain that, as an immediate corrective of the present situation, overproduction could be effectively curtailed with all the advantages of proper conservation of petroleum resources and with no important loss to anyone connected with the industry. Unit Operation in Certain Foreign Fields Many an oil operator in America would doubtless like to have exclusive control of one or more oil-bearing structures for development in accordance with the economic position of the industry and especially in accordance with the best production practice known. A few operators now have this privilege, particularly in certain foreign fields, and are following lines of procedure which show that they are aware of the great opportunity that is theirs. We find in an article by Professor Strigeoff,1 and in a paper read by Captain Comins2 before the American Petroleum Institute, the outlines of procedure adopted, respectively, by the Soviet Government for the nationalized Russian oil fields and by the Anglo-Persian Oil Co. for its fields in Persia. Comprehensive plans for the unit operation of other oil fields may have been described publicly but no such descriptions have come to the attention of the writer. New fields are coming more and more into the hands of single operators or of a few who control large activities and who appreciate fully the need for cooperative action and are willing to forego the lure of a large quick profit from high flush production in order to secure the advantage of better stabilization in the industry and a larger though more deferred profit by operating the field as a unit. Much can be done toward efficient development of an oil field controlled by a few operators who are willing to cooperate for that purpose, but the best result can be obtained only by pooling their interests in the field

Jan 1, 1930

By Thomas M. Barczak, Claude A. Goode

Principal criteria in the design and operation of longwall mining systems are examined. The decision to apply longwall mining is investigated from an economic viewpoint, and the impact of economics on system design are addressed. Geological considerations and requirements for effective long- wall mining are provided. Ground control factors determining panel design are outlined, as well as environmental considerations. Operational practices are discussed and alternatives recommended. The impact of face moves and the potential for mining wider webs are assessed. Constraints to production are identified and the potential for increasing production of longwall systems is established.

Jan 1, 1982