Search Documents

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By F. C. Oliphant, George H. Fancher

Two samples of drilling mud from the Hastings oil field, Texas, were tested, and the solids in each were separated into small fractions of a limited range in particle size. The mineral composition of each fraction by X-ray analysis is reported, and the results are interpreted in relation to other measured quantities, such as the physical properties of the original samples and the density of the various fractions. It was found that only 7 to 8 per cent by weight of the solids was of colloidal dimensions and that neither of the samples contained montmorillonite but did contain illite. Considerable calcite was also found. These data should be useful to the geologist interested in the origin and history of sedimentary strata as well as to the petroleum engineer. Introduction The questions, What is good drilling mud? What constitutes bad drilling mud? are pertinent, because the proper use and control of drilling fluids has been a factor of great importance in the successful drilling and completion of oil wells since the days of Captain Lucas. Adequate control of the characteristics of drilling fluids has assumed greater significance comparatively recently because of the problems introduced by caving formations in deep wells, costly blowouts and impressive mud bills. Much is known about the solution of some of the problems but, despite extensive research directed toward a better understanding of the physical and chemical properties of clay suspensions, it is difficult to define precisely a drilling mud, and much more difficult to say what constitutes a good mud. It is generally believed that the smaller particles of a drilling mud greatly affect its physical properties. In fact, it is customary to blame the colloids in a mud for nearly everything that goes amiss, because colloidal properties have effects out of all usual proportion on viscosity, filtration rate and reaction to electrolytes. It is germane to know whether drilling muds possess colloids and if so, the quantity and kind. Source oF Samples Two drilling muds from the Hastings oil field, Brazoria County, Texas, were selected because it is generally agreed that in this oil field good natural muds made solely from formations penetrated by the drill can be used until the well is nearly ready for completion. Customary drilling procedure in this field is to spud in with water, set a protective string of pipe, drill to 2500 ft. and set the surface casing. Drilling is continued to 5500 ft. with no treatment of the drilling fluid other than addition of water to

Jan 1, 1943

By Robert S. Baker

It has been demonstrated in the laboratory by A. J. Phillips1 that a transformation or conversion from beta directly to alpha may take place in a brass of 61 to 62.5 per cent copper content. The completion of the transformiation is dependent on a rapid rate of cooling from the all-beta field through the alpha + beta range to the alpha field. Phillips states that in a slowly cooled alloy containing 62 per cent copper and 38 per cent zinc the copper content of the beta is progressively decreased from 62 to 56 per cent by precipitation of alpha. Rapid cooling tends to prevent the separation of alpha with a copper content of more than 62 per cent by reducing to a minimum the time required for passing through the alpha + beta range. Upon crossing beyond the (alpha + beta) (alpha) boundary to the all-alpha region below, the material is transformed from beta to alpha. It, is essential that there be no change in composition. Phillips obtained his results by quenching a 62:38 copper-zinc alloy from 850" C. in iced brine at -8" C. No reference to the occurrence of this transformation in a manufacturing process has been found in the literature. An investigation of the microstructures of a number of hot forgings made from leaded brass rods yielded one forging in which this striking conversion from beta to alpha had occurred. The purpose of this paper is to describe the transformation and certain conditions under which it may occur during the hot pressing of brass. The conversion was noted in a shape forged from a leaded brass rod, the composition of which was: Cu, 60.26 per cent; Zn, 37.86; Pb, 1.88. In this study the lead content was disregarded and the alloy was considered to be equivalent to an alloy of 61.40 per cent copper and 35.60 per cent zinc (9812 parts = 100 parts). The possibility that the lead might obstruct or accelerate the precipitation of alpha was not studied. The lead appears as black globules in the photomicrographs and has a negligible solubility in the alloy.

Jan 1, 1932

By Subhas G. Malghan

The response of feldspar flotation to tallow diamine dioleate collector in the presence of sulfuric acid is studied using batch flotation experiments. Application of this nonhydrofluoric acid (non-HF) reagent system in the flotation of mineralogically and chemically different feldspar ores is compared with that of the conventional hydrofluoric acid system. The dependence of flotation recovery and concentrate grade on feed particle size distribution, conditioning time, pulp density, and pH, combined variation of collector and acid addition rates, sodium hydroxide concentration in the collector solution, and initial pulp pH Prior to conditioning is studied. The results have been discussed in relation to applicability of the non-HF system to plant trials, and the nature of the collector adsorption in the selective flotation of feldspar.

Jan 1, 1982

By M. B. Ramachandra Rao

The spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° 17' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1—the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous mica-chlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, litho-margic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. Method of Survey and Apparatus Employed The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The Potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1946

By M. B. Ramachandra Rao

The spontaneous polarization surveys dealt with in this paper were carried out near Guddadarangavvanahalli (lat. 14° 17' N.; long. 76° 24' E.) in Chitaldrug district, which forms part of the Chitaldrug schist belt. The occurrence of gold, copper, lead and antimony ores has been noticed for several years but efforts to exploit them have been unsuccessful, therefore some spontaneous polarization surveys were made in the hope of finding indications of workable ore bodies. The country examined has a rugged topography, with numerous hills on which there is little vegetation. The climate is generally dry, the average annual rainfall of the tract being about 25 in., of which 17 in. occurs during the southwest monsoon. The geological formations of the area pertain to an ancient schistose series known as the Dharwar system (Archean). Locally, the rock formations have been divided into three series1—the chloritic series (or the Chitaldrug formation), the clay series (or the G.R. formation) and the trap series (or the Jogimardi trap). The chloritic series includes a complex of altered ancient traps and volcanic agglomerates intermixed with some schists of sedimentary origin, all of which are highly metamorphosed. The lithological types of this series are mostly distinguishable as greenstone schists, calc-chloritic schists, slaty schists, ochery and calcareous mica-chlorite schists, with subordinate bands of secondary limestone. The clay series (G.R. formation) is made up of shaly and argillistic schists, litho-margic clays, sandstones and brecciated ferruginous quartzites. The Jogimardi trap is mostly of the nature of an epidiorite (hornblende diabase), which is distinctly intrusive in the form of large laccolithic and narrower dikelike masses. In addition to this trap, there are other minor intrusives such as the chalybitic trap, quartz porphyry and quartz reefs. The topographical and geological features of the area are noted on the map of Fig. I. The locations of some of the spontaneous polarization centers determined by the geophysical survey are indicated also. Method of Survey and Apparatus Employed The spontaneous polarization surveys were carried out in the manner recommended by the Imperial Geophysical Experimental Survey.2 Preliminary reconnaissance was first carried out along a series of parallel traverse lines that were laid out over the area. The Potential profiles obtained in these traverses were plotted* on a suitable scale and when any

Jan 1, 1946

By Sidney A. Swensrud

This paper reviews the subject of gasoline margins, discusses some of the more current marketing problems, and gives some consideration to the main urges to marketing expansion, or overexpansion, in the oil industry. Margins In an earlier paper1, some comparisons were shown for the years 1929, 1930 and 1931, of the margin between the refinery cost of gasoline in Oklahoma, the market price in Oklahoma, and the average retail price in 50 representative cities of the United States. These figures indicated a small margin for the refiner in 1929 between his gasoline cost and the wholesale price, which, however, had turned into a loss by 1931. The margin between either refinery costs or wholesale prices and the retail price in the 50 cities showed a continuous decline during the three years. We have now worked out these figures on a similar basis for a longer period—from 1928 through 1936. The figures for refinery gasoline cost are slightly different from those in the earlier study, owing to the use of

Jan 1, 1937

By C. McLean, Erickson, S. G. Kolb, S. C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined with underground workings during 1980-82 by Esso Erz GmbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceives as a cost-effective procedure to answer quest ions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gamma probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross-cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 m thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1984

By E. W. Krampert

The oil industry was very active in Wyoming in 1936, in contrast to the several quiet years preceding. Production for the year again increased about 7 per cent, following an 8 per cent increase in 1935. During the year, 85 oil wells were completed, compared to 55 in 1935. Three gas wells were completed in 1936, and three in 1935. At the end of the year 45 wells were drilling, as compared to 55 drilling at the end of 1935. Two new oil fields and one new gas field were discovered in Wyoming during the year. In the year 1936 Wyoming produced 14,475,431 bbl. of oil, a gain of 1,001,081 bbl. over the 1935 figure of 13,474,350. This increase, in the main, was due to the taking of light oil from the newly developed Sundance sand pool at Lance Creek, and from the new fields, Quealy and Medicine Bow, which contributed their first production this year. Most of the other old fields either were partly shut in in competition with the new fields, or showed a normal decline. This was especially noticeable in the black-oil fields, where production had been slowly but steadily increasing for a number of years. During 1936 black-oil production decreased approximately 100,000 bbl. as compared to 1935. The only black-oil field to show marked increase was Garland, which managed to take the market from less favorably located fields. The production of Wyoming in 1936 was 11,358,757 bbl. of light oil and 3,116,674 bbl. of black oil. Salt Creek, with a production of 6,015,000 bbl., is still the largest single oil-producing field, accounting for 42 per cent of the year's total production. Lance Creek, an old field, with newly developed production in the Sundance sand, reached second place this year for the first time in its history, with a production of 1,878,486 bbl. Lance Creek production will almost equal that of Salt Creek in 1937, if the present rate of production is maintained during the coming year. Oregon Basin, a large black-oil field, held second place in 1935, but owing to a greatly lessened demand for its production, dropped back to third place in 1936. This was in part due to greatly increased light oil available, and in part to the greater supply of black oil available at

Jan 1, 1937

No. 345.-Assayer. A man 35 years old, or over, experienced in general mineral assaying, particularly of tin and tungsten ores. To locate in Bolivia with a strongly established house. No. 346.-A firm of consulting and managing engineers, having charge of certain coal-mine properties in Illinois, requires the services of the following: (a) Mine transitman, who has had underground experience and is capable of making accurate surveys. Salary $150 per month to start. (b) Mining engineer, possessing strong personality, and experienced both in surface and underground work, who is capable of taking complete charge of several coal properties. Salary $175 per month. (c) Four rodmen for mine surveying. Salary $85 per month to start. Candidates for the above positions should be able to report to the company's Illinois office at once. No. 347.-A South African development company will shortly require the services of a mill superintendent, who has :a general knowledge .of concentration, particularly of flotation, and is able to take charge of a copper concentrator treating 15,000 tons per month and employing 200 natives and a small number of white men. Salary is £60 per month to start, and the company supplies an unfurnished room or house, including free light, free water and free sanitary service, together with one native house servant. I A contract will be made for six months, and notice of three months by either party will be required to terminate the engagement after six months. An allowance of £75 for travelling expenses will be paid on arrival in South Africa to a single man, or £125 to a man who brings his family. Salary begins upon arrival

Jan 10, 1918

By AIME AIME

A STUDY of subsidence and ground movement in the copper and iron mines of the upper peninsula of Michigan has been made by W. R. Crane of the United States Bureau of Mines and published as Bulletin 295 of 66 pages and 49 illustrations. As a result of subsidence, the country adjacent to the mines and over- lying the mine workings in this district is often broken to such an extent as to affect its value; mine shafts and development openings are occasionally so damaged as to be rendered useless, and water can enter the workings through fractures and cave-ins. The problem is more serious in the iron-mining districts, where villages and towns not owned by the operating companies have grown up around mining operations.

Jan 1, 1929

By W. M. Johns

The geological mapping of Lincoln and Flathead Counties was a five-year project undertaken by the Montana Bureau of Mines and Geology. This paper, written by the Project Geologist of the survey, is primarily concerned with the stratigraphy of the Belt rocks encountered in mapping. Lincoln and Flathead Counties of northwestern Montana are underlain by sedimentary rocks of the Belt Series of Precambrian age. In only a very small part of the area, near Libby and Troy, have economic mineral deposits been worked with any success. Most of the area has been inadequately mapped as to geology. The region is crossed by the Great Northern Railway and served by the Pacific Power and Light Co.; officials of these two companies believed that with better geologic maps, prospecting might be stimulated and lead to the discovery of mineral resources that would contribute to new economic development within the area. A cooperative mapping agreement was proposed jointly by the two companies to the Montana Bureau of Mines and Geology in May 1958, and thus was born the Kootenai-Flathead five-year project. The dual objectives of this project are: 1) the possible location of mineral deposits of economic value, and 2) the ''stimulation of prospecting exploration" by others. This was to be achieved by geologic mapping of some 6800 sq miles and by establishing a field office in Kalispell where prospectors could come to have their rocks and minerals identified and receive geological advice on their problems. This writer has finished four field seasons as Project Geologist and thus became familiar with the Belt section in the Libby, Yaak River, Ural, Thompson Lakes, Pleasant Valley, and Stryker quadrangles (see Fig. 1). Progress on the project is given in annual reports issued by the Bureau.* This *Montana Bureau of Mines and Geology, Bulletins 12 (1959), 17 (1960), and 23 (1961). paper is concerned essentially with the stratigraphy of the Belt rocks so far encountered in mapping. PREVIOUS WORK IN THE AREA Willis28 made the first study of the stratigraphy and structure in the Lewis and Livingston Ranges of Glacier Park just east of the project area. In 1904, Daly made a study of the Belt rocks of the 49th parallel, using the names from bottom up, Creston, Kitchener, Moyie, and Gateway, for rocks ranging in age from that of Prichard to that of basal Missoula group. Walcott26 studied the Belt rocks exposed in the Mission Range (see Fig. 1) and other areas to the south of the area under discussion. Calkins and McDonald made a reconnaissance of northern Idaho and northwestern Montana in 1905. Calkins was the first to use Walcott's term 'Ravalli' as a group name for the strata equivalent to the Burke, Revett, and St. Regis formations (see Table I). Clapp worked on the Belt of western Montana (including Lincoln and Flathead Counties) throughout his lifetime. The Fentons9 studied the Belt of Glacier Park and

Jan 1, 1962

By R. V. Ramani, Y. J. Wang, R. Mishra

Abstract-The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine

Jan 11, 1978

By Henry Mulryan

DIATOMS are microscopic aquatic plants of the order Bacillariaceae. They are unicellular plants with skeletons made up of amorphous opaline silica. The skeletons show highly ornate, complicated geometrical designs. Diatoms live in water virtually everywhere. They are found in clean sea water, brackish water, and fresh-water lakes and ponds. When conditions are right, diatoms propagate by subdivision in huge numbers. Alkalinity, temperature, and the presence of high concentrations of silica in the water largely control diatom life. When the diatoms die the skeletons drop to the bottom of their habitat to form oozes of varying thicknesses. DIATOMITES Diatomite, or diatomaceous earth, is composed essentially of the siliceous remains of the diatoms, although other organic skeletons are also present, especially in sea-water deposits where radiolaria, sponges and silico-flagellates are common. Impurities are generally carbonaceous material, fine-grained silt, volcanic ash and dust, and occasional coarse grains of sand. Diatomites are marine, brackish, or fresh-water, depending upon types of diatoms and their method of deposition. DIATOMS More than 8000 species of diatoms have been named and classified. Some are definitely classified as to their habitat; some are so well recognized as to their living conditions that they can be stated to be diagnostic types, and when encountered in a deposit determine the origin of the deposit. Some of the commoner types of diatoms found in the fresh-water diatomites on the Pacific Coast are: [Cymbella lanceolata Agardh Fragilaria virescens Ralfs Encyonema prostratum Ralf s Diatoma vulgare Bory Surirella biseriata Brebison Eunotia major Ehrenberg Amphipleura pellucida Kutaing Stictodiscus niagarae Ehrenberg Gomphonema geminatum Lynberg Melosira granulata Ehrenberg]

Jan 1, 1939

Jan 1, 1903

By Paul L. Goddard, Alfred G. Hoyl, William R. Sirola

A good place to look for elephants is in elephant country, and old mining districts are certainly elephant country as far as minerals are concerned. In many areas probably more ore is still in the ground than has been taken out. The old timers were good miners and hard workers and when they left ore behind, it was usually for good reason; but many an old mining district has been revived by new approaches to old problems, taking advantage of new techniques and new equipment. One of these is the Front Range mineral belt of Colorado, which has produced minerals for the past 100 years through the ups and downs of mineral prices and the general economy. Gold, silver, copper, lead, and zinc have been found in abundance in the complex sulfide veins of the area. Between Idaho Springs and Central City lie several strong veins which have been mined successfully in the past. The two strongest of these veins, striking northeast-southwest, (Lake-Bald Eagle), and northwest-southeast, (Crown Point-Belman) , and dipping northeast and northwest, respectively, intersect in a flat X near the head of Virginia Canyon. From the lowest drainage of the area, Clear Creek Canyon, the old timers drove the Central, or Big Five, haulage-drainage tunnel due north. It intersects the two veins 8460 ft from the portal and 1670 ft below the surface. The two veins were mined successfully at the surface and at the tunnel level. Without an opening to the surface at the in- side end of the tunnel, ventilating became very difficult as the stopes were opened up, and mining ceased in 1929. Vertically, 1200 to 1600 ft of virgin ground remains in the veins.

Jan 6, 1959

By Dietmar Espig

Very useful general relationships between operating parameters and the operating results for open- and closed-circuit grinding under steady- state conditions are described. The basic idea of the developed methods consists of the introduction of a known reference state. The relations derived from very simple approximations to individual processes allow one to evaluate fineness and mass flow of the desired state after changing the parameters (feed rate, fineness of the feed material, mill length, transport behavior through the mill, classifier characteristics). It was also possible to derive some general relationships, e.g., * an equation for the influence of the operating parameters of the mill on the fineness of the mill output * a criterion to establish if the desired state of a closed grinding circuit is steady state at all * a possibility to substitute the common influence of the transport behavior of the mill and of the classifier by-pass fraction with the coarse stream on the mill outlet product by means of a fictitious worse transport behavior. The applicability of the described methodology to many problems in grinding practice, including questions of controlling grinding circuits, is demonstrated by some examples. In particular, a working diagram of the standard closed grinding circuit has been established.

Jan 1, 1984

By R. R. Nash, W. F. Sheely, E. D. Levine

ThiS note reports on the variation with temperature of critical stress for basal slip of binary solid-solution single crystals of indium and of thorium in magnesium. PROCEDURE Alloy single crystal spheres were acid machined to 3/8-in. diam cylinders with the basal planes of the crystals normal to the cylinder axis and then annealed at 810°K. Stress was applied parallel to the slip system, (0001) [1120]. Experimental details will be presented in another paper.' Two nearly equivalent' techniques of stressing were used. Stress on the magnesium-indium alloy crystals was increased by 1 g per sq mm at 1-min intervals, and the critical flow stress was defined as the lowest stress to pro-

Jan 1, 1960

By C. E. Wood

THIS paper is a brief report of experimental work undertaken to determine whether barium oxide in any quantity increases the desulfurizing action of blast-furnace slags. Industrial furnace operation with slag containing small quantities of barium oxide, referred to later, interested S. A. Sanford of the Commercial Chemical Co., Youngstown, Ohio, to conduct experiments to furnish comparative results on desulfurization with normal slag and slag containing small quantities of barium oxide. The U. S. Bureau of Mines agreed to assist on the problem because of the possible saving in fuel if the desulfurizing action of blast-furnace slag can be substantially increased, also because the experiments would yield new information on sulfur elimination in general, a matter of economic importance in furnace practice. A more complete and fundamental study of desulfurization of iron by slag is in progress.

Jan 1, 1929

By Warren E. Wilson

PRESENT-DAY design of launders is essentially an art depending to a marked degree upon the experience of the designer, whose problem is that of determining the dimensions of a conduit that will transport the pulp within the physical limitations of the plant and in the most economical manner. This paper has been prepared in an effort to place launder design upon a more scientific basis. A method is developed from elementary principles and presented in a form that may be used directly by the designer in determining launder dimensions.. The equations that are developed are believed to represent an advance over older ones, in that they give due consideration to all the pertinent variables, either including them in the analysis or showing that they may be neglected within the limits of applicability of the equations. Experimental data from several sources are used in evaluating the coefficients that are not determined in the mathematical analysis. On the basis of the material presented, it is concluded that launders may be designed with a much greater degree of accuracy than previously believed possible, when due consideration is given to all the factors involved in the problem. However, a great deal of work still remains to be done in the laboratory before a complete answer to all the questions in launder design can be made available. HISTORY OF LAUNDER DESIGN Among the references1-11 are cited accounts of many experiments that have been conducted in an effort to advance the knowledge of the flow of liquid-solid mixtures in flumes and pipes. With three notable exceptions, this work was carried on in such a manner that the results have limited value in solving the general problem, since not all the pertinent variables were measured and controlled. The exceptions are found in the works of Blue,6 Gilbert,7 and Blatch,11 who exercised great care in controlling and measuring all the significant quantities involved in the experimentation. It is notable that much of the work done by men directly connected with the mineral industries1-4 lacks somewhat in completeness, owing apparently to preconceived notions concerning the factors that determine the flow. For example, many measurements on flow in pipes and flumes carrying liquid-solid mixtures determined only the slope and percentage of solids, with no mention of size of particles, depth of flow, roughness of channel or specific gravity of solids. Material in current handbooks8,9 and textbooks is based largely on the experimental work cited above. Although most discussions of the topic-include statements that the results to be obtained by using the data presented are limited by the fact that all variables have not been considered, it is

Jan 1, 1943