Search Documents

By F. J. Radd, R. L. McGlasson

The mechanisms of corrosion and corrosion fatigue damages to sucker rods are examined from a fundamental electrochemical viewpoint, and the relationships of sucker rod microstructures to these damaging effects are defined. The common corrosive agents in crude oil production and storage are discussed as to types of attacks that they cause. The variations of fatigue strength with alloy content, surface preparation, and stress ranges are analyzed. Finally, conclusions are drawn as to how microstructures largely influence and control sucker rod performance. INTRODUCTION Greater than 90 per cent of the crude oil produced by artificial lift methods is produced through sucker rod pumping systems. In the USA each year more than $14 million is spent for sucker rods in new and old pumping installations. It is important to make this investment a wise one. Essentially, the sucker rod system is a long series of steel rods, operating under alternating stress loadings and under mechanical vibrations, which connect the surface power source with the subsurface pump. These rods often operate in a variety of corrosive media, including water, brines, carbon dioxide, hydrogen sul-fide, and air. Basically, this paper is concerned with the problem of the behavior of certain steels in various corrosive media under high and dynamic stress patterns. The main objective of this paper is to show how, once the stress effects and the corrosive environments are defined, one can still realize structural control and beneficial influence upon corrosion and corrosion fatigue. FUNDAMENTAL DEFINITIONS AND ANALYSIS In the corrosion and stress behavior of this solid state mixture of iron and iron carbide called steel, one must analyze upon what major factors does its service life depend and of what, exactly, is steel composed. The former question can be referred to two external factors and two internal factors. The two major external factors are: 1. the nature of the stress patterns — size and range of stresses present 2. the nature of the corrosion — erosion environment — the corrodent and/or wear involved The two fundamental internal factors that govern the strength and useful life of a steel both in normal duty and in heavy-duty corrosion service are: 1. the nature of the steel volume properties 2. the nature of the steel surface properties For the latter question normal steel is defined as a solid mixture of iron and iron carbide particles, generally with certain accidental and intentional elements present. (The amount of iron carbide present is determined by the carbon content of the steel.) These additional elements generally dissolve into either the iron (ferrite) or the iron carbide (cementite) components.

Jan 1, 1955

By Frank H. Armstrong

All the mining machinery of the Penn Iron Mining Co. has been operated by electric power for several years and when another shovel for stockpile loading was required the advantages of an electric shovel were naturally considered. After considerable study, serious objections suggested themselves the use of a shovel operated directly by electrical apparatus by reason of the complicated control, severe service on the motors and the heavy surges of current required from the line. It was finally decided to construct an electro-hydraulic shovel using water under pressure to perform all the necessary operations except that of propelling, for which a separate motor was best suited. A car body with boom, dipper handle and dipper of late design, but without any of the steam machinery, was purchased. A motor-driven centrifugal pump, a pressure tank, an air tank, a small air compressor and water cylinders with plungers, pistons and valves, were installed in place of the steam equipment. Fig. 1 shows this shovel under construction and Fig. 2 shows it as it was operated during the first year, the summer of 1914. The large tank at the back of the car, in Fig. 1, carried air under

Jan 1, 1916

By W. B. Tijmann

Maintaining safe, yet economical, slope geometries in a mining operation is paramount. When design analysis and engineering judgement have dictated conservative and usually more expensive problem solutions, monitoring has often proven to be a valuable method in dealing with potential slope instability. A well planned and executed monitoring program can allow operation at a lower theoretical margin of safety. Monitoring provides a valuable check on design parameters and can measure effects of remedial improvements. Warning of impending failure can often be established well in advance. The monitoring problem situations in civil engineering works and open pit mining are much alike. Instruments used for monitoring in both industries are often the same. In this paper, geotechnical instruments for measuring deformation and groundwater pressure in rock and overburden are discussed with a broad-brush approach. Results obtained over extended time periods are presented in a graphical presentation for a case history. Descriptions of various types of instruments, mostly used to monitor stability of rock slopes, are discussed, and data analysis and approximate costs are presented.

Jan 1, 1983

By R. E. Lund, D. E. Warnes

SELECTIVE sulfation of individual constituents in ores or metalliferous products has received increased attention in recent years. The fluid-bed reactor with its advantages of close control of both temperature and atmosphere promises to have ap-

Jan 1, 1958

By L. B. Herring, Harold Decker

The area under discussion includes districts 2 and 4, so designated by the Texas Railroad Commission,‡ and comprises the following 26 counties: Bee, Brooks, Calhoun, Cameron, De Witt, Duval, Goliad, Gonzales, Hidalgo, Jackson, Jim Hogg, Jim Wells, Karnes, Kenedy, Kleburg, Lavaca, Live Oak, Nueces, Refu-gio, San Patricia, Starr, Victoria, Webb, Willacy, Wilson and Zapata. Drilling and Production The total number of wells drilled in this district during 1944 is shown in Table 5. This indicates a 41 per cent increase in all drilling over 1943. In spite of every handicap created by the war, the oil industry more than met the crisis in its drilling program in this district. Last year we thought it would be impossible to add to the total number of wells drilled in the previous yea;, but in spite of the lack of manpower and materials this large increase was shown. During 1944 this district produced 124,201,978 bbl. of oil from 11,607 producing wells, whereas in 1943 it produced 88,421,693 bbl. from 11,211 producing wells. This is an increase of 35,780,285 bbl. of oil. Some decline has been shown in the older fields arid undoubtedly the majority of wells in the district are producing at too high a rate. However, this district has been able to meet any demands made on it by the Petroleum Administration for War for increased production. Discoveries and Extensions There was a slight decline over the preceding year in the number of wildcats drilled, but the number of discoveries increased. In most instances subsequent development has not been sufficient to arrive at preliminary valuations but it appears that the over-all oil discoveries were below normal and that the gas discovcrics were relatively more important. The Canolis and Tijerina pools, Jim Wells County, and the Dan Sullivan pool, Brooks County, appear to be the outstanding oil discoveries of the year. No important oil reserve was discovered or developed in the Wilcox horizons, although considerable wildcatting was done. Important extensions were made at Agua Dulce and Stratton in Nueces and Teleberg Counties. Production was increased appreciably at Willimar, Willacy County, and Seeligson, Jim Wells County, in sands and areas which were apparently productive at the beginning of the year. Refining Most of the major work in the changing and completing of refineries was finished this past year. Some of the most modern refineries in the industry are now located in the Corpus Christi area. Gas and Condensate No new recycling projects were commenced during the year, nor were there any important additions to the old operations. No major gas reserve was developed, although several new discoveries suggest potentid possibilities.

Jan 1, 1945

By Heber Cole

THE gypsum industry of Canada, like all others connected with the construction business, has felt the full effect of the depression during the past few years, and sales of its products have been greatly curtailed. The year 1934, however, saw a decided turn for the better and a gradual but steady improvement is noticeable in all its branches. In many ways the depression has been a blessing in disguise to the gypsum industry; during the years from 1926 to 1930, demand increased so rapidly that companies were forced to expand and often new apparatus and machinery were placed in operation regardless of expense, or plants already existing were taxed to their limit and forced to keep running with the minimum amount of repairs. The depression, therefore, has really given the industry what might be called a breathing spell, in which it has had time to take stock of its position, to reduce its costs of production, to devote more serious attention to the quality of its products, and to con-solidate its operations into a smooth working whole, which as conditions improve will enable it to meet the demands of the trade with more varied products of a quality hitherto unattained. Progress in the gypsum industry, however, has not been confined to the years of the depression, for some of the greatest advances occurred under the spur of increased demand for its products by the building trade. The purpose of this paper is to review briefly some of the out-standing trends in the development of the gypsum industry in Canada during the past 10 or 12 years.

Jan 1, 1935

By Clarence Fenner

THE manufacture of optical glass is a process that demands careful regulation and control at all stages in order that satisfactory results may be obtained. The product, to serve its purpose, must meet stringent requirements, which can be assured only by careful procedure in manufacture. During the greater part of the time that a pot of glass is in the furnace, temperatures should be kept within certain rather narrow limits; a departure on either side is likely to be detrimental to the glass and may result in total loss. If the temperature during melting and fining be low, the melt is likely not to fine properly and the glass will contain quantities of bubbles, or "seed," or it may become milky and unfit for use; too high a temperature, on the other hand, is severe on the pot and may cause it to leak or cast stones, or the increased solution of pot material in the melt may acid to the color of the glass and decrease its transmission. Moreover, variations in the working temperature will mean variations in the amount of selective volatilization and, consequently, variations in optical properties from pot to pot. Furthermore, in the closing stages of furnace treatment, the melt is cooled until a certain degree of stiffness is attained, when the pot is withdrawn. The quality of the glass-its freedom from striae and bubbles-will depend in large measure on whether the temperature to which cooling has been carried is suitable. For each type of glass there is a narrowly restricted range of temperature to which each pot of the given type should be cooled before withdrawal. A quick and reliable method of measuring temperatures is, therefore, of the first importance. In the optical-glass work conducted by the staff of the Geophysical Laboratory during the period of the war, much attention was given to the clatter of determining what methods would meet the requirements. This article will deal with these investigations and with the application of the results to actual practice at various plants. At the. time that the work of the Geophysical Laboratory was begun at the Bausch & Lomb plant, each melting furnace was equipped with

Jan 7, 1919

By R. D. Daniels, T. W. Wood

The tensile properties of columbium and Cb-H alloys containing up to 455 ppm H were studied as a function of temperature and strain rate. Hydrogen, introduced into columbium at elevated temperatures, using a thermal -equilibrium technique, embrittled columbium most severely at about —77°C. This elnbrittle ment occurred even at hydrogen concentrations of an order of 20 ppm. At higher temperatures, the hydrogen tolerance of columbium increased in relation to the increased solubility of hydrogen in tile metal. Below this temperature hydrogen tolerance, as determined by ductility and fracture stress, increased slightly. Strain rate had little effect on the tensile results for cross-head speeds over the range 0.002 to 2.0 in. per min. Strain aging during the tensile test appears to explain the ductility mininmum at —77°C. The apparent increase in hydrogen tolerance at lower temperatures is attributed to the low mobility of hyhogen. Experiments were performed in which samples were prestrained in tension at room temperature and tested to failure at —196°C. Results suggest that hydrogetz segregation to preformed crack nuclei can cause subsequent embrittlement even at temperatures where hydrogen mobility is too low to cause embrittlement in a normal tensile test. COLUMBIUM is an example of the class of bcc metals with ductile-brittle transition temperatures sensitive to the presence of interstitial atom contaminants. Hydrogen is one of these embrittling contaminants. The embrittling effect of hydrogen is less potent, perhaps, in columbium than in some of the other bcc refractory metals, but it is still a problem of both theoretical and practical interest. Unlike hydrogen in iron and steels, hydrogen in columbium is exothermically rather than endo-thermically occluded. The embrittlement process in exothermic systems has not been studied as extensively as that in endothermic systems, especially at hydrogen concentrations below the limit of solubility. The purpose of this investigation was to evaluate the embrittlement process in initially pure columbium as a function of hydrogen content, temperature, and strain rate. The Cb-H phase diagram, according to Albrecht et al.,1 is shown in Fig. 1. Columbium reacts exothermically with hydrogen producing a solid solution at concentrations of less than about 250 ppm (parts per million by weight) H at room temperature. At concentrations above the highly temperature-dependent solvus a second phase is formed. Like many similar hydrogen-metal systems,2 his system exhibits a miscibility gap with respect to hydrogen solution. Albrecht found the critical temperature of the miscibility gap to be about 140°C, the critical concentration to be 0.23 atom fraction hydrogen, and the critical pressure to be 0.01 mm Hg. Above 140°C there is a solid solution of increasing lattice constant extending across the phase diagram. Hydrogen concentrations of particular interest in this investigation were those below the limit of solubility in columbium. At hydrogen concentrations above the limit of solubility, columbium will contain the hydrogen-rich second phase and will be brittle under most testing conditions because the hydride generally precipitates as platelets with coincident matrix lattice strains.1'3 At hydrogen concentrations below the limit of solubility, the tensile behavior of columbium is expected to be more sensitive to the interrelationships between hydrogen concentration and mobility and the testing variables such as temperature and strain rate. Literature references to the hydrogen embrittlement of metals, especially ferrous alloys and titanium alloys, are too voluminous to mention. It is only recently, however, that detailed studies of the hydrogen embrittlement of columbium have been undertaken. Wilcox et a1.4 studied the strain rate and temperature dependences of the low-temperature deformation behavior of fine-grained are-melted columbium (1 ppm H) and the effect of hydrogen content (1,9, and 30 ppm H) on the mechanical behavior of columbium at a series of temperatures for a single strain rate. A strain-aging peak was ob-served at about -50°C which was attributed to the presence of hydrogen in the metal. Eustice and carlson5 studied the effect of hydrogen on the ductility of V-Cb alloys at a series of temperatures over the range -196° to 25°C. Pure columbium was embrittled by 20 ppm H which produced a ductility transition at approximately -70°C. Ingram et al.6 studied the effect of oxygen and hydrogen on the tensile properties of columbium and tantalum. A minimum in the notched-to-unnotched tensile ratio of hydrogenated columbium was obtained at about -75°C, but because of the relatively large hydrogen content employed (200 and 390 ppm) the ductility

Jan 1, 1965

By W. L. Honnold

(San Francisco Meeting, September, 1915) OWING to a unique labor situation and other unusual circumstances, the mining methods of the Rand are hardly comparable with practice elsewhere. They are' of considerable interest, however, and their impor-tance is increased by the magnitude of the industry with which they are identified, gold of $166,186,000 value, say 40 per cent. of the world's production, having been recovered from 25,701,954 tons of ore milled in 1914. In the sketchy remarks to follow, attention will first be drawn to some influential factors of general bearing, after which certain features at two mines of the writer's group will be referred to. It is hoped that engineers associated with similar or different conditions and practice will contribute to broaden the discussion. Before proceeding, recognition is due the generous assistance of C. E. Knecht and F. A. Unger. GENERAL OBSERVATIONS The principal mines are situated along the northern limit of an irregularly shaped geological basin, and extend in almost unbroken continuity over a distance of about 60 miles. As the boundaries are defined by vertical planes there are both "outcrop" and "deep-level" properties, all differing in size and in technical features. So much has been written in regard to the geology of the Rand that only a few pertinent features need here be recalled. Briefly, the ore deposits are profitably enriched portions of certain conglomerate beds or "reefs," rarely more than three, which are interposed between quartzite, or quartzite and slate, and lie so closely together that where more than one are mined they are dealt with as a work-ing unit, although they may lie stoped separately. Their collective extension is locally referred to as "the Reef."

Jan 8, 1915

By D. Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abun¬dant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleis¬tocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional re¬sources. Limestone uses include cement and lime manufac¬turing, concrete sand and aggregate, road base material, beach sand replenishment, agricultural lime, and golf course construction.

Jan 1, 1984

By Orson Cutler Shepard, Charles F. Skinner

THE leaching method that was first widely used with the cyanide process consisted of percolation leaching of crushed ore in vats or leaching tanks. It was frequently necessary to separate the sand for cyanide treatment and discard the slimes, because only granular material allows the necessary amount of solution to percolate through it in a reasonable time. Later a slime process consisting of agitation followed by thickening and filtration was developed, and is extensively used to the present day. Even though the agitation-leaching slime process is considered satisfactory, the cost of plant and of operation are both greater than for a percolation-leaching plant of equal capacity. This situation has been recognized in the hydrometallurgical treatment of copper-bearing slimes; and a considerable amount of work has been done at the Southwest Experiment Station of the U. S. Bureau of Mines in an effort to develop a percolation method of treating slimes. Experimental work on the copper-leaching problem was started by H. E. Keyes1, and later tests were made by J. D. Sullivan and A. P. Towne2. The Bureau of Mines work resulted in the development of a process by which slimes were moisture-agglomerated with sand and crushed ore, to form a permeable mass through which solution could be trickled without breaking down the glomerules. The agglomeration trickle-leaching method was developed on a small scale and finally tried out in a 12-ton vat. Successful results were obtained as long as the leach solution was added slowly, so that the agglomerated charge was never flooded. If the leach solution flooded the charge, the glomerules broke down and the charge became impervious. There are two important difficulties in the application of the agglomeration trickle-leaching method to the cyanide process for gold and silver ores:

Jan 1, 1937

THE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently attempted to make a much too simple correlation between mineral discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail

Jan 1, 1941

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in .he discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in he smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently n the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of he joined pieces (base metal). The filler metal, older or braze, is always of lower melting point than the base metal. Consequently with these) recesses there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Joining operations carried out at temperatures above 500°C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used.

Jan 1, 1975

By F. G. Tickell, R. C. McCurdy, O. E. Mechem

The behavior of fluids in the voids of a rock is fundamental to the study of many of the problems of oil-field development and production. For it is by virtue of these openings between grains that oil and gas are able to move through the rock, to be contained by the rock, and to pass from the rock into the well. The capacity to contain fluids is measured by the porosity of the rock, and the ease of fluid movement is governed by the permeability. When the engineer wishes to estimate the amounts of oil and gas in an underground reservoir he is often concerned with the porosities of the rocks and, when dealing with problems relating to rate of production, he is more likely to be interested in the permeabilities of the rocks. Rocks are permeable because they are porous, but they may be porous without being permeable. Clays are very porous, and yet they are impermeable from a practical standpoint. Attempts have been made1 to correlate permeability with porosity for certain rock members but, where a definite relationship between these two properties is found to hold, it is purely fortuitous and local. Porosity and permeability do not necessarily bear any quantitative relationship to one another. The porosity of a substance is the percentage of void volume to bulk volume. The petroleum engineer is usually interested only in the inter-granular voids that are accessible to fluids. In measuring porosity he does not wish to include scaled openings. The measurement he desires is one of "available porosity," otherwise called "apparent porosity." The porosity of a natural aggregate of solid grains, such as a sandstone or clay, is governed by: (1) Grain-size distribution, (2) angularity of grain, (3) colloidal content, (4) degree of compaction. It is not difficult, for unconsolidated rocks, to measure the effect of any one of these when it alone is varied, and then to predict what the effects on porosity will be for such single variables. It is very difficult, however, if not

Jan 1, 1933

By T. B. Armstrong

Electrical energy conservation sees that service facilities are operated only when needed and that production equipment is operated under an optimum condition. Specific energy consumption (kw-hr per tonne) is not regularly recorded for comminution circuits because of variations in ore characteristics and the low grinding efficiency (0.1 to 2.0%) of the equipment. Improved data acquisition can produce meaningful results. Particle size monitor systems and density gauges permit comparison of energy (kw-hr) and production (tonne) for a "fixed" condition. Finding the operating condition producing the lowest unit energy consumption provides a target for an effective energy management program.

Jan 1, 1982

By Leonard Larson

DURING several years immediately preceding the adoption of wet-charge smelting at McGill, various necessary conditions affecting this procedure, such as plant rearrangement and the metallurgical nature of the concentrate produced at the concentrator, were fully considered. Wet-charge smelting is not altogether novel to the recently recon-structed smelter at McGill. A number of years prior to this improve-ment, when flotation methods were initiated at the concentrator, large tonnages of wet and (at that time) sticky flotation concentrate were charged directly into the reverberatory furnaces, because of the difficulty in handling the entire tonnage in the roasters. The plant had excess reverberatory units and this surplus furnace capacity was utilized to smelt raw flotation concentrate. During the years 1927 and 1928, a number of actual operating furnace test runs were made to determine in principle the feasibility of wet-smelt-ing operation. Results were encouraging, and in November 1932 the roasting plant was shut clown. For some time thereafter the wet feed was delivered directly to the reverberatory side-charging calcine hoppers already in place. Feeding the wet material through the old calcine hoppers and charge holes into the furnace involved considerable labor, but under the conditions existing at that time it was desirable to continue wet smelting even under the handicap of this laborious procedure. The smelting plant during this period was on a curtailed production basis, operating only about 15 days per month. The alternate starting up and shutting clown of the roasting plant presented a difficult problem and charging the wet material directly to the furnace entirely eliminated this difficulty. The roasting plant was never operated thereafter.

Jan 1, 1938

By D. B. Hobbs, H. O. Burrows, T. D. Stay

ALUMINUM which has lost its original identity as to source may be considered as secondary. This would include scrap originating in the fabrication of aluminum, which is not consumed at the plant of fabrication, and all material resulting from fabrication, which has lost its original identity regardless of whether it be consumed at the plant of fabrication or not. In general, secondary aluminum may be divided into two classes, commercially pure and alloyed. The chief impurities found in commercially pure aluminum are copper, iron, titanium and silicon; while in aluminum alloys, copper, iron, titanium, silicon, zinc, manganese, magnesium, nickel, or tin, may be present in varying proportions. Occasionally lead and antimony are found in secondary aluminum alloys, especially if the alloy results from remelting vender's automotive scrap. Such alloyed elements as are found in the scrap cannot be removed on remelting. In this, the remelting of secondary aluminum differs from the smelting of secondary copper or most other secondary metals. The majority of secondary materials reach the consumer in the form of remelt ingot or remelt No. 12 ingot. This ingot varies greatly in quality, depending upon the source of the material, and the manner in which it is refined and blended. The principal differences between primary and secondary ingot are: 1. The composition of secondary ingot may be more or less indefinite. 2. Secondary ingot may contain more dross and oxide. Secondary ingot may, however, be used successfully in a great many products. RELATION OF PRIMARY PRODUCTION TO SECONDARY PRODUCTION Table 1, compiled from data published by The American Metal Market, gives an approximate idea of the relation of primary to secondary production. Information obtained from other sources leads the authors to believe that the figures for secondary production are somewhat low.

Jan 1, 1928

By George Lehman

THE Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the ?shrinkage-stope" or "caving" methods ) a lower extraction of, the developed ore, at a lower mining cost. ORE-DRAWING TESTS To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or "caving" methods. As no definite information regarding the question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore.

Jan 9, 1916

By H. T. Clark, H. K. Work

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By H. K. Work, H. T. Clark

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940