Search Documents

By H. E. Stamm, H. H. Spain, R. C. Rumble

This paper presents a reservoir analyzer study of the performance of the Woodbine formation in the East Texas basin. The study was made possible by the compilation of available information on the configuration. thickness and the pressure drawdown of the formation. The investigation was made of the pressure variations in the basin incident to production from the several Woodbine reservoirs. In addition, the apparent compressibility of Woodbine water was evaluated so that the potential water yield of the formation could be determined. The distribution of permeability of the Woodbine sand and the interference between producing areas were also investigated. In conjunction with this basic study of the Woodbine sand, an acceptable match of the production-pressure relationship in the East Texas Field was established on the analyzer. INTRODUCTION When production is taken from a reservoir contiguous to an aquifer, the resultant pressure gradient causes a water influx into the reservoir. For some years it has been the practice to predict the performance of water drive reservoirs with mathematical equations that relate the water influx into reservoirs to their pressure behavior. A rigorous solution of these equations is quite complex: hence, the conventional method requires the simplifying assumptions that the formation have constant thickness, permeability and poiosity, and that it have a known and regular shape. It is necessary to use performance records of the reservoir in question to determine the equation constants that make the results of the mathematical calculations duplicate the reservoir history. The values of the constants determined in this manner sometimes differ so greatly from theoretical or measured values that the constants appear unreasonable. The equation constants comprise such factors as the thickness, porosity and permeability of the formation, and the viscosity and compressibility of water. Usually the thickness, porosity and viscosity are known within a reasonable degree of certainty. whereas the formation permeability and the water compressibility are known with considerably less certainty. Hence. permeability and compressibility values are arbitrarily selected that will make the mathematical equations duplicate the reservoir behavior. In many reservoir studies the value of the compressibility of water thus selected has exceeded the reported value by a factor of from severalfold to manyfold. Whether this excessive value results from the inadequacy of the mathematical approach to take into account the shape irregularities and the heterogeneities of the aquifer, or is due to some type of formation compaction and decrease of porosity has not been established. Because of the significance of the potential water yield of formations with reference not only to oil reservoirs but to water resources as well, it is very important that a representative value for the effective water compressibility be determined. One of the best known examples of a field for which it has been possible in the past to predict the future reservoir pressure is the East Texas Field. Until about 1943 it was possible by means of mathematical equations to duplicate past pressure behavior and to predict with a high degree of accuracy the reservoir pressure of the field. Since 1943, however, the calculated pressures have deviated progressively from the observed pressures to such a degree that in recent years, it has

Jan 1, 1951

By H. H. Spain, R. C. Rumble, H. E. Stamm

This paper presents a reservoir analyzer study of the performance of the Woodbine formation in the East Texas basin. The study was made possible by the compilation of available information on the configuration. thickness and the pressure drawdown of the formation. The investigation was made of the pressure variations in the basin incident to production from the several Woodbine reservoirs. In addition, the apparent compressibility of Woodbine water was evaluated so that the potential water yield of the formation could be determined. The distribution of permeability of the Woodbine sand and the interference between producing areas were also investigated. In conjunction with this basic study of the Woodbine sand, an acceptable match of the production-pressure relationship in the East Texas Field was established on the analyzer. INTRODUCTION When production is taken from a reservoir contiguous to an aquifer, the resultant pressure gradient causes a water influx into the reservoir. For some years it has been the practice to predict the performance of water drive reservoirs with mathematical equations that relate the water influx into reservoirs to their pressure behavior. A rigorous solution of these equations is quite complex: hence, the conventional method requires the simplifying assumptions that the formation have constant thickness, permeability and poiosity, and that it have a known and regular shape. It is necessary to use performance records of the reservoir in question to determine the equation constants that make the results of the mathematical calculations duplicate the reservoir history. The values of the constants determined in this manner sometimes differ so greatly from theoretical or measured values that the constants appear unreasonable. The equation constants comprise such factors as the thickness, porosity and permeability of the formation, and the viscosity and compressibility of water. Usually the thickness, porosity and viscosity are known within a reasonable degree of certainty. whereas the formation permeability and the water compressibility are known with considerably less certainty. Hence. permeability and compressibility values are arbitrarily selected that will make the mathematical equations duplicate the reservoir behavior. In many reservoir studies the value of the compressibility of water thus selected has exceeded the reported value by a factor of from severalfold to manyfold. Whether this excessive value results from the inadequacy of the mathematical approach to take into account the shape irregularities and the heterogeneities of the aquifer, or is due to some type of formation compaction and decrease of porosity has not been established. Because of the significance of the potential water yield of formations with reference not only to oil reservoirs but to water resources as well, it is very important that a representative value for the effective water compressibility be determined. One of the best known examples of a field for which it has been possible in the past to predict the future reservoir pressure is the East Texas Field. Until about 1943 it was possible by means of mathematical equations to duplicate past pressure behavior and to predict with a high degree of accuracy the reservoir pressure of the field. Since 1943, however, the calculated pressures have deviated progressively from the observed pressures to such a degree that in recent years, it has

Jan 1, 1951

By Harry E. LeGrand

Most mine operations are hampered to varying degrees by excessive inflow of water into mines or scarcity of water for processing the materials. These internal problems are compounded in many cases by such external hydrological problems as lowering of ground-water levels in areas outside the mine properties, subsidence of ground surface, adverse geochemical changes, and pollution. The development of a mine below the water table disturbs the natural ground-water system, causing a convergence in the flow of water from a surrounding area. The mine becomes the apex of a depressed cone in the water table. The fact that mines are commonly located in complex and somewhat anomalous geologic environments prevents an idealized treatment of the mine as a well that would be similar to a water well in a homogeneous aquifer having isotropic conditions. Yet, adherence to some principles of ground-water behavior is helpful when combined with an understanding of the local geology. A program calling for an appraisal of all pertinent hydrological conditions prior to mining and during various stages of development should supply adequate information for mine officials to anticipate difficulties and to allow for corrective measures. Before and during mining operations there should be a mine hydrology framework and plan, in which there is continual upgrading of such considerations as anticipated actions, consequences of actions, remedial plans, and contingencies.

Jan 1, 1973

The banquet Wednesday evening was attended by about 700. The list of speakers was unusually brilliant and each one proved to be so interesting that it was nearly midnight before the dancing began. Capt. Robert W. Hunt was toastmaster. Captain Hunt is about to celebrate his eighty-first birthday but is blest with unusual vigor and it was a great pleasure to all his friends to honor him at this time. His selection is toastmaster was a happy one. The guest of the evening, if among so many stars one could be selected from the rest, was Charles M. Schwab, who said nothing but the urgent telegram from his dear old friend, Captain Hunt, could have drawn him away from his seclusion on his Pennsylvania farm to attend the meeting in Chicago. Mr. Schwab's address was, as usual, scintillating with wit and humor; and while lie did not directly or indirectly allude to the steel strike lie did at the end of his talk discuss serious things and gave it as his opinion that any effort to legislate or control the high cost of living would be futile until this country got down to a basis of an honest day's work for an honest day's wage.

Jan 11, 1919

By H. K. Livingston

THE first person to investigate intensively the vast field of surface phenomena and capillary effects was the eminent English scientist, Lord Rayleigh (1842-1919), who laid down most of the fundamentals of this subject. This work was greatly amplified by Irving Langmuir,1 who, in connection with research for the General Electric Co., spent 25 years on the study of the surface chemistry of films, finally receiving the Nobel Prize in Chemistry for 1932 in recognition of his work. At present, William Harkins,2 of the University of Chicago, is the world's foremost authority on surface-tension measurement and his independent work, when combined with that of Langmuir, resulted in the orientation con-cept of solubility and surface activity, which is now an important funda-mental in chemistry. The theory laid down by these men was first applied to practical considerations regarding petroleum reservoirs by F. E. Bartell,3 of the University of Michigan, in connection with an American Petroleum Institute research grant. The latest and most advanced application of Bartell's work is contained in an article published in 1935 by Allen Garrison,4 of Rice Institute, in which he relates Bartell's measurements to the ratio of oil to water produced by wells and shows the types of petroleum reservoirs where the effects studied by Bartell are significant. This article is intended as a minor extension of such work.

Jan 1, 1938

By Kenneth E. Mathews, Ross D. Hammett, S. Byron Stewart

Theoretical models have been important throughout the history of engineering as a means of understanding past experiences and predicting future performance. Most modelling involves assumptions and a degree of idealization, and it is shown that it is important that the effects of these be recognized when making use of models. One of the principal concerns in underground mining is the effect of the excavations on the states of stress in the rock adjacent to these excavations. As mining proceeds to depth, stress concentrations may be sufficiently high to cause inelastic behaviour of the rock and yielding along joint surfaces. At this stage, attention must be given to the sequencing of the mining process to ensure that the ground control techniques applied are optimized. Increasing use is being made of computer modelling techniques to assist with design. Three case studies are presented to illustrate the application of computer models in mine planning and ground control. In all cases, the data available for design was limited, but the mines were fully developed and openings could be inspected. The mining methods studied are cut and fill stoping, room and pillar stoping, and longhole stoping.

Jan 1, 1983

By T. Nakao

Fujiwara quarry had been operated by the glory-hole benchcut mining system, but as it became difficult to meet expanding demand with this system, a central-shaft mobile crushing plant (MCP) system was introduced in 1979. This MCP is equipped with a hydraulic walking system manufactured for the first time in Japan. Central-shaft mining is now the common mining method of Japanese limestone quarries. With this method, crushing facilities are usually installed at the bottom of the shaft. But at the Fujiwara quarry, MCP was adopted and installed on the quarry surface. Many MCPs are operated in foreign countries, but few examples exist in Japan. Normally, Japanese limestone deposits lie in high mountain, obviously making it inconvenient for MCPs to walk in and around the quarry. This difficulty, however, was overcome, and the MCP has operated satisfactorily and efficiently for two years since its installation. To overcome difficulties in the central-shaft MCP mining system, two mining methods are employed: the slice-down method and the block-cut method.

Jan 1, 1985

By Leon Y. Sadler

Three new transfer functions relating the time response of the amount of floatable mineral in the under flow to time-dependent changes in the amount of floatable mineral in the feed to the cell are presented. Using experimental stimulus-response data obtained from the flotation of -200+325-mesh glass spheres in a rotor-stator-type cell, the new transfer functions are compared to the only transfer function to be presently found in the literature by nonlinear least-squares fitting in the frequency domain. The new mathematical model based on the amount of available bubble surface area and its rate of introduction is quite promising. The transfer function which allows for a distributed first-order flotation rate constant also gives good results. Simultaneous sodium chloride tracer and glass bead stimulus-response tests show that the mixing conditions in the cell were nearly ideal. It is felt that the new transfer functions presented offer excellent alternatives for use in the design of automatic process control equipment for the continuous mechanical froth flotation cell.

Jan 1, 1974

Jan 1, 1946

By R. Moldenke

Unlike the furnaces employed in the reduction of ores to mattes and metals, the foundry-cupola has only melting to do. This looks simple enough; and its development has progressed through centuries by cut-and-try methods; but there is still much to be learned concerning the causes which underlie the production of defective castings, even from first-rate materials. There are other differences between the smelter and the cupola. The former is usually, the latter rarely, run continuously. In the smelter there is some chance for experiment, since rich slags can be treated again; while in the cupola the metal must be good for casting from the first tap to the drop of the bottom ; otherwise, heavy damage will result. In the smelter, the object sought is the production of metal or matte with a minimum loss in the slag; whereas, in the foundry, a variety of castings of different compositions must often be run from the same heat, one after the other. Experience with the cupola has shown that the melting should take place, throughout the heat, in one zone, the zone of maximum temperature, which is clearly marked on the cupola-lining by the severe cutting action of the slag and iron oxide. The design and operation of the cupola must conform to this condition. This conformity having been secured, other considerations resolve themselves into those details of construction which will involve least trouble and cost of repairs. The very high temperatures required to melt iron and steel in the cupola, leaving the metal sufficiently superheated for casting, render the use of water-jackets inadvisable. It is always possible to patch up the lining at the melting-zone between daily heats; and the rest of the lining is seldom affected enough by abrasion and chemical action to require replacement oftener than once in nine months. The cupola is practically a shell of steel, lined with the proper refractory material, and provided with a sct of tuyeres for the admission of air to burn the fuel and melt the metallic

Jan 1, 1913

By H. M. Roche

MAGNETITE is the important iron ore of New Jersey although bog ore, limonite and red hematite were mined in sizable quantity early in the state's min-ing history. The deposits of mag-netite are found in the Highland area in the northern part of the state. These ores outcrop a broad belt 20 miles wide, extending in a northeasterly direction from Phil-lipsburg, on the Delaware River, to Greenwood Lake, at the southern boundary of the state of New York, a distance of 60 miles. The area in which the magnetite is found (see map, Fig. 1) contains 1200 square miles and the center of the area is at Dover, 40 miles west of New York City. In the general area are found 18 parallel ranges or lines of ore deposits. These ranges may be re-garded as mineralized zones in which occur orebodies that are rich enough in magnetite to war-rant mining. Usually a number of the orebodies lie one above the other in the same plane, all dipping and pitching in the same direction. Within the ranges, there may be several parallel orebodies of work-able size. The average strike of the orebodies is N.41° 30' E., with an average dip of 55° southeast and an average pitch of 15 ° to the northeast. Orebodies suitable for mining range from 6 to 100 ft. wide, as measured from foot wall to hanging wall. Their heights, as measured on the dip and normal to the long axis of the orebody, vary from 200 to 3,000 ft. The length along the pitch has never been determined by mining, al-though several of the orebodies have been worked to lengths of 10,000 ft. The grade of the ore as mined today varies from 30 to 60 per cent iron, and the gangue min-erals are chiefly silica, alumina, magnesia, lime and phosphorus.

Jan 1, 1937

By Charles Hart

THE art of electric smelting came with the turn of the present century and owes its existence to the introduction of alter-nating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N, Y. Prior to that time current was largely direct. The fur-naces were electrolytic in nature and found their first metallurgical use in the produc-tion of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific publications and books written during the first two decades of this century.

Jan 1, 1940

By AIME AIME

THE MILLING PROGRAM on Monday required a morning and afternoon session with a special luncheon of the Milling Committee in the Engineers Club at noon. Grinding and flotation were the main subjects of the papers which drew an attendance of fifty or more at each session. Under the direction of Chairman Arthur F. Taggart in the forenoon, all papers on flotation and general milling were considered, leaving the, after- noon free for crushing and grinding, with Dr. Galen H. Clevenger in the chair. The high spot was the first public presentation of the idea of size reduction of minerals by explosive shattering.

Jan 1, 1932

By George F. Becker

Complexity of Rock-Fractures.—The strains to which rocks have been subjected are manifestly very complex, and it is entirely safe to presume that every possible mode of deformation and rupture is exemplified. The most superficial inspection of any ordinary mountain region is sufficient to assure the observer that the rocks have been pressed, stretched, bent, buckled, twisted, and shorn. The study of torsional rupture cannot fail, therefore, to throw light on geological phenomena. The question is how areas which have been broken in this manner are to be distinguished from those which have yielded to other systems of forces. Phenomena of Joints.—It is well known that a large part of the more homogeneous rocks and some very heterogeneous rocks are intersected by partings often ailed joints. These partings are frequently flat surfaces even when seen in very large exposures, but are sometimes surfaces of moderate, single, or double curvature. Joint, usually occur in groups, in each of which the several partings are parallel to one another, and several such groups often intersect the same rock-mass. In such cases the different systems make large angles with one another. Nearly all students of the subject of jointing have reached the conclusion that joints are faulted surfaces, the dislocations usually being of small amplitude; and this conclusion receives abundant support from the study of thin sections under the microscope. It has thus been shown that much even of what would be regarded in hand specimens as mere slaty cleavage

Jan 1, 1895

Doctor David Yang has presented an important new flotation development in the area of fine particle flotation technology; at the same time Dr. Yang presents an explanation for the effectiveness of this improved new fine flotation system in terms of an optimum dispersion state. The same statement is made for the case of carrier flotation (ultraflotation), in the removal of anatase from kaolinite by addition of calcite (selective flocculation of the anatase - calcite system and dispersion of kaolinite). Dr. Yang's data and statements raise some important questions, and I will adress myself to the more fundamental aspects of this new flotation system. The addition of sodium silicate, well known as a good depressant-dispersant agent for siliceous gangue minerals, is proved to be greatly enhanced by the incorporation of polyvalent metal salts into sodium silicate prior to flotation, producing in this manner a condition, as described by Dr. Yang, of optimum dispersion, which in the case of fine-grained oxidized taconite can be described as selective flocculation (coagulation) of hematite and almost complete dispersion of siliceous gangue components. Dr. Yang recognizes that the main mechanism, while not completely understood at this time, seems to operate by modifying the surface characteristics of the gangue slime particles so as to prevent collector from bonding there to, and making the particles strongly hydrophilic so they will become fully dispersed and consequently will not float during froth flotation. At the same time it appears that the conditioning reagent also modified the surface characteristics of the floated minerals (hematite and spodumene in this case) so that they will aggregate and tend to more readily adsorb the collector, resulting in an improved flotation kinetics and selectivity.

Jan 1, 1979

By Persifor Frazer

It was my intention to have directed the attention of the members of the Institute to a complete series of rocks representing the older and middle formations represented in Pennsylvania, but time has been insufficient for the purpose, and 1 have been unable, in the first attempts to reduce the sections of those rocks, which I have brought with me to this meeting, to the requisite thinness necessary for exhibiting the peculiarities of their constituent minerals. The rocks represented here belong to the various horizons already mentioned, and include gneiss, ferruginous gneiss, chlorite slate, quartzites, and hydro-mica slates, limestones, dolomites, ferruginous conglomerates, quartz conglomerates, " Potomac marble" (nether member of the Mesozoic series), dolerites, and a syenite. The order in which these are named is, roughly, the order .of geographical position in a section line from southeast to northwest, commencing at the intersection of the Northern Central Railroad with the Maryland line, and ending a few miles from the town of York, and a short distance within the marginal outcrop of Mesozoic red sandstone. In such a geographical section all the rocks above mentioned would be encountered in the given order except syenite, about which a few words are to be said in a moment. (But this is far from representing the rocks in their geological sequence.) There is nothing of unusual interest to present to your notice in these slates and quarteites. The limestones were carefully searched tinder 450 diameters microscopic power, but they show no signs of organic remaius. One section of a fine-grained Triassic sandstone contains a very beau- . tifully banded plate of quartz. But the objects of greatest interest at present are the specimens of trap. The more fine-grained and compact traps were collected from

By John J. Theiler

Early in 1963, the Inspiration Consolidated Copper Co., at Inspiration, Ariz., began a program to make automatic the lubrication of several critical points on their KW Dart 37SL haulage trucks. Prior to installation of the automatic lubrication system, all the haulage trucks were serviced by hand every three shifts. Now, with automatic lubrication, the service period has been extended to four shifts. What are the principal benefits to be expected from such a system? 1) Uninterrupted production; 2) extended machinery life; 3) good housekeeping; 4) lower maintenance costs. Of these points, the most important to truck maintenance are extended component life and lower maintenance costs.

Jan 5, 1965

By H. A. Wilmeth

IN 1955, before planning an accelerated stripping program, Chino Mines Div. began an engineering study to improve data for estimating truck haulage costs for any future haulage layout. The study aimed to develop: 1) significant unit costs, 2) a method of estimating travel time from which truck needs and future stripping rate could be determined, and 3) yardsticks of performance to measure haulage efficiencies. It was suggested that to provide significant unit costs, expense accounts should offer management two types of cost control information-unit cost yardsticks with which monthly unit costs could be compared and unit costs for estimating future expenses for any haulage layout.

Jan 5, 1958

By M. P. Tixier, K. S. Kunz

A method for the interpretation of temperature curves recorded in gas producing wells is described. One essen-tial feature of the method is a simple graphical construction which conveniently reflects the amount of gas flowing from a given producing formation. This method, applied in conjunction with the Induction Log and radioactivity logs, is valuable to determine the points of entry of gas and to estimate the over-all thickness of the producing zones and their respective contributions to the total production. The method in particular is helpful in evaluating the effect of fracturing operations. An outstanding result of the application of the method is to bring to the light the relative importance of sand-shale interfaces in the production of gas. The paper is illustrated with field examp1es. INTRODUCTION The electrical logging tools involving conventional systems are not applied in wells which do not contain water base mud (empty holes, or wells filled with oil base mud), because of the absence of electrical connection between the electrodes and the surrounding formations. It is, therefore, common practice in this case to use other methods which do not require the presence of a conductive fluid in the borehole: resistivity log with scratcher electrodes, Induction Log, radioactivity logs, temperature log. . . . Such conditions are encountered in some regions, as the San Juan Basin, N. Mex., where a technique of drilling gas wells, using gas as a drilling fluid, has been introduced in the last two years. By the middle of 1953, an appropriate method for the logging of these wells was devised on the basis of field tests and of theoretical studies. It is the purpose of the present paper to give a description of this method. In these wells the logging operations are performed during the process of gas production, so that the temperatures in the boreholes are strongly affected by the cooling due to the expansion of the gas. On the other hand, a special thermometer, with a high sensivity and a short time constant, has been recently made available, which has enabled much more detailed and accurate recordings of the borehole temperatures than with the conventional instruments. As a result of these two circumstances, the temperature log constitutes the essential element of the method, in making possible the detection of the gas producing zones, the definition of their boundaries, and the estimation of the respective contributions of each separate zone to the total production. The method also involves the radioactivity and Induction Logs, as auxiliary documents. These logs in the present instance are helpful in the determination of the reservoirs. However, the information they give in this respect is limited. This comes from the fact that, due to the absence of the MicroLog and/or MicroLaterolog and of the SP log, the estimation of formation factors and connate water salinities is somewhat conjectural. Furthermore, little help is obtained from the Neutron log for the evaluation of porosity and of formation factor because the variations of gas saturation affect the Neutron log in a way similar to the variations of porosity. It should be said also that even an exact knowledge of the gas saturation of the reservoir beds would not

Jan 1, 1956

The Anglovaal Group has released details concerning its new processes for recovering platinum group metals, stating that the Group's system, which involves batch processing and precipitation methods for these metals (PGM's), leads to faster recovery times, increased recoveries, and higher purities than the conventional process. Insofar as South Africa's Merensky Reef is concerned, the Anglovaal method of recovering palladium first (as opposed to platinum in the conventional process) enables it to use a much simpler process in the subsequent recovery of platinum and other metals. Because the processes give cleaner separations, the volume of material to be recirculated -and therefore the total volume of material in the recovery circuits- is reduced substantially.

Jan 3, 1976