Search Documents

By C. O. Brawner

Simple, specific rules for achieving slope stability in open-pit mines are impossible to devise. Each pit has a different mining program and a different set of environmental conditions, and its final slope design must be based on an individual evaluation of the actual site. The overall philosophy of pit stability, however, is tending towards a limit design concept. Since slope angle has a great influence on the economics of most open-pit mines, efforts are being made to reduce the theoretical factor of safety for slope stability to very near 1.0. (Factor of safety is here defined as shear strength/shear stress on the most probable plane of failure.) Actually, where detailed, statistically significant testing has been done and a comprehensive ground control program is being instituted to warn of movement at an early stage, safety factors as low as 1.1 or 1.2 may be justified. The cost of the necessary procedures, however, is high. There are many factors that influence stability, but this article will be confined to three-rock structure, groundwater, and blasting.

Jan 8, 1969

By G. H. Walrod, J. M. Mutmansky, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to 1000 ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1979

By E. H. Wells, A. Andreas

The oil and gas industry of New Mexico recorded notable progress ill 1935. More wells were brought in than in any previous year, and important new discoveries were made. The total number of completions was 340, of which 260 were oil wells, 8 were gas wells and 72 were dry holes. The total oil production was 20,228,947 bbl., an appreciable increase over the 1934 production of 16,636,804 barrels. Many of the wells completed in southeastern New Mexico were acidized. This treatment proved highly effective in increasing the capacity of the wells, the resulting potentials usually being two to ten times as large as before acid treatment. In the Lea County fields in which proration was entirely on an acreage basis, the tendency of many of the operators was to complete their wells according to best conservation practice rather than to obtain the largest possible potential. Much remedial work was done in the Hobbs, Cooper, Jal and Eunice fields, and with excellent results. At many of the wells high gas-oil ratios were greatly reduced and encroaching waters shut off by setting packers. Several companies carried on pretentious geophysical campaigns in the southeastern part of the state. The location of the Amerada discovery well in the Monument field was based on geophysical surveys. The New Mexico Oil Conservation Commission, established by the 1935 Legislature and consisting of the Governor, the Commissioner of Public Lands and the State Geologist, began to function in May. Production in the state thereafter was based on orders issued by the Commission. Proration in the Hobbs field, which had been provided for since July, 1930, by successive proration agreements signed by all operators in the field and approved by the State Geologist, was continued by the Commission by giving approval to the current proration agreement,. A plan of proration for the other Lea County fields that had been in offect since early ill 1934 was adopted. 111 September, 1935, the Commission approved a. proration agreement for the Artesia-Jackson-Maljarnar area in Eddy and Lea counties that had been agreed upon by

Jan 1, 1936

By Frank E. Hall

The needs of the World War showed the necessity of a metal stronger than cast iron which would supplement the supply of steel. SO patriotic metallurgists were spurred to new efforts to improve the status of that half-breed of the metal world that had been, more or less erroneously, christened semisteel. As a result, it was developed that for certain purposes semisteel was superior to steel in the manufacture of shells. Steel, because of its greater strength and toughness, is able to carry a greater charge of explosive, weight for weight; consequently, a steel shell can be expected to cause greater destruction when used against fortifications or other inanimate objects, while semisteel, because of its comparative brittleness and its resulting greater fragmentation, is capable of inflicting more serious loss of life when used against opposing forces of men. Therefore, each has its proper place in the economy of war. For the present purpose, steel may be defined as a comparatively pure iron whose physical nature is modified by small amounts of carbon, silicon, sulfur, phosphorus, manganese, and possibly other rarer elements; while cast iron generally is limited to approximately 93 per cent. of iron, the remainder consisting of larger percentages of carbon, silicon, sulfur, phosphorus, and manganese. Semisteel may be defined as cast iron in which the carbon and silicon have been reduced to as low a point as is consistent with maintaining the nature of gray iron, and in which the remaining elements are adjusted so as to give the greatest strength. The fact that the addition of steel scrap, in varying percentages, is the means used to reduce the carbon, together with the fact that a considerable increase in strength results, is probably the explanation of the origin of the name semisteel. That ordinary grades of steel show from three to four times the tensile strength of cast iron is due to the fact that the crystals, or grains, of cast iron are interspersed with flakes of

Jan 1, 1922

By Frank E. Hall

The needs of the World War showed the necessity of a metal stronger than cast iron which would supplement the supply of steel. SO patriotic metallurgists were spurred to new efforts to improve the status of that half-breed of the metal world that had been, more or less erroneously, christened semisteel. As a result, it was developed that for certain purposes semisteel was superior to steel in the manufacture of shells. Steel, because of its greater strength and toughness, is able to carry a greater charge of explosive, weight for weight; consequently, a steel shell can be expected to cause greater destruction when used against fortifications or other inanimate objects, while semisteel, because of its comparative brittleness and its resulting greater fragmentation, is capable of inflicting more serious loss of life when used against opposing forces of men. Therefore, each has its proper place in the economy of war. For the present purpose, steel may be defined as a comparatively pure iron whose physical nature is modified by small amounts of carbon, silicon, sulfur, phosphorus, manganese, and possibly other rarer elements; while cast iron generally is limited to approximately 93 per cent. of iron, the remainder consisting of larger percentages of carbon, silicon, sulfur, phosphorus, and manganese. Semisteel may be defined as cast iron in which the carbon and silicon have been reduced to as low a point as is consistent with maintaining the nature of gray iron, and in which the remaining elements are adjusted so as to give the greatest strength. The fact that the addition of steel scrap, in varying percentages, is the means used to reduce the carbon, together with the fact that a considerable increase in strength results, is probably the explanation of the origin of the name semisteel. That ordinary grades of steel show from three to four times the tensile strength of cast iron is due to the fact that the crystals, or grains, of cast iron are interspersed with flakes of

Jan 1, 1922

Jan 1, 1946

By D. K. Atwood

Experiments resulted in a satisfactory laboratory method for restoring permeability to clay-containing cores damaged by fresh water. Clay contents of a number of field cores were measured, and permeabilities of plugs from these same cores were then deliberately reduced with fresh water. This damage is attributed to swollen and dispersed clays occupying the pore space. After damaging, a number of experiments were performed to meaJure the amount of damage and to establish some means by which permeability could be restored. The experiments included flooding the damaged cores with water-miscible fluids such as salt water, acetone, isopropyl alcohol and ethanol. Permeability was not successfully restored in these experiments. However, part of the damage was repaired by flooding with oil; when water was removed by distillation in the presence of immiscible fluids such as air or toluene, permeability was completely restored. This evidence suggested that swollen and dispersed clays could be collapsed to their original volume by strong interfacial and capillary forces. It was further postulated that the required forces could be generated by flooding the damaged cores with a solvent partially miscible with water. The flooding experiments were repeated using n-hex-an01 as the partially miscible solvent. Permeability was restored to five of six damaged cores and substantially increased in the sixth. A large fraction of the restored permeability was retained even after water saturation was raised to its original value with 12 per cent salt water. INTRODUCTION Sharp reductions in permeability often occur when relatively fresh water contacts clay-containing formations during drilling and workover operations. These permeability losses are caused by removing inorganic ions from the environment surrounding the clay, and consequent swelling and/or dispersion of clay minerals into the available pore space.' This phenomenon is generally termed clay damage, fresh-water damage, or simply formation damage; it causes large losses in current revenue by preventing oil wells from making their allowable production. Attempts to repair the damage and restore permeability by flowing salt water solutions or brines through clay-damaged cores containing montmorillonite have been unsuccessful.' This irreversibility is thought to result from formation of brush-heap, or edge-to-face, structures when the dispersed clay is flocculated. The brush-heap structures occupy much more space than the close packed domains present before damage.' One solution of the problem is to destroy the clay-water brush-heap and thus restore permeability. Because no satisfactory method existed for restoring permeability to clay-containing formations damaged by fresh water, the work described in this paper was under taken. The laboratory experiments generally consisted of deliberately damaging fresh cores containing clay and then attempting to repair this damage by various means. Results indicate that generating strong interfacial forces within the pore space of damaged cores collapses the clay brush-heap and restores permeability. These forces are most conveniently generated by flowing partially water-miscible solvents, such as n-hexanol, through a core. THEORY OF THE DAMAGE PROCESS The most common clay mineral groups known to cause permeability damage to formations are the mont-morillonites, kaolins, chlorites and illites. These clays are constructed of particles which can adsorb water on their surfaces and edges and, in the case of montmorillonite, between layers of the basic particle itself. This adsorption increases as water salinity decreases. At low salinities the particles disperse into the aqueous phase. When the clays present in the formation are kaolin, chlorite and illite, dispersion accounts completely for permeability damage to porous media. However, unlike the other clays, montmorillonite particles can imbibe water and adsorb ions between layers of sub-particles, or platelets. These platelets have net negative charges on their faces and are held together by exchangeable (or removable) cations such as Na and Ca decrease in ion concentration (salinity) in the fluid surrounding a particle causes migration of water into the clay layers and disperses the basic particle, while diffusion removes the original exchangeable ions from between the platelets. Once these ions are removed, the facing negative platelets repel each other, causing the montmorillonite to swell until, for all practical purposes, the individual platelets are dispersed. For this reason, fresh-water* damage is much more severe in sands containing montmorillonite than it is in sands containing other clays. Many investigators have shown that even trace amounts of montmorillonite can be responsible for marked reduction in the permeability of reservoir sands in the presence of fresh water." ." Monaghan and others have shown that fresh-water damage in montmorillonite-containing cores cannot be

Jan 1, 1965

By T. MacDONALD

ATHOUGH flotation has been a commercial process for over twenty years, the last two years have witnessed a sudden and phenomenal increase in our knowledge of how to separate minerals heretofore not considered amenable to flotation at all. As remarked by Professor Locke in the January issue. "Either commercial or laboratory flotation is reported on zircon, ilmenite, carnotite, kyanite, scheelite, chromite, fluorite, feldspar, cassiterite, wolframite, barite, and clay. Attractive patents on soap flotation are U. S. Nos. 2,000,656 and 2,040.187. A survey by Ralston in the February E. & M. J. adds many other minerals to this impressive list. The simple but pregnant fact is that any mineral can be coated, directly or indirectly, with a water-repellent coating, and since this is true, it follows that any mineral can be floated. Fundamentally, this is no new discovery, where, for instance, is the mineral that cannot he washed from a pair of dirty hands by means of soap and water, given the absence of refractory greases or oils which would have no proper place in flotation ?

Jan 1, 1937

By W. Petruk, R. S. Boorman, R. Gilders

Approximately 33% of the silver in the Zn-Pb-Cu-Ag ore of Brunswick Mining and Smelting Corporation Limited is lost to the tailings and an additional 11% to the zinc concentrate for which no payment is received. 38% to 44% of this lost silver is carried by tetrahedrite, 28% by galena and 28% to 34% by a third silver carrier. The silver minerals acanthite and pyrargyrite have been identified in mill products and hence these are suggested as the principal third silver carrier(s) accounting for 13 to 20% of the silver in Brunswick ore. About 24% of this third silver carrier assemblage is lost to the zinc concentrate and 52% to concentrator tailings.

Jan 1, 1984

By Douglas M. Dwosh

Inland Steel Coal Co.'s system of applying a gypsum/fiberglass rib and roof sealant with standard rock dusting equipment will be outlined. The criteria for use included acceptability of results, flexibility of equipment, ease of application, and economics. Material is conveyed dry until the gypsum, fiberglass, and water are combined at the discharge end of the rock dust hose.

Jan 1, 1978

Jan 1, 1917

By V. K. Karra, A. J. Magerowski

An overview of the scope of a computer program meant for aiding the design of crushing circuits is presented. Effect of circuit variables like the screen separation size and the crusher setting is illustrated. For a better understanding of the logic behind the circuit sizing, a detailed commentary in the case of a starting example is given.

Jan 1, 1982

By G. K. Burgess

G. K. BURGESS* and R. W. WOODWARD,? Washington, D. C.-From a metallurgical standpoint, there are several ways in which a reduction of the tin consumed in commercial non-ferrous and white-metal alloys can be effected. First, a reduction of the tin, content of the alloy; second, substitution of part or all of the tin content by some other metal; third, a substitution of a different type of alloy, which in some cases also involves a change in mechanical design. The Bureau of Standards has been studying these methods of conservation for tin alloys, particularly in regard to babbitts and bearing metals, bronzes, and solders. Much of the information secured by the Bureau was obtained from answers to questionnaires sent to manufacturers and users of these materials, so that, in general, any of the following suggestions or recommendations can be considered as being practical and as having already been thoroughly tried. Bearing Metals There is no question that the tin content of nearly all bearing metals can be reduced to some extent, and in some cases actually eliminated

Jan 12, 1918

By M. J. Sinnott, W. R. Kiessel

The creep characteristics of commercially pure titanium sheet in the annealed state, cold-worked state, and cold-worked and recovered state in the temperature range from 75' to 750°F have been determined. Titanium has been found to exhibit strain aging characteristics. The effect of strain aging on creep has been determined. A possible explanation for the poor creep properties of titanium is proposed. THE metal titanium exhibits many desirable properties but results on its creep properties have been somewhat disappointing. The creep strength is low even though the material has a very high melting point.' The present work was undertaken to determine the creep strength of titanium in various conditions; annealed, cold-worked, and cold-worked and recovered and to determine why titanium shows such relatively poor creep properties. The general procedure followed in this research consisted in obtaining the usual mechanical prop- erties such as creep strength, short time tensile strengths, and hardness on materials treated to a controlled degree of internal strain, as determined by X-ray diffraction measurements, and their subsequent interpretation in terms of this internal strain. The material used in this work was sheet stock taken from one heat of commercially pure titanium. As-received, this sheet was 0.060 in. thick. The analysis was given as 0.037 pet C, 0.023 pet Si, 0.50 pct W, 0.063 pct Ni, 0.08 pct Fe, and the remainder titanium. The oxygen and nitrogen were unreported but generally are about 0.2 pct in commercial heats. In order to put the material in a state of minimum internal strain all the sheet was given an anneal in a static argon atmosphere for 1 hr at 1600°F prior to processing and testing. The microstructure of the material after this treatment was essentially a single-phase solid solution of uniform equiaxed grains. For the studies on the cold-worked sheet, the material was reduced by rolling in a two high, 5 in. mill. Rolling was done at room temperature in passes

Jan 1, 1954

By J. T. Eash, E. M. Wise

Many of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. Scope and Conclusions Tensile tests were carried out at room temperature and elevated temperatures up to 1100" C. on previously well annealed samples of platinum. palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100" C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested. The tensile strengths of palladium and the palladium alloy at 1100" C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at temperatures above 600" to 800" C., while the two samples of pure palladium show a maximum at 600" C.

Jan 1, 1938

By J. T. Eash, E. M. Wise

Many of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. Scope and Conclusions Tensile tests were carried out at room temperature and elevated temperatures up to 1100" C. on previously well annealed samples of platinum. palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100" C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested. The tensile strengths of palladium and the palladium alloy at 1100" C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at temperatures above 600" to 800" C., while the two samples of pure palladium show a maximum at 600" C.

Jan 1, 1938

By James Pollock

The possibility of colloidal deposition of cinnabar has been neglected. In opalite deposits cinnabar exists in particles within or near the colloidal size range. Colloidal processes have been admitted to be operative in hot springs and low-temperature deposits similar to most cinnabar deposits. Mercuric sulphide sols are stable to elevated temperature and pressure, and in nature probably are chiefly affected by the electrolytes in solution, dilution of colloid, and presence of protective colloids as silica. The stability of mercuric sulphide sols to electrolyte is measured, and shown to be greatly increased by dilution and by the protective action of silica. Mercuric sulphide sols follow the Schulze-Hardy valency rule, therefore the precipitating power of complex mixtures of electrolytes can be computed roughly. The stability of mercuric sulphide sols is shown to be greater than the equivalent precipitating power of the electrolytes in a hot spring depositing mercuric sulphide. It is concluded that finely divided or earthy types of cinnabar are colloidally deposited. Possibility of Collodial Deposition While colloidal solution has been suggested as a means of transport for a number of minerals, such as the sulphides of antimony, arsenic, and iron, it has been neglected in connection with mercury. This is surprising because there exists positive evidence that cinnabar is present in certain deposits in particles of colloidal or near colloidal size. Colloidal transport could result from either the rapid dilution or neutralization of alkaline sulphide solution bearing mercury coming in contact with deep ground waters, or from colloidal solution near the original source and subsequent flow to the point of deposition unchanged. That the dilution of a mercuric alkaline sulphide solution will precipitate mercury sulphide in colloidal form has been demonstrated a number of times and is easily confirmed. The dilution hydrolyzes the alkaline sulphide Na2S to the corresponding hydroxide and hydrosulphide NaOH and NaHS, and the diminution of the concentration of alkaline sulphide reduces the solubility. It is not the contention of this writer that colloidal deposition is the mode of transport of mercuric sulphide in all mercury deposits, but that the stability of a mercuric sulphide sol, as demonstrated below, in waters that are similar to those that have deposited mercuric sulphide necessitates consideration of this possibility in many deposits, especially those of the hot-spring and so-called opalite type. Evidence of Colloidal Deposition Ross1 has shown that most deposits of quicksilver are formed at low temperatures and pressures, and probably by solutions that have relatively simple chemical compositions. In most cases the solutions are probably similar to those observed in hot springs, and in two instances—at Steamboat Springs, Nevada, and Sulphur Bank, California—hot springs have been reported by Becker as actually depositing cinnabar.2 Opalite deposits were believed by early investigators to be surface phenomena

Jan 1, 1949

By James Pollock

The possibility of colloidal deposition of cinnabar has been neglected. In opalite deposits cinnabar exists in particles within or near the colloidal size range. Colloidal processes have been admitted to be operative in hot springs and low-temperature deposits similar to most cinnabar deposits. Mercuric sulphide sols are stable to elevated temperature and pressure, and in nature probably are chiefly affected by the electrolytes in solution, dilution of colloid, and presence of protective colloids as silica. The stability of mercuric sulphide sols to electrolyte is measured, and shown to be greatly increased by dilution and by the protective action of silica. Mercuric sulphide sols follow the Schulze-Hardy valency rule, therefore the precipitating power of complex mixtures of electrolytes can be computed roughly. The stability of mercuric sulphide sols is shown to be greater than the equivalent precipitating power of the electrolytes in a hot spring depositing mercuric sulphide. It is concluded that finely divided or earthy types of cinnabar are colloidally deposited. Possibility of Collodial Deposition While colloidal solution has been suggested as a means of transport for a number of minerals, such as the sulphides of antimony, arsenic, and iron, it has been neglected in connection with mercury. This is surprising because there exists positive evidence that cinnabar is present in certain deposits in particles of colloidal or near colloidal size. Colloidal transport could result from either the rapid dilution or neutralization of alkaline sulphide solution bearing mercury coming in contact with deep ground waters, or from colloidal solution near the original source and subsequent flow to the point of deposition unchanged. That the dilution of a mercuric alkaline sulphide solution will precipitate mercury sulphide in colloidal form has been demonstrated a number of times and is easily confirmed. The dilution hydrolyzes the alkaline sulphide Na2S to the corresponding hydroxide and hydrosulphide NaOH and NaHS, and the diminution of the concentration of alkaline sulphide reduces the solubility. It is not the contention of this writer that colloidal deposition is the mode of transport of mercuric sulphide in all mercury deposits, but that the stability of a mercuric sulphide sol, as demonstrated below, in waters that are similar to those that have deposited mercuric sulphide necessitates consideration of this possibility in many deposits, especially those of the hot-spring and so-called opalite type. Evidence of Colloidal Deposition Ross1 has shown that most deposits of quicksilver are formed at low temperatures and pressures, and probably by solutions that have relatively simple chemical compositions. In most cases the solutions are probably similar to those observed in hot springs, and in two instances—at Steamboat Springs, Nevada, and Sulphur Bank, California—hot springs have been reported by Becker as actually depositing cinnabar.2 Opalite deposits were believed by early investigators to be surface phenomena

Jan 1, 1949

By J. R. Hassemer, T. T. Chao, University of Georgia, K. C. Watts, R. F. Sanzolone

Secondary oxides of Fe-Mn have been used in mineral exploration from the time gossans were first recognized Since gossans are conspicuous features and are largely explored, it is necessary to look for more subtle indication of blind mineralization. Sampling materials used in these geochemical studies consist of secondary Fe-Mn oxide-rich products of hydrothermal mineralization, and "in situ" weathering found in fracture fillings-as selvages along joints and disseminations in host rock. These materials were selectively collected and studied in the Silver City mining region. Two independent sampling methods were compared. The difference in the sampling methods was mainly in the ways samples were obtained and processed. One method involved systematic sampling of fracture fillings and coatings from which secondary Fe and Mn oxides and associated trace elements were then selectively extracted by chemical methods. The second approach involved collection of composite stream sediments and physical extraction of Fe-Mn oxide materials by gold panning, bromoform concentration, and electromagnetic separation. The source of the Fe-Mn-rich materials in the stream sediments is considered to be fracture fillings and coatings that mechanically entered the drainage basins. Map distributions of the two-sample types were compared. Both methods showed generally supportive patterns of anomalous metal dispersion, although anomaly-to-background contrast seems better in joint coatings. Both were useful in distinguishing geochemical differences between mining districts in the region. For example, the Pinos Altos district may contain more hydrothermally-introduced iron than the Central district, whereas the Central district has lead and zinc enrichments that are less on the amount of iron enrichment than is the case in the Pinos Altos district. The methods were qualitatively compared relative to time, expense, and other advantages and disadvantages.

Jan 1, 1984

By J. S. Johnson, W. C. McCulloch

ALL phases of plant operation must be synchronized so that the number of interruptions in the flow of material may be reduced to a minimum. In the majority of plants operating under a labor agreement, time lost during the operating shift cannot be made up with overtime. With the work week restricted to 35 hr., the ratio of productive time to total time justifies extra effort in keeping the plant operating at capacity during the productive shift. This does not apply when central plants with adequate storage are operated by multiple shifts. In such installations the problems become similar to those of any factory or mill where added units parallel circuits, or excess capacity serve to maintain the average production during intervals of maintenance shutdown. These plants, by special agreement, may run continuously, barring mechanical interruptions. The control of plant operation is in those procedures that are practiced to obtain from the run-of-mine product a high recovery of clean coal products to meet adopted trade standards and consumer specifications at the lowest possible cost. Correlation of all factors for continuous operation requires more than mechanical perfection in the plant. The run-of-mine coal must be delivered to the preparation plant without delays and the clean coal and refuse products taken away. Power supply and water requirements must be adequate. Signal systems must be established for emergency stops and to facilitate resumption of coal flow. ORGANIZATION Probably the most important item for successful operation of a preparation plant is a capable organization interconnected with the mine organization. A typical organization chart for companies operating in the Pennsylvania anthracite region is shown in Fig. 1. The breaker foreman is in direct contact with the plant preparation operation and reports to the outside foreman, who, in turn, reports to

Jan 1, 1943