Search Documents

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

E. T. Dumble, Houston, Texas (communication to the Secretary) : During the field-season of 1890 I had occasion to examine some of the salines of eastern Texas. As the result of my stridy of them I came to the conclusion that, together with the oil of Hardin county (since extended to Beaumont by the work of Capt. Lucas) and the rock-salt and gypsum-deposits of the coast country, extending southward to the Rio Grande, these were simply a continuation of similar deposits in Louisiana described by Hilgard, Hopkins, and others; and I recommended the sinking of wells wberever they were found.

Jan 1, 1902

By Niels Hansen

The substructure formed by drawing at room temperature in aluminum (99.5 and 99.998 pct purity) and in recrystallized aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum -oxide was examined by transmission electron microscopy, and the flow stress of the drawn materials was measured by tensile testing at room temperature. A sub-grain structure was present after a reduction in area by drawing of 10 to 20 pct, and the subgrain size was observed to decrease with increasing deformation. The tensile data show that the increase in flow stress (0.2 pct offset) by drawing from 10 to 95 pct depends on the reduction in area, not on the composition of the materials. Dispersion strengthening and subgrain bowzdary strengtlzening contribute to the flow stress, and these strengthening processes have been found to be linearly additive. The flow stress (0) can be related to the subgrain size &) by the Petclz relation = uo + k . t, where go is dependent on the composition of the products and k is approximately the same far all materials. THE microstructure of dispersion-strengthened aluminum aluminum-oxide products consists of small oxide plates distributed in an aluminum matrix. The matrix structure depends on the manufacturing history, and in hot-worked as well as cold-worked products the matrix is divided by subgrain (or dislocation) boundaries. For hot-extruded products it has been shown1 that dispersion strengthening and subgrain boundary strengthening are linearly additive, and the flow stress (0.2 pct offset.) at room temperature has been related to the subgrain size (ts) by a Petch equation,2,3 s = so + k . ts-1/2, where s0, increases with increasing oxide content. For cold-worked products containing subgrains no systematic work has been reported, and it was the aim of the present study to examine the microstructure and the relationship between the flow stress and the subgrain size for such products. The behavior of' aluminum aluminum-oxide products depends on the purity of the aluminum matrix, and aluminum of the matrix purity (99.5 pct) was included in the investigation. The literature contains few data about the behavior of this impure aluminum, and aluminum of a higher purity (99.998 pct) was therefore also examined. As regards the relationship between the flow stress and the subgrain size in cold-worked dispersion-strengthened products, no systematic work has been reported. For aged cold-worked structures containing fine precipitates (Fe-Mo carbide) a Petch relation has been found,4 and it has been shown that the k value NlELS HANSEN is Head, Metallurgy Department, Danish Atomic Energy Commission, Research Establishment Riso, Denmark. Manuscriot submitted January 9, 1969. IMD is approximately the same as in iron, whereas the s0 value is higher owing to the presence of the precipi-tates. Investigations of metals such as tungsten,' ferrous metals,4,6 and molybdenum7 cold drawn or swaged at room temperature have shown that the flow stress can be related to the subgrain size by a Petch relation when ts is taken as the subgrain size perpendicular to the direction of deformation. For aluminum no work has been reported on the relationship between the flow stress and the subgrain size after deformation at room temperature, whereas for aluminum tensile strained at different temperatures in the range -183" to 375°C a Petch relation has been found by taking ts equal to the subgrain size.' In the present study two aluminum materials (99.998 and 99.5 pct) and three aluminum aluminum-oxide products (containing 0.2, 1.0, and 4.7 wt pct oxide) were drawn at room temperature to reductions in area from about 10 to about 95 pct. The structures were studied by transmission electron microscopy, and the flow stress (0.2 pct offset) was measured at room temperature. EXPERIMENTAL Materials. The materials are given in Table I together with the chemical analysis. The three aluminum aluminum-oxide products were manufactured from aluminum powder that had been compacted and Table I. Chemical Analysis of Materials Al203 Fe SI Material wt pct wt pct wt pct 99.998 pct* - 0.0004 0.0012 Aluminum 99.5 pctt - 0.36 0.16 Aluminum AlMD13† 0.2 0.16 0.12 Aluminum- -Oxide AlMD105† 1.0 0.26 0.18 Products SAPISML960s† 4.7 0.22 0.19 *Other impurities: O.0004 pct max each of Cu and Zn (supplier's analysis). †Other impurities: 0.03 pct max Cu. 0.02 pct max each of Mn, Mg, Zn, Ti. Table 11. Mean Diameter of Aluminum-Oxide Particles in Extruded and in Cold--Drawn Aluminum Aluminum-Oxide Products Mean Diam. of A1203-Plates* Material State A AlMD105 Extruded 540 Cold Drawn 97 pct 510 SAP ISML 960 Extruded 770 Cold Drawn 95 pct 820 *The standard deviation of the mean is approx. 5 ±pct.

Jan 1, 1970

By J. E. Flinn, S. A. Duran

The steady-state creep behavior of poly crystalline cad mi inn was studied over a temperature range of (1.56 to 0.94 Tm. Two distinct mechanisms were found to occur over this temperature range. They were described by: where and represerqt the minimum strain rates corresponding to the low- and high-temperature regions, respectirely. The two regions of constant acti11ation energy were connected by a transition region where the strain rate was controlled by both mechanisms acting in parallel. At temperatures below a transition temperature of about 0.7 Tm the agreement between the activation energy value for creep and that for self-diffiision suggests a rate-controlling mechanism of dislocation climb. For cadwzium, steady-state creep at temperatures above 0. 7 Tm appears to be controlled by another mechanism, perhaps involving the behavior of dislocation jogs. FRENKEL et al.1 studied the high-temperature creep of polycrystalline cadmium and reported an activation energy of 21 kcal per mole for the 0.5 Tm < T < 0.8 Tm range. Based on observations of creep rate at only two temperatures, a value of 22.1 kcal per mole was determined by Medbury. These two investigations were for the purpose of showing agreement between the activation energy for creep and that for self-diffusion, reported3 as 18.2 and 19.1 kcal per mole, respectively, for diffusion parallel and perpendicular to the hexagonal axis. Gilman4 investigated prismatic glide in single crystals of cadmium over a higher-temperature range of 0.72 to 0.93 Tm, and found an activation energy of 29 kcal per mole. He also reported5 an activation energy higher than that of self-diffusion for prismatic glide in zinc single crystals deformed at temperatures near the melting point. This value was in good agreement with those found for an equivalent temperature range by Flinn and Munson6 and by Tegart and sherby7 for polycrystalline zinc. These two independent studies also disclosed at lower temperatures another value of activation energy near that for self-diffusion. It would be expected from the creep results on zinc and single-crystal cadmium that creep studies on polycrystalline cadmium, extended to temperatures near the melting point, might yield an activation-energy value higher than the 22 kcal per mole value found in earlier studies. The purpose of this paper is to report the steady-creep behavior of polycrystalline cadmium over a temperature range of approximately 0.5 to 0.9 Tm EXPERIMENTAL METHOD The cadmium used in this study was obtained in the form of as-cast rods, 0.5 in. diam, through the courtesy of the Bunker Hill Mining Co. The material was of 99.995 pct purity, as determined by spectro-chemical analysis. The creep specimens, which were 0.250 in. diam by 0.400 in. long and annealed at 300°C for 45 min to produce a stable average grain diameter 0.25 mm, were tested in compression using an apparatus similar to that described by Sherby.8 The specimen temperature was controlled to within ±0.5°C with the help of appropriate constant-temperature baths. The applied stress was maintained within 1.0 pct of the desired value by the additions of lead shot at fixed strain increments. No barreling was observed over the strains encountered during testing. Isothermal creep tests9 were used in the study with only a few differential temperature tests10 run for comparison purposes. Steady-state creep data were obtained over a temperature range of 60 to 287°C (0.56 to 0.94 Tm) at five stress levels ranging from 28.1 to 140.6 kg per sq cm. RESULTS The minimum or steady-state creep rate may be described by an equation of the following form:" where i is the minimum strain rate, S is the structure factor, F is a stress function, Qc is the energy of activation, T is the absolute temperature, and R is the gas constant. The minimum strain rates obtained in this study for cadmium were recorded on a semilogarithm plot as a function of the reciprocal absolute temperatures for the various stress levels, as shown in Fig. 1. This figure shows a characteristic transitional behavior" with a parallel interaction of two mechanisms. It is obvious that the activation energies corresponding to the individual processes are insensitive to stress because the curves are parallel. The discrete activation-energies values for the low- and high-temperature regions for the various stress levels are reported in Table I, and were determined by the least-mean-square method. For the low-temperature region, an activation energy of 20.7 ± 0.6 kcal per mole was obtained, and for the

Jan 1, 1967

By M. Mortada

Nonsteady-state flow of slightly compressible liquids in porous media of non-uniform properties has been the subject of a number of recent studies. Most of these studies considered one-dimensional flow in systems with cylindrical geometry and with the properties of the porous medium varying with radial distance only. A. Houpeurt&apos; studied the problem in its general form by examining the solutions of the differential equation, In Eq. 1, the permeability k and the porosity + are arbitrary functions of radial distance. Houpeurt concluded that, except for special forms of the functions k and the problem is not well suited for mathematical treatment, but lends itself to high-speed digital computation. Carslaw and Jaeger&apos; discussed the solution of Eq. 1 for the case in which the permeability varies as a power of the radial distance. P. Albert3 studied analytically the pseudo steady-state solutions in systems of finite radial extent and non-uniform properties. He also obtained some numerical solutions for nonsteady-state flow using a high-speed computer. William Hurst4 examined the interference pressure drop due to a point sink located in an infinite system consisting of two permeability regions in series. In this case, the permeability changed at a radial distance r from the point sink. INTERFERENCE BETWEEN OIL FIELDS IN A NON-UNIFORM AQUIFER The interference pressure drop for oil fields located in an extensive aquifer of uniform properties is discussed in a number of places in the literature. This work considers the interference pressure drop for oil fields located in a non-uniform extensive aquifer comprising two regions of different properties as shown in Fig. 1. Region I of the aquifer extends from which is the radius of Oil Field A, to ar,,, where a>1. It has permeability k,, porosity +, and effective compressibility c,. Oil Field B is located in Region II which extends from ar, to infinity and has different properties from those of Region I, but the same formation thickness h. Region II has permeability k2, porosity and effective compressibility c2. The choice of this type of aquifer should not imply that it is of frequent occurrence. It is chosen primarily to illustrate the effects of non-uniform aquifer properties on oilfield interference. It is of interest to point out that a non-uniform radial aquifer in which both the permeability and the porosity are inversely proportional to the radial distance can be treated in a manner similar to a linear aquifer of uniform properties. The situation where only the permeability varies as the inverse of the radial distance is also amenable to analytical treatment. Both aquifers behave quite differently from a radial aquifer with uniform properties so far as the water influx and the interference pressure drop are concerned. METHOD OF SOLUTION The expression for the interference pressure drop in Oil Field B due to a constant rate of water influx in Oil Field A is developed in the Appendix. This is accomplished by the simultaneous solution of two partial differential equations describing the pressure in Regions I and 11. The two differential equations are solved subject to the following conditions: (1) at r,, the pressure gradient is constant; (2) at ar the pressure and

By R. B. BRINSJIADE

THE following is an attempt to form a formula by which a mine call be quickly evaluated, after all pertinent physical data have been collected from observations on the ground by a competent mining engineer. ASSUMPTIONS. Let G = price to be paid for the mining property. M = cost of developing the mining property to yield y tons of ore daily. P = cost of suitable plant to treat y tons of ore daily. p = value of said plant when the mine has.been exhausted. C = total fixed capital investment. W = working capital investment

Jan 1, 1908

By AIME AIME

TO THE AMERICAN MINING CONGRESS. AMERICAN INSTITUTE OE MINING ENGINEERS. MINING AND METALLURGICAL SOCIETY OF AMERICA. The committee that makes this report was appointed at the meeting of the American Mining Congress, at Denver, Colo., in. November, 1906. The appointment had in view the drafting. of a law for the regulation of quarrying and metalliferous mining under the police laws of the States, with the hope that the uniform adoption of such a law could tend to reduce the number of accidents in mining. Since its. appointment, the committee has had&apos; under serious and continuous consideration the matter with which it was charged. At the meetings 0f the American Mining Congress in 19o7, 1908 and 1909, it reported progress. At the meeting in 1909 it was authorized to present its report not only to the American Mining Congress, but also to the American Institute of Mining Engineers and the. Mining and Metallurgical Society of America, and to present its report in printed form during the interim between meetings of the American Mining Congress. The committee collected from the officials of the States of the Union copies of their mining laws. With the assistance of the Engineering and Mining Journal copies of the laws 0f Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New aland, and certain European countries were also obtained. These laws were subjected to careful study. The first publication of the committee was a summary of the more important metalliferous mining laws 0f this country. Upon the basis of the existing laws of the States of the Union, Great Britain, and the English speaking colonies, a tentative draft. was prepared and printed in limited number in 1909, for convenience in securing the advice and criticism of a considerable number 0f persons engaged in the mining industry. In this way valuable suggestions were received. At the request of the chairman of this committee, Mr. Frederick L. Hoffman, statistician of the Prudential Insurance Company, of Newark, N. J., summarized and reviewed the available statistics of fatalities in metalliferous mining in the United States. Mr. Hoffman&apos;s report was published in the Engineering and Mining

Jan 10, 1910

By John W. Wagner, Robert K. Willardson

Single crystals of Pbl-xSnXTe have been grown from The melt under liquid B2O3 using the Czochralski technique. The PbTe-SnTe crystals were grown from near-stoichiometric melts and from melts with slight deviations from sloichiometry. Crystal growth rates ranging from 1 mm per hr to 1 cm per hr were employed, the latter being generally used. Several investigations were performed to characterize the single crystals grown In this study. The phase diagram of the PbTe-SnTe system was examined. X-ray analyses verified the single-crystal character of the crystals, and powder pattern lattice parameter determinations showed that Vegard&apos;s law was followed within the limits of the experimental error. The as-grown crystals were p-type with apparent carrier concentrations of -8 x 1018 to -8 x 1020 carriers per cu cm. Hall coefficients, resistivities, and carrier mobilities were determined as a function of composition. Dislocations were revealed by an electrolytic etch, and the crystals were found typically to contain 2 to 4 x 105 dislocations per sq cm. Microhardness measurements were performed; no maximum in the Vickers hardness us composition curve was seen. Mass spectrometry was used for impurity analyses, and the crystals were found to contain 1 to 2 x 1017 total p-type impurities per cubic centimeter. Distribution coefficients were calculated for the major impurities which were Na, Mg, Al, Si, Cl, and Zn. RECENTLY interest has been stimulated in the preparation and characterization of many alloys of the binary compound semiconductors. This interest is due primarily to the almost unlimited possibilities of adjusting the semiconducting characteristics of these materials by varying the alloy compositions. One alloy system which has been receiving extensive investigation is the PbTe-SnTe system, since these alloys show promise of being useful as emitters and detectors of electromagnetic radiation in the spectral range of 8 to 14 µ. This paper reports on the growth of PbTe-SnTe single crystals by the Czochralski technique and investigations of the general properties of these crystals. The phase diagram of the PbTe-SnTe system was investigated so that specific alloy compositions could be attained. I) CRYSTAL GROWTH The PbTe-SnTe single crystals were pulled from the melt using the Czochralski technique. Generally, the crystals were grown from near-stoichiometric melts, although special growth runs were made from both lead-rich and tellurium-rich melts. Growth of single crystals from up to 5 pct lead-rich melts presented no problems; however, melts with tellurium in excess of -1 pct caused volatilization problems which generally made crystal growth impossible. All melts were prepared from high-purity materials as follows: 1) lead— 6 N— Cominco (Cominco Products, Inc., Spokane, Wash.); 2) tin—5N—Cominco; and 3) tellurium— 5N+— American Smelting & Refining Co., Plainfield, N.J. No further purification of materials was undertaken in this study. The elements were reacted at -1000°C in a vacuum-sealed silica tube for a few hours, a gentle rocking action being used to ensure thorough reaction. The cast ingots were then transferred to a silica crucible for crystal growth. A schematic diagram of the growth apparatus is shown in Fig. 1. The Vycor tube is sealed at both ends by O-ring flanges so that a vacuum or a positive pressure may be maintained in the growth chamber. The pull rod and crucible may be rotated; all crystals produced in this study were grown with the crucible sta-

Jan 1, 1969

By P. H. Dudley

A quarter of a century of service of steel rails on our oldest railroads, many of which have changed their standard sections three or four times, has furnished, and is furnishing, excellent opportunities to study their wear and behavior in the track. Such experience is valuable for the design of new sections, now required to meet the constantly increasing severity of railroad service. Before presenting the new sections for consideration, I will briefly call attention to some features of past experience. For convenience of study, rails may be separated according to their weight and height into four groups, viz.: 1. Hails weighing per yard from 52 to 60 pounds, and 34 to 4 inches high. 2. " " " " " 60 " 72 " " 46 to 44 " " 3. " " " " " 72 " 90 &apos; 41/8 to 5 4. " " " " " 85 or more " " over 5 " I Experience in this country is confined mainly to sections in groups Nos. 1, 2 and 3. • During the past few years I have had the opportunity to run my car over many thousands of miles of railway laid with the principal sections in use, and to obtain diagrams showing their deflections, permanent set, and, in a great measure, their manner of wear. The First Group.—The first steel rails imported, and those manufactured here, were light sections—included in the first group—and many of them, being rolled in rolls used for rolling iron sections, have pear-shaped heads, 2 3/8 to 2 1/2 inches wide, the base being heavy and from 1/4 to 1/2 inch narrower than the height. These rails were laid upon ties of solid timber, at least 8 inches face, spaced 2 feet from center to center. The moments of inertia of these rails were low, only ranging from 8 for the lightest sections to 12 for the heaviest. The deflections were, of course, great; but the quality of the metal was excellent. It was physically hard and

Jan 1, 1890

By Robert F. Mehl

EXTENSION of physical and chemical methods of research in the study of metallic behavior continues rapidly, particularly in the correlation of behavior with crystal structure, and in the analysis of elastic and plastic properties. The growth of the science of metals during 1933 calls for special comment; the need for special reviews and for textbooks and monographs is now acute, as might he supposed from the number of references appended to this article, a list which is much abbreviated.

Jan 1, 1934

By Henry Doherty

FOR many years more money was spent in the search for and the production of gold than the gold that was produced was worth. The same thing is now true of petroleum. More money is spent for the search and. production of petroleum than the market value of the petroleum produced. The first thought concerning this statement will be that men would not embark in a business in which more money was expended than the value of the product produced. Few people realize that more money is spent in the oil business than the market value of the oil produced. This would not stop the spending if they knew it. Everybody knows that more money goes into a lottery than comes out of it, yet the instinct for gambling is so widespread and so easily excited that lotteries are forbidden by law. The hope of winning the grand prize is what lures men on. The search for and production of oil has become a more frenzied game than the search for gold ever was. THE OIL BUSINESS PAYS NOW BUT THE PUBLIC WILL PAY FOR ALL ETERNITY The public could sit back and enjoy all of this, knowing they were being supplied with petroleum products at less than their real cost, if it were not that our most valuable and least plentiful natural resource is being dissipated at an alarming rate, which is constantly increasing. Here is an industry that for many years has not been governed by natural laws. The so-called laws of individual and mass psychology play a more important role than natural physical and economic laws. Even the law of supply and demand works only in the most remote way in this industry. The oil production business as a whole is now paying the price for this folly; but the public will pay the price for all eternity. The seriousness of this matter, as an outstanding national problem, has been under consideration by many men for a long time, but nothing has been done to conserve our petroleum resources and prolong the supply, although very important steps have recently been taken to make this possible.

Jan 3, 1925

By AIME AIME

T HE 121st meeting of the Institute held in New York City, February 16 to 19, 1920, was a great success despite vicissitudes of weather of unusual severity. On account of tremendous snowstorms, only two members of the Canadian contingent arrived, and several of our members from the west arrived thirty hours late. Two weeks prior to the meeting, the heaviest snowstorm in 34 years wrecked the surface transportation in New York; and it was only by special dispensation that arrangements were effected, with the New York Street Cleaning Department to clear away 39th street in front of this building so that vehicles could reach the curb. The total registration of members and guests was 1138.

Jan 1, 1920

By George A. Miller

THE outstanding characteristic of the American business man is that he likes to run his own business his own way, without any interference from his wife, his friends, his bankers, and least of all from his government. The oil man, like the miner, is an American business man in which this special characteristic is even more pronounced. It may be because he has been an explorer and is more nearly like those pioneering Americans who explored, developed, and built these United States.

Jan 1, 1944

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster&apos;s New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By O. U. Bradley

THE extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, somelosses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. , Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 13 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of. 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause, more or less deterioration in quality, particularly when the fresh production is run direct from the. gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks.

Jan 7, 1918

By RALPH HAYES SWEETSER

IRON ore and bituminous coal are the two basic raw materials for the whole iron and steel industry. The ore furnishes the iron and is absolutely necessary-all iron and steel products come directly or in- directly from the iron ores. The bituminous coal furnishes the carbon needed for the smelting of the ores and for the fuel used in all the processes of iron and steel manufacture. The necessary carbon could be furnished in some other form besides bituminous coal. In fact, it is only since the Civil War that bituminous coal has been the chief source of the carbon for metallurgical fuel. For many years only charcoal made from the forests furnished the carbon for smelting iron ores. About 90 years ago, anthracite coal was first used as blast-furnace fuel and for many years continued to be the chief blast furnace and steel making source for carbon. Even in my own blast-furnace experience, I have used charcoal in Canada and anthracite in Pennsylvania for smelting ores in an iron blast furnace. Bituminous coal, now almost exclusively the source for the carbon used in smelting iron ores, also furnishes most of the heat used in the steel-making processes. It is seldom used in blast furnaces in its natural condition, hut is first coked in beehive, or in by-product coke ovens; such bituminous coal is called "coking coal." Bituminous coal that is suitable for making the producer gas used in the open-hearth steel process is called gas coal. Any bituminous coals suitable for making blast-furnace coke or foundry coke, or that can be satisfactorily used for making producer gas, are classed as metallurgical coals and as such are to be considered in my proposed plan for the evaluation of metallurgical coals. According to Bureau of Mines Bulletin No. 449 these coals comprised 22 per cent of the bituminous coals mined in this country in 1923.

Jan 1, 1926

A. M. CANDY,* Pittsburgh, Pa.-I think more stress should be laid upon the question of welding with the carbon electrode, which we ordinarily call graphite arc welding. Mr. Miller&apos;s photograph indicated that the original parent metal had been decarburized to a marked degree. It would be interesting to know the carbon content of the parent metal, and whether or not Mr. Miller has made any investigations to determine if the metal is always decarburized or whether in some instances we actually have carbon injected into the weld, which has been the understanding that has been quite prevalent. There were one or two other points that Mr. Miller brought out concerning which I desire to ask one or two questions: The illustrations that he presented were obtained with what, I suppose, would be termed a real low-carbon steel welding wire, which gives in the deposited metal grains that are more or less symmetrical, whereas the Roebling electrode, which is a mild steel of higher carbon content, apparently gives a columnar structure. I do not know which-of these I structures is more desirable, but assuming that the structure produced by the really low-carbon steel wire is the more desirable, would it not be true that the very low carbon content would, probably owing to high temperatures that prevail in the arc, result in a greater amount of oxidation and probably result in either carrying into the weld more oxide or producing more oxide on the surface as the operator progresses? The short arc is an advantage in all cases. Whether Mr. Miller&apos;s trouble is oxide or nitride, the short arc helps him out, because the closer the end of the electrode is to the work the less chance there is for either oxygen or nitrogen to get in. And whichever is the cause of the trouble, the short arc keeps it out by lessening the time in which the steel is molten and the amount of air that gets in. It also makes sure that the molten metal will not fall into the crater. Everything is in favor of the short arc.

Jan 4, 1919

By J. D. Wood, J. T. Smith

ALLOYS with a dispersed second phase in a metallic matrix are generally much stronger than the matrix itself. Plastic deformation in dispersion-strengthened alloys is usually confined to the matrix phase when recovery processes are active, while in the absence of recovery both phases may yield.&apos; The alloy system studied in the present research was WC-12 wt pct Co and consisted of noncoherent WC particles dispersed in the cobalt matrix. Some particle-to-particle contact existed but not enough to produce a continuous WC skeleton. The microstruc-ture of the WC particles was characterized by very straight edges, forming a trapezoidal shape in any plane of polish. Previous investigations with WC-Co alloys at room temperature have shown that fracture of the WC particles occurs in transverse rupture testing.&apos; Room-temperature slip was reported for WC particles after indentation for hardness measurements.3 Elevated-temperature deformation of WC particles in a WC-12 pct Co alloy was suggested by recent electron microscope studies of specimens deformed at 900&apos; to 1000°C.4 In highly deformed alloys, the WC edges were serrated in contrast to the usual straight or smooth appearance. WC-12 pct Co and WC-15 pct Co alloys have been previously studied under elevated-temperature com-pressive-creep conditions by the present authors. Electron microscope studies of two-stage replicas from deformed specimens showed no evidence of slip or fracture of the WC particles. These specimens were brought to temperature and allowed to equilibrate prior to the application of the creep load. It was believed that the load-application rate, a crosshead speed of 0.005 in. per min on an Instron universal testing machine, was sufficiently low that recovery within the cobalt matrix was sufficient to limit the deformation to this matrix. A series of experiments was performed to evaluate the influence of loading rate on the deformation of WC-Co alloys. A WC-12 pct Co alloy was selected for these determinations. The average WC particle size was 4.45 p with an average linear separation between particles of 0.59 p. The selected temperature was 800°C and was monitored with a Chromel-Alumel thermocouple attached to the specimen. Testing was conducted in an argon-atmosphere chamber to prevent oxidation of the WC-Co specimens. This chamber was mounted on an Instron universal testing machine equipped to apply the load at a fixed rate. Each specimen was loaded to 110,000 psi compression stress at 0.05 and 0.5 in. per min. The loading rate was monitored prior to insertion of the test chamber and was found to be almost precisely the nominal rate selected. The specimens were raised to temperature and held to equilibrate with the surroundings, and then the load was applied and held for 4 hr to duplicate the exposure time utilized for the creep specimens. The time to reach full load at a crosshead speed of 0.005 in. per min was some 500 sec and was reduced to 50 and 5 sec as the loading rate was increased to 0.05 and 0.5 in, per min, respectively. The model developed by Ansell,&apos; when recovery processes do not occur, considers that fracture or deformation of the dispersed particles is necessary to relieve back stresses on dislocation sources and allow dislocations piled up against particles to sweep out in the matrix to cause plastic deformation; he further states that, even at elevated temperatures, the dispersed-particle deformation is necessary for yielding in the absence of recovery. For the case of straight dislocation segments piled up against a straight barrier, such as the straight-sided WC particles, the shear stress, 7 exerted on a particle is: where h is the spacing between particles (0.59 p), a is the applied stress (110,000 psi), p, is the shear modulus of the matrix (6.7 X lo6 psi at 80O°C), and b is the Burgers vector of the matrix dislocation. From Eq. [I], the shear stress, 7, exerted on the WC particles when no recovery occurs is of the order of 6 X lo6 psi at 800°C. The limiting stress, F, that will

Jan 1, 1969

By F. L. Clerc

THE lead and zinc region of SW. Missouri is interesting, not only by reason of the value of its output, which ranges in the neighborhood of ten million dollars a year, but even more because of the facilities which it offers for the study of certain forms of ore-deposits, of which the loci and genesis are somewhat obscure. Although the mineral species found in the region are few and of common occurrence, crystallization has taken place on a generous scale, and unusual forms abound in many combinations, presenting examples of pseudomorphism, paragenesis, metasomatic replacement and the action of mineral-depositing and mineral-dissolving waters. For the mineralogist, lithologist, and specialist in certain lines of metamorphism, it has peculiar attractions, while the systematic geologist will perhaps find its chief claim to attention in the simplified problem it presents, in the study of ore-deposits. In addition to the phenomena above enumerated, it presents instances of well-developed comb-structure in the ores, fissures and faults, and slickensides-features usually associated with extensive movements in the earth&apos;s crust, and believed by some authorities to prove the deep-seated origin of the ores. In connection with these occurrences, the absence of all igneous rocks from this region is noteworthy and significant. For that reason, the simplified case presented by the Joplin region, from which these rocks have been eliminated as a factor, is specially valuable. Having had unusual opportunities to watch the development of this district, I have been deeply interested in the bearing of the revelations of the Joplin mines upon questions of universal importance to the science of ore-deposits ; and it was to my great regret that the project of a meeting of the American Institute of Mining Engineers at Joplin, proposed in 1892, was

Mar 1, 1907

By K. M. Rolls, F. W. Reuter, J. Wulff

The superconducting behavior and microstructural characteristics of a nominal Nb-40 wt pct Ti-0.239 wt pct O alloy were studied as a function of ther mo -mechanical processing treatment. Critical current density us applied transverse magnetic field was obtained for 0.010-in.-diam wires at 4.2°Kin steady fields 14 to 110 kG. Both optical metallogvaphy and transmission electron microscopy were used to delineate the micros tructures of the same wires. It wan found that a 1-hr 500°C precipitation heat treatment after cold drawing to final size led to the highest critical current density. Heat treatment at 600°C also led to a high critical current density, but the precipitate differs in kind and form from that at 500°C. The resistire critical field was also found to be sensitive to precipitation heat treatment since the effective composition of the superconducting phase changes. This is discussed in terms of the oxygen in interstitial solid solution. Two types of high-field superconducting wire are at present used in the construction of high-field superconducting solenoids. These types are solid-solution alloy wire such as Nb-Zr and Nb-Ti and composites of the brittle inter metallic compound Nb3Sn. The latter generally have a high super cur rent-carry ing capacity which is difficult to vary if properly made. The supercur rent- carry ing capacity of the former can be varied drastically and often predictably by suitable thermomechanical processing treatments. In general, the critical current density Jc of the solid-solution type of alloy is increased by cold work and by additions of interstitial elements along with aging heat treatments. The imperfections which result are be-iieved to be responsible for the observed increase in Jc. In 1962 Kneip and coworkers1 found that the critical faurrent density of Nb-Zr alloys could be increased by proper heat treatment preceded and followed by cold work. Betterton and coworkers2 using a Nb-25 at. pct Zr alloy found that small additions of oxygen or carbon enhanced the effect of this heat treatment. They suggested that the interstitials present aided precipitation in the alloy, leading to a filamentary structure with superior properties. If the precipitation heat treatment was omitted, interstitial additions had a negligible effect on Jc. wong3 showed that higher heat-treatment temperatures lowered Jc. Walker and co-workers,4 who studied microstructure (by transmission electron microscopy) as well as superconductivity, found that the Jc anisotropy introduced by cold rolling was itself affected by heat treatment. They were unable to clarify the relation between microstructure and critical current density, although evidence of precipitation was indicated. More recent investigation of Nb-Zr alloys,5,6 besides showing that structural defects and fiber ing due to cold work and precipitation serve to raise Jc, also elucidate important optically observable microstructural changes which occur upon precipitation. In these reports, coarsening of the microstructural features was found to decrease Jc. Vetrano and Boom,7 who studied Ti-20.7 at. pct Nb, found that Jc was increased to a maximum by a 415°C, 3-hr heat treatment following quenching from 800°C and cold working. Heat treatments can also affect the resistive critical field Hr. Final-size heat treatments of Nb-Zr wire can lower Hr drastically if gross phase decomposition occurs5&apos;* or moderately if the effects of cold work are eliminated without changing significantly the composition of the phase of interest.3,5,6,8 The percentage of oxygen which can be added to Nb-Zr alloys to enhance Jc is limited by the difficulty of subsequent cold drawing. Since Nb-Ti and Ta-Ti alloys in contrast can tolerate appreciably higher percentages of oxygen, it was decided to investigate the superconducting behavior of various alloys in these systems. The present paper describes the results of adding oxygen to a nominal 40 wt pct Nb alloy as a function of thermomechanical treatment. I) EXPERIMENTAL PROCEDURE A small alloy ingot was prepared from high-purity niobium, iodide, crystal-bar titanium, and Nb2O5 powder by arc melting on a water-cooled copper hearth in a gettered argon atmosphere. The ingot was turned and remelted fourteen times to insure homogeneity. After final melting and rapid cooling, it was machined round to 0.415 in. diam, jacketed in stainless steel, and cold-swaged to 0.117 in. diam. The jacket was removed and swaging continued to 0.051 in. diam followed by wire drawing in carbide dies to 0.010 in. diam. Although it was intended that about 1500 ppm O (by weight) be added, inert gas fusion analysis indicated a 2390 ppm 0 content, apparently due to additional oxygen pickup in the arc furnace. Even so, the alloy was sufficiently ductile to be cold-worked to greater than 99.9 pct reduction

Jan 1, 1967