Search Documents

By N. Jaffee, J. E. Dorn

An activation energy of 27,400 5 1000 cal per mole was obtained for the creep of poly crystaLline aluminum over the temperature range of 273° to 350°K, at strains varying from 0.003 to 0.230. Stresses varied fronz 2250 to 6000 psi, strain rates from 0.1145 x 10-5 to 29.5 x 10~s min.-1. A strain temperature-compensated time correlatzon was oblained indicating that the structure was depedent solely upon the strain at a given stress; X-ray diffraction analyses and tensile tests on precrept specimens verified this. PREVIOUS investigations1 have revealed that the apparent activation energies for creep of high-purity polycrystalline aluminum are insensitive to the applied stress, strain, and strain rate. On the other hand, the apparent activation energy is dependent on the temperature1,2 as shown by the data reproduced in Fig. 1. Each plateau of this curve is associated with a unique rate-controlling dislocation mechanism for thermally activated creep. It is now very well-established that over the high-temperature range, where the activation energy is about 35,500 cal per mole, the creep rate is controlled by the dislocation climb mechanism. 3 Over the intermediate range of temperatures, from about 260° to 370°K, another unique activation energy, namely 28,000 cal per mole, is obtained. Current evidence strongly supports the contention that cross slip is the rate controlling mechanism for creep in this case: 1) Crystal recovery can occur by a number of mechanisms prominent among which are climb and cross slip. Astrom,4 using the Borelius micro-calorimeter, reported rapid crystal recovery of cold-worked polycrystalline A1 at 340° to 370°K giving an activation energy of 28,000 cal per mole and additional recovery at 455° to 478°K giving an activation energy of 3 6,000 cal per mole. Whereas the latter recovery process was clearly associated with the dislocation climb mechanism, the former, 28,000 cal per mole process could have arisen as a result of the cross-slip mechanism. 2) Single crystals of high-purity A1 favorably oriented for octahedral glide exhibit an activation energy for creep of about 3400 cal per mole over the range from 0° to 400°K and that of about 28,O:O cal per mole over the range from 600° to 775°K . Whereas the lower activation energy process is accompanied by the development of sharp slip-band traces, the 28,000 cal per mole process was uniquely characterized by extensive cross slip. 3) Theoretical calculations by Seeger and schoeck6 suggest an apparent activation energy for cross slip in A1 of about 24,000 cal per mole and another theoretical estimate by Friedel 7 gives the observed 28,000 cal per mole as the theoretical activation energy. It is therefore consistent with this evidence to, at least tentatively, ascribe the 28,000 cal per mole creep process in A1 to the operation of cross slip as the rate controlling mechanism. Although creep has been rather well-explored in the dislocation climb range, very little, excepting perhaps the activation energy, is known about creep in the cross slip range. This investigation was undertaken, therefore, to reconfirm the activation energy for creep in polycrystalline A1 in the intermediate temperature range and to study the strain-time relationship for creep at a constant stress in the cross slip region. EXPERIMENTAL PROCEDURE AND TECHNIQUE The three types of high-purity A1 alloy specimens described in Table I were used in this investigation. Specimens were milled from 0.100 in. thick cold-rolled sheets with their tensile axes in the rolling direction following which they were given a recrys-tallization and grain growth heat treatment at temperatures well above those which were subsequently employed in the creep tests.

Jan 1, 1962

By A. D. Hughes

A relatively small area in Malaya, about 200 miles long by 40 miles wide, is the most important source of tin in the world. Some tin is recovered in other parts of the peninsula. Of the tin mined, 98 pct is recovered from alluvial deposits. From 1935 to 1941 the average annual world production of tin was 190,000 tons. The average annual production from Malaya during the same period was 62,000 tons or about one third of the total. Other producing countries, in order of importance, were the Netherlands East Indies 34,000 tons, Bolivia 30,000, Belgian Congo, Nigeria, Siam, Burma, China, and a few others with smaller amounts. The serious shortage of tin during the war period was due to the fact that the Japanese were occupying Malaya, Netherlands East Indies, Siam, Burma, and China which, together, formerly were producing 65 pct of the world supply.

Jan 1, 1949

By AIME AIME

THE following paragraphs, constituting the concluding portion of the Annual Report of the Council for 1903, have been withheld from publication until now, in order to make them as accurate and complete as possible. They will be published in Volume XXXV. of the Transactions in their proper place at the end of the said Annual Report. Franklin Ballou was born in Pittsburg, Pa., May 29, 1845. He was the son of an old resident, Arthur Ballou, a manufacturer and wholesale dealer in vinegar. In early youth Franklin attended the Western University of Pittsburg, but left school at the age of 16 to become book-keeper for his father, upon whose retirement from business, in 1868, he associated himself with Walter C. Childs, of Pittsburg, in the manufac¬ture of furnace-grates and asbestos-cement for blast-furnaces. This firm was known as W. C. Childs & Co., and did a success¬ful business for several years. In 1869 Mr. Ballou married Miss May S. Wilson, daughter of Judge Wilson, of Lewistown, Pa. In 1876 he spent several months traveling in the West and studying the mining industry, which greatly interested him. In consequence of this journey, he wound up his business in Pittsburg and removed in 1877 to Georgetown, Colo., where for several years he conducted a sampling-works, and built up an extensive business as an agent for the sale of ores, besides engaging to some extent in mining enterprises. , It is said that he controlled at one time about one-eighth of the output of the Leadville mines. In the early 80's, he became Vice-President and General Manager of the Bimetallic Smelter at Leadville, of which Mr. David H. Moflat was the principal owner. This was practically the first successful demonstration of pyritic smelting in Colorado. Upon the sale of the works in 1897 to the American Smelting and Refining Co., Mr. Ballou retired

Jan 1, 1905

By Charles R. Fettke

In connection with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,' a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 11/2 miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated as Nos. 1, 2, 3, and 4, respectively, on the map shown in Fig. 1. Others are probably present, but escaped notice on account of the thick mantle

Jan 1, 1924

By G. S. Cole

The temperature has been measured ahead of stationary solid-liquid interfaces under conditions approximating luzidirectional heat flow and therefore unidirectional solidification. Natural convection flow patterns may be deduced from the temperature distributions , temperature fluctuations, and shape of the interface. Fluid flow increases with the height and the rate of heat transfev through the interface and this is further manifested by a deviation of the interface from aflat vertical plane. The influence of fluid flow on solute inhomogeneity during alloy crystal growth can be inferred from the observed temperature distributions. A buoyancy force exists in the liquid ahead of a vertical solid-liquid interface, caused by a difference in density between cold fluid near the interface and warmer fluid in the bulk liquid. When the viscous and inertia forces in the melt exceed this buoyancy force, a flow of fluid takes place, termed natural or free thermal convection. Natural convection in purely liquid systems has been extensively studied for many years. 1"u On the other hand, fluid flow during horizontal crystal growth has oniy recently been the subject of experimental investigation."-25 The requirements for horizontal crystal growth differ from other heat flow systems. The small aspect ratio (ratio of height of cold wall to length of fluid) has never been considered. The uniform furnace gradient which supplies heat radially (and not necessarily symmetrically) differs from previous boundary conditions of uniform heat flux at the cold and hot ends. And most important of all an isothermal s/l interface is present which can adjust its shape and position to conform to heat and fluid flow. All of these boundary conditions involve complexities which cannot be readily solved analytically. Preliminary observation has demonstrated the penera1 shape of the natural convective flow pattern in transparent media.20'24'25 The flow is circulatory, directed toward the interface at the surface of the liquid, down and away from the interface at the bottom, and then up at the hot end of the melt. During crystal growth such a flow may interact with the solute boundary layer at the s/l interface to affect solute incorporation.M'1B|28'i!T Evidence has also been presented recently to show that thermal convective flow will affect the structure of ca~tin~s.~~-~~ The rate of heat transfer (conduction plus convection) in a given fluid system is a function of the temperature difference between the hot end of the liquid and the s/l interface and the height of the interface. At the lowest values of these variables* all heat is *It has been shown' that adverse temperature gradients as low as O.OOS°C oer cm are sufficient to cause convection. transferred by conduction. When the temperature difference or interface height are increased, laminar fluid flow commences and heat transport takes place by laminar convection as well as by conduction; turbulent heat transfer takes place at higher values of these variables. In the transition region between laminar and turbulent flow, boundary layer separation takes place; fluctuations in temperature are also noted and increase in amplitude and frequency as turbulence becomes dominant. In this paper, fluid flow patterns in the melt ahead of a stationary interface are deduced from observations of temperature distribution and fluctuations, heat flow rate, and interface shape. The fluid flow ahead of advancing interfaces and the effect of such flow on solute incorporation may be inferred from these measurements on stationary interfaces. Observations during enforced fluid motion will also be considered. EXPERIMENTAL PROCEDURE The metal was contained in a lava boat 10 cm in length, 1+ cm in width, and 2 cm in height, as shown in Fig. 1. A water-cooled, molybdenum block heat-sink is at one end of the boat; surrounding this assembly is a slotted stainless-steel tube noninductively wound with a nichrome heating element. Temperature was measured by 38-gage Chrome1 vs Alumel thermocouples sheathed in 0.05-cm-diam graphite-coated stainless-steel tubing, which were moved longitudinally and vertically through the melt by means of a two-dimensional motorized micrometer stage. In some experiments the thermocouple junction was exposed, but in the majority of experiments the junction was welded to the sheath tip; no significant difference

Jan 1, 1968

By Philip B. Bucky

WITH the exhaustion of the sections of iron ore bodies amenable to opencut mining the iron ore miners raise the question: "How can we mine the extensions of these ore bodies in depth with the same costs as obtained in opencut work?" This question brings to the fore the relationship between mineral exploration and research on mining procedures. The iron miners must either find new de? posits amenable to their known methods of mining or develop new mining methods for deep deposits. It is understood that the oil companies will spend $30,000,000 next year in the search for new oil fields. How much the metal mining companies will spend in the search for new ore bodies is unknown, but without doubt the amount will run into several millions of dollars. If the mining companies that concern themselves with metals, nonmetallics, and fuels will set aside a substantial sum for fundamental and applied research in mining methods, they can not only lower their costs but increase their reserves thereby. Any increases in mining efficiency automatically result in increased ore reserves at no cost.

Jan 1, 1947

Fred. T. Greene, Rossland, B. C. (communication to the Secretary): At the beginning of his gaper, Mr. Herzig refers to an article of mine in the Engineering and Mining Journal of January 27, 1900. I would like to add that the method de-

Jan 1, 1901

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By R. M. Brick

EDUCATIONAL benefits for veterans of World War II have largely removed one of the two former barriers to a college education for everyone, namely financial means and intellectual capacity. This latter limita¬tion has not kept privately endowed institutions from increasing 50 to 100 percent in size of student body, even after applying moderately rigid entrance standards. Growth of some land-grant universities, which cannot well exercise such restrictive judgements, has been even greater. After a weary board of admissions, subject to student, alumni, faculty, and even political pressures, has admitted double the former number of freshmen, the university&apos;s worries really begin: to find laboratory, classroom, and instructional facilities. If this were a one- or two-year problem, the answer would be simple: double up, hold night classes, particularly of laboratories, rent space, and have instructors work 24 class or contact hours a week instead of twelve (it takes usually two to three hours of outside work by the instructor for one hour in class). However, most engineering school faculty men are worn out now from four to five years of "accelerated" (frequently downward!) programs and they couldn&apos;t continue teaching in a way satisfactory to their own consciences on

Jan 1, 1947

By H. T. Kennedy, S. G. Dardaganian, J. L. Clanton

This paper presents equilibrium ratios measured on oil and gas samples taken from the Kelly-Snyder field at the reservoir temperature of 128°F. From these data smoothed curves were constructed for the reservoir fluid up to the bubble-point, 1,874 psia. A material balance calculation, based on the use of equilibrium ratios instead of the usual solubility and shrinkage meayr~rements is made on the field and compared to the con\.entional method. DETERMINATION OF EQUILIBRIUM RATIOS The equilibrium ratios, or K values were obtained by recombining separator samples of oil and gas taken when the reservoir was above its bubble point, and thus represented the reservoir fluid before any change had occurred due to the evolution of gas. The well sampled had a gas-oil ratio of 617 cu ft of high pressure sepalator gas per barrel of separator oil. and a bottom-hole temperature of 128°F. Samples were brought to equilibrium by agitating for 24 hours in a thermostat, maintained at the proper temperature within 0.2ºF, mercury being added when necessary to maintain the pressure constant. Samples of oil and gas were then taken by constant pressure displacement, and analyzed by low temperature frac-tionation. Equilibrium ratios were determined at 128°F and 500, 800, 1,000 and 1,400 psig. At the latter pressure, there were indications that the gas samples were contaminated with small quantities of oil, and only data taken at the first three pressures were included in Fig. I. This figure has been extended to higher and lower pressures by the use of the Fluor charts for 3,000 psi convergence pressure, on which the experimental points fit well. MATERIAL BALANCE EQUATIONS The possible errors involved in conventional material balance equations have been analyzed by Muskat1. Where the errors occur in field measurements, or in obtaining effective averages from variables such as gas-oil ratio and pressure, they will evidently be involved in any attempt to estimate the content of the reservoir. On the other hand, substantial errors may be introduced in conventional material balance calculations by: (1) the neglect of the amount of oil dissolved in gas at high pressures and temperatures in the reservoir, but which condenses under separator conditions; (2) the assumption that the separation of oil and gas in the reservoir may be duplicated by a differential liberation in the

By F. Lowell Lawrance

JOHN SMITH, citizen of the U.S.A., has become so accustomed to reading that Congress has appropriated billions of dollars to pay war costs. that he no longer is impressed by relatively small figures, such as several hundred thousand or a few million, in connection with Government departments.

Jan 1, 1944

By D. Mills, G. B. Craig

The defortnaliotz of zirconicltt single crystals conlaining osygen in the range 740 to 6800 atom parts per nilllion was esanined oc7er the range 77" to 950°K. An anctlsis of the dqfarmaliotz parameters leads to the cotcllsiotr that the rale -cotzfrolling thermally activated dqivr,irrtion process oe-r /he range 77" to 560°K is oc.crco,ling osvgen alotns. A thermally actitaled defor,ilntion process is not found between 600" and 800", but does occur aboz%e 800°K. THE present investigation was undertaken to measure the effects of controlled amounts of oxygen on the deformation parameters of a zirconium single crystals over the temperature range 77" to 950°K and to determine the rate-controlling mechanisms. Although there is no doubt that the mechanical properties of the group IV metals, titanium, zirconium, and hafnium, are strongly influenced by the interstitial impurities oxygen, nitrogen, carbon, and hydrogen, there are many conflicting theories as to the role played by the interstitials during the deformation proess.&apos;- There is general agreement that the mechanisms which control plastic flow in a metal impose characteristic values on such parameters as the flow stress and its temperature dependence, the activation volume, and the activation energies. These parameters will be used to analyze the deformation mechanisms. eltham,&apos; Sargent,16 and ibbs&apos; have shown that the stress relaxation technique allows the activation volume characteristic of the deformation process to be found during the course of a simple tension test. In many cases it is found that the relaxation of stress is logarithmic with time and obeys a relationship of the following form: T-T = AT =S logl0(qt + C) [I] where t, is the shear stress at the start of the relaxation test, t is the shear stress at time t, and S. q, and C are experimental constants, and S is the strain rate sensitivity of the stress t as shown in the appendix. The slope found from a semilogarithmic plot of At vs time is approximately equal to S. The activation volume u, association with the deformation process, is found from the following relationship: The theoretical treatment of thermally activated plastic flow due to schoeck18 shows that the activation volume when combined with the temperature dependence of the flow stress gives the activation energy for the process according to equations: seegerZ3 considers that the flow stress at lower temperatures ld is composed of two parts such that Tapplied = tinternal + Teffective , where Teffective 3 ff , is the stress necessary to overcome the local obstacles to deformation and Tinternal, ri, is the stress necessary to overcome the long-range elastic stress field of dislocations on other planes. ri is considered to be largely elastic in origin and can be estimated from the stress value at the temperature independent portion of the flow stress-temperature curve. EXPERIMENTAL The crystal bar zirconium used in this investigation was supplied by Wah Chang Corp. whose certified analysis gave the following impurity contents in parts per million by weight: oxygen, 150; nitrogen, 10; iron, 180. All others were less than 100 ppm. The oxygen and iron contents were confirmed by neutron activation and chemical analyses, respectively. Single crystals were grown in an electron beam furnace according to the method of Wilson and Pickle-simer&apos;&apos; and ills.&apos;&apos; The orientation of the crystals was such that the specimen axes were located in the lower third of the standard section of the basal plane stereographic projection for zirconium. This orienta-

Jan 1, 1969

IN the extra-mural service being built up by the Engineer-ing Societies Library as its finances permit, an occasional large total charge is incurred for exceptionally protracted services. A western steel company, for example; was charged the unusual fee of $500. They wanted complete informa-tion on transverse tests of steel, and asked the library to compile copies of all accessible records. Weeks -of search-ing and photoprinting produced three volumes of data. Two years afterward the company&apos;s chief engineer told the director of the library that the cost seemed high when the bill was paid but that the volumes had been in constant use. The information had been worth thousands of dollars. A client who wishes to pay no more than a moderate fee for services can state to what limit he is willing to go. Thus he may specify that he would like searches made on a particular subject but that he does not wish to exceed $5 or $30- for the information. The library is as willing to perform a small service as a large one.

Jan 3, 1928

By O. J. Neslage, R. W. Jenkins

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today&apos;s wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By R. W. Jenkins, O. J. Neslage

MINE operators today are paying increased attention to the mechanization of drilling operations as an important factor in increasing efficiency and decreasing costs. Recent progress in the design of drill jibs for mounting on drill carriages, or jumbos, has done much to advance the mechanization of mining methods. This progress has introduced new opportunities in the application of "jib jumbos" that are worth serious consideration. An attempt will be made here to classify the various types of jumbos and drill mountings available for level development and flat stope work, t6 indicate applications, and to measure their effectiveness in relation to their cost. The data here are based on a wide variety of field usage, and are offered only to point up, in a general way, the relative efficiency in proportion to cost. It should be remembered that any contemplated jumbo installation must be studied to determine what type of installation is most suitable, considering ground conditions, loading, timbering and haulage equipment, service available, and attitude of manpower. Early Drill Carriages: The advantages of some sort of a drill carriage were recognized at the time rock drills were introduced. In drift or heading operations where a fairly standard drill round and cross section were anticipated, as well as in flat bedded deposits where standard slabbing rounds were used, track and crawler-mounted drills found an early application. These first drill jumbos were little more than drill carriers, designed locally and manufactured with materials at hand. Of comparatively simple construction, function, and low capital cost, they usually consisted of a hinged column which supported one or more drills on arms or universal bars. When the column was pivoted vertically, the drills were moved into position. Screw jack extensions reached from the column to the roof and floor to hold the drill rigid. In some cases, particularly in tunnel jumbos, enough weight was carried that rail clamps or roof jacks were sufficient. Many of these column and arm-type jumbos, usually equipped with air and water manifolds, steel racks, and staging for drillers, are still in use today. Some have employed air or hydraulic extensions for securing the columns. They offer the equip-saving advantage of having all the necessary out, ment together, and they un be moved i and t. set up and torn down as a unit. Boom-type Jumbos: When the advantages of to column-type jumbo were seen, operators could to realize the further gains possible. More time could be saved with mechanical assistance to position api drill vertically. A rack on the column and a pinion on the arm for raising and lowering the drill in the manner of a quarry bar were tried with some success. The most outstanding solution to the vertical handling problem was reached with the boom-type of jumbo. Here two or more machines were mounted on a cross arm at the end of a boom that was pivoted at the rear of the track. This was raised and lowered by various mechanical aids. Occasionally air or hydraulic power was used. Nearly all of today&apos;s wagon drills use this boom-type principle. Boom jumbos represent a savings in time and physical effort expended in raising and lowering the drills. The boom must be balanced by the roof of the truck which is secured by rail clamps or type jacks. The most successful application of areawhere this of jumbo has been in the Tri-State area where multiple long-feed machines are used on caterpillar-mounted, boom-type jumbos for slabbing

Jan 1, 1951

By J. H. Henderson, T. E. Morrisson

An irvestigation has been made of the production of oil through horizontal fractures of high capacity and large radius placed at the base of producing formations. The specific aitns of the study were to (I) determine by model studies the reservoir performance when gravity drainage is the only producing mechanism, and (2) develop a method of predicting such perfortnance from commonly measured reservoir proper-ties. Although the theoretical approach tailed to develop a rigorous analytic sorution to the transient problem, it (lid lead to a practical method of predicting performance. Predictions (Ire in good agreement with rates and recoveries observed in scaled-model experinzents. Capillary effects and the influence of relative permzenbil-ity are taken into account. The experimental program was mainly concerned with the influenre of fracture radius, fracture capacily and capillary hold-up on the total recovery and the rate of recovery. Much of the experimental work was done on a triangular model which represented one-eighth of a square well pattern, so constritcted that horizontal fractures of varying radii and flow capacity could be studied. An electrolytic model was used to relate the initial production rates to fracture radius, formation thickness and the drainage radius of the well pattern. The conclusions reached as a resrtlt of the work are as follows. I. The production of oil under gravity force alone into a well-propped horizontal fracture, whose radius is of the order of hundreds of feet, is a recovery method which combines high recoveries with very acceptable production rates. 2. The mechanism is effective in "dead oil" reservoirs as well as in reservoirs which possess the energy of solution gas. 3. A method of predicting performance has been developed which gives good agreement with experimental behavior in cases of practicnl interest. Even for very thick beds and large fracture radii, where actual conditions do not conform to the assumptions made, the method gives order of magnitude predictions which would not otherwise be possible. INTRODUCTION Gravity drainage of oil from a formation which has continuous ver- tical permeability over a reasonable depth interval is a surprisingly effective method of recovery. However, for a conventional well the production rates which result from gravity drainage are so low that the economics are seldom attractive. The same formation may produce rapidly and profitably by gravity alone through a high capacity, extensive (i.e., > 100-ft radius) horizontal fracture placed near the bottom of the pay section. Fig. 1 shows a schematic diagram of the plan. Energy in the reservoir gas is not a necessary condition for this recovery process. With a sufficiently large fracture, attractive production rates will result from gravity flow alone, and the producing GOR need only be the solution GOR. It is, of course, necessary to keep the fluid level in

By Thomas T., Read

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for ,this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1893, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 30 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1893 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941

By R. M. Brick, M. A. Williamson

Certain features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difierence in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and go", as compared with drawn brasses, at 45o, for all compositions between oo-10 and 70-30.4 Data on indi- vidual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 Experimental Methods The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 bras. Sections 1/4 in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled—i.e., turned through 90° for each pass—and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained.

Jan 1, 1941

By R. M. Brick, M. A. Williamson

Certain features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difierence in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and go", as compared with drawn brasses, at 45o, for all compositions between oo-10 and 70-30.4 Data on indi- vidual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 Experimental Methods The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 bras. Sections 1/4 in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled—i.e., turned through 90° for each pass—and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained.

Jan 1, 1941

By P. Shahinian, R. L. Stegman, M. R. Achter

Creep strength has been determined as a function of oxygen pressure for nickel at 510" and 600°C. Creep-rupture life drops from its highest value at the ultimate vacuum of 10-7 torr to a high pressure plateau of nearly constant life which, at 600°C, commences at torr. This behavior is described in terms of a model that relates surface gas adsorption and the generation of fresh crack surfaces. In a calculation based a this model the predicted pressure beyond which the creep strength should not decrease further has been found to agree well with the observed value. The introduction of oxygen during creep in vacuum was found to cause a prompt rise of the creep rate. The magnitude of the environmental effect was much less than generally observed in fatigue and this is attributed to the diffarent crack morphologies in creep and fatigue. GASEOUS environments are known to affect creep resistance adversely1-5 but the effects have received less attention than the much larger ones in fatigue. At low temperatures it has been shown for nickel that the creep rates are faster and the rupture lives are shorter in air than in vacuum and that these environmental effects can be correlated with faster crack growth rates in the reactive environment.&apos; In support of a mechanism of gas adsorption at the crack tip to explain the above effects, a calculation based on kinetic gas theory showed that surface coverage by gas was not as rapid as the exposure of fresh metal at the crack tip in the ultimate vacuum but was in air.7 In fatigue a number of investigations have demonstrated that the reduction of life with gas pressure usually follows a step curve with most of the reduction occurring in a transition range at intermediate pressures and little or no change at high and low pressure.8 There have been no studies, however, in which creep strength has been determined as a function of reactive gas pressure to see whether similar effects would be found. This investigation was undertaken to study the kinetics of the environmental effect in the creep of nickel. EXPERIMENTAL PROCEDURES The environmental creep apparatus was constructed to minimize many of the experimental conditions which can cause scatter in data. Dead weight loading is employed and weights are contained within the environmental chamber to eliminate bellows and the necessity for compensation for gas pressure changes. Elongation over the specimen gage length is recorded from a Riehle Model DV Controlled Environment Extensometer which provides readout to 2.5 x 10- in. Temperature is monitored and controlled from a thermocouple at- tached to the specimen gage length to +0.5oC or better. The freon trapped oil diffusion pump vacuum system included an auxiliary liquid nitrogen trap and, with a wide range variable conductance leak valve, pressures from the ultimate vacuum of 10"7 to l03 torr of any desired gas are obtainable. Pressure is measured by means of a hot filament ionization gage below 10"3 torr and a NRC Model 530 Alphatron Vacuum Gauge above 10-3 torr. The oxygen, which was leaked into the environmental chamber, was an Aviator&apos;s Grade of 99.5 pct purity with a dew point of -80°F. Analysis of the nominal 99.8 pct Ni showed the following percentages of major impurities: 0.02 C, 4.01 Mn, 0.005 Si, 0.01 Cu, 0.02 Fe, and 0.034 Mg. Cylindrical specimens were machined with a 0.180

Jan 1, 1970