Search Documents

By Fred C. Bond

MANY grindability tests have been made in the Allis-Chalmers laboratory since the tabulated results were last published.1 The lists of standard ball-mill and standard rod-mill grindability tests are brought up to date in this paper, and considerable new material is added. This includes a tabulation of open-circuit grinding tests, with impact and compression-crushing tests. The standard ball-mill grindability tests (Table I) were made in a standard laboratory ball mill, 12 by 12 in. inside, running at 70 rpm, with a charge of 285 iron balls ranging from 1 1/2 to 3/4 in. in diameter and weighing 20,125 grams. Seven hundred cubic centimeters of minus 6-mesh stage-crushed dry feed was used, and the circulating load was maintained constant at 250 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 28 to 200, and the grindability is the number of net grams of screen undersize produced per revolution. The table includes 479 tests. It has been calculated that the ball mill does 52.3 joules of useful work on the ore per revolution2 with 93 joules input to the mill. The standard rod-mill grindability tests (Table 2) were made in a laboratory tilting rod mill, 12 in. in diameter by 24 in. long inside, with a wave-type lining, running at 46 rpm. The grinding charge consisted of six 1 1/4-in. diameter and two 1 3/4-in. diameter steel rods, all 21 in. long and weighing 33,380 grams. The mill was rotated level for eight revolutions, then tilted up 5° for one revolution, down 5° for one revolution, and returned to level for eight revolutions. It was discharged by tilting downward at 45° for 30 revolutions. Feed consisted of 1250 cc of minus 1/2-in. stone and the circulating load was maintained constant at 100 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 3 to 65, and the rod-mill grindability is the number of net grams of screen undersize produced per revolution. The table includes 105 tests. The impact and compression-crushing tests (Table 3) are given in a table that is an extension of a previous publication3 in which the method of testing was described in detail. Two equal hammers weighing about 30 lb each were arranged to strike simultaneous blows on opposite sides of the test specimen. Broken pieces of rock passing a 3-in. square and retained on a 2-in. square were set up with the smallest dimension between the hammers, and this distance was measured. The height of the hammers was increased slightly before each blow until the specimen broke, and the foot-pounds per inch of thickness was calculated. Ten pieces

Jan 1, 1947

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.' This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond's grindability tests.' Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

By Bunting S. Crocker

EBBLE grinding at Lake Shore is not a temporary BlE wartime substitute. The tube milling plant, with a 1000 ton per day capacity, grinds a hard siliceous ore to 90 pct — 325 mesh. The plant, prior to using pebbles, was consuming 4.3 lb of 11/4-in. grinding balls per ton of ore, which amounted to 785 tons of balls per year. At September 1951 prices, $132.60 per ton, this steel cost amounted to $104,400 per year, or $0.285 per ton milled. By the Lake Shore method of substituting screened rock for this steel, all of this cost is saved. This is one of the major economies in Lake Shore mill practice. Regardless of the ultimate price of grinding balls, a change back to steel balls is not considered. The present pebble plant is more flexible than a steel ball plant and equally efficient. For example, if it is desired to change the size of grinding media, the pebble charge in any mill can be changed completely in 4 to 5 days, as against 76 days to change completely a 1-in. steel ball charge. To change pebble size it is necessary only to change two sets of screens and clean out the rock feed storage bin. This will take 8 to 10 days as against 3 to 4 months to clean out the customary supply of grinding balls kept on hand. Also it has not always been possible to purchase all desired sizes of balls at any price. In an analysis of savings effected by the use of the pebble mills, the flexibility of the Lake Shore grinding plant should be discussed, as it has a direct bearing on these savings. The plant has always used several units to handle tonnage rather than sending all the tonnage through a single unit. This principle may result in using small diameter mills, but no objection to that is seen. At no time has any advantage been found in cost per ton ground in large diameter mills. Both the capacity and the power of any mill varies as the diameter raised to the 2.6th power. Consequently large or small mills are equally efficient, and a plant, should be designed to use as many units or combination of units as is consistent with reasonable operating practice. Mills under 5 ft diam are harder to reline, etc. To define the case at Lake Shore, 2600 tons per day formerly were milled in seven 7x6-ft ball mills and twelve 5x16-ft (and two 6x16-ft) tube mills.* This gave an excellent test plant and an extremely efficient one. In this plant the ratio of ball mills to tube mills was 1:2. When the much cheaper pebble mills were substituted for the tube mills, this ratio was changed to one ball mill to four pebble mills to take the greatest possible advantage of the cheaper operating mill, i.e., the pebble mill. This flexibility without loss in efficiency has been an important item in the cost savings. It is interesting to note that the use of pebbles for fine grinding was proved first in the laboratory in a 12-in. ball mill. In fact, since 1934 all testing on — 8 mesh material has been done in this 12-in. mill. Scope of the Tests A paper on fine grinding at Lake Shore Mines was published in July 1940.' This paper covered 7 years of intensive research on fine grinding as well as sizing methods and equipment, plant scale grinding tests on 5x16-ft tube mills with and without grate discharges both with 1-in. and -in. balls, the use of laboratory mills to evaluate plant changes, and several reports on classifiers and classification. In the following July the addendum report2 was added in which the idea of series-circuit grinding was introduced, and the results of running five stages of tube mills and bowl classifiers were shown. Since 1940, the ball milling end of the plant has been altered extensively as a result of tests on the use of 3-in. rods in 7x6-ft mills and the use of the Tyler repulping screen with from 7 to 14 mesh screens. These tests are lengthy and may be covered in a separate report later. The scope of this report is confined to ore ground by rod milling and ball milling until it passed through an 8 mesh Tyler Ty-rod screen. The —8 mesh screen undersize then was pumped to a primary bowl classifier in open circuit and the sands from the bowl sent to the primary pebble mills, see Fig. 1. In the pebble mill circuit the ore is ground to 90 pct —325 mesh (24 pct + 28 microns). In studying the flowsheet, attention should be paid to the efficiency of the classification equipment used. The Tyler repulping screen is an efficient machine on the 8 to 10 mesh separation, and the bowl classifier is equally efficient at the 325 mesh separation. Efficient classification is a necessity for series-circuit stage grinding. The ore is hard siliceous porphyry, 60 pct SiO,, 80 pct insoluble. Its grindability at different meshes has been shown near the top of the list in F. C. Bond's grindability tests.' Lake Shore is not shown, but an adjacent mine with identical ore, Wright-Hargreaves, is. Reasons for the Changeover Since 1936 grinding balls have been rising steadily in price with no sign of stopping. For a mill that used 4.5 to 5.2 lb of grinding balls for every ton of ore ground this rise represented an alarming increase in grinding costs. In many cases the quality of the grinding balls fell off as the scrap steel became more difficult to obtain. The ratio of tube mills to ball mills increased with the use of the Tyler repulping screen in the ball mill circuit. Originally only 3.0 lb of balls per ton were used in the tube mills, and this

Jan 1, 1953

By C. C. Clark, J. S. Iwanski

The purpose of this investigation was to study mi-crostructural changes that take place in a commercial nickel-chromium-iron alloy, such as Incoloy "901," over long periods of time at temperatures up to 13 50°F and to correlate such changes with creep-rupture properties. of the alloy. In the course of the investigation, some microstructural changes were observed which correspond to microstructural alterations found in previous studies of Inconel "X." Microstructural phases have been identified in both alloys with the aid of electron and X-ray diffraction and an electron probe microanalyzer. The materials used in this investigation were from commercial heats of the following chemical composition: Pct Cr Pct Ni Pct Mo Pct Fe Pct Cb Incoloy "901" 12.51 43.67 5.72 Bal. -Inconel "X" 14.61 73.44 - 6.61 1.02 Pct A1 Pct Ti Pct Mn Pct Si Pct C Incoloy "901" 0.10 2.46 0.46 0.24 0.05 Inconel "X" 0.70 2.43 0.51 0.36 0.04 Long-term creep-rupture tests were conducted on Incoloy "901" at temperatures of 1000°, 1200°1 and 1350°F. A summary of these results is shown in Table I along with the results of a long-term creep-rupture test conducted on Inconel "X" at 1500°F. The heat treatments given the specimens are also shown in Table I. When the creep-rupture results on Incoloy "901" are compared with shorter-tertn data, there is no evidence of any undue deterioration of the creep-rupture strength with time, nor is the elongation decreased more than would be expected from the influence of time alone. INCOLOY "901" PHASE IDENTIFICATION Microscopic examination of the Incoloy "901" specimens reveals a dark etching grain boundary constituent in the specimen which was under test for about 11,500 hr at 1000°F. This grain boundary constituent was seen to increase in size as the test temperature was increased to 1200" and 1350°F, Figs. 1, 2, and 3. Simultaneously, an acicular structure of definite crystallographic orientation appears within the grains of the 1350°F specimen, Fig. 3. Under examination with the electron microscope, a fine precipitate is observed in the 1200 °F specimen. Fig. 4. It becomes considerably larger in the 2850-hr 1350°F specimen, Fig. 5. In a few areas the precipitated particles have been replaced by, or transformed to, small needles or platelets. After 7380 hr at 1350°F, Figs. 3 and 6, the needles are much larger and have replaced nearly all of the fine precipitate. X-ray diffraction studies detected the presence of hexagonal Laves phase and hexagonal n phase (Ni,Ti) in the 1350°F specimens, Table 11. Only the Laves phase was detected by X-ray diffraction in the 1200°F specimen and none was detected in the 1000°F specimen. In this latter specimen, however, the small quantity of precipitate in the grain boundaries (presumed to be Laves phase) precludes its detection by X-ray diffraction. Composition of the hexagonal Laves phase is not yet known, although its diffraction

Jan 1, 1960

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By H. A. McKinstry, F. F. Lange

A vector analysis of orientating single crystals using the Laue back-reflection X-ray technique is given. Briefly, the analysis involves using a few data taken from a Laue photography and defining the crystal co- ordinate axes in a reference coordinate system. After a few matrix multiplications, the proper goniometer angles can then be determined to orient the crystal coincident with the reference frame. This analysis is easily programed for a digital computer to provide a fast, precise, and efficient method of orienting many crystals which are identical. The general procedure is as follows. The crystal is mounted on a goniometer. Laue photographs are taken until an array of diffraction spots is observed that includes a Laue spot that represents a rotational axis of symmetry. The rotation angles of goniometer are recorded. These angles are defined as positive for a counterclockwise rotation. When the axis of symmetry is located on the Laue photograph, the crystal coordinate axes can be defined in the reference coordinate system* as follows. Two Laue spots are chosen, one of which corresponds to the rotational axis of symmetry and the other to a set of planes whose zone axis is a known crystallographic direction and normal to the rotation axis of symmetry. The Laue spots are used to determine these two crystal directions in the reference coordinate frame. This is done by placing the Laue photograph on a sheet of polar coordinate graph paper and determining the polar coordinates (r, o) of these two diffraction spots in the reference coordinate frame. Their third coordinate is the distance between the crystal and the film (-D). The coordinates Xni of the two crystal directions Nn, (n = 1, 2) in the reference frame are then calculated by the following equations: Xn1 = -D X2n = Ancos on X3n = A, sin on where -tan- 1 rn/D An =Dtan(tan-1rp/D/2) By taking the proper cross products of these two directions (normalized to unit vectors), the crystal coordinate axes 3 (i = 1, 2, 3) can be determined in the reference frame. This is illustrated in Fig. 1. The next step is to determine the relation between

Jan 1, 1969

By John A. THOMPSON, Pazcl D. Torrey, Frank Breayster

DISCOVERY of natural gas in the Dundee field of New York in February, 1930, and the subsequent discovery in Tioga in September of that year, focused the attention of the natural-gas industry on the enormous possibilities of production and distribution in - the most populous area of the United States-New York and New England. Prior to 1926 the natural-gas industry in New York State had settled into a definite and limited policy, with the distributing companies controlling the output from its discovery to the ultimate consumer. Production amounted to between G and 7 thousand mil- lion cubic feet a year, with another 10,000 million feet imported from Pennsylvania for distribution in New York State. This gas was primarily from the Medina sand stone in. the western part of the state.

Jan 1, 1932

By E. J. Efsic, C. M. Wayman

The fcc to bcc y to a transformation in an Fe-24.5 at. pct Pt alloy was studied and found to be martensitic. Large martensite plates are formed in this alloy which are ideal for crystallographic studies; the Ms temperature is about -5°C. Ordering of the parent phase prior to transformation to martensite causes a pronounced lowering of the Ms temperature. For the first time in the case of alloys of iron, measurements of the habit plune, orientation relationship, and magnitude and direction of the shape stvain have been obtained on preselected martensite plates. It is shown that by measuring the initial and displaced (as a result of the shape strain) positions of three or more non-parallel fiducial scratches on one reference surfice the maguitude and direction of the shape strain and the state of distovtion at the parent-mavtensite interface can be determined with a reasonable degree of accuvacy. The agreement between the phenomenolog-cal crystallographic theory of martensitic transformations and the experimental results habit plune, orientation relationship, and nlagnitude and direction of the shape strain) is essentially perfect, and is thought to be the best reported to date for iron alloys. THE comparatively few investigations on binary Fe-Pt alloys have been concerned with magnetic properties, ordered phases, and the equilibrium diagram itself. Various investigations have shown that the equilibrium diagram is of the open y field type; in addition there is a peritectic transformation, a minimum melting point, and three ordered phases: Fe3Pt, FePt, and FePt3. The results of a number of investigators1-6 have shown that the temperature dependence of the y to a (and reverse) transformation in iron-rich alloys is reasonably well-established. The Fe3Pt phase was first noted by Kussman and Rittberg,7 and its existence was later confirmed by Franklin et al,8 Steijn and Donahoe,9 and Berkowitz et al.10 The FePt phase was reported by Isaac and amman' and later confirmed by a host of others.3,6,7,12,13 Kussman and Rittberg7 noted the existence of the superlattice FePt3. Prior to 1956, the 1 to a transformation in iron-rich Fe-Pt alloys was termed "irreversible". In 1957 Klokholm and Donahoe" termed this transformation martensitic, presumably because of its occurrence at temperatures well below those where diffusion normally takes place. This observation served as a point of departure for the present investigation, and in the very early stages of the work to be discussed it was readily verified that the y to a transformation in iron-rich Fe-Pt alloys is indeed martensitic. Quite large martensite plates exhibiting the well-known surface tilt were observed. These plates are ideal in the sense that the boundaries between the parent and product phases were usually very straight. It thus appeared that Fe-Pt martensites would be ideal for crystallographic studies, and this was the purpose of the present investigation. Details of the crystallography of martensitic transformations (particularly for iron alloys) and the phe-nomenological crystallographic theories15-l7 have been discussed many times and thus will require very little elaboration here. The end result of these theories, given in matrix form, is

Jan 1, 1968

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1952

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1938

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1952

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can he readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also. As a matter of fact, we may expect that improved refining processes will make possible the partial recovery of lead and tin which are now lost.

Jan 1, 1928

By Sydney H. Ball

A QUARTER of a century ago, a pessimistic Belgian financier in conversation with the founder of the Belgian Congo, that great ruler, Leopold II, emphasized the danger to the colony should the synthesis of rubber be discovered. The king replied, "I do not worry. The Congo has had its ivory period; it now has its rubber period. Tomorrow it will have that of its mineral wealth; eventually that of agricultural products." That "tomorrow" arrived some twenty years ago. Through her mines the Belgian Congo has survived the present depression, and her mines for the next decade will safeguard her. The Congo, in turn. is the surest foundation industrially and financially of Belgium itself. In few, if any, political units is mining as dominant as in the Belgian Congo. In 1930, 1931 and 1932 mineral products represented respectively 67.9 per cent. 70.5 per cent and 59.3 per cent, of the total exports. In 1933 for each white person in the colony, there was produced about $1,675 worth of gold, diamonds, copper, tin ore and minor mineral products and in 1930 the per capita production, notwithstanding the larger population, was almost $2,000.

Jan 1, 1934

By Thomas H. Leggett

IN speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining-practice, since this has been already well described both in the Transactions1 and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a. whole, marking its general development and the lines of its future progress. In a. paper entitled Deep-Level Shafts on the Witwatersrand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,3 presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (1:). 975): "In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discussed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy was vitally necessary for both 1 Gold-Mining in the Transvaal, South Africa, John Hays Hammond, xxxi., S17 to 855 (1901). R Engineering and Mining Journal, vol. lxxxv., p. 53 (1908). ' Trans., xxx., 947 to 987 (1900).

Jan 5, 1908

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.' IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470' C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" ('. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923

By E. H. Dix

During an investigation of high-strength manganese bronze by til Engineering Division of the Air Service, at McCook Field, Dayton, Ohio, particles of a "blue constituent" were noted in the microstructure of most of the bronzes examined. The constitution of the simple copper-zinc base alloy is still a matter of dispute in spite of the fact that the copper-zinc series is one of the oldest industrially important groups of alloys, and has received thc carly co~l+itlcl-ntio11 of scirntific rcsc:trch. Thc diagram, according to the rnost rcrent \vork.' IS shown in Fig. 1. The disputed questions involve the tcrmi~r:~tiorl of the beta field and the lint at 470' C. The parliest expc~imc>ntcr, Rol)erts--~1~11stcri, detectrd an arrest in some of his cooling curves :it approximately this temperature and ascribed them to the formation of a cutectic; it has since been proved that there arc no eutectics in this series. Shepherd? was unable to detect any thermal arrests at this temperature, his. diagram was essentially as shown in Fig. 1, except that the line at 470" ('. was omitted and the beta phase carried down to normal temperature. 1,:ttcr. carpenter and Edwards, by a very painstaking research, definitely established the authenticity of the line but attributed it to the breakdown of the BETA constituent into a cutectoid of alpha and gamma. microscopic evidence of the formation of the cutectoid is doubtful and it seems more likely to he due to an allo-tropic change in the beta constituent as shown by Fig. 1. At least for practical purpose?, it is more convenient to think of the structure of a 60-40 brass as a mixture of alpha and beta prime crystals rather thin alpha plus an unresoluble eutectoid of "apparent beta" as it has often been called. * Chief, Metals branch, Engineering Division, Air Service. 1 0. F. Hudson: Jnl. Inst. of hlvtals (1913) 12, 2 E. S. Shepherd: Jnl. Phys Chrm. (10141 8, 421. H. C. H. Carpenter and O. A. Edwards: Jnl, Inst. of Metals (1911) 5, 127.

Jan 1, 1923

By R. W. Parsons

wben a displacement front encounters an isolated permeability heterogeneity, it will be perturbed. The details of this perturbation will depend on the beterogeneity size and shape, the Permeability contrast, and the mobility ratio. This paper deals with the displacement front behavior for one, simple, mathematically tractable model: a circular permeability discontinuity and unit mobility ratio. The progress of an initially planar front is shown for four permeability contrasts: k2/k1 = 0, 5/2, 2, m. The front distortion is more pronounced than streamline and isopotential distortion and it approaches a constant shape downstream from the discontinuity. INTRODUCTION The impact of reservoir heterogeneities on oil displacing processes depends upon the variation of the heterogeneous property (frequency distribution), its disposition (spatial distribution), and the inherent stability of the displacement mechanism.l The interplay of these factors plus the impracticability, if not impossibility, of describing a natural rock system in any detail makes exact displacement front movements difficult to determine. It is useful, however, to be able to qualitatively visualize what heterogeneities will do to a displacement front. In this respect certain simple models that can be treated analytically are of value. The following analysis will show the displacement front behavior for one such model. MODEL DESCRIPTION The flow field is two-dimensional and infinite in extent. The fluid flow is single phase, steady state and unidirectional at x, y = 2 m, or before insertion of the discontinuity. A circular permea- bility discontinuity is placed at the origin. Porosity and thickness are the same within and exterior to the heterogeneity. This is exactly the same model that was used by Greenkorn et al. to check analytically Streamlines as determined by Heie-Shaw flow models and finite difference computer techniques.2 FRONT POSITION CALCULATIONS The results of displacement front calculations are presented in Figs. 1 through 4 for four different permeability contrasts: k2/kl = O, %, 2, m. The times corresponding to the front locations are the Same for the 0 and cases! and for the 1/2 and 2 cases. The determination of front positions at various times is based on known analytical expressions for velocity potentials ().2 and stream functions ().2 These expressions are in terms of the x and y

Jan 1, 1969

Prior to any detailed discussion, I'd like to say that Dr. Aplan has made direct hits on two important considerations: 1) The most demanding need in Fine Coal research is to develop improved methods of sulfur reduction. 2) The areas of particle (impurity) liberation and froth flotation hold real near-term promise as techniques for improved sulfur removal. Digressing for a moment, I thin kwe can all remember the time when the biggest problem facing coal research was simply defined - "No money!" In the mid 70's we suddenly found ourselves dealing with a product worth five to seven times the value it carried in the mid60's. All of a sudden, we're talking about a high-profile, high- value commodity. The coal industry still hasn't made the complete psychological adjustment - especially in the operating areas (prep plants included). We have a valuable material at hand which is, in' many cases still being processed as though it were a two or three dollar per ton item. Simply put, I think that while the industry has made some major strides during this transition, a stronger commitment of attitude (and finances) needs to be made toward deeper definition of beneficiation work. Back to specifics - Dr. Aplan has really highlighted three areas where strong research efforts are needed. 1) Liberation processes - not limited to mechanical comminution - must be more fully studied.The industry certainly needs a better handle on value returned (improved ability to beneficiate) for dollars spent on improved liberation. 2) Flotation processes probably hold the most promise for near- term improvement in fine coal beneficiation technology. Dr. Aplan’s.

Jan 1, 1979

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

By J. C. Allen, E. V. Herring

CHILE EXPLORATION CO's. oxide plant at Chuquicamata, the largest of its kind, started in 1915 with initial operations at the rate of 10,000 tons of ore per day. Anaconda Copper Mining Co. acquired the controlling interest in 1923 and in the next few years modernized the plant and mine, extending operations to a nominal capacity of 490 million lb of electrolytic copper yearly by 1942. Plant production averaging 495.7 million lb of copper per year was maintained for the eight-year period extending from 1941 to 1948 inclusive. During the World War II production reached its highest level when in 1944 the output was 531.8 million lb. The maximum production for any one month was 49.6 million lb, achieved in May 1947. E. A. Cappelen Smith, consulting metallurgist for M. Guggenheim's Sons, worked out the first process for the treatment of Chuquicamata copper oxide ore about 1913, and directed a staff of 20 young engineers operating a pilot plant at Perth Amboy, N. J., on three shifts for an entire year. The copper is extracted from the oxide ore by a hydro-metallurgical treatment described in detail by T. A. Campbell in AIME Transactions, Vol. 106, Copper Metallurgy, 1933. The Oxide Plant is divided into five main operations as follows: (1) Crushing, (2) Leaching, including dechloridizing and sulphur dioxide treatment, (3) Tailing disposal, (4) Electrolytic precipitation, (5) Smelting and melting. Crushing The present Primary Crushing Plant has been in operation 25 years, during which time 4,342,112 cars of 70 tons net capacity have passed through the dumpers. The ore as received from the mine is frequently blocky and up to 5 feet in section. It is reduced to 9-in. size by two 60-in. gyratory crushers, and transported to the east and west ore bins by 60-in. conveyors. In the secondary crushing operation the ore is first reduced to 2 to 3-in. size by five standard 7-ft cone crushers and two No. 10 gyratories. This product is then reduced to 3/8-in. size by fifty-two 48-in. vertical Symons disc crushers and is transported by belt conveyors to the loading bridges from which it is charged° into the leaching vats. Conveyor belt No. 14 which serves the eight vats in the east section of the leaching plant has transported over 125 million tons of ore, which is a record for any type of conveyor. This 60-in. belt travels at a speed of 600 fpm and carries loads up to 5500 tons per hr. Leaching The ore is leached in 14 vats, averaging 13,500 short tons net capacity each. These vats are lined with a natural mastic which adequately resists the sulphuric acid leaching solutions. The leaching process as presently conducted comprises soaking the ore with successive volumes of leaching solution and spent electrolyte and withdrawing successive volumes of enriched solution from the vat to a total of approximately 3.2 million gal. The first 1.6 million gal of this volume withdrawn is called strong solution and contains about 35 parts of copper per 1000. The balance of 1.6 million gal subsequently withdrawn is stored in a

Jan 1, 1952