Search Documents

By M. S. Burton, B. W. Christ, G. V. Smith

Evidence of the effects which high-angle grain boundaries and veining subgrain boundaries have on the yield phenomenon of zone-refined iron is reported. Room-temperature tensile tests on 50-mil wive at several gram sizes produced upon recrystallization at diffevent temperatures below 910C (a-y phase-transfornzatzon temperature) show that upper and lower yield stress decrease with increasing grain size. The upper yield point effectively disappears at grain sizes of 81 and 102 u in samples of this diameter. However, samples of 129 p grain size. produced during recrys-tallization at 950°C, exhibit a pronounced upper yield point and an increased lower yield stress. Possible causes of the reversal in the grain-size dependence of yielding are discussed. Veining substructure, detected with picval-HC1 etchant, but not with 2 pct nital, is formed during the a-y transformation, and is believed to account for the observed effecls. The strengthening associated with high-angle boundaries in zone-refined tron is discussed in terms of: 1) the stress dependence of slzp multiplicity, and 2) the stress dependence of dislocation emission from grain boundaries. WIDE use of transmission electron microscopy and dislocation etch-pitting techniques has led to a growing awareness of the presence of dislocation substructures in annealed pure metals. Whereas much speculation'-4 has developed about the influence which subgrain structures have on the mechanical behavior of metals, particularly the yield strength, only limited experimental evidence correlating subgrain structures with lower yield strength has been presented. 2,3,5-7 It is the purpose of this note to present experimental evidence of the effects which grain boundaries and subgrain boundaries have on both the upper and lower yield strength of zone-refined iron. Effects due to high-angle boundaries formed upon recrystallization below the a-y phase transformation are compared with effects due to veining subgrain boundaries formed upon "recrystallization" above the a-y phase-transformation temperature. These effects are further compared with the reported influence 2,3,5-7 which low-angle boundaries have on the lower yield strength of bcc transition metals. EXPERIMENTAL PROCEDURE The starting material for these experiments was a 1-in.-diam zone-refined ingot prepared at Battelle Memorial Institute. Initial purification of electrolytic iron by vacuum-induction melting was improved by a floating zone-melting treatment in ultrapure hydrogen.' Chemical analysis of this zone-refined iron appears in Table I. Tensile samples of 50-mil wire were prepared by rolling and drawing portions of the ingot. An intermediate recrystallization anneal at 625°C after rolling to a reduction in area of 85 pct was carried out in an evacuated Vycor capsule (10-=5 mm Hg). Further reduction in area of 91 pct was followed by recrystallization in evacuated Vycor capsules at temperatures between 600" and 950°C, see Table 111. All samples

Jan 1, 1967

By Y. Kondo, S. Yamazaki, Z. Asaki

Thermal deco7nposition of Pyrite particles in a fluidized bed with inert gas stream was studied. Assuming that heat transfer from the surroundings to the fluidized particles controls the overall decomposition rate, rate equations for the batch process and for the continuous process were derived. In the batch experiment, a linear rate equation satisfies the experimental results and the overall heat transfer coefficient calculated from the rate constant agrees fairly well with that obtained by Leva.l1 For the continuous process, two rate equations were derived, one on the assumption of complete mixing of particles and another on the upward piston flow of particles in a fluidized bed. The former holds for a bed containing a higher fraction of decomposed pyrite realized at lower feeding rates. The latter can be applied for a bed at higher feeding rates. Thus, segregation of particles in the fluidized bed was indicated at higher feeding rates. Bed temperatures also correspond to these conditions. ThERMAL decomposition of pyrite may be represented by Eq. [I]. The pressure of diatomic sulfur gas reaches 1 atm at about 690°C. The thermodynamics,' kinetics,2'3 composition, and properties3-5 of decomposed products of such a reaction have been studied. Pyrite is a very common sul-fide mineral and is often accompanied with other sul-fides. It is of basic interest in nonferrous metallurgy to clarify the behavior of pyrite in the pyrometallur-gical processes of sulfide minerals of metals such as copper, lead, zinc, nickel, and so forth. Interest in this reaction increased recently because of possible elimination of arsenic from pyrite in processing highly purified iron oxide pellets. Producing elemental sulfur from pyrite, instead of sulfuric acid, also aroused interest in this reaction. It is indicated that the thermal decomposition of solid particles, such as calcium carbonate, proceeds through three major sequential steps: heat transfer, interfacial chemical reaction, and mass transfer.637 It is known that the decomposed product of pyrite is very porous2, 3 and the diatomic sulfur gas evolved can easily escape through this layer of decomposed product. It depends upon the circumstances, therefore, whether the heat transfer to the interface within particles or the chemical reaction at the interface determines the overall decomposition rate. The enthalpy change in the decomposition of pyrite is about 33 kcal per mole FeS2 which is comparable to that of calcium carbonate. The decomposition of calcium car- bonate becomes more and more dependent on the rate of transport of heat when reaction temperature increases, such as occurs in a fluidized bed.6'7 It is reasonable to presume, therefore, that the thermal decomposition of pyrite, an endothermic process, carried out in a fluidized bed may be analyzed according to the heat transfer controlling model. This work intends, first, to propose a mathematical model that determines the overall rate in a fluidized bed for the decomposition process and, second, to investigate a few characteristics of the fluidized bed based upon the experimental results obtained. KINETICS OF THERMAL DECOMPOSITION IN A FLUIDIZED BED It is intended in this section to obtain rate equations for thermal decomposition of pyrite in a fluidized bed by assuming that the overall rate is determined by heat transfer from the surroundings to the particles. Both batch and continuous processes are considered. 1) Batch Process. To obtain the rate equation in the batch process, the following two additional assumptions are made. First, the temperature of preheated inert gas, tg, blown into the fluidized bed is assumed to be the same as the temperature of the fluidized bed, tf. Thus, no heat exchange occurs between the gas and particles in the bed and only the heat transfer from the reactor wall kept at tw to the particles is to be considered. Second, the decomposition is assumed to start at the outer surface of the particles and to proceed toward the center. At any given time during decomposition, undecomposed pyrite remains in the tori at a temperature: td. The decomposed shell is composed of FeS1+x whose outer surface is at tp Diatomic sulfur gas evolving at the interface is heated to tf during its escape through the decomposed shell. This is illustrated in Fig. 1. With the above-mentioned assumptions of heat transfer, we have:

Jan 1, 1969

Discussion of "The Ordering Transformation in Titanium-Aluminum Alloys Containing up to 25 at. pct Aluminum" by F. A. Crossley, Trans, TMS-AIME, 1968, vol. 242, pp. 726-30. Dr. Blackburn, in his response, pointed out that the c/a ratio of the Ti-26 at. pct A1 alloy quenched from 900°C is 1.6006 and not 1.5965 as plotted in Fig. 19. An error in transcription was made in preparing Table V of Ref. 1 (F. A. Crossley, Trans. TMS-AIME, 1966, vol. 236, p. 1174). The corrected Fig. 19 strengthens rather than weakens the argument that a martensitic transformation occurs in alloys containing from 15 to 18 at. pct Al. A Study of the Factors Which Influence the Rate Minimum Phenomenon During Magnetite Reduction, by P. K. Strangway and H. U. Ross, Trans. TMS-AIME, 1968, vol. 242, pp. 1981-88. Page 1883 Reverse Figs. 5 and 6. Sigma—Its Occurrence, Effect, and Control in Nickel-Base Superalloys, by J. R. Mihalisin, C. G. Bieber, and R. T. Grant, Trans. TMS-AIME, 1968, vol. 242, pp. 2399-2414. Pages 2403, 2407, and 2414 Arrows should appear on Figs. 4 and 9; a sigma is missing from Table IV; line 2, page 2414, change "case" to "cast". These are published correctly in the bound volume. Index, December Issue There were a few omissions in the Author Index. These have been corrected and published properly in the bound volume.

Jan 1, 1970

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By G. W. Form, W. A. Spitzig

The effects of hydrogen and vacuum shtering treatments on the physical and mechanical properties of arc plasma-sprayed tungsten were inuestigated. Temperatures examined ranged from 3000" to 4000°F in vacuum and 2000" to 3000°F in hydrogen for both single and duplex sintering cycles. Densities of 92 pct of theoretical density were obtained when a long-time hydrogen treatment at 2000°Fpreceded sintering in vacuum at 4000°F for 4 hr. This cycle also produced the highest ualues for modulus of rupture and bend angle. The results of this investigation point out the desirability of using a low-temperature long-time hydrogen treatment prior to a high-temperature vacuum sinter for arc plasma-sprayed tungsten. ADVANCES in the development of arc plasma-generating equipment have provided a high-temperature heat source that makes the fabrication of tungsten shapes possible by a metallizing process. Tungsten in the as-sprayed condition is very brittle. It has a density between 80 and 85 pct of theoretical density, a lamellar structure with elongated pores, and a high interstitial impurity content. To improve these properties, sintering treatments can be applied to the as-sprayed material, similar to those used for the densification of compacted tungsten powder. However, in view of the differences in the density and microstructure of as-sprayed tungsten as compared with compacted tungsten, responses to sintering were expected to be different. EXPERIMENTAL PROCEDURES The tungsten powder used in this investigation had a particle size varying from 3 to 13 p with an average diameter of 8p. The impurity level was less than 0.1 pct. The arc plasma spraying was done with an F-40 Thermal Dynamics Corp. plasma jet. Spraying was performed in air and thus required cooling of the substrate by an air blast in order to minimize oxidation. The spraying parameters employed in the fabrication of all specimens are listed below: Power input, kw 12 Arc-gas flow, cfh 95N2 + 5H2 Powder feed rate, g per min 33 Powder carrier gas flow, cfh ION, Spray distance, in. 3 Traverse rate, in. per min 30 Mandrel speed, rpm 100 Nozzle orifice, in. 7/32 These values of the spraying parameters correspond to optimum conditions ascertained in a previous study. Sintering was conducted at 3000°, 3500, and 4000°F in vacuum (< 0.1 Hg), and at 2000 and 3000°F in hydrogen. Duplex sintering treatments investigated are listed in Table I together with the designations that will be used for reference throughout this paper. The samples were fabricated by spraying onto a copper mandrel which was removed prior to sintering. The specimens used for the sintering analyses had the shape of small hollow truncated cones 1 in. high with an inside diameter varying from 0.500 to 0.125 in. and a wall thickness of 1/8 in. Specimens for bend testing were taken from hollow hexagonal prisms 1-1/2 in. high with a 1-in. diam across the flats and a wall thickness of 1/8 in. The bend-test specimens were ground to the dimensions 0.085 by 0.350 by 1-1/2 in. Prior to bend testing 0.0025 in. of stock was removed from each surface by electro-polishing. Density measurements were made by the water-displacement method. In addition, a porosimeter was used to determine the amount of interconnected porosity for representative samples. Strength and ductility were determined from recorded values in transverse bending using a cross head speed of 0.020 in. per min. The load was applied at the midpoint of a 1-in. span. The deflection data reported herein refer only to the plastic portion of the total deflection. RESULTS AND DISCUSSION The as-sprayed samples had a density corresponding to 83 pct (l pct) of the theoretical density of tungsten. Fig. 1 shows a representative as-sprayed tungsten structure.

Jan 1, 1964

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa.* May, &apos;71.. 1 3 2. Bethlehem. Pa Aug., &apos;71.. 1 10 8. Troy, N. Y Nov., &apos;71.. 1 1S 4. Philadelphia, PaFeb., &apos;72.. 117 5. New York, N. Y.*May: &apos;78.. 120 5. Pittsburgh, PaOct., &apos;72.. 125 7. Boston, MassFeb., &apos;78.. 128 8. Philadelphia, Pa.* May, &apos;78.. 2 3 9. Easton, POct., &apos;78.. 27 10. New York. N. YFeb.. &apos;74.. 2 11]

Jan 1, 1946

By Cyril Wells, Robert F. Mehl

THE practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out 1,13 This importance ties chiefly, though by no means only, in the study of carburizing and in the study of reactions involved in the eutectoid inversion in steel The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in y-Fe and their mutual effects are measured with precision The present paper reports the results of meas¬urements of diffusion coefficients D of manganese in -y-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients [$] Data on the rate of diffusion of manganese in y-Fe have been reported by Fry2 and by Paschke and Hauttmann 3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq cm per sec at 960°, which will be shown to be incorrect by many orders of magnitude Paschke and Hauttmann gave a rough value of 9 6 X 10-8 sq cm per sec at 1400° Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon METHOD AND MATERIALS Method -The method employed is identical with that used earlier 5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded The diffusion anneals were performed in argon, except one (test 18) in which hydrogen was employed for purposes noted below The temperatures reported are accurate to about 3° and constant within I°C , the diffusion times are reported to the nearest half hour The specimens were furnace-cooled after the diffusion anneal at about 2° per min Layers, usually 0 004 in thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0 01 per cent Mn, the distances of these layers from the interface was measured to ±0 0002 in The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions e The D values calculated by these two methods do not differ appreciably 5 The Grube solution was used except in tests in which the effect of concentration upon D was greater than 50 per cent, in such cases the Matano method, which explicitly provides for the variation of D with concentration,1 is the more reliable In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer In 3 of the 30 tests, however, this is not justified, and the D values

Jan 1, 1941

By L. R. Velho, N. A. D. Parlee, J. Gani

THE unsteady-state type of gas-liquid metal diffusion cell1 has found considerable application.2"4 Cells of this general design can function as steady-state cells if allowed to operate long enough to reach steady state. This report tells of some success in the adaption of this type of cell for steady-state work, using the 0-Ag system in which the mass transfer of the gas "species" is basically controlled by diffusion in the liquid. The gas, e.g-., O2, is maintained in the cell tube&apos;-3 at 1 atm pressure, Fig. 1, by buret and sensitive oil manometer. The gas, after diffusing through the stagnant metal, escapes at the annular metal surface around the tube at a lower constant partial pressure, in this case that of O2 in slowly flowing air, 1 atm.

Jan 1, 1970

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

HEAT-RESISTANT alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:12 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to 1.o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage II) of one per cent in ten thousand hours as extrapolated from rates per hour or tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at 1800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,1 in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably dose, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

By Chingyuan Y. Li, C. Y. Hsieh

Realizing that aluminum will have a great role to play in the coming industrialization of China, Chinese geologists have long been looking about for some aluminum deposits. The possible sources appear to be alunite, the alumina-rich shales, and the bauxite deposits. The locations of deposits are shown in Fig. I. Alunite Our attention was first directed to the alunite deposits along the southeastern coast of China. Table I summarizes the reserves now believed to exist in that region. Other alunite deposits have been found in Kiangpei, Szechuan province; Charming. Liuyang and Hsanshan, Hunnan province Tsingchow and Chowyuan, Shantung province. No reserve figures are available. High-alumina Shale Shale high enough in aluminum to serve as a source of that metal has been found in northeastern China(Tab1e 2). In Manchuria, the Manchuria Light Metals Co., at Antung and Fushun, operating under Japanese control, has been the only active producer of aluminum. It is not known, however, whether the company uses local raw materials or imports ore from elsewhere.* Shantung Bauxite Bauxite was first recognized in China at Paoshan, Shantung province. Although the reserve is reported to be large (estimated at 271 million tons), the high content of insoluble residue (SiO2) and mineral composition (diaspore) are dis-

Jan 1, 1948

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.&apos; However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By J. E. Drury, W. M. Byers, E. J. Lynch

Measurements made with starch ~~~~s indicate that the Presence of starch serves to depress the streaming potential of a clay mud system. Measurements with pure starch slurries show that the addition of NaCl or CaO reduces the streaming potential significantly. The addition of NaOH, however, causes only a minor reduction in potential even when there are large changes in mud resistivity. INTRODUCTION In their excellent study of the streaming potential, Hill and Anderson&apos; proposed that the presence of conductive solids within the filter medium will reduce the generated potential. This theory was demonstrated with measurements on shaly sandstone cores having various "b" factors; the cores with the higher negative b factors showed markedly lower potentials. (The factor b was originally defined by Hill and Milburn2 in an expression relating the resistivity of a shaly sandstone to the resistivity of the interstitial water: log F, = log F,, + b (log 100R,)&apos;. &apos;he factor b, therefore, is a measure of the contribution of the conductive solids to the total conductivity of the sample. It has been found experimentally to be directly related to the amount of chemically exchangeable ion per unit pore volume.) In the logical extension of this hypothesis to the streaming potential created by filtration through mud cakes, they suggested that the presence of nonconductive starch in a drilling mud would have the opposite effect; i.e., it would cause the streaming POtential to be increased. The high streaming potentials that they observed with lime muds were attributed to this cause. A cross-plot of some of their results which are relevant to this discussion is given in Fig. 1. The lime-mud curves and untreated-mud curve are taken from curves given in their paper. The gyp-mud line was estimated from their statement that the measured streaming potential for gyp muds in the range of 1.5 to 2.0 ohm-m was approximately 18 mv/1,000 psi. These gyp-mud potentials were the lowest that they reported for any of the bentonitic-clay muds, and were the only ones which were less than the untreated-mud potentials. This very low streaming potential of gyp muds has also been observed in field studies.&apos; By way of comparison, a U. of Texas publication4 gives the approxi-ate compositions for lime and gyp muds shown in Table 1. These materials are added to a bentonitic-clay mud base. It can be seen that both of these muds contain significant amounts of calcium salts and that the gyp mud has the higher concentration of starch. It would appear from this and from the data shown in Fig. 1 that starch may well be the cause of a streaming-potential reduction, rather than a potential increase. EXPERIMENTAL A series of streaming-potential experiments has been performed using a cell of a design similar to that reported by Wyllie.5 Calomel electrodes were used in both the mud slurry and the filtrate. Pressure in the cell was generated with high-pressure nitrogen. The primary objective of the investigation was to determine the effect of starch on the potential. Five different slurries were made which ranged in composition from untreated ben-tonitic mud (Baroid Aquagel) to a pure starch suspension (Baroid Im-permex). The intermediate slurries were prepared by mixing together a 9-lb/bbl clay mud with a 12-lb/bbl starch suspension in the ratios 1:3, 1:1 and 3:1. When starch was used alone, it was necessary to use an 18-Ib/bbl mixture, since leaner mixtures would not form a suitable filter cake. The clay mud used in the experiments was aged for three months before use. In addition to this series of measurements on the starch-clay mud mixtures, other experiments were performed to determine the effect on the potential of the absolute starch and Aquagel concentration, and the effect of adding various chemicals. RESULTS The effect of starch on the streaming potential is shown clcarly in Fig 2. Increasing percentages of starch resulted in n continually decreasing

By J. W. Walker, G. J. Heuer, E. W. Hough

An improved apparatus is described for the deterrni-nation of interfacial tension* by the pendant drop method in the pressure range from 15 to 15000 psi and the temperature range from 100º td 280°F. The chief characteristics of this apparatus are reliability and ease of operation. Temperature control was accomplished by means of an electrically heated jacket which could he completely removed while cleaning the apptrratus. The cell was designed so that the camera could he placed about I in, from the window without overheating the carnera lens. Separate "0" rings employed to seal each window and corresponding window backup plate gave very reliable window operation at 10,000 psi. An extra pistorr-cylinder combination was added so that a high compression ratio could he attained when gas was employed as one phase in the pendant drop cell. Other essential parts of the system were similar to an apparatus already described.&apos; The interfacial tension for carbon dioxide and water varies from about 69 dynes/cm at 15 psi to about 19 dynes/cm at 1,250 psi for 100°F. For pressure.r between t,500 and 3,500 psi, the interfacial tension is between 32 and 24 dynes/cm at this temperature. The interfacial tension at 280°F varies from about 50 dynes/cm at 200 psi to about 17 dynes /cm at 10,000 psi. The maximum surface excess for carbon dioxide, assuming the surface excess of water to be zero, occurs at about 1,500 psi jor the 100°F isotherni and Itas a value of about -79 X 1014 mol/sq cm. At 160°F this maximum IS shifted to about 2,000 psi and has a value of about 10 X 1014 111ol/.sq cm. Other maxima, us well as several minima, are present at these and other temperatures. Judging from the data on the solubility of water in carbon dioxide at elevtrted pressures2,3, it appears that the principal maxinza natned are in regions of increasing solubility of the water in the carbon dioxide rich phase. INTRODUCTION AND APPARATUS A pendant drop interfacial tension apparatus which would accommodate an opaque liquid in a gas phase was constructed several ycars ago&apos; for industrial purposes. This apparatus was used as a starting point for the present development. The objective of the present development was to enhance reliability and convenience of operation. Other articles&apos;" have described pendant drop apparatus which could not accommodate a gaseous phase adjacent to the windows. A schematic diagram of the apparatus is shown in Fig. 1. The water used followed the path; A, intro-

By Robert M. Keeney

Important recent developments in the melting and annealing of non-ferrous metals include: 1. Melting of nickel silver in the vertical ring induction furnace. 2. Electric melting of stereotype metal. 3. The rotary-drum gas-fired brass melting furnace. 4. The low-frequency coreless induction furnace. 5. Finishing annealing of brass sheets with city gas1 replacing wood in the large brass-rolling mill. 6. Electric annealing of brass and copper tubing and sheets. 7. Replacement of oil by gas and electricity in the annealing of nickel-silver shells and stampings. Melting Nickel Silver in Vertical Ring Induction Furnace Although over 90 per cent. of the output of the brass rolling mills in the United States is now melted in electric furnaces,2 until recently a considerable part of the output of nickel silver has been the product of the pit fire. The application of the electric furnace to the melting of nickel silver has been slow for several reasons: (I) Until recently no lining has been available that gave a satisfactory life in the vertical ring induction furnace when melting nickel silver; (2) the rocking arc furnace so widely used in the foundry does not appear to have been favored by the rolling mill for melting nickel silver, possibly because the gases present may affect the quality of the alloy; and (3) the exclusive rights to the use of the high-frequency coreless induction furnace (which has proved very satisfactory for melting nickel silver) for the wrought brass industry are controlled by one concern. A little over one year ago the first vertical ring induction furnace to be used for melting nickel silver in the Naugatuck Valley was placed in operation. This was followed by two more in the same mill, and by

Jan 1, 1930

By Leonard Greenburg

The American literature in the field of dust sampling and analysis has been growing rapidly since 1915. Studies made since that time clearly indicate that there are three fundamental factors that determine the production of lung pathology due to dust inhalation. These are the duration of exposure, the chemical and mineralogic nature of the dust and the concentration of the potentially harmful dust. In the estimation of the amount of the potentially hazardous dust there are essentially three problems involved: (I) a determination of the size of the hazardous dust; (2) determination of the most satisfactory apparatus and technique of sampling, and (3) the most satisfactory method of analysis. A complete study of the literature shows that industrial dust varies ill size from ultramicroscopic particles to those larger than lop in diameter and that relatively few particles are found over 5u in diameter. Approximately 10 to 25 per cent are less than 0.811 in diameter and the median size as a rule is found to lie between 1.25 and 1.75 microns. From the point of view of lung pathology the particle sizes of most importance lie between 0.5 and 5u. Of all the instruments for sampling dust the Impinger apparatus is the only one that will sample a larger body of air satisfactorily with small control errors and high efficiency in both low and high concentrations of dust. The Owens apparatus has the advantage of being more portable and somewhat easier to use but it does riot permit of the sampling of large volumes of air. It has a low efficiency in high concentrations of dust and does not permit dust weights to be obtained. From the point of dust-counting technique the author points out that in 1922 considerable experimentation with dark field and oblique illumination resulted in the conclusion that such methods were not readily duplicated from day to day and therefore yielded somewhat erratic results. Changes in the amount of illumination produced variations of several hundred per cent in dust counts obtained with dark ground

Jan 1, 1934

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield point of 16,000 lb. for pure electrolytic iron, one reaches a maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent;, a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated. Yensen observed an enormous drop in elongation and area reduction at about 2.65 per cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928

By Edward L. Vickers

The Pacific rim countries, comprising more than half the globe, represent a complex mix of developed and developing nations. The area comprises a large segment of the industrialized world. Within its boundaries are also found many of the world&apos;s greatest mineral resources largely concentrated in the less developed countries. The conflicting objectives of these developed and developing nations are giving rise to changes in the traditional patterns of world resource development. Powerful political and socio-economic factors affecting the world today are having a great bearing on natural resource developments in the Pacific basin. New forms of partnerships have been emerging in developing nations which have had a great impact on the mining com- munity, lending institutions, as well as political relations. The United States and Japan have been substantially responsible in the past for the development of natural resources in this area of the world. Their role, however, is undergoing significant metamorphosis. The rapidly changing economic and social environment in the developing countries is producing new tensions which affect future collaboration between producers and users of natural resources. To understand current problems, I believe, it is worthwhile to examine historical trends in this area which may help defining alternatives facing us in the future. In modern times the United States was the first country in the Pacific basin to start development of resources on a massive scale. It began with the major exploration of the mineral-rich west of the United States and extended significantly later into Latin America and Australia. In the early 1950&apos;s, Japan became a significant

Jan 1, 1976