Search Documents

By C. F. Allen, G. B. Walker

K. F. TROMP*—In dealing with the question of the most suitable kind of solid media for heavy density suspension processes Walker and Allen point out that the particle size of the solid media should not be taken too fine, as the viscosity increases with the area of the solid media and a low viscosity is essential lor high tonnage and accurate separation. A coarser particle size of the solid media will, in their opinion, of necessity give rise to a differential density in the bath (higher gravity at the bottom of the bath than at the top) but they advocate acceptance of the differential density rather than a higher viscosity. Though I fully agree with the choice the authors have made, I cannot subscribe to their view that only by accepting a differential density in the bath a coarse particle size of the solid media can be used. There certainly is another alternative: stronger agitation. Applying sufficiently strong vertical currents, a uniform gravity can be obtained quite well in a suspension of a coarse solid media. Of course, this is not a very attractive solution, for it means a degradation of the true gravity separation and a step backwards to hydraulic classification, which makes the washing dependent on size and shape of the particles. However, to a greater or lesser extent, this is what actually takes place in all the heavy density suspension processes relying on a uniform gravity in the bath. The so-called "stable" suspension processes make no exception. They all "stabilize" their suspensions by introducing or creating vertical currents, be it upwards or downwards or both, be it by hydraulic or by mechanical means. In fact, there is no such thing as a "stable" suspension in gravity separation, as the very reason for the use of suspensions in this field is the property that the solid media is able to settle and so facilitate the recovery. I have been enlarging on this point because the characteristics of the various processes can only be well understood and viewed from the same angle (from Bar-voys up to Chance) when the fact is recognized that mechanical or hydraulic agitation is a condition sine qua non for obtaining a uniform density from top to bottom in a suspension. Is a Cone-slraped Vessel Essenlial? Of the two alternatives for getting a low viscosity Walker and Allen have preferred correctly the sacrifice of uniform gravity in the bath instead of increasing further their vertical current arid agitation. The resulting differential density of the bath brings the problem of bow to prevent accumulation of intermediate gravity products in the bath, an accumulation which, if not prevented, would ultimately plug their cone. According to the authors an open-top cone combined with a downdraft current of the bath liquid would he the only suitable way to cope with such suspensions and they assume as a fact that "in any vessel other than a cone, such a differential density could not be tolerated." My experience is quilt: different. In my process, which has been in successful operation for more than a decade, differ-ential density of the suspension is applied ranging from values below 0.1 up to differentials above 0.5, according to the prevailing requirements of the individual plant. In this process, which is charac-terized by the use of horizontal currents in a suspension of differential density, the form of the vessel is of secondary importance and different types are in operation. It so happens that none of these are in the, form of a cone. The fact that 24 washboxes on my process have been installed and 12 others are under construction may constitute sufficient proof against the opinion that only a cone-shaped separator would be suited for differential density separation. Horizontal Currents in Differentia1 Den-sity Sepparation I myself have some doubts as to the suitability of a cone with downdraft for dealing with differential density (or, for that matter, any other washbox relying on vertical currents for removing the intermediate gravity products). It ap-pears to me that it is restricted to feed of small size only and even then with watch-fulness. If we take, for example, a piece of 2 in., the draft necessary to pull such a piece down to a zone wherein the den-sity of the suspension is, say, 0.03 higher, is quite considerable. For a suspension of, say, 1.6 sp gr the downdraft will have to be in the region of 3 in. per second. Unfortunately. most of the differential in density is in the part immediately below the reach of the top current which transports the floats. Consequently, we need the downdraft where we like it least: in the upper part of the cone. This entails the risk that light float particles are carried away with the downward current. This current of, say again, 3 in. per second would carry particles up to 1.3 sp gr and 3/8 in. size into the 1.6 gravity zone. This is prohibitive. It is also prohibitive because a downdraft of 3 in. per second in the upper part of the cone would require a tremendous circulation of medium. IIalf way up a 20 ft diam cone, a downdraft of 3 in. per second would correspond with 8500 gpm. With the downward current following the way of least resistance, the strength of the downdraft will not be exactly the same at different places of a cross area. If, as I anticipate, the center of the cone is favored, the strength of the downdraft will fall below the critical value near the

Jan 1, 1950

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By C. Norman Bowers, Blaine B. Wescott

Marked improvement in the serviceability of sucker rods has been effected in the last two years, partly because of the insistent necessity for greater economy in the operating costs of crude oil production growing out of the general industrial depression and partly because many of the recently developed fields have imposed more severe operating conditions upon both surface and underground equipment. The latter is particularly true of Kansas, where practically all of the oil produced is associated with damaging amounts of hydrogen sulfide brine and where the method of establishing potential production demands equipment capable of being operated at maximum capacity without interruptions. The decline of flush production in the Oklahoma City field created new problems in deep-well pumping on a scale heretofore unequaled and the increased proportion of water it has been necessary to produce in the fields of the Greater Seminole area presented conditions that were acutely in need of betterment. The problem in the latter fields was complicated by the shift towards sulfide characteristics, which accompanied water encroachment, and it is probably true that nowhere, at the present time, are pumping conditions generally as severe as in this territory. The Mid-Continent district, therefore, has become the proving ground for the numerous materials that have been proposed for sucker-rod fabrication. The information that ultimately will be obtained from an unprecedented amount of field experimentation will pay ample dividends when the decline of East Texas increases the demand for the vast reserves of sour crude in West Texas. It is a rare occurrence in industry that the use of such a simple piece of equipment as a sucker rod presents so complicated a problem for solution. As proof of this, it is only necessary to consider the numerous types of sucker rods on the market at the present time and contrast this condition with that of less than four years ago, when it was the common aim of manufacturers to develop a single sucker rod for all conditions of

Jan 1, 1935

By Robert S. Williams

On several occasions, when 60-40 brass is first obtained in the beta condition by quenching at about 825" C. and is then reheated, the writers have noticed that reerystallization will take place in the form of twin crystals at the grain boundaries of the original beta crystals. It was, therefore, thought that interesting results would be obtained if this twinning process was studied further, especially as to the temperature at which it first occurs. The material used in the investigation was a bar of extruded muntz metal, 1/2 in. in diameter, and of the following composition: Copper, 60.21 per cent.; zinc, 39.73 per cent.; lead, trace; iron, trace; tin, nil. Specimens 1 in. in length were sawed from this bar and a hole was drilled into the side of each specimen until it reached the center, and the tip of a platinum-platinum rhodium thermocouple was inserted. A small Hoskins' resistance-type electric furnace was used for heating the specimens. The specimens were first heated at 840' C. for 2 hr. and then quenched ' in cold water, in order to get the material entirely in the beta state. In every case, in the reheating process, the furnace was brought to the desired temperature before the specimen was introduced. The time occupied in preheating was from 20 to 30 min. By sawing back 1/4 in. on each side of the hole, two parts were obtained from each specimen and duplicate observations were possible. The specimens were held at the reheating temperatures for periods of 15 min., 30 min., 1, 2, and 4 hr. All specimens were etched with a freshly prepared mixture of equal volumes of concentrated NH4IOH and H2O2.

Jan 1, 1924

By J. N. Butler, R. J. Morris

A series of organic collectors has been developed which successfully float synthetic secondary uranium minerals, such as autunite, carnotite, and torbernite. Recoveries up to 97 pct have been obtained. With cleaning of rougher concentrates, ratios of concentration as high as 15:1 are possible on head assays of 0.10 to 0.50 pct U 3 O 8. Additions of certain base metal salts aid in recovery and materially increase the rate of flotation and selectivity of the collectors for the synthetic minerals. Flotation tests on natural uranium minerals have not yet equaled results obtained on the synthetics, although these collectors do give better results than conventional collectors for nonsulfide minerals. RAPID increase in mining and milling uranium ores during the past seven years and the discovery of large tonnages of uranium-bearing material too low in grade to stand the cost of leaching have developed considerable interest in possible methods for beneficiating these marginal ores. Such ores are generally classed as those containing less than 0.10 pct U3O8. Development of a beneficiation method that would give both high recovery and high ratio of concentration would also make possible the beneficiation of higher grade ores and would provide higher grades of feed to existing leaching plants. Although considerable research and testing on physical or physico-chemical beneficiation of domestic uranium ores has been done in the past, to the best knowledge of the authors only a single application of physical beneficiation is now in operation on a commercial scale. Flotation has been attempted on the basis of mineral association rather than by direct concentration of the contained uranium minerals. Flotation studies conducted on this project on certain ores gave recoveries of 60 to 70 pct of the uranium by the use of conventional flotation agents such as oleic acid, but ratios of concentration were in the order of 1.5:1 to 2.5:1. Subsequent cleaning to upgrade the concentrates rapidly increased losses in the cleaner tailings, which were not later refloated in the rougher flotation. Selection of Collector: In selecting desirable organic collectors for these oxide systems, a thorough study was made of the relationship between structural characteristics and collector activity by an examination of the behavior of a number of different functional arrangements present in a variety of organic molecules, (see Fig. 1). It is generally accepted that a collector must have a relatively long-chain hydrocarbon radical and a chemically reactive elec-trophilic center. Such a requirement could be met by a large number of compounds, but steric effects at the uranium mineral surface, solubility, compat-ability with aqueous systems, air avidity, bond strength at the mineral surface, interfacial concentration of the collector, and diffusion rate of the formed complex from the air-water interface eliminated many as unsuitable for this purpose. Preliminary investigations were completed of possible collector designs consisting of aliphatic and aromatic hydrocarbon radicals attached to stable combinations of nitrogen, oxygen, sulfur, and halogen electrophilic centers, Fig. 1.Tests were made to determine melting point spans, solubility of mineral-collector combinations in various solvents, reactions with soluble uranium salts, contact angles, and floatability by semi-quantitative beaker methods.' Contact angle determinations were not too useful because of the fine particle sizes of available mineral samples. From the foregoing study it appeared that nitrogen-sulfur electrophilic centers coupled with straight-chain saturated alkyl hydrocarbon radicals would hold the most promise for floating secondary uranium minerals. As the dithiocarbamate compounds can be made to combine these attributes they were selected for further study. The dithiocarbamates form a parallel structure to the xanthates, with the fortuitous exchange of

Jan 1, 1957

By R. M. Brick

THE Institute of Metals Division Lecture in 1936, given by R. F. Mehl, on diffusion in solid metals1, was introduced with the statement that "the phenomena of diffusion are intimately related to many basic prob-lems of the metallic state, but in addition to this the process of diffusion is of first importance practically." In view of the scope of that lecture, it does not seem necessary to review the importance, history or present status of diffusion problems. One aspect of the subject of diffusion that has received little attention became of some immediate importance in the course of a study on segrega-tion. When a solid solution alloy freezes, the familiar mechanism of solidification requires that the first nuclei formed be low in solute con-centration, with a resultant normal segregation or coring effect during freezing. Theoretically, diffusion of solute atoms during solidification should result in a homogeneous solid solution. Actually, of course, it is impossible in most binary alloys to obtain a cooling rate that will permit diffusion to eliminate coring in the freezing dendrites. For a given alloy, the extent of diffusion attained up to the point of final solidification will determine the degree of enrichment in solute atoms of the final liquid phase. The flow of this liquid into dendritic contraction channels and the solute concentration of the liquid seem to be the determining factors as to whether the final gross segregation is normal, inverse or absent. The purpose of the present study of diffusion was to determine to some extent the separate diffusion rates of copper and magnesium into pure aluminum with a view to clarifying previous results on segregation in these alloys; i.e., the fact that under similar freezing conditions alumimum-copper alloys segregate inversely and aluminum-magnesium alloys segre-gate normally. Of concomitant interest were the questions of the homogenization times required for segregated ingots or partially melted, i.e., "burnt," structures, and the solution heat-treatment times required for cast, hardenable aluminum-copper and aluminum-magnesium alloys, for worked and annealed structures, and so forth.

Jan 1, 1937

By John A. Mathews

RESEARCH in the steel industry, as in other lines of manufacturing, has for its principal purpose the increasing of profits. That is what manufacturing companies are for, and all departments of the organization must be so coordinated as to lead to profitable operation. To divide a payroll into productive and non-productive labor is misleading. Productive labor, in fact, is necessary labor, and non- productive labor is the labor we can get along without. One might as well say that the steering wheel is not a part of an automobile as to say that the directing minds of an industry are non-productive. Legitimate manufacturing profits in a steel company or any other company are the reward that the public pays for service rendered or risk taken. The desire for profits is the impelling motive that leads investors .to take risks and build up industries that give employment to others. Every department of a company, be it executive, manufacturing, financial, sales, or research, must contribute to the one end which brings success-profits.

Jan 1, 1921

By AIME AIME

UNQUESTIONABLY the Coal Division has never had a meeting in which so many outstanding technical papers were presented of immediate practical application to problems of personnel, mining, safety, preparation, combustion, and carbonization. Should there have been those present with the lingering idea that all that was needed for success in the coal industry was a strong back and a weak mind they must have had a rude awakening.

Jan 1, 1942

By U. K. Custred, E. W. Long, V. R. Degner

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. One approach towards increasing plant production capacity to meet the growing demand is through large-capacity flotation cells, provided they achieve metallurgical performance comparable to existing smaller cells. A 9-month evaluation test program recently completed at the Haynsworth mine at Bradley, Fla., demonstrated the feasibility of achieving economically acceptable concentrate grade and recovery levels using large, high-capacity flotation cells. The composition of the feed to the Haynsworth beneficiation plant is a typical Florida pebble phosphate matrix composed of phosphorite pebbles ranging in size from approximately 1-1/2 in. down to 150 mesh and intimately associated with a mixture of clay and sand (essentially silica). The feed contains approximately 22 to 28% phosphate reporting as tricalcium phosphate, Ca3 (PO,) 2, or "bone phosphate of lime" (BPL). The flotation section utilizes the double-float procedure typical of Florida plants. The phosphate is first floated away from the silica in the rougher circuit, using crude fatty acid, ammonia, and fuel oil or kerosene. Rougher conditioning is accomplished at 60 to 70% pulp solids with sufficient ammonia added to raise the pH to 9 to 9.5. Following coarse and fine rougher flotation, the concentrate (overflow) streams are joined and conditioned (sulfuric acid cleaned and washed) prior to entering the cleaner circuit where an amine float (cationic reagent and kerosene added in the feed box; pH 7.3 to 7.8) is employed to float the silica. The feed to the coarse rougher circuit averages 29% +35 mesh while the fine rougher feed averages 10%+35 mesh. Primary attention was directed toward the large rougher cell performance (recovery and grade) on coarse feed during the Haynsworth evaluation program. Flotation Cell Test Program A row of three No. 120 size (300 cu ft) WEMCO flotation cells was installed in parallel with an existing air-cell row. The total installed volume of the large cell circuit was 900 cu ft and required a floor space of 306 sq ft. This compared to the air-cell total volume of 200 cu ft and 152 sq ft floor space. (Both floor areas include feed and tails hoppers but exclude walkways.) Fig. 1 is a schematic cross section of the large flotation cell showing the relative location of key mechanism elements. In operation, the rotor generates a fluid vortex extending up along the walls of the standpipe and creating a sufficient vacuum within its core to ingest air into the standpipe/rotor cavity through the air inlet duct. The ingested air mixes with the pulp, which has been recirculated through the false bottom and draft tube, in the rotor. Further mixing occurs as the air and pulp move radially outward from the rotor, finally passing through the disperser into the flotation cell. Flotation is accomplished outside the disperser, where phosphorite laden air bubbles rise and the remaining pulp recirculates down along the cell wall to the false bottom and draft tube. Large-flotation-cell performance is influenced by the ability of the mechanism to (1) circulate, or suspend, the solids in the pulp; (2) ingest air into the rotor cavity; and (3) mix the air and pulp effectively. The proper balance between pulp circulation and air ingestion is a key consideration in achieving good recovery in a course feed application. Large-flotation-cell pulp circulation and air transfer characteristics are significantly influenced by rotor speed and rotor submergence; therefore, these two operational parameters can be used to "optimize" a particular mill application. Fig. 2 maps the hydraulic performance of the WEMCO No. 120 size flotation cell. This map can be used to relate the cell operational parameters which influence metallurgical performance. At a given rotor speed, power intensity (i.e., pulp circulation) is seen to increase, and airflow decrease, as rotor submergence is increased. The inverse relation between power and airflow is due to the two-phase air-liquid mixture density reduction accompanying the increased airflow rate. For any fixed rotor submergence, the power intensity (i.e., fluid circulation) and airflow both increase as rotor speed is increased. The selection of these two mutually related operating conditions (i.e., rotor speed and submergence) was a key consideration in the Haynsworth evaluation program.

Jan 1, 1976

By B. S. Gottfried

A generalized mathematical model is presented, which describes the thermal recovery of oil in linear systems with convective external heat loss. Three-phase fluid flow, conduction-convection heat transfer, chemical reaction between oxygen and oil and aqueous phase change are included, making the model applicable to a variety of thermal recovery processes. The complexity of the model requires that numerical solutions be obtained with a digital computer. The numerical approximations of the partial differential equations are presented and the algorithm is discussed in detail. The analysis is applied to the detailed simulation of a forward-combustion laboratory tube experiment. The results of the simulation exhibit with reasonable accuracy all of the principal thermal and bydrodynamic characteristics observed in the laboratory (i.e., the propagation of a combustion zone, a steam plateau, and oil and water banks). Numerical variations in the parameters appearing in the external heat-loss term, the aqueous phase-change term, and the Arrhenius combustion term are examined, and their effects on the predicted temperature profiles, oil and water production histories, and the air-oil ratio are presented. In spite of an oversimplification in the chemical reaction mechanism and the considerable computer time required to obtain solutions, the model represents a major advance in the ability to simulate the phenomena observed in thermal recovery experiments. INTRODUCTION Thermal oil recovery refers to a class of recovery processes where heat is supplied to a reservoir to provide the necessary expulsive energy. This thermal energy can be supplied externally as steam or hot water, or it can be generated in situ by forward or reverse combustion. In either case, however, thermal recovery processes are charac- terized by the simultaneous flow of two or three fluid phases in a variable - temperature field, accompanied by possible chemical reaction or phase-change effects.2-5, 7- 10, 14,16-18,20-22 Although a physical understanding of the thermal recovery processes is far from complete, it is possible to construct mathematical models which describe approximately all of the principal physical and chemical phenomena. However, attempts to solve such models, even with high-speed computers, involve formidable mathematical difficulties. Consequently, theoretical solutions have been obtained only for idealized cases in which important physical phenomena are neglected. For example, consider the process of forward in situ combustion. All such theories which have been developed consider only certain aspects of the process, such as heat transfer, 2-4,8,9,l6,l8 heat transfer with phase change,10 heat transfer with chemical reaction,7 or the hydrodynamics of three-phase flow.21 A general theory including all of the above phenomena has not been developed to date. This paper presents a unified theory of thermal recovery processes in linear systems. A mathematical model is developed which explicitly includes conduction-convection heat transfer with convective external heat loss, chemical reaction between air and oil, aqueous phase change, and the hydrodynamics of three-phase flow. A system of equations is developed which can be solved numerically on a high-speed digital computer, resulting in predicted temperature, pressure, and saturation histories in space and time. The model allows a more detailed simulation of thermal recovery tube experiments than had previously been possible. THEORETICAL DEVELOPMENT Consider the linear flow of gas, water and oil in a homogeneous porous medium. Assume that the oil will react with gaseous oxygen, and that mass is transferred between the water and gas phase by evaporation or condensation. In the absence of hydrocarbon phase change, intraphase diffusion,

Jan 1, 1966

By F. O., Garrabrant

ELECTRIC power requirements for Climax are similar to those of most metal mines, except that large blocks of power are used underground and there are a number of other unusual applications. Power is furnished to the Company by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are designed so that with the addition of forced cooling their capacity may be increased a third at 12,000-ft. altitude. On the secondary side of this bank is a 15-kv., 1200-amp. oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. (A more complete description of the electrical distribution system at Climax, with detailed drawings, is contained in T.P. 1734, A.I.M.E., Mining Technology, July, 1944.)

Jan 1, 1946

By Edgar Trask

EACH branch of engineering seems to depend on the cooperation and contribution of some other branches to enable it to produce more efficient methods and appliances for man to use. The purpose of this paper is to show approximately the gain in efficiency of self-propelled merchant ships when steel of greater elasticity is substituted for mild steel in some of the strength members and alu-minum alloy is substituted in some of the parts where strength is not essential. The new steel will have some greater strength and a much greater elastic limit in the as-rolled condition, and must be readily weld-able under ordinary conditions of shipbuilding. Naturally, its cost may be more than mild steel, but if the demand is great that excess cost may be reduced to an amount that will make its use more economical than that of the present mild steel. There appears to be a well defined axiom in engineering today that to use the least power to carry a given load the weight of the carrier must be reduced to a minimum. This minimum must be, of course, consistent with the necessary strength, rigidity and durability and it must not be attained at an excessive cost where the fixed charges of the carrier will exceed the savings in, operating the motive power. Recent railroad equipment is a notable example of this, and in these trains alloy steels and aluminum together with less weight per horsepower of the power plant are reducing the weight of the carrier and hence the total power required for moving the paying load. Before considering the application of these metals to shipbuilding, it is well to explain some of the fundamentals of ship design.

Jan 1, 1936

By H. W. McCue

In 1945 the number of oil wells drilled was less than in 1944 but the number of gas wells was greater. The oil wells numbered 176, completed for an initial production of 25,214 bbl., an average of 143 bbl. per well as against a total in 1944 of 245 drilled for 32,886 bbl., or 134 bbl. per well. All of these wells were in proven areas and no new discoveries

Jan 1, 1946

By V. K. Zworykin

THROUGHOUT its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes; it. has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron. Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction -at the very best a tenth-of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. To overcome it, a different imaging medium must be employed. The existence of such a medium became evident when it was demonstrated' that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed, Furthermore, although a wave length may be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light: Actually, the electron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. THE ELECTRON MICROSCOPE Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the electrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

THE Institute assembled in the rooms of the Geographical Society, Cooper Union, at 8 o'clock P.M., February 24th, 1874. President Barnard, of Columbia College, delivered an address of welcome, to which President Raymond responded. The Council then presented the following names, duly indorsed for election as members and associates. The gentlemen named were unanimously elected. *Bullock, M. C., - New York. †Burke, M. D., - Cincinnati, Ohio. *Burt, M. W., -Wheeling, W. Va. †Cameron, J. G. M., - New York. *Canfleld, Frederick A., - Dover, N. J. *Chandler, Prof. C. F., - New York. *Clayton, J. E., - Salt Lake City. †Colton, C. A., - New York. *Cooke, Prof. George H., - New Brunswick, N. J. *Cooper, Edward, - New York. *Dahlgren, C. B., - Mazatlan, Mexico. †Dutton, Capt. C. E., - Washington, D. C. *Eurich, E. F., - New York. †Fuller, H. L., - Woodside, Luzerne County, Pa. †Hamilton, S. Jr., - New York †Harnickell, A., - New York. *Hearne, F. J., - Wheeling, W. Va. *Hill, Samuel W., - Marshall, Mich. *Hulbert, Edward J., - Houghton, Mich. *Hunt, R. W., - Troy, N. Y. †lhlseng, M., - New York. *Iselin, Henri, - New York. *Janney, Morris P., - Pottstown, Pa. *Jenney, Frank B., - Brooklyn, N. Y. *Jenney, Walter P., - Brooklyn, N. Y. †Joy, D. A., - New York. *King, Clarence, - New York. *Kittoe, E. F., - Charleston, S. C. †Lawrence, Robert,. - New York. *Locke, J. M., - Cincinnati, Ohio. *McCormick, Henry, - Harrisburg, Pa. * Members. † Associates.

Jan 1, 1874

Discussion of the paper of Ralph Hayden, presented at the Butte meeting,. August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1443 to 1467. JOHN V. N. Done, Denver, Colo.:-Mr. Hayden has placed the metallurgical profession greatly in his debt .for this valuable paper. The importance of such a complete description of the research work on which is based the building of a plant to add at least 10,000,000 lb. of copper per year to the production of the Anaconda Copper Mining Co., at small expense, will be appreciated by all our members, and especially those who are facing similar problems. The information given in regard to the treatment methods discarded will be a great help to many workers, as it is often of as much importance to know what ? not to do" as what method to adopt. I Some further comment on the tests of the Dorr thickener may be of interest, as they have led to developments which I believe will prove of great importance. Before the Dorr thickener was installed, I had shown Mr. Laist reports from the Steptoe Valley concentrator, in which it was stated that one thickener 17 ft. in diameter was the equivalent in settling capacity of twelve 8-ft. cones, although the latter-contained double the surface area.. Mr. Laist, had made careful tests on the settling capacity of in 8-ft. cone on Anaconda slime, and we naturally expected the thickener would show a much higher capacity for equivalent area. When, is Mr. Hayden stated, the tests showed no increase, I realized that we were comparing it with a cone under test conditions, while the Steptoe results were based on operative conditions, find the explanation given by Mr. Waddell for the great difference had been, that " there is only one unit to watch instead of twelve, without the constant result of feed to twelve cones becoming unbalanced. Also the one 1 1/8-in. spigot used on the Dow requires no attention compared with the dozen 3/8-in. spigots of the cones.' I realized also as a. result of the tests that the total settling area required to handle the immense tonnage of the Anaconda company would be enormous, and very expensive in view of the housing required by Montana climatic conditions. After studying the matter over, I told Mr. Laist that I believed a thickener operating in a much shallower tank would have nearly the same capacity. I asked him to test it out in the same tank filled 3 ft. deep, and stated that if my idea

Jan 11, 1913

By Edward Keller

(Canal Zone Meeting, November, 1910.) UNDER the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which was described how multi-manipulations, in a works-laboratory, and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit in, or withdraw from, a muffle a set of 48 cupels as one unit. The front row. (8) of these. are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cupels. This operation is an enlargement of what I have already described in my former paper, and Fig. I shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath was designated as being convenient, but was not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders may be removed from the boiling bath, and the acid or water poured off from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Fig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper. ' Trans., xxxvi., 3 to 18 (1906).

Aug 1, 1910

By AIME AIME

REGISTRATION and licensing of engineers is now being given consideration by a special committee of the Institute, authorized at the March meeting of the Board of Directors. The subject is one that has recently been or is now actively before engineering organizations in many of the States of the Union. In Washington, D. C., the Washington Society of Engineers and the local sections of ten national engineering societies, including the A.I.M.E., recently had a joint committee investigate the subject: this committee formulating a proposed law that has been presented to Washington engineers for their consideration. At the same time, the committee has summarized the reasons for and against registration of engineers in Washington, D. C. As many of these reasons are of more than local application, they are here reprinted so that all members of the A.I.M.E. may be informed on the subject. It is expected that some report of the Institute's Committee on Registration, State Councils and Professional Development will he made at some forthcoming meeting of the Board of Directors.

Jan 1, 1932

By R. H. Richman

Coarse-grained Fe-Ni-C martensites formed at subzero temperatures were strained in compression at room temperature and the plastic deformation modes examined as a funclion of carbon content. At very low carbon levels, defovmation occurs hy wavy slip; commencing at about 0.05 pct C, mechanical twinning accounts for an increasing proportion of the plastic flow. Beyond approximately 0.4 pct C the deformation appears to be entirely by mechanical twinning. The habit planes of the operative twin modes were determined to be (113), (0131, and "(089)" in decreasing frequency of occurrence. Some of the implicaticms of Ihe o6served deformation modes upon the structure and properties of ferrous martensites are discussed. METALLURGISTS have long sought to explain the mechanical properties of ferrous martensites, particularly the extraordinary hardness and strength of the high-carbon varieties. Until recently the lack of precise knowledge of the structure of martensite crystals was the most serious barrier to understanding; however, the advent of thin-foil techniques for transmission electron microscopy has removed much of the mystery from martensite structure. Observations by Kelly and Nutting,"' and many others since, indicate that Fe-C based martensite crystals are internally twinned to a degree dependent upon the carbon content, and that a martensite plate containing 0.8 wt pct C or more consists of a stack of twin-related lamellae with each lamella on the order of l00A thick. Such a structure would be expected to influence greatly all aspects of metallurgical behavior, and many of the properties of Fe-C based martensites have been rationalized accordingly. Recent independent experiments led Winchell and cohen3 to conclude that the strength of ferrous martensite is derived primarily from solid solution hardening of the iron lattice by interstitial carbon atoms. Strength contributions from precipitation, dislocation-atmosphere interactions, clustering, short-range order, crystallite size, and so forth, were considered to be of secondary importance. In the view of Winchell and Cohen, the twinned structure of martensite serves mainly to limit the effective length of dislocation lines in the lattice, and thereby confers an added measure of hardening. Few properties of metallic crystals are as sensitive to metallurgical structure as are deformation mechanisms. It is somewhat surprising therefore, that, except for metallographic evidence of mechanical twins in strained martensite,4 no systematic examination of plastic deformation

Jan 1, 1963

The election of the following officers of the Council for the fiscal year 1919-1920, was confirmed by the Council on June 12th, 1919. President, S. E. Doane; vice-president, Wm. J. Clark; general secretary, Clarence L. Law; treasurer, L. B. Marks; directors, E. C. Crittenden, F. E. Cady, R. B. Ely. The membership of the Council for 1919-1920 will therefore be as follows: S. E. Doane, G. H. Stickney, George A. Hoadley, Wm. J. Clark, H. A. Horror, Otis L. Johnson, H. K. Morrison, Clarence L. Law, L. B. Marks, Adolph Hertz, S. C. Roger, P. S. Young, John C. D. Clark, Evan J. Edwards, James J. Kirk, E. C. Crittenden, F. E. Cady, R. B. Ely.

Jan 7, 1919