Search Documents

MEETING OF SAN FRANCISCO SECTION Twenty members were present at the meeting of the San Francisco Section, May 20, 1919. Chairman Bradley being in Alaska, vice-chairman, T. A. Rickard, presided. Prof. Frank H. Probert gave a short account of the activities of the governmental commission, consisting of himself, George S. Rice, and F. G. Cottrell, which recently visited Europe, and studied the coal, iron, salt, and chemical industries. When the work is finished reports will he issued. He gave a resume of the history of. the changes in nationality of Alsace-Lorraine and 'described the importance of the region for coal, iron, and potash. With the return of these provinces France will have an annual output of more iron ore than she has coke to smelt it with; hence, the importance of the Saar coal field. With these new mines France will take the predominant position in the iron and steel-industry formerly held by Germany. Many details were given of the devastated mines of France, and of their former value, production and the destruction that overtook them. Noteworthy is it that much of the damage was done as late as Oct. 28, 1918, for the express purpose of ruining the country industrially. The damaged area of the Valenciennes coal basin embraced twenty-four concessions, three were damaged by artillery bombardment, but have resumed operations since the' armistice, nine had their surface: equipment destroyed by battle, pillage, and sabotage, while twelve concessions at the eastern-end of-the field suffered from wilful, systematic destruction. Of the 285 shafts in the district, 172 were flooded either by: turning surface streams into them, or, by wrecking the cuvellage; thus, admitting water and quicksand from the water-bearing strata above the coal measures. Two hundred and thirty-five surface plants were damaged, many of them to such an extent that they must be scrapped. These properties gave employment to 135,000 men before the war and, even admitting the remote possibility of getting workmen, the terrible destruction and devastation makes housing and living a difficult problem. It will probably be from 3 to 5 years before the mines are drained and information obtained as to underground conditions; to attain the pre-war output may require from 12 to 15 years.

Jan 8, 1919

By J. W. Fuller

During the last 20 years, experimenters have sought to utilize pulverized coal in boiler plants, but refractory and slag troubles have usually overbalanced any gains in efficiency that were obtained. These troubles were caused largely by lack of knowledge of the proper methods of coal preparation and lack of a furnace design that would be adaptable to pulverized-coal firing. When this information was obtained the results were so much more satisfactory that within the last 5 years approximately 80,000 boiler hp. have been installed in plants ranging from 1000 to 20,000 boiler hp. rated capacity, which are operating at an average of 174 per cent. of rating. The first commercial installation for burning pulverized coal under boilers was made at the Parsons shops of the M. K. & T. railroad in 1916. Of eight 250-hp. water-tube boilers thus fitted, six were operated continuously for 3 yr., when oil was obtained at such a low price as to warrant its use. Since then, this plant has been operating alternately on pulverized coal and oil, depending on prevailing prices. Recently gas has been discovered within 20 mi. of this plant, so that this fuel may also be used. No change in furnace design was made when changing from pulverized coal to oil or gas firing. One of the principal advantages of this method of firing is its ability to utilize, with maximum efficiency, all kinds of coal, irrespective of quality or physical characteristics. In fact, quite a number of the present pulverized-coal installations were made for the purpose of utilizing coal that could not be marketed or used in any other way. The Pacific Coast Coal Co., at Black Diamond, Wash., formerly hand fired the boilers, using approximately 125 tons of prepared steam-size coal daily. The Black Diamond steam coal is the best quality of coal for steaming purposes mined in that section of the country, and there is a market for all that can be produced. By installing a pulverizing plant, it was possible to substitute coal of a size and quality that had no commercial value, so that 125 tons daily of the best steam coal formerly used at the mines is now marketed. This company made a similar installation, at its New Castle, Wash., mine with approximately similar results. Each of these two plants has a

Jan 1, 1922

By Albert Sauveur

Floris Osmond, Honorary Member of the American Institute of Mining Engineers, born in Paris, March 10, 1849, died at Saint-Leu near that city, June 18, 1912. Taken suddenly ill with congestion of the brain while on his way from Paris to his home, he reached it in time to write on the typewriter his last wishes, one of which was that no biographical notice of his life should be published. Holding Osmond's memory sacred, as those who have known him will, is it our duty to conform with his desire ? Shall no mention be made in our Transactions of the beautiful life and great achievements of one of our most honored members? Is it not, on the contrary, incumbent upon us to disregard Osmond's instruction in this matter and to place on record our admiration for the nobility of his life, for his talents and for the importance of his work, that younger men may be inspired by it with a desire to be guided by worthy motives in the path of unselfish pursuits ? I cannot feel that in following this course I am disloyal to Osmond's memory and I am strengthened in this belief by the opinion of men of high honor whom I have consulted before undertaking the writing of this obituary notice. One of them, Professor Henry M. Howe, justifies my decision better than I could do it myself when he writes : " Let us look frankly at the matter. Here we have a most extraordinary life, a life of rare beauty and power of inspiration to the rest of mankind. In my opinion we should not deprive mankind of the stimulating influence of the example of M. Osmond simply because he shrank from publicity. Our young men see every day how greed and vulgar push succeed, and with what material rewards they are crowned. They see too rarely the more valuable crown which comes to self devotion. A permanent and public recognition of the beautiful qualities of Osmond's life cannot fail to appeal to the imagination of young men and to help to deflect them toward leading a noble rather than a sordid life. Therefore I feel that the Revue de Métallurgie and other bodies owe it to the public to give prominence to his career by means of biographical notices."

Jan 1, 1914

By Frederick J. McGarry, Fred Moavenzadeh

An experimental investigation of the thermal and mechanical responses of rock materials to laser radiation is described. Specifically, the following three topics have been studied in detail: 1. Temperature measurements on thin discs subjected to laser radiation. 2. Strain measurements on thin discs subjected to laser radiation. 3. Observation and evaluation of cracking and spalling phenomena in constrained and unconstrained thin discs respectively, subjected to laser radiation. In conjunction with the experimental work done, use was made of a heat flow analysis and a stress analysis program developed for this purpose. It was possible to theoretically predict the thermal and mechanical responses of a rock specimen to laser radiation and then compare them with experimental observations. Good correlations were obtained.

Jan 1, 1971

By Charles F. Hickey, Eric B. Kula

Thermomechanical treatments applied to the maraging steels include a) cold working in the austenitic condition at 650°F, followed by transformation to martensite and aging, b) cold working in the murtensitic condition and aging, and c) cold working in the aged condition with and without subsequent reaging. The strength increases in these steels are very small compared to the increases observed in conventional carbon and alloy steels. The changes that are observed are compatible with the strengthening mechanisms operative during thermomechanical treatment of conventional steels, however. Differences are caused by the absence of a carbide precipitate and the low work-hardening rate in both the solution-treated and the aged conditions. ThE 18 pct Ni maraging steels represent a class of steels which are finding great interest for high-strength applications.1~2 They are essentially carbon-free, and contain 7 to 9 pct Co, 3 to 5 pct Mo, and 0.2 to 0.8 pct Ti. Although austenitic at elevated temperatures, they can be air-cooled to room temperature to form a martensite, which because of the absence of carbon is relatively soft. On subsequent reheating age hardening occurs and strength levels of 250 to 300 ksi yield strength can be attained. These steels appear to be particularly suitable for studying the response to various thermome-chanical treatments for additional reasons other than the obvious one of attempting to improve their already attractive properties. Thermomechanical treatments can be defined as treatments whereby plastic deformation, generally below the recrystal-lization temperature, is introduced into the heat-treatment cycle of a steel in order to improve the properties. With an absence of intermediate transformation products on air cooling the maraging steels have good hardenability and hence can readily be cold-worked in the austenitic condition prior to transformation to martensite. Further, they can be worked in the martensitic condition prior to aging, and even can be deformed in the fully aged condition. Finally, it is of interest to compare their re- sponse to that of the more conventional alloy and carbon steels, where the role of carbides is important in the strength increase by thermomechani-cal treatments. The thermomechanical treatment of conventional steels has been the subject of a recent review.' I) MATERIALS AND PROCEDURE The steel used in this investigation was a commercially produced vacuum-melt heat, which had been rolled to 0.090 in. and mill-annealed. The composition of the alloy was as follows: 0.02 C, 0.08 Mn, 0.10 Si, 0.009 P, 0.009 S, 18.96 Ni, 7.34 Co, 5.04 Mo, 0.29 Ti, 0.05 Al, 0.004 B, 0.01 Zr, and 0.05 Ca. Unless otherwise stated the heat treatments used were the standai-d solution treatment at 1500°F for 1 hr, air cool, followed by a 900°F, 3 hr age. In this condition, the material exhibited 232 ksi yield strength and 239 ksi tensile strength. Mechanical properties were determined by Vicker's hardness measurement (20 kg) and by tensile tests on standard 1/2-in.-wide, 2-in.-gage-length sheet tensile specimens. Notch tensile tests were run using the 1-in.-wide NASA type, edge-notched specimen.4 Fracture-toughness determinations were made on 3-in.-wide, center-notched, fatigue-cracked specimens, following the recommendations of the ASTM Committee on Fracture-Toughness Testing.4 An electric-potential technique was used for measuring the crack size at the onset of rapid crack propagation5 which is necessary for calculations of Kc, the critical stress-intensity factor under plane-stress conditions. The critical stress-intensity factor under plane-strain conditions KI, was also calculated, using the stress at which the first observable crack growth occurred. 11) RESULTS A) Cold-Worked in the Austenitic Condition. The reported M, temperature for the 18 pct Ni maraging steel is about 310°F.1 Therefore, a temperature of 650°F was selected as suitable for rolling in the austenitic condition. Specimens were solution-treated at 1500°F for 1 hr, air-cooled to 650°F, and rolled varying percentages from 0 to 60 pct, at 20 pct reduction per pass. Tensile and hardness properties after aging at 900°F for 3 hr are shown in Fig. 1. The tensile strength increases from 253 to 271 ksi and the yield strength from 247 to 265 ksi as a result of a reduc-

Jan 1, 1964

By R. G. Knickerbocker

The copper smelter and refinery of The Messina (Transvaal) Development Co. Ltd., at Messina, South Africa, was erected in 1920 and 1921, but initial operations were deferred until late in 1922 on account of the collapse of the copper market in the interim. Because the anticipated production was to be only 20 tons of copper per day from a high-grade matte containing 60 per cent copper, and because the ore did not contain gold or silver in quantities sufficient to pay for separation from the copper bullion, it was decided to design the plant along lines quite different from the modern smelteries treating large quantities of sulfide ores carrying appreciable amounts of gold and silver. The plant was built, therefore, for the production of copper by the Nicholls-James process. By this method two-thirds of the copper matte produced was roasted in a Merton calciner and charged into a bath of the remaining one-third portion of unroasted matte in a reaction furnace. The original design was not only novel in providing for the Nicholls-James process, but also in comparison with new plants built elsewhere, because of factors inherent in the locality. Sources of supply for machinery were very remote; it takes three months after the placing of an order to accomplish delivery of machinery into Messina from the United States. Native labor was available at 30 to 40¢ per 8-hr. shift. These factors permitted plant design which provided no overhead cranes, no matte ladles, no slag pots or other usual mechanical means of transportation between departments. The design resulted in a compact simple plant with furnaces arranged close together and terraced so as to provide for gravity transfer of molten material from one furnace to another and for manual disposal of products. Fig. 1 shows the relative location of furnaces. The three furnaces are parallel on successively decreasing elevations. A superimposed feed floor was provided above the furnaces. All three furnaces were provided with coal-dust burners served from a Bonnot system of coal-dust transportation, and the waste gases were discharged into waste-heat boilers. A short trial of the Nicholls-James process developed several facts which brought about a decision to abandon the process. Owing to the

Jan 1, 1934

By J. L. Lehman, J. D. Sudbury, J. E. Landers, W. D. Greathouse

A full scale field experiment on cathodic protection of casing answers questions concerning (1) the proper criteria for determining current requirments, (2) the amount of protection provided by different currents, and (3) the transfer of current at the base of the surface pipe. Three dry holes in the Trico pool in Rooks County, Kans., were selected for cathodic protection tests. The three holes were in an area where casing failures opposite the Dakota water sand often accur in less than a year. Examination of the electric togs showed the wells to be similar to other wells in the field where casing in four of seven producing wells has failed. The three holes were cleaned out and cased with 75 joints of new 51/2-in. 14-tb J-55. Each joint was visually inspected and marked before it as run. The casing was bull plugged and floated in the hole 50 that the inside might remain dry and free of excessive attack. Also, if a leak occurred, a pressure increase could be observed on gawge at the surface. Extensive testing was done, including potential profiles, log current-potentid curves and electrode measurements from both surface and downhole connections. Based on these data, a current of 12 amps was applied to one well and 4 amps to mother. The third well was left to corrode. During the two-year period when the casing was in the ground, [he applied current was checked weekly, and reference electrode measurements were made about every two months. Three sets of casing potential profi1e.c were run. When the three strings were pulled, each joint was examined for type of scale formed, presence of sulfate-reducing bacteria, extent of corrosion nttnck and pit depth. Since the pipe was new when run, quantitative determination of the protection provided by current was possible. This is the first concrete field evidence to help resolve the many arguments about the proper method for selecting adequate current for cathodic protection of oilwell (-using. INTRODUCTION A casing string is run when a well is drilled. This pipe is supposed to protect this valuable "hole in the ground" for the life of the well. Often the casing does not last the life of the well; it is with these casing failures that this work is concerned. The cost of repairing a casing failure varies from field to field—from as much as a $30,000 per leak average in California to $5,000 per leak in Kansas. Additional costs other than actual repairs are also important. These include formation damage, lost production, etc. Casing damage caused by internal corrosion is important in some areas. Treatment normally consists of flushing inhibitor down the annulus, but further research is being done on control measures. The test described in this paper is concerned only with external corrosion. The problem of casing failure from external attack has appeared in several areas including western Kansas, California, Montana, Wyoming, Texas, Arkansas and Mississippi. Cathodic protection is currently being used in an attempt to control external corrosion. From reports in the NACE there are thousands of wells currently under cathodic protection. The quantity of current being applied ranges from 27 amps on some deep California wells to a few tenths of an amp being supplied from magnesium anodes on wells in Texas and Kansas. Considerable field and laboratory effort1,9,5,6 was exented on the problem of cathodic prctection of casing, and it became fairly obvious that this method could be used to protect wells. Early workers showed that current applied to a well distributed itself over the length of the casing and was not concentrated on the upper few hundred feet. Basic cathodic protection theory had shown that corrosion attack could be stopped by applying sufficient current. The problem resolved itself, then, into one of trying to decide just how much current was necessary. Various criteria were utilized in installing the many existing cathodic protection installations. These methods included the following. 1. Applying sufficient current to remove the anodic slope as shown by the potential profile." 7. Applying enough current to maintain all areas of the casing at a pipe-to-soil potential of .85 v.' 3. Applying the current indicated by a log current-potential (or E log I) curve." 4. Supplying the current necessary to shift the pipe to-soil potential .3 v." 5. Applying 2 or 3 milliamps of current per sq ft of casing."

RESEMBLING in some respects the enterprise at R Chuquicamata is that of the New Cornelia Copper Co. at Ajo, Arizona. Controlled from its inception by the Calumet & Arizona Mining Co., New Cornelia became a unit of the Phelps Dodge Corporation when the latter absorbed the Calumet & Arizona company in 1931. Both Ajo and Chuquicamata are situated in low mountains in extremely arid desert country. Both ore deposits consisted-the past tense is used advisedly because the oxidized ore has nearly all been mined at Ajo-of a horizon of leachable oxidized ores overlying sulphide or concentrating ore. The principal technical problem in each case was the development of a method for treating the oxidized ore. In both instances the capping of waste rock was comparatively thin and power-shovel mining in open cuts was the obvious method of exploitation. Nature had smiled on neither place in the matter of climate. Though Ajo does not have the persistent winds for which Chuquicamata is notorious, the comforts of living are largely artificial. And it is only fair to emphasize that at each place the mining companies have achieved remarkable success in providing these comforts. Of course, in point of size New Cornelia must be content with the inferior role. From May, 1917, when production was started, to the middle of June, 1930, the company leached 16,368,000 tons of oxidized ore, thereby virtually exhausting the ores of this class. Up to the same date, about 15,000,000 tons of sulphide ore had been mined, and a rough estimate gives 170,000,000 tons remaining in reserve. The total tonnage does not loom very large in comparison with Chuquicamata's billion tons; but it is exceeded by similar figures for only four of the Porphyry group.

Jan 1, 1933

By J. W. Hickman

INTRODUCTION RECENT work by the authors1 on the oxide films formed on alloys of titanium and zirconium with nickel and copper indicated that an investigation of the oxides which form on alloys of copper and nickel might permit the relative rates of formation and diffusion of the ions of. these metals to be determined. This binary system is of further interest since the alloys which form are of the solid solution-type over-the entire range. In addition nickel is much more oxidation resistant than copper. A comparison of the free energies of formation of the simple oxides which may occur on these alloys indicates that nickel oxide should be observed over the entire time and temperature ranges of oxidation for all alloy compositions.1 In. order for nickel oxide to predominate on the surface, it is necessary that nickel ions form and diffuse to the surface. Two factors which may influence the formation of nickel oxide may be the ionic sizes, where Cu+ is 0.96Å and Ni-++ is 0.70Å, and the charges on the ions. On the basis of size, Ni++ should diffuse more readily than Cu+ while on the basis of charge, Cu+ should form more readily than Ni++. According to Uhlig2 passivity to corrosion in an alloy appears at a critical composition which for copper-nickel alloys is related to the tendency of the d band of electronic energy states to fill with electrons. This composition in the copper-nickel alloys corresponds to 40 at. Pct nickel at which composition Uhlig2 (quoting La Que's data) states that the alloy system becomes passive. Magnetic and specific heat data indicate that the d band of copper-nickel alloys is filled at 6o at. pct copper or 4o at. pct nickel. Mott and Jones3 have shown that if, on alloying nickel with copper, one considers a copper atom to be identical with a nickel atom except for an extra electron (nickel -has the-configuration: 3d8 4s2 and copper: 3 d10 4s) then at 60 at. pct copper or 4o at. pct nickel enough electrons are contributed by copper to fill the d band of the alloy. At this composition the magnetic susceptibility approximates zero according to Grew.4 Although the electron diffraction data will not determine the rates of the several reactions which may occur during oxidation, yet a determination of the structures of the surface oxides may yield information concerning the relationships, if any, which may' exist between the oxide structures which form and that composition where the magnetic susceptibility approximates zero. It is quite possible, of course, that the mechanisms of the oxidation and corrosion reactions may be so widely different that no correlations between them may be possible. SURVEY OF LITERATURE The metals, copper and nickel, which are face-centered cubic, form solid solution alloys which are face-centered cubic with no superstructure for all compositions. Three oxides of nickel have been investigated structurally by X ray diffraction. Of

Jan 1, 1948

By H. DeWitt Smith

THE mine operated by the United Verde Copper Co. is situated near Jerome, Ariz., on the eastern flank of the Black Hills, at an elevation of approximately 5500 ft. (1676 m.) above sea level. The mine and the town of Jerome are located on a steep hillside, which slopes rapidly to the valley of the Verde River. The smelter town of Clarkdale is situated in the Verde valley 4.1 mi. (6.5 km.) distant in an air line from Jerome, and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel & Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 mi. long and has a compensated 4 per cent. grade. At Clarkdale, it connects with the Verde Valley branch of the Santa Fe R. R. The narrow-gage (36-in.) line of the United Verde & Pacific Ry. was, until 1919, Jerome's only rail connection with a main trunk line. This road connects with a branch line of the Santa Fe system at Jerome Junction, after traversing 26 mi. of mountainous country. From the time of its location, in 1876, until its purchase by Senator W. A. Clark, of Montana, in 1889, the United Verde mine was worked on a small scale and shipments of high-grade gold-silver ore were made from the surface workings. Until 1894, when the narrow-gage railroad to

Jan 8, 1920

By W. B. Braden

This paper presents a suitable method for predicting gas-free oil viscosities at temperatures up to 500F knowing only the API gravity of the oil at 60F and the viscosity of the oil measured at any relatively low temperature. The API pravity and the one viscosity value are used as parameters to determine the slope of a straight line on the ASTM slanaord viscosity-temperature chart. Then, knowing the slope of the line and one point on the line, the vrscosities at higher temperatures can be determined. The line slope correlations were developed at I00 and 210F since viscosity data are frequently measured at these temperatures. A procedure is given for predicting line slopes from measurements at other tetnperatures. A nomogram is furnished for solving the relationship. The correlation has been evaluated at temperatures up to 5OOF for oils varyzng in gravity from 10 to 33 " API. The correiution is applicable only to Newtonian fluids. Comparison at 500F of true viscosities and those predicted from values at 100F shows an average deviation of 3.0 per cent (maximum deviation of 6.0 per cent). Predictions from the values at 21 0F for the same oils how an average deviation of 1.5 per cent (maximum deviation of 3.4 per cent). INTRODUCTION Correlations have been developed by Beal' and by Chew and Connally' for predicting viscosities of gas-saturated oils at reservoir conditions. Each of these correlations requires a knowledge of the solution gas-oil ratio and the viscosity of the gas-free oil at the reservoir temperature. For temperatures below 350F, measurements of the gas-free oil viscosities can be made easily using commercially available equipment. In thermal recovery processes, however, reservoir temperatures well in excess of 350F are encountered. Viscosity measurements at such conditions are more difficult and time consuming and require modification of existing equipment or the construction of new equipment. Measurements are further complicated by the difficulty of handling highly viscous oils associated with thermal recovery processes. Therefore, it is desirable to have a correlation which allows accurate prediction of viscosities at high temperatures. A commonly used technique for predicting viscosities at high temperatures is to measure the viscosities at two lower temperatures, plot the values on ASTM standard viscosity-temperature charts and extrapolate to the temperatures desired. If either of the values is slightly in error, the extrapolated value can be significantly in error. To justify an extrapolation, three points are actually necessary. This procedure can consume much time, particularly with heavy oils. Considering the cost of viscosity measurements, it would be desirable to eliminate the need for direct measurements by having correlations which would allow viscosity predictions from other physical or chemical properties. Beal1 investigated the possibility of correlating viscosity with oil gravity at temperatures from 100 to 220F. While showing that a general relationship exists, he also found significant deviations. It is possible that correlations will be developed based on oil composition as more information becomes available. While not eliminating the need for viscosity rneasurements, the method presented herein requires that only one viscosity measurement be made. The API gravity must also be known. The theory is based on the fact that the viscosity of paraffins (high gravity) changes less with temperature than does the viscosity of naph-thenes or aromatics (low gravity). The gravity. therefore, is used as a parameter to determine the slope of a straight line on the ASTM standard viscosity-temperature charts. The correlation is applicable only to Newtonian oils, and deviations due to thermal decomposition and nonhomo-geneity cannot be predicted. Oils containing additives have not been evaluated. PROCEDURE Fifteen oils were used in developing the correlation; eight were crudes and seven were processed oils. Oil gravities varied from 9.9" API (naphthene base) to 32.7' API (paraffin base). The temperature range studied was 81 to 516F. Each oil used had a minimum of three viscosity measurements and each plotted essentially as a straight line on the ASTM charts. In all, 91 viscosity measurements were used in the correlation. Saybolt, rolling ball and capillary tube viscometers were used for the measurements. Viscosity data for Samples 1, 2, 4, 7, 10, 11 and 14 were obtained in Texaco, Inc. laboratories. The data for Samples 3, 5, 6, 8, 9, 12 and 15 were from Fortsch and Wilson,3 and data for Sample 13 were from Dean and Lane.' All data points used in the correlation are plotted in Fig. 1. It is seen that some of the viscosity values deviated slightly from the straight-line plots at the higher temperatures. Properties of the oils after exposure to the

Jan 1, 1967

By L. D. Mullins, W. R. Bartlett, R. H. Barham, W. L. Wahl

This paper describes an electrical model and its applicution to the analysis of four reservoirs in Saudi Arabia. The model has 2,501 mesh points and represents 35,000 sq miles of the Arab-D member. Details of modeling such as mesh size, control problems and standards of performance in matching reservoir history are discussed. The particular performance match achieved for the Arab-D rnember is presented. Details such as permeability barriers, aquifer depletion and iwerference between oil fields are given. The performance match realized in the Abqaiq pool is presented in detail. INTRODUCTION The resistor-capacitor network and associated control equipment described in this paper comprise an electrical analog of a reservoir system. Similar equipment has been used to study the transient response of reservoirs for many years. The unique feature of the model and application to be described is the extremely large size of the model and reservoir system, and the detail observed in simulating the reservoir with the model. The Arabian American Oil Co. first became interested in analog computers for simulation of oil reservoirs in 1949. Since that time, several models have been developed, each more elaborate and refined so that the reservoir system might be more closely simulated. The current model is the latest in a series designed, built and operated by the Field Research Laboratory of Socony Mobil Oil Co. in collaboration with Aramco. It has been and continues to be used to study the regional performance of the Arab-D member limestone reservoir. The Arab-D member is one of the Middle East's most prolific producing horizons.. THE MODEL The theory of simulating a reservoir system with an electrical system has been presented in the literature.1-5 Therefore, this paper will not discuss the theoretical aspect of the problem except to point out the correspondence between the fluid system and electrical system, as shown in Table 1. In general, the complete model is made up of input devices, output devices, central control and a resistance-capacitance (RC) network. At times, the RC network alone is referred to as the "model". However, it should be evident from the text which meaning is attached to the word "model". A discussion of the equipment follows. THE RESISTANCE-CAPACITANCE NETWORK The RC network consists of 2,501 capacitance decades interconnected through 4,900 resistance decades. The components are arranged to form a rectangular network of 2,501 mesh points in a 41- X 61-mesh array. Imposing the mesh grid system on the continuous reservoir system divides the reservoir into discrete areal segments. These discrete segments may be of various sizes. More precisely, the mesh size need not be uniform throughout the model. The RC network is fabricated in two sections which are connected at the top. An inside view of the "tunnel" formed by the two sections is shown in Fig. 1. The height and width of the tunnel are shown in the figure. Numerals appear along the bottom and along the back opening of the tunnel. These numbers denote the x and y co-ordinate positions of mesh points. Fig. 2 presents a rear view of one-half the model. The length dimensions of the model, as well as a rear view of the capacitor decades, are shown in this figure. The control dials used in adjusting the resistance and capacitance values on the model can be seen in the enlarged portion of the model shown in Fig. 3. The electrical capacity at any mesh point can range from 0 to 1.0 microfarads set to the nearest tenth of a microfarad. The electric resistance connecting any two mesh points can range from 0 to 9,990,000 ohms set to the nearest 1,000 ohms. External capacitors may be added to any or all mesh points if the need arises. The values of electrical resistance and capacitance are adjusted manually by manipulating the two types of decade units. INPUT EQUIPMENT A considerable quantity of equipment is used to control the input to the RC network. These input devices are

By G. E. Anderson

THE Asientos-Tepezala district is in the north of the State of Aguascalientes, about 30 miles north of the city of Aguascalientes, the capital. The district is reached by a standard-gage railway on the west side through the junction, Rincon de Romos, which is on the main line of the National Railways of Mexico from El Paso to Aguascalientes. The terminal is Tepezala. On the east side a narrow gage connects Asientos with the junction, San Gil, on the main line, Asientos to San Luis Potosi. Tepezala on the west side of the Asientos hills is about 2 miles from Asientos on the east side. The area between the two mining centers is separated by a low subued divide which forms the central part of the hills. The district is in a group of isolated hills surrounded by characteristic bolson plains. The hills rise above the surrounding plains about 6500 to 10,000 ft.; the highest peak is Alta Mira. The two mining districts lie somewhat upon the flanks of the hills at about the same elevation, 7200 ft. The district is an old one and has been known since early in the 17th Century when the mines were worked by the Franciscan Monks. Their mining operations which were limited to the oxidized ore above the water level, consisted chiefly in extracting silver from the Santa Francisca vein. To judge from the old workings and the remains of surface plant, the operations were on a large scale. By modern mining operations since about 1900, the various mines of the district have been one of the principal sources of ore for the smelter located at Aguascalientes.

Jan 2, 1926

By Lauren A. Wright

The principal talc deposits in California are in a 200-mile belt paralleling the state's eastern border. The southernmost deposits represent selective alteration of early pre-Cambrian (?) carbonate strata, and are associated with granitic rocks. Deposits in the Death Valley area are at or near contacts between late pre-Cambrian carbonate rocks and diabase sills. Those in the Inyo Range area are chiefly alterations of Paleozoic carbonate rocks and silica rocks. Most of the state's talc output is used in ceramics.

Jan 1, 1950

By D. E. Peacock, B. Harris

Thermal-expansion and electrical-resistivity measurements have been carried out below 400°K on niobium and two niobium alloys containing tungsten. For anonaly in the expansion us temperature curve below aboct 300°K. This reslt is consistent with an earlier obsercation that Young's modilus joy Cb-132 lms an unusiully strong -tenperati-e dependence below roon temperature. No anonulous behavior was observed in the resistiuity vs temperature curve for either alloy or in the magnetic susceptibility us tenperature curve for Cb-132. These results are disclssed in terms of various electronic and bonding theories of the transition metals and their alloys, but it has not been possible to reach any definite conclusion as to the cause of the results obtained. ALONG with investigations of the low-temperature mechanical behavior of niobium and its alloys, some of the physical properties of these materials have also been studied. In the work described here, thermal expansion and electrical resistivity were measured below 400°K for niobium and two of its alloys, Cb-132 and D-43. In addition, the magnetic susceptibility of Cb-132 was measured over the same temperature range. The alloys are representative of two distinct tion-hardened alloy such as might find service as a turbine blade, while D-43 (Nb, 5.3 at. pct W, 1.1 at. pct Zr. and 0.08 at. pct C) is a solution- and dispersion-hardened alloy, of considerably lower strength than Cb-132. which is a potential vane material. Their significant common feature is the presence of tungsten as the principal source of solution hardening. EXPERIMENTAL TECHNIQUES Thermal-expansion measurements were made with a quartz-tube dilatometer using baths of liquid nitrogen, liquid bromoethane, and a liquid polyalkylene glycol derivative to cover the range 80 to 400 K. Results are recorded as expansion relative to that of quartz, and the probable maximum error in any value of relative expansion. All, is about il pct. The metallurgical condition of the specimens, which were in rod form. will be discussed in the section dealing with experimental results. Resistivity was measured on recrystallized wires 0.030 in. in diam using a potentiometric technique. The same baths were used for temperatures between 80' and 400°K as were used for the expansion measurements. and in addition the resistance of D-43 and Cb-132 was measured at 4.2 K by immersion in liquid helium. The maximum expected experimental error in any resistivity value is about 3 pct and that in any change in resistivity about i0.05 pct. Temperatures in both sets of experiments were measured with liquid-in-glass thermometers with an accuracy usually better than 1°K. EXPERIMENTAL RESULTS 1) Thermal Expansion. In Fig. 1 is shown the relative linear expansion of recrystallized niobium. D-43. and Cb-132. The curve for Cb-132 is composed of results from several runs on three different samples. Two of the samples were annealed for an hour at 1500°C to cause recrystallization and the third was annealed for an hour at 2000'C to remove some mi-crosegregation of tungsten which was known to be present in the wrought alloy received from the manu-

Jan 1, 1967

By C. S. Blair

THE development of a geological department as an integral part of the Tennessee Coal, Iron & Railroad Co. in the Birmingham district, Ala-bama, in 1908 was an innovation probably unique for any mining organ-ization south of the Ohio River, At that time a few of the oil companies were starting geological departments, but there were no geologists among the larger industrial organizations. The Tennessee Coal, Iron & Railroad Co. had been a substantial producer of pig iron for many years and was just getting a start in the manufacture of steel products from the pig iron. It had large acreages of coal land, ore land and timber land, but there was lacking the detailed knowledge of the possible mineral resources of much (of its territory, and this territory at that time covered an area in the neighborhood of 500,000 acres in the states of Alabama, Tennessee and Georgia. Those responsible for the operations of the mining properties, not being familiar with the kind of help that might be expected from geologic work, were decidedly skeptical of the utility of the work. Therefore it was necessary to develop cooperation with the mining organization, by not infringing upon its functions, and by developing the work in such a manner as to demonstrate to the mining department its practical utility. In the first instance the man responsible for a mining operation is apt to assume the attitude that the geologist is a blockader, because the geologist, unfortunately, is obliged to point out difficulties in the carrying out of mining operations in the way originally planned. He points out the dangers of mining out one coal or metal seam at the ultimate expense of an upper or lower seam, and he develops structural features, such as faults and folds, which call to the attention of the mining operator diffi-culties in his future operations, which the latter had not anticipated. Eventually, however, -the value of having these data became ap to the Tennessee Coal, Iron and Railroad Co., and the operators not only welcomed the geological work and cooperated fully in its acquisition of essential information, but reached the point of asking assistance and advice; and complete coordination of the two activities has existed for many years.

Jan 1, 1933

By A. S. Yue

The interface morphology of the Mg-32 wt pct A1 eutectic has been studied in terms of the freezing rate, the temperature gradient, and the impurity content. For the impure eutectic it has been found that for a given temperature gradient a fast freezing rate favors the formation of a cellular intwface with sub-grain strucfure. This cellular interface can be changed to a planar interface of the same substructure either by decreasing the freezing rate or by increasing the temperature gradient. For the eutectic of highest purity, as purified by zme-refining, no cellular interface was found for any growth condition and only a planar interface with subgrain structure was observed. Furthermore, a layer of liquid adhering to the interface during de-cantation freezes with shapes and sizes of the phase particles different from those in the main eutectic solid. WHEN a molten metal or a binary eutectic liquid with zero freezing range is solidified unidirec-tionally, a cellular interface is usually formed-3 This interface is schematically represented by Fig. 1. The profile of the solid-liquid interface has a corrugated shape, as shown in Fig. l(a), while the decanted interface consists of cells, as shown in Fig. l(b). The cell boundary in a frozen eutectic is distinguishable from the cell interior by changes in particle shapes, as shown in Fig. 4. The formation of a cellular interface, according to Weart and ack,' is attributed to a layer of constitutionally supercooled" liquid generated at the advancing interface by the simultaneous rejection of an impurity by the two phases of the eutectic mixture, which then permits freezing over an appreciable temperature range. This concept has been further elaborated by Tiller, who predicts that even in the absence of an impurity the rejection of solute ahead of each lamella of the eutectic may promote the formation of a cellular interface. More recently, Chilton and Winegard, and

Jan 1, 1963

By R. M. Larsen

The Rocky Mountain region is defined with some variations for different purposes or by different organizations. For oil and gas development, Wyoming, Montana, Colorado, northwestern New Mexico, and Utah are included in the order of their apparent importance. Portions of adjoining states, such as North and South Dakota, Nebraska, Arizona, Nevada, and Idaho, arc attributary to this region, but have little or no oil or gas production. Nebraska and New Mexico are considered separately (see pp. 412 and 415), and most of the discussion in this report will be confined to Colorado, Montana, and Wyoming. Utah has produced about 200,000 bbl. of oil from the San Juan and Virgin fields, which are isolated and shut in at present. The Clay Basin field in northeastern Utah produces natural gas and distillate, and the Farnham field in central Utah produces carbon dioxide gas. Other Utah areas of some interest are listed in Table I. The Cedar Creek (Baker-Glendive) field in southeastern Montana extends into North Dakota, but is listed under Montana. The other states are in the main wildcat areas, and exploration in 1944 was at a minimum. However, geological and geophysical parties are reviewing them for further testing. Oil production in Colorado, Montana and Wyoming was 459,000 bbl. more than in 1943. Increases of 713,000 bbl. in Colarado and 731,000 bbl. in Montana offset a loss of 985,000 bbl. in Wyoming. This was the first decline in Wyoming since 1938. Field production figures and state totals are given in Table I. Total drilling activities in these three states and Utah increased from 687 wells making 1,442,511 ft. of hole in 1943 to 916 wells making 2,245,803 it. in 1944. Wildcat drilling increased from 163 wells making 331,193 ft. of hole in 1943 to 171 wells making 389,144 it. in 1944. These figures include all drilling wells making footage, not starts or completions, and represent an all-time high in drilling. The year 1944 witnessed the greatest concentration of seismograph activity that the region has had. The Rocky Mountain Oil Scouts Association reported that in 1943, the previous peak year, 91 crew months of work were performed; in 1944, the time was 254 crew months. About 67 per cent of the work was in Wyoming, 18 per cent in Montana, and 12 per cent in Colorado. Twenty-three blocks totaling 400,000 acres were reported assembled in Colorado, and 161 blocks totaling 4,000,000 acres in Wyoming. Information about other states was not given. Fourteen unit agreements were approved by the Department of the Interior, as compared with 13 in 1943. The 1944 agreements were all in Wyoming. In five of the unit areas, oil or gas discoveries were made, four were dry, and five were drilling Or pending' Oil companies find it advantageous to unitize blocks containing any proportion of public domain. Units for

Jan 1, 1945

By John B. Baker, Bernard B. Betty, H. F. Moore

For several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.l,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. Specimens The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.—The Bridgman method of casting single-crystal specimens was used.3 The specimens were cast to the shape and size shown in Fig. 1 (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

By John B. Baker, Bernard B. Betty, H. F. Moore

For several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.l,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. Specimens The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.—The Bridgman method of casting single-crystal specimens was used.3 The specimens were cast to the shape and size shown in Fig. 1 (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938