Search Documents

By H. A. Saller, F. A. Rough

Studies of the V-U system have been made to determine the constitutional diagram. The diagram is fairly simple, since no intermediate phases are formed. Additions of vanadium lower the uranium melting point and allotropic transformation temperatures. The maximum solid solubility of vanadium in uranium is 12 atomic pct and the maximum solid solubility of uranium in vanadium is about 4 atomic pct. WITH the advent of high purity iodide vanadium,' it became of interest to study the alloying characteristics of vanadium and uranium. Alloys were prepared covering the entire system and were studied using a combination of metallographic examination and thermal and X-ray analyses. As a consequence of this work, the V-U constitutional diagram was evolved. In order to prepare suitable alloys for equilibrium-phase studies, it is desirable to have the purest possible starting materials. For this investigation, calcium-reduced vanadium, de Boer process crystal-bar vanadium, and good Mallinkrodt Chemical Co. uranium were used. The first work was done using the best vanadium then available, that being calcium-reduced vanadium produced at Knolls Atomic Power Laboratory. Subsequently, the important features of the diagram were checked using alloys made with crystal-bar vanadium produced at Battelle. These checks are in agreement with the earlier work. Analyses of the starting materials are contained in Table I. Only minor amounts of any impurities were present in either the vanadium crystal bar or uranium. Nevertheless, care was exercised in selecting the uranium for the alloys. The procedure followed was to section the stock into suitable pieces for melting, and macroetch each piece. Only those pieces which appeared to be clean by macroetch examination were used for alloying. Experimental Procedure Melting: Alloys with 0 to 50 atomic pct V were induction melted in beryllia (BeO) crucibles under vacuum of 10 microns pressure or better. A number of remelts was frequently required to insure uniformity of the individual ingots. Although no visible reaction between the alloy and crucible was found in any of these operations, the alloys were checked by spectroscopic analysis. Only trace amounts of beryllium were detected in the alloys. Alloys containing 50 to 100 atomic pct V were arc melted in a water-cooled copper crucible under an atmosphere of helium. A tungsten electrode was used. Ingots of 10 to 15 g were produced readily by turning and remelting a few times. Such small ingots were necessary because high purity vanadium was not available in appreciable quantities at this time. After melting, the ingots were examined metal-lographically for segregation and were consolidated by remelting before fabrication was attempted. Spectroscopic analyses showed that only small amounts of tungsten were picked up during the arc-melting process. Fabrication of Alloys: Alloys containing up to 20 atomic pct V could be fabricated by rolling in air at 600°C with 5 min between passes. After each pass through the rolling mill the alloys were returned to

Jan 1, 1954

By P. V. Brough, K. B. Gillaspie

DECISION to build a mill at the Bayard property was made in May 1942. Western-Knapp Engineering Co., of San Francisco, assisted by engineers of U. S. Smelting, handled the design and construction. Much of the milling equipment was moved from the Company's mill at Goldroad, Ariz. Wartime restrictions necessitated wood construction and paper sheathing except for structures adjacent to the Bullfrog shaft. Construction started in September 1942 and milling in March 1943. Bayard ores are processed in a single-ection mill. About half of the ore treated during the past year was hoisted through the Bullfrog shaft and the rest was trucked from other shafts. Coarse storage includes four bins, two of 120 tons each for Bullfrog ores and two of 85 to 120 tons each, served by a truck ramp. The low capacity figure refers to

Jan 1, 1948

The Institute makes liberal provision for inclusion of engineering students through individual Student Associate membership. Such members pay $2 per year, receive MINING AND METALLURGY, may purchase Technical Publications at reduced rates, have the privilege of attending all meetings and are furnished a distinctive badge in the form of a watch fob. Provision is also made for the affiliation of organized student societies in recognized schools of engineering chemistry, geology and related sciences. In order to qualify for affiliation it is not necessary that all members of the society become Student Associates since the individual members of the society are not listed as members of the Institute However, a large majority of the members of many of the societies are also Student Associate Members of the Institute. Among the things that the Institute does for the affiliated societies are the following: (a) A copy of each issue of MINING AND METALLURGY is furnished to the society; (b) Reports of the meetings and activities of the society are reported in MINING AND METALLURGY; (c) Assistance is given by the Institute in obtaining speakers for the meetings of the society; (d) The name of the society and of its officers is listed in the annual Directory and other publications of the Institute; and (e) Members of the society are given the use of the Engineering Societies Employment Service. Student organizations, desiring to be recognized as affiliated student societies of the Institute, should make application to the Secretary, giving particulars as to the nature of their organization, of their membership, and their officers. The accom¬panying list on page 24 gives the names of the affiliated student societies, their presi¬dents and their secretaries, as of April 17, 1931.

Jan 1, 1923

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Oscar E. Harder

THE TERM "physical metallurgy' is used in the title of this lecture in preference to "metallography ?because the former has a broader meaning with most audiences, some people thinking of the latter as being limited to work with the microscope. This distinction, how- ever, has not been held by the out- standing workers in the field of metallography, such as the late Professor Sauveur. In the broadest sense metallography is essentially the same as physical metallurgy. The American Society for Testing Materials has adopted-the following definition: "Metallography is that branch of science which relates to the constitution and structure, and their relation to the properties of metals and alloys." This definition might be improved by adding after "properties" -"and their industrial and scientific uses." Metallography has also been defined as the science of metals and alloys. Physical metallurgy is to be distinguished from process metallurgy in that the latter relates particularly to the production of metals from the ores.

Jan 1, 1940

By Blamey Stevens

(San Francisco Meeting, October, 1911.) My previous paper is entitled, The Laws of Igneous Emanation Pressure. The present paper lays no claim to the exactitude and completeness of a law, since it is of a provisional nature and may be disregarded when experiments have established a basis for more exact reasoning. The general physical states in which aqueous emanations may occur are first considered. The possible physical conditions under which the mineral elements may occur in emanations are then discussed, and a classification of deposits, dependent on emanation, is proposed. A system of scientific experimental investigation is outlined, and it is shown that the physical and chemical properties of emanation may be exactly determined thereby. The investigation is urged as feasible and simple, and not necessarily requiring large and costly apparatus. It is the only step necessary to make possible the formulation of a complete set of laws of igneous emanation. Process of Emanation. In a rising column, magma ranges in temperature from 900° to 1,200°C. Exhalation must begin at some fairly great depth. What this depth may be we can only surmise, since no experimental evidence is available. Exhalation, however, continues as the magma flows upward, until at another level the occluded gases have all escaped. This depth is probably upward of 5,000 ft. (See Fig. 1.) All exhalations must come from between these two levels. As the whole emanation is the sum of the exhalations and residues, the residues must come from below the uppermost level. They will be most abundant when coming, from those parts of the intrusion which have solidified below the lower level.

Apr 1, 1912

By V. H. Wilhelm

WITH rapidly diminishing oil reserves: a great percentage of which are uneconomical at present prices, some of the existing methods of development and production will have to undergo radical re- visions to meet the changes continually taking place in the petroleum industry. Imagination in an engineer is a great asset. The fancy of today is found to be the realization of tomorrow, and with this thought in mind, there is here presented a more or less imaginative picture which, to my mind, has a meritorious basis. Directed drilling has reached a stage of accuracy sufficient to allow the prediction that this art will be used in the future development of oil structures, especially those \\,it11 thin sand bodies 'and steep dips. Directional drilling in a number of fields in California has gratifying results. Wells which practically laid pipe lines through the oil sands have enjoyed a greater drainage radius with a consequent greater initial and cumulative production. In one field where the vertical thickness of sands was approximately 550 ft., wells drifting at an angle as great as 55 deg. fro111 vertical had over 1100 ft. of perforated pipe in contact with these sands. These wells were, and are, remarkable for their great initial pro-

Jan 1, 1936

By Nathaniel Herz

PARTING of bullion before shipment to the mint had been considered by the Homestake Mining Co. at various times, but had never been attempted before 1933, be- cause the margin of profit appeared to be too small to warrant the complications in refining. When the gold standard was abandoned by the United States in the spring of 1933, however, parting of the bullion was decided upon. The method selected was the Miller or chlorine process, which consists of the passing of gaseous chlorine into a bath of molten bullion, converting all metals other than gold into chlorides, and remov-

Jan 1, 1935

By James P. Sloss

A PERMANENT assay office is commonly established as part of the general plant equipment of operating gold and silver properties, but during the development stage of a mine, the cost of such an office is usually so assay work must be done elsewhere. In most instances only a few samples will be taken each day, but if the mine is to be developed scientifically, the analyses of those samples will guide further development. Under such circumstances, the time element in assay returns is important, since the lapse between the taking of the samples and the receipt of results may determine the success or failure of a small-mine operator. The following description of fur-

Jan 1, 1935

By A. M. Beebee

IN the present century the coal and manufactured gas industries have been eclipsed in public interest by oil, natural gas, and hydro- electric energy, which have had the benefit of rapid development and novelty. I sometimes wish that our social- order were such that hydro power had been developed first, that the use of gas from coal had never been seriously considered, and that our domestic energy requirements were supplied by other fuels. Sup- pose the manufacture of gas from coal should then come on the scene at the present time with the current plight of the railroads, coal regions, and labor generally, presenting the fact that it could increase the amount of coal mined and shipped by the railroads by some 16,000,000 tons, and increase the coal used at existing u plants five times. Imagine the great public interest that would be manifested; it would supply the cooking and water-heating requirements of a community with a superior character of service at a cost to the customer approximately half that which had obtained previously. Would not such a situation be heralded as the salvation of our country and all help be given it?

Jan 1, 1940

By S. C. Dhara

A process of solvent extraction and separation of platinum group metals (PGM) and gold using primary, secondary, tertiary, and quarternary organic amines has been briefly described. The effects of amine structures; the use of diluents; the principle of synergism and antisynergism in the mixed extractants; the oxidation states of metal ions are explained in the amine extraction process of precious metals.

Jan 1, 1984

By R. C. Buehl, J. P. Morris

ACTIVITY values for sulphur dissolved in liquid iron and slags as functions of composition and temperature are needed in applying thermodynamics to sulphur-control problems in iron- and ' steel-making. The purpose of this investigation was to determine the effect of carbon on the activity of sulphur in the metal phase. The method employed was the same as that used in an earlier investigation' concerning the effect of silicon on sulphur activity in liquid iron. A study was made of the conditions of equilibrium in the reaction between hydrogen gas and sulphur dissolved in iron-carbon alloys. The chemical equation for this reaction can be written as follows: S (in liquid Fe-C alloy) + H2 (gas) = H2S (gas). It was found that the activity coefficient of sulphur in liquid iron increases as the carbon content increases. At 2.3 pct carbon and 1600 °C, the activity coefficient of sulphur is twice its value in carbon-free iron, and at carbon saturation it is more than six times as great. The effect of temperature on sulphur activity was found to be small. Previous work on the reaction between hydrogen gas and sulphur dissolved in liquid iron has been reported by several investigators2,³,4 but only recently have studies been made of the effect of alloying elements. Silicon1 is known to have a pronounced influence on the activity of sulphur in iron, its effect being similar to that shown by carbon as described in the present report. Kitchener, Bockris, and Liber-man5 recently have published a preliminary report of their work on the effect of carbon on sulphur activity in iron. Their experiments were made at 1570°C and carbon saturation in the melt. Under these conditions they found that the activity coefficient of sulphur was approximately doubled by the presence of carbon. This is a much smaller effect than that found in the present work. Experimental Method: The apparatus and procedure were essentially the same as those used in the earlier investigation of the effect of silicon on sulphur activity.' Briefly, the method was as follows: A molten iron-carbon alloy was brought to equilibrium at constant temperature with a mixture of H2 and H2S of constant composition by bubbling the gas through the metal. Samples of the melt were

Jan 1, 1951

A recent study estimates that a 10% improvement in the performance of wire rope used on draglines could save the US coal industry $2 million annually in rope costs. In addition, such an improvement could boost annual coal production by allowing the industry's draglines to remove an extra 1.5 million m3 (2 million cu yd) of solid overburden each year. These findings, although admittedly preliminary, suggest the magnitude of benefits that can be derived from a well-planned wire rope maintenance program.

Jan 3, 1978

By E. H. Crabtree

IN an ideal mill, with perfect milling operations, the mineral extraction would be 100 per cent, the, concentrate would be 100 per cent mineral, the tailing would assay zer.0 mineral and the milling cost would be zero dollars. Such an operation can, of course, never be attained. We can only strive to approach it as nearly as possible and in doing so most recognize .the fact that the three primary factors in milling: assay of concentrate, assay of tailing, and cost of operation bear a definite economic relationship to each other. This relation will change from time to time and will be different for different mills, depending on milling equipment, character and quality of feed, market conditions, and other factors. It is granted that for a given operation there is an economic point, but the location of this point is difficult. It is for the purpose of making some of these economic points a little more tangible that this paper has been prepared.

Jan 1, 1930

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemisorption.

Jan 1, 1950

By T. R. Wright

THE Corporation operates concentrators in four camps: Casapalca. Morococha, Cerro de Pa-co, and Mahr. The present concentrator at Cerro de Pasco is the newest having been completed in 1943. and that at Casapalca the oldest, having been built originally as a gravity concentrator, in 1889. Prior to 1925 the Corporation's milling operations were confined to the beneficiation of silver-bearing copper ores, and treatment of these ore: by flotation was started in 1918. Although fairly large deposits of complex, fine-grained lead-zinc ores existed, little progress had been made in the treatment of such ores--in Peru or elsewhere-until the early 'twentics. The Casapalca concentrator began the selettive concentration of complex leadzinc ores by all-flotation methods in 1925, or contemporaneously with the commercial development of selective lead-zinc flotation in the United State:.

Jan 1, 1945

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to iroth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkinsl reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon-hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group. In this paper, a surface components hypothesis is Proposed to explain the different floatabilities of coals, carbons, and hydrocarbon minerals. The validity of the hypothesis is experimentally supported by the actual floatability, natural floatability, wettability, and adsorbability for neutral oils of coals, carbons, and hydrocarbon minerals tested. The combustible recovery of the flotation results, as used in this paper. was calculated from Eq. 1: P (100-Ep) 100 RWCP Rc= [1] F (100-E,) C, where R, is the percent combustible recovery; F and P are, respectively, the weight of feed and the weight of concentrate or product; E, and Ep are, respectively, the total percent of ash plus moisture in feed and in concentrate; Ru. is the percent weight recovery: and C, and C, are, respectively, the percent of combustible in feed and in concentrate. Except for ash and moisture content, all chemical components of a coal are assumed combustible. The experimental work included studies on flotation, ultimate and proximate analyses, contact angle tests, extractions of bitumen-A with benzene, adsorptions for liquid hydrocarbons, and wetting tests. Most of the flotation experiments were performed in a laboratory Fagergren machine; others were tested in a small Denver machine. The solid feed for the former was 300 g and for the latter was 30 g. The solid materials used for flotation were crushed to —48 mesh. After the mineral pulp in the flotation cell was agitated for 6 min and the pH was adjusted to 7.5 & 0.2 with sodium hydroxide or hydrochloric acid, a petroleum light oil having a viscosity of 5.73 centipoises at 77 °F was added and conditioned for 2 min. Finally, pine oil was introduced and the froth was collected for exactly 3 min. The weight ratio of petroleum light oil to pine oil was kept constant at 1.5 to 1. Tap water was used for all flotation tests. Contact angles were measured with a captive bubble machine. For each coal sample, three specimens were mounted in transoptic mounts and polished with levigated alumina, first on a sheet glass, then on a cloth-covered metal polishing wheel. The polished specimen was first washed with distilled water and wiped thoroughly on a cleaned linen pad, then transferred into the pyrex cell of the captive bubble machine and conditioned for 6 min., and finally measured for contact angles at three or more points. Except where otherwise stated, the induction time for each measurement was 1 min. The contact angle representing each material was obtained by averaging the measurements of three specimens. The linen pad was first washed with warm distilled water, then boiled 30 min in a 2N sodium hydroxide solution, and finally washed with distilled water until no trace of sodium hydroxide could be detected in the decanted solution. The cleaned linen pad was stored under distilled water. Immediately before using, the pad was rewashed and transferred into a clean pyrex petri dish partly filled with distilled water. The glassware and rubber gloves used were cleaned by soaking in sulphuric acid-potassium dichromate cleaning solution, followed by rinsing with distilled water. The polished specimens were handled only by glass forceps. The ultimate and proximate analyses were made in accordance with the ASTM standard procedures for coal and coke. The extractable bitumen-A was determined by weighing 1 g of —100 mesh sample and placing it in a desiccated and weighed ASTM aluminum-extraction thimble. The thimble was placed in condenser hooks and inserted into an extraction flask containing 100 cu cm of benzene. The flask was heated and the benzene vapor was condensed by water coils. At the end of 24 hr of percolation, the thimble was removed, desiccated, and weighed. Loss in weight of sample was taken as bitumen-A and calculated to dry and ash-free basis.

Jan 1, 1955

By Arthur R. Kommel, Robert F. Mehl, Gerhard Derge

The orientation relationships resulting from allotropic transformations and the formation of segregate structures in metals and alloys have been the subject of the eight earlier papers in this series'. A brief summary of orientation studies has also been given by Sachs2. A survey of these papers discloses that the factors that determine the orientation relationship of a precipitated phase to its parent solid solution, as well as the outward form and appearance of the new phase, are not completely understood. It is now evident that crystallographically analogous systems, as a rule, exhibit the same type of Widmanstatten figure and orientation relations, so that useful information is not to be expected from examination of a new alloy involving lattice combinations of which the orientation relationships are already known. Therefore, the determination of the relations existing between lattice types that have not already been studied seems to be the most promising mode of attack upon the problem; both of the systems reported in this paper represent new combinations of lattice types. A. The Mg-Mg2Sn System The magnesium-tin equilibrium diagram given by Hansen3 shows the phase Mg2Sn to be the only intermediate phase. The solid solubility of Sn in Mg decreases from 14.8 weight per cent at the eutectic temperature, 561' C., to 2.3 per cent at 450°, while no solid solubility of Mg in Mg2Sn has been observed. The crystal structur: of Mg is close-packed hexagonal with a0 = 3.202 A. and co = 5.199 A.4, while Mg2Sn is of the CaF2 type with a. = 6.78 A., with four molecules in a unit ce115,6. Alloys from two different sources have been used: (1) those supplied by the Dow Chemical Co., which contain 6 and 8 weight per cent Sn, and (2) those prepared in this laboratory, containing 8 and 13.5 per cent Sn. The latter were made from Dow high-purity Mg and Baker chemically

Jan 1, 1937

By Oliver C. Ralston, James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each of clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1940