Search Documents

By Martin A. Moyers

THE nation's effort to win the war speedily is reflected in current trends in coal utilization, as in all other fields of our lives. In all industries, wherever coal is used for the production of heat and power the emphasis is on getting the most useful result with the least expenditure of matt.ria1. In addition to carrying its own share of the load, increased as it is by the demands of war industry, coal has had to fill in for the other fuels, mainly petroleum products, whose distribution from their more distant sources has been crippled by lack of shipping. Thus, the outstanding note in the utilization of coal this year is not the development of new methods of burning or handling coal but the extraordinary job that the industry has done in producing enough coal to serve all needs.

Jan 1, 1943

By AIME AIME

A CERTAIN area in the State of Indiana seems to be a breeding place for presidents and near president about eighteen miles southeast of Elwood is the little village of Daleville, and there, on April 9, 1890, John Robert Suman, newly elected President of the A.I.M.E., was born. It was not long before he migrated to California, however, where he went to the Los Angeles High School, then for two years to the University of Southern California, after which he went up to Berkeley

Jan 1, 1940

By K. G. Davis, P. Fryzuk

A study has been made of the effect of undercooling on the grain structure and solute distribution in small ingots of pure bismuth and of a 100 ppm Ag in bismuth alloy. Autoradiographic evidence shows that in undercooled melts a network of dendrites is formed throughout the melt immediately after nu-cleation. At large undercoolings the dendrites are very thin and closely spaced. The origin of the observed grain morphology can be explained on the basis of information about the mode of solidification revealed by the impurity substructure. WHILE a great number of studies of nucleation in undercooled molten metals have been made, comparatively little attention has been given to the mode of solidification from melts with large undercool- ings. Colligan and Bayles1 and Walker2 have measured the rate of advance of the solid-liquid interface in undercooled nickel melts, but the morphology of the solidifying material remained a matter of speculation. Fehling and Scheil3 have described the grain structure in ingots formed from undercooled melts of nickel, palladium, and copper, and a series of Ni-Cu and Ni-Pd alloys. At small undercoolings, equiaxed structures are observed, the grain diameter tending to increase as the temperature of nucleation is lowered. At greater undercoolings, a columnar structure is developed, while with still further undercooling there is a smaller grain size incorporating rather coarse subgrains. All-bright and Colligan4 examined the grain structure shown by ingots solidified from melts of nickel and of Ni-Ag alloy at an undercooling of 105°C, and concluded that considerable grain growth had taken place after solidification. The object of the present work is to correlate the mode of solidification from undercooled melts with both the grain structure and impurity segregation, using tracers to examine the latter.

Jan 1, 1965

By F. B. Plummer

PETROLEUM ENGINEERING deals with the production, transportation, and refining of crude oil. Refining is chiefly the work of the chemical engineer; production, that of the petroleum engineer. Production engineering only is discussed in this paper. Petroleum production engineering is closest related to and, in fact, is a branch of mining engineering. Formerly, many petroleum engineers were trained as mining engineers or mining geologists. The profession is related also to mechanical and civil engineering to about the same extent that mining engineering is. Petroleum production draws upon the mechanical branch for drilling and pumping machinery and upon civil engineering for the construction of transportation lines, water supplies, and water-disposal plants. Fundamentally, petroleum production engineering deals with the removal of the oil from the reservoir rocks, just as mining is concerned with the removal of ore. The process of oil production demands a specialized knowledge just as distinct from mechanical and civil engineering as mining is distinct from operating a Diesel engine. Even though the chief tools of the petroleum engineer are the drill and the pump, these may be of little avail, and certainly not efficient, if their selection and use is not based on a knowledge of the physical chemistry of oil, the geology of the formations, the structure of the oil sand, the hydrodynamics of the reservoir, and the interrelation of all these many factors.

Jan 1, 1936

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world's produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

By L. G. Margolin

INTRODUCTION In this paper we derive an expression to predict the onset of growth of a crack in a quasibrittle material. We employ an energy criterion, which was first proposed by Griffith (1920), and is essentially equivalent to the first two laws of thermodynamics. The criterion is applied to the elastic-plastic crack of Olesiak and Wnuk (1968), which is a three-dimensional generalization of the Dugdale (1960) crack. Our expression for the onset of growth differs in several respects from a criterion based on a crack in a brittle material (i.e., using linear elastic fracture mechanics) . Furthermore, the new features are in qualitative agreement with the experimental data. Among these new features are 1) the dependence of the apparent surface energy, or critical strain energy release rate on crack size (the shape of the R-curve); 2) the effect of in-plane stresses (i.e., the stresses that do not lead to any traction on the crack faces) on crack growth; and 3) a brittle-ductile transition. The energy criterion, as a necessary condition for crack growth, rests on a firm theoretical basis. However, its role as a sufficient condition is less secure. Several alternate criteria have been proposed as necessary and sufficient conditions for the onset of crack growth. We will contrast several of these, including critical strain (Olesiak and Wnuk, 1968; Goodier and Field, 1963) and crack opening displacement ("COD", Burdekin and Stone, 1966) with the energy criterion. We will show that these alternate approaches are inconsistent with the energy criterion, in the sense of being necessary conditions, and so should be rejected as criteria for growth--at least for the elastic-plastic crack.

Jan 1, 1984

By R. Kossowsky, W. C. Johnston

CONSIDERABLE experimental data has been published in recent years on a few directionally solidified aluminum base eutectic alloys. The mechanical properties of A1-Al3Ni eutectic have been studied by Lemkey, Hertzberg, and Ford1',2 and Salkind et a1.3 where the alloy has been demonstrated to behave as a whisker reinforced composite with superior properties over many aluminum alloys. It has also been shown4 that aluminum reinforced with Al3Ni whiskers R. KOSSOWSKY, Member AIME, is Senior Metallurgist, Westing-house Research Laboratories, Pittsburgh, Pa. W. C. JOHNSTON, formerly with Westinghouse Research Laboratories, is Head, Department of Physics, George Mason College, University of Virginia, Fairfax, Va. Manuscript submitted March 28. 1969. IMD__________________ possesses excellent microstructural stability to 508°C. The effect of lamellar structure in A1-CuA12 eutectic was compared3 to the rod-like structure in the A1-Al3Ni eutectic, and was found to be better in low cycle fatigue. This was rationalized3 by postulating that a lamellar reinforcement was more efficient at blocking lateral plastic flow than a rod-like rein-forcement. The purpose of this study is to explore eutectic strengthening in other aluminum base alloys. The Al-Pd system5 forms a eutectic with aluminum and the intermetallic compound A13Pd at 25 wt pct Pd, and has a melting point of 615°C. A13Pd has an orthorhom-bic structure and transforms to hexagonal Pd2A13 at 785°C. Growth characteristics, compression yield strength, creep rupture, and microstructural stability of directionally solidified and as-cast alloys are investigated. Eutectic ingots having a nominal composition of 25 wt pct Pd were prepared by first compacting 1/2 in. diam by a in. high pellets from 99.99+ pct A1 and 99.99 pct Pd powders. The pellets were then levitation cast into 1/4 in. diam by 2 in. long copper molds. Directionally solidified bars were prepared by grinding the cast ingots to 0.195 in. diam, inserting them into alumina

Jan 1, 1970

By Richard H. Olson, Lawrence A. Roe

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% Si02, 31.89% MgO, and 4.75% H20. However, as an industrial commodity, talc rarely approaches theoretical purity. Nevertheless, the impure talc products of commerce find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are tremolite, chlorite, dolomite, mica, and magnesite. Steatite was originally a mineralogical name applied to pure talc. In today's commerce steatite generally refers to the massive variety of talc suitable for electrical insulator manufacture. Block steatite ore can be machined into various shapes. Impure varieties of massive or block talc are still commonly referred to as soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soapstone and talc, this is a natural thing since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as "slip") have been grouped together and called soapstone or talc. Further, there is a mineralogical relationship of pyrophyllite to montmorillonite and talc to hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Indians on Santa Catalina Island, CA. In the mid-1800s, soapstone from deposits along the western foothills of the Sierra Nevada mountains was used by white settlers for building and ornamental stone and in the linings and foundations of furnaces (Anon. 1956). Previous to 1916, the annual recorded production in California did not exceed 2000 tons. In the period 1912 to 1918, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state's annual output of talc was in the range of 9,000 to 20,000 tons. In the mid-1930s, the use of talc in wall tile grew rapidly. In California, the production of talc grew to 63,000 stpy in 1943. The post-war building boom helped California production to grow to 120,000 tons in 1951. In 1968, production was 165,000 tons, 1969 was 145,000 tons, 1970 was 185,000 tons, and 1972 was 155,000 tons. Talc mining in New York state dates to about 1878 when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville, New York. In 1893, this operation was sold to the International Pulp Co. which changed its name to the International Talc Co. in 1944. The company was acquired by R.T. Vanderbilt Co., Inc. in 1974. A new talc operation, the Gouverneur Talc Co. owned by the R.T. Vanderbilt Co., began operations near Balmat, NY, in 1948. The initial capacity of the processing plant was 200 stpd (Gillingham, 1950). Subsequent expansions have increased capacity to over 600 stpd. The Vermont talc industry began just after the start of the 20th century. Talc was discovered in the area of the present Johnson, VT, talc mine in 1902. The American Minerals Co. initiated plant operations at Johnson in 1904. The Magnesia Talc Co. opened a plant at Waterbury, VT, in 1913 (Burmeister, 1963; Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine has a long history as a producer of talc crayons. The Eastern Magnesia Talc Co. was formed in 1924 by a merger of the Eastern Talc, Co.

Jan 1, 1983

By Wayne E. Tuomi

The mining industry is faced with a pressing problem; that is, to develop more efficient methods of extraction, handling and upgrading-techniques that will do the job faster and better than ever before. New techniques require new machines, or applications of new and improved materials that can be used to modify and improve existing machine and equipment designs. The traditional approach has been to increase productivity by increasing equipment size. Prognostication indicates that the trend toward larger equipment sizes and capacities will continue as one answer to the challenge imposed by future increases in mineral demands. But what is the limit on the continued growth of equipment size? Until about 1930, there was a very definite limit-a limit imposed by the strength of the steels and the power plants then available. The equipment engineer had come to an impasse: even though it was easily possible, for instance, to triple the size of a bucket, it had become impractical to correspondingly enlarge the boom, the counterweight, and the power plant.

Jan 3, 1967

By Jerry Tien

Mine regulators are normally used for proper air distribution in underground mines. They are deliberately introduced resistance in the regulated airway, and by altering sizes, they can distribute specific air quantities to regulated splits and free splits (4, 5). The enactment of the Federal Coal Mine Health and Safety Act of 1969, the Federal Mine Safety and Health Amendments Act of 1977, and the regulations adopted by the Mining Enforcement and Safety Administration (now called the Mining Safety and Health ministration) prompted greater discussions of optimal mine regulator locations because of the Act's stringent ventilation requirements (2, 3). For example, by requiring the separation of the air used in the belt haulage entries from the intake and return airways, the regulations required the creation of a third type of airway---the neutral airway, as opposed to the intake and return airways, adding to the complexity of a mine's ventilation network. It is the intent of this report to show that panel regulators should be located in intake airways at the neck of a panel for a blowing fan system and in return airways at the neck of a panel for an exhausting fan system in order to achieve optimal air control. A computer simulation model is used to determine optimal mine regulator location.

Jan 1, 1983

By Nicholas J. Grant, Robert F. Wilde

TAYLOR and Floyd's"" work in establishing phase diagrams based on the elements Ni-Cr-Ti-A1 has led to an understanding of the precipitation hardening mechanism in alloys based on these elements. Nordheim and Grant4 concluded that in simple alloys, and where the aluminum to titanium atomic ratio was such that less than three out of five aluminum atoms were replaced by titanium, the precipitate on aging is the face-centered-cubic Ni 3A 1 phase, called They further found that increasing amounts of hexagonal ? phase, Ni3Ti, precipitated from these alloys when the titanium content exceeded the solid solubility of both matrix and Ni3A1. For alloys of Ni-Cr-Ti-Al, in which the titanium and aluminum contents each ranged from 0 to 4 wt pct, the titanium-rich was superior for strengthening to either pure ?' or 7. It was also noted that the combined titanium plus aluminum content (atomic pct) was a direct measure of the high temperature strength and overaging temperatures for these alloys.4 The present investigation was undertaken to extend existing data on precipitation hardening in the more complex commercial alloys containing higher titanium plus aluminum, and with significant quantities of cobalt, molybdenum, and carbon. Experimental Procedure Reforging of As-Received Bar Stock—The alloys were received as ground, forged bar stock. Chemical analyses and the as-received bar diameters are shown in Table I along with the ASTM grain size after the various treatments. All stock except the Waspaloy was reforged to % in. diam to gain material and to facilitate machining of stress-rupture specimens. Forging was carried out at 2100°F, and discontinued when the bar temperature fell to 1800°F. Heat Treatments—For experixental simplicity it was desirable to heat treat all of the alloys at, the

Jan 1, 1958

By L. L. Wyman

THE resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.1 Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-hered furnaces such as customarily are used for this operation. As might be expected, several other factors exist-such as oil, dirt on the wire, or in the furnace, or metallic surface contacts that might produce reducing gases and be the source of the trouble. However, in consider-ation of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that' the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the result-ant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments com-parable to those previously conducted by the writer,1 which would clarify the effect of the steam on copper, and in copper in the presence of steel.

Jan 1, 1940

By E. J. MCOAUSTLAND

THE behavior of steel after overstrain and at moderate temperatures is fairly well known. It has been made the subject of much investigation, and our knowledge is clear and definite on many points. The ultimate raising of the elastic limit, after moderate overstrain, and the consequent lowering of the ductility, seem to be well established. It is also well understood that the immediate effect of overstrain is to lower the elastic limit, possibly to zero, but that if not interfered with, this limit will subsequently rise higher than before. The "tests after moderate temperature," reported in this paper, were undertaken to verify the above statements for the particular steel under investigation, and also to determine, if possible, the total time required for complete recovery from this state of overstrain. The behavior of overstrained steel at temperatures at or below 32° F. is not so well known. Tests made by Prof E. G. Coker, at McGill University,' show that steel, overstrained and subjected to cold, will remain in a state of overstrain for an indefinite period. I am not aware of any other published results of tests along this particular line. The effect of time and temperature on the recovery of steel from overstrain was made in 1902-3 the subject of sortie investigation in the laboratories of the College of Civil Engineering of Cornell University. A general plan was outlined in connection with the regular courses of instruction in testing of materials; but the press of routine work and the demands of the schedules on the time of the students were so great as to presage long delay in the completion of the work. Not much had been accomplished up to 1904-05, when Messrs. E. C.

May 1, 1906

By J. P. BONARDI, William F. Boericke

BOULDER COUNTY, Colorado, ranked during the war years and until the end of 1918 as one of the foremost tungsten-producing districts of the world. In 1919 production fell off drastically, due to heavy importations of foreign ores from China, Burma and South America. So large were the imports that even after the enactment of a protective tariff in 1922 of 45c. per lb. on tungsten metal, equivalent to $7.14 per unit (201b.) of tungstic acid? (WO,), the stocks of metal in this country were extensive enough to supply the demands of industry, and prevent general resumption of mining by domestic producers. Even today there are only two producers in the Boulder district though at one time as many as twenty separate companies were in operation. About the same ratio holds for other tungsten-producing districts in the country, including California and Nevada. Total consumption of tungsten concentrate in terms of 60 per cent WO2 in the United States amounted to approximately 3790 tons in 1928, according to Frank L. Hess.' Of this amount, domestic mines contributed 1290 tons, and the rest, 2500 tons, was imported. Yet in 1917, with tungsten concentrate selling at $20 per unit, the Boulder district alone produced 2707 tons, indicating the effect of enhanced ore price upon production. It is believed by American tungsten miners that, given a sufficiently high tariff, all the demands of industry can be met by domestic production without placing a prohibitive burden on consumers. For instance, in steel manufacturing the percentage of tungsten entering into the manufacture is so small that, ?regardless of cost, it can constitute but a small fraction of the cost of steel to the buyer.

Jan 1, 1929

By Samuel S. Wyer

THE following abbreviations have been used in, the text: Cassier's, Cassier's Magazine. Eng. Lond., The Engineer (London). Eng. Mag., Engineering Magazine. Eng. and Min. Jour., Engineering and Mining Journal. Eng. News, Engineering News. Eng. Rec., Engineering Record. Engng., Engineering. Engr., The Engineer (Chicago). J. I. and S. I., Journal of the Iron and Steel Institute. Jour. F. I., Journal of the Franklin Institute. Jour. Assn. Eng. Soc., Journal of the Association of Engineering Societies. Mar. Eng., Marine Engineering. . Mem, Soc. Ing. Civ., France, Memoires de la Society des Ingenieurs Civils, France. Prac. Eng., Practical Engineer. Proc. Digs. Soc. of W. Pa., Proceedings of the Engineers' Society of Western Pennsylvania. Proc. I. C. E., Proceedings of the Institute of Civil Engineers. Proc. I. 1M. E., Proceedings Institution of Mechanical Engineers. Trans. A. I. M. E., Transactions of the American Institute Mining Engineers. Sci. Am., Scientific American. Sci. Am. Sup., Scientific American Supplement. Zcitschr. d. V. D. Ing., Zeitschrift des Vereines Dentscher Ingcnieure.

Mar 1, 1905

Sailing westward from the Society Islands in the fall of 1774, England's noted explorer Captain James Cook discovered New Caledonia-that long, linear island that has played such an important and varied role in the history of nickel. Upon his return to England the following year, Cook's announcement of this uncharted island generated governmental interest, but its distance from the Island Empire, the troubles in the colonies, and the difficulties with France combined to keep English interest indirect and in the background of the then-current events.

Jan 10, 1968

By D. S. Gleason, D. E. Severson, D. R. Skidmore

Pittsburg and Midway Coal Co. has modified the German Pott-Broche process, on which patents date back to 1927, to produce on a bench scale liquid products by solution hydrogenation of coal. A continuing program of lignite solution-hydro gena-tion experiments is directed toward investigating coal solution reactions, determining favorable conditions for the solution refining of lignite by the Pott-Broche process, and investigating some of the uses for the de-ashed product obtained from lignite The German Pott-Broche process1" on which patents date back to 1927, has been modified by the Pittsburg and Midway Coal Co., a Gulf Oil subsidiary, to produce on a bench scale liquid products by solution -hydrogena-tion of coal." The objectives of the present effort are to investigate coal solution reactions, to determine favorable conditions for the solution refining of lignite by the Pott-Broche process, and to investigate some of the uses for the de-ashed product obtained from lignite. This paper is a summary of results to date in a continuing program of lignite solution-hydrogenation experiments. The coal solution reaction program has several principal aims. The first of these is to determine whether lignite can be successfully dissolved in solvents that might be practical for commercial development. The second object is to determine whether the solvents function after successive cycles of use, recovery, and reuse. It seems necessary to the economics of a potential commercial process that the solvent be recycled. Third, it is desired to learn something about the distribution of the ash constituents between cake and filtrate. The extent of ash removal is important. The nature and quantity of mineral matter passing through the filter may determine end-use marketability. For certain use applications, trace quantities of certain minerals can be objectionable, e.g., titanium and vanadium must be very low in electrode carbon for aluminum production. The Solution Reaction The coal solution Process involves an extremely complex system of chemical reactions. An initial solvent such as anthracene oil is a mixture of hundreds of different compounds with a boiling range of roughly 500" to 750°F at atmospheric pressure. The coal macro-molecule is broken down by thermal decomposition and solvent action into myriads of different compounds, some the same as those comprising the solvent. This similarity in structures opens up the possibility of production and subsequent recovery of solvent. Some solvent is inevitably lost by reaction. Regeneration of solvent was not a problem in the early German Pott-Broche plant. The coal refinery was an integral part of a petroleum refinery complex and replacement solvent was readily available. A coal refinery using lignite, however, might be isolated from other hydrocarbon processing facilities and the regenerability of solvent could be vital to the economic success of the venture. Several structural features of the solvent molecules have been cited as important to the coal solution process.'. The first of these is aromaticity of the material, the second, ability to transfer hydrogen to another molecule, as for example the ability of tetralin to transfer hydrogen and be converted to naphthalene. Finally, the presence of hydroxyl groups on aromatic rings within the molecule, i.e., phenolic character, seems beneficial. Mixtures of pure compounds have been tried by various investigators. Mixtures of o-cresol, a phenolic substance, and tetralin were found to dissolve bituminous coal better than either substance alone.3 This maximum solubility was not found with lignite." Hydrogen contributes to the reaction by hydro-genolysis and by combining with free radicals and molecular "loose ends" to stabilize the compounds formed in coal depolymerization. High boiling point, and correspondingly high molecular weight, seems to be a property which improves solution potential for coal with a given type of compound.' The maceral components of the coal appear to have an important bearing on its ease of solution. The fusain portion is quite inert to solvent action, but the an-thraxylon material dissolves quite readily.3 The hydrogenation reaction can be improved by the use of a catalyst; commercial hydrogenation catalysts having been found effective. Although cost is involved in the use of catalyst and catalyst recovery, the resulting saving in time and perhaps lowered temperature or pressure might justify their use in the solution refining process and decrease the total process costs. Apparatus and Procedure The coal solution runs were made in a 1-gal stainless steel stirred autoclave. The autoclave was provided with thermocouple wells and a transducer to permit continuous recording of temperature and pressure. The autoclave stirrer was magnetically driven, eliminating the leakage inherent with a rotating pressure seal. For runs in which a catalyst was used, the catalyst in the form of beads was placed in a wire mesh container mounted on the stirrer shaft. A control system programmed the heatup and reaction cycle. The permissible heating rate was 5°F per min because of the need to minimize thermal stress in the autoclave body. The temperature was raised at that rate until the reaction temperature was attained and then the temperature was held constant for the desired length of time. The maximum temperature seldom exceeded the average run temperature by more than 15°F.

Jan 1, 1971

By Lucius W. Mayer

The iron-mines of the Ilsede Hütte Co. are at a town called Peine, about 20 miles east of the city of Hanover, on the railroad to Brunswick (Braunschweig). Hanover, the capital of the province, is a military city, of approximately 250,000 inhabitants, and Brunswick, 33 miles to the westward, has half this number. The mines here described are located in a hamlet called Bülten. The Ilsede Hütte Co. operates two mines, 1.5 miles apart, in this district, Gruber Bülten Adenstadt and Gruber Lengede Bodenstadt. It also operates an iron-mine north of Hanover, known as Eiserhaven, and one in the Harz mountains, the Georg Friedrich, at Grauhof. At Bülten a coarse conglomerate, a, Figs. 1 and 2, contains nodules of limonite, cemented together by calcium phosphate. The ore contains Fe, 25 to 45; Mn, 3 to 4; P, 0.6 to 1.4; S, 0.02 to 0.09; and CaCO3, 40 per cent. Directly above the conglomerate is limestone, b, followed by a mixture of clay and sand, c. Below the conglomerate is a hard clay floor, d. The ore-body, from 10 to, 12 km. long, and from 3 to 4 km. wide, has a maximum thickness of 20 m. It clips approximately 10° S.E., and strikes N. 45° E. Diamond-drill prospecting shows that the thickness diminishes to 1 m. as the end of the deposit is approached to the northward. At this point the deposit is 250 m. below the surface. In Fig. 2, the arrow, A, indicates the general direction of the work along the face, a, which is carried forward in a straight line for its entire length. At B, a train is approaching, which has come from the bench-track, shown at G, by a circuitous route, and is dumping the overburden behind the face, in the space left by the excavated rock. Formerly the work at this mine was essentially open-cut, the deposit having a very strong outcrop. Figs. 1 and 2 show also

Sep 1, 1908

By L. R., McLeod

NO important changes in metallurgical practice are exhibited in the smelter that has been erected for treating the Morenci concentrate: the material is charged to reverberatory furnaces without roasting, and the matte subsequently blown in Peirce-Smith converters to separate the iron and sulphur from the copper. In fact the process is essentially the same, except for preliminary roasting of the concentrate, that was adopted in the new smelter that was built for the Arizona Copper Co. at Clifton, a few miles away, to treat Morenci concentrate just before the start of the first World War, and which went into service in October, 1913.

Jan 1, 1942

By Frank R. Milliken, Robert Goodwin

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943