Search Documents

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By George Fancher, R. L. Whitting

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By R. L. Whitting, George Fancher

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

CONTENTS [The Nature of Strain Markings in Alpha Brass (paper by J. E. BURKE and C. S. BARRETT, Met. Tech. Feb. 1948. TP 2327). ......................... 2 X Ray Studies of Twinning and Untwinning in Magnesium Alloys (paper by J. B. HESS and R. L. DIETRICH, Met. Tech. Feb. 1948. TP 2328) ................ 11 ]

Jan 1, 1948

By C. W. Dunham

DESIGN of the structures for the Morenci Reduction Works involved many interesting problems. Naturally, the chief purpose of these structures is to house and support the equipment and other things necessary for or incidental to the conduct of production. hence most of the features of the design were developed to suit these particular conditions; however, several are so generally applicable as to warrant description.

Jan 1, 1942

ALABAMA Aldrich -Thomas, D A Altoona -Cain, J Anniston -Cowie, L K Walmsley, W N White, H E Ashland -Sturdevant, J C Bankhead -Connaway, M B Bessemer-Ball, E M McKenzie, W C, Jr Mitchell, F R Morgan, C Thompson, N E Birmingham -Abbott, C E Adams, J H

Jan 1, 1923

By C. E. Birchenall, F. N. Rhines, L. A. Hughes

A. J. Shaler—I should like to congratulate the authors on the presentation of this paper, which we have been awaiting a long time. The view they have taken of the sintering process, namely that voids are comparable to particles of a second phase capable of dissolving to a slight extent in the metal phase, is an interesting but dangerous one. Pines has given a first-order solution of the problem and Has predicted a decrease in the concentration of pores near the surface. The authors of the present paper have experimentally demonstrated the second-order effects, that is, the diffusion of the space phase between voids of different sizes, and also the movement of atoms from highly curved parts of a void to less curved regions of the same void. I have recently calculated the rate of vapor-phase transport within odd-shaped pores in copper at 850 °C and found that probably at that temperature volume flow is the more rapid shape-changing mechanism. The authors of the present paper have found that at 1000°C, vapor-phase transport is dominant. There is no disagreement here, I think. The dominant phenomenon can easily be different' in different temperature ranges and with different pore shapes: I used a cylinder going to a sphere, not a tricuspid going to a "triple cuspidor." But there is some danger in the other art of the explanation, that is, in the study of the diffusion of vacancies from a pore to its neighbors and to the outside. A vacancy is very different in dimension from an atom. When it moves, it carries a field of elastic strain. This has to be taken into account. A concentration gradient of vacancies can cause them to diffuse. But in the absence of such a gradient, they can be made to diffuse by a field of stress. What happens in some of our experiments, and it is most noticeable in the shrinkage of synthetic cylindrical pores, like the tubes we have been working with, may be broken down into the following steps. (1) The presence of a surface establishes a vacancy concentration gradient, as Dr. Kuczynski and the present authors have shown. (2) Vacancies then diffuse in order to decrease this gradient. (3) In so doing, they cause an elastic field to be built up in such a direction as to oppose the diffusion, so that it slows down until it reaches a steady-state rate. (4) The steady-state flow is due to the fact that the surface tension acting on curved surfaces applies a stress to the system which itself mechanically causes vacancy diffusion. What I have said is that the diffusive types of flow of the authors and of Dr. Kuczynski are transient phenomena which soon stop if the pores are large. We are then left with a mechanical problem only, and our researches have not yet disclosed just what the mechanism of flow is; it may be a slip process, or it may take place by a vacancy diffusion of the type Nabarro has de-

Jan 1, 1951

By A. M. Gaudin

THE so-called Kick law' is generally accepted to . mean that for each reduction to one-half in particle diameter, in a unit weight, the same amount of work is required. In crushing-efficiency calculations on crushing tests it is customary, when basing the calculation on Kick's law, to assign ordinal numbers to each standard sieve size. These ordinal numbers increase by a constant difference with each successive sieve aperture, because standard sieve apertures are in constant ratio. Minus 200-mesh is generally assumed as equivalent to 37 microns in size. By definition, the ordinal number multiplied by the per cent material of any size is equal to the energy units in the material of that size in a unit weight of sample. The sum of all energy units is the energy units content of a unit weight of sample, whether it be crusher feed or product. The difference between the energy units in the product and that in the feed is the tangible result of the work input per unit weight of feed. From this the amount of work necessary for one energy unit may be calculated. This has been done for a quartz crushing-test made at the Intermountain Experiment Station of the U. S. Bureau of Mines at Salt Lake City, in which the net work going to crushing was carefully measured. The results of this crushing test are given in Table 1.'

Jan 1, 1929

A SPRING meeting is to be held at Cleveland this month under the joint auspices of the Iron and Steel Committee and the Ohio Section with the cooperation of the neighboring sections in Pennsyl-vania, Illinois, and the other States of the Great Lakes region. The discussions will be focused on just one subject, that of manganese, but will cover that thor- oughly as is indicated by the following list of papers. TECHNICAL PROGRAM Some Political Aspects of the World Manganese Situa-tion. By C. K. Leith, Professor of Geology, Uni-versity of Wisconsin, Madison, Wis. Manganese Resources in Relation to Domestic Con-sumption. By J. V. W. Reynders, Consulting En-gineer, New York, N. Y. Manganese Deposits of the' Gold Coast, Africa. By Sir Arthur E. Kitson, Director of the Geological Sur-vey of the Gold Coast, London; with Notes on the Petrology of Certain Associated Manganese Silicate-bearing Rocks. By Maj. N. R. Junner. Reserves of Lake Superior Manganiferous Iron Ores. By Carl Zapffe, Manager, iron ore properties, North-ern Pacific Railway Co., Brainerd, Minn. Iron Manganese Alloys Low in Carbon. By. Sir Robert Hadfield, Hadfields, Ltd., London. Manganese in Non-ferrous Alloys. By M. G. Corson, Consulting Engineer, New York, N. Y. Importance of Manganese in the Steel Industry. By H. M. Boylston, Professor of Metallurgy, Case School of Applied Science, Cleveland, Ohio. Minnesota Manganiferous Iron Ore in Relation to the Iron and Steel Industry. By T. L. Joseph, E. P. Barnett and C. E. Wood of the North Central Min-ing, Experiment Station, U. S. Bureau of Mines, Minneapolis, Minn. Representatives of the leading steel companies, the Army, the Navy, the Geological Survey, Bureau of Mines, and leading technical societies will be present and a lively discussion of the various papers is already assured. Nearly 14 pounds of manganese is needed for every ton of steel made. Estimates indicate that the total reserves of ore in this country suitable for making ferro would hardly supply domestic requirements for ten years, even if it could all be mined in that time. The grade of ore called for by present practice must come from abroad. The present tariff policy of this country is stated to cost industry $8,000,000 in order to force production of manganese ore to the extent of $600,000. What is the wise thing to do? Should a stock be accumulated? If so, how? Is it feasible to change practice and use low-grade ore or to beneficiate the ores of this grade and meet our requirements? What progress is being made in this direction? ,These and similar questions are raised in the various papers that have been submitted and will be open for dis-cussion.

Jan 3, 1927

By H. J. Wogner

STORAGE of natural gas in underground reservoirs is one of the most important developments in the natural gas industry in recent years. However, it is only when we consider this development together with proved fuel reserves, the know-how of the fuel technologist, and the possibility of making manufactured gas available over large areas, that we begin to appreciate fully the impact that underground storage of gas may have on the future growth and development of large areas in the United States. During the past winter, shortages of natural gas in the industrial East were given wide publicity and domestic consumers were requested to reduce their requirements to a minimum, so that war plants might have sufficient gas to continue operations. Curtailments would have been more drastic except for the fact that large volumes of natural gas had previously been stored in underground reservoirs. Storage of natural gas in depleted or partly depleted gas or oil sands is not new, having originally been tried, as far as I know, about 1915. About five or ten years later an attempt was made to store manufactured gas in a depleted gas sand. This proved unsuccessful at first because the gas was not properly cleaned and the impurities plugged the pores in the sand.

Jan 1, 1945

By R. G. Green, R. L. Dowdell

LEAD POISONING as a result of eating lead pellets deposited in marsh areas is a cause of high mortality among ducks, geese, and other waterfowl ingested lead shot become trapped in the gizzard with gravel and are slowly ground away by the grit. Absorption of lead as it passes through the intestine in a finely divided state produces severe lead poisoning which is usually fatal. Ducks and geese with lead poisoning develop first a typical green diarrhea. Later, paralysis of the wing muscles prevents flight. As the poisoning continues with further grinding of the shot trapped in the gizzard, increasing paralysis reduces the bird to helpless-

Jan 1, 1937

By James E. York

THE honor so fairly earned and so incompletely and tardily paid to Henry Cort, the inventor of the puddling-furnace and the, rolling-mill, has been fully set forth by Mr. Charles H. Morgan,1 and needs no further emphasis here. In view of the importance of the rolling-mill in the treatment of iron and steel, the paucity of information concerning it is surprising. With the exception of a hook, written about 35 years ago, by Peter Bitter von Tunner, an Honorary Member of this Institute, and of desultory articles on simple sections, which have appeared in technical journals, I know of no pub¬lication attempting to treat this subject, although volumes have been written on the scientific theory and technical manipulations involved in other branches of the iron- and steel-industry. This strange anomaly may be due to the fact that roll-turning cannot be called a scientific business. It does not ordinarily come within the range of an educated engineer; yet it cannot be performed by an ordinary mechanic. It demands some of the qualifications of an engineer, in designing, and those of a mechanic, in execution. The men who have followed this trade have controlled the training of their successors. In many cases the technical knowledge required bas been handed down from father to son, and there has been a motive of private interest to prevent its public dissemination. Moreover, the statement of the various principles involved in the process would require, besides manual experience, a degree of scientific knowledge which roll-turners do not usually possess; and, finally, any book on the subject, in order to possess real, practical value, would have to be so fully illustrated as to make it very costly to publish. Regarding my own experience, I may say that I served a six-

May 1, 1906

By M. H. HARRINOTON

THE Transactions of the Institute afford abundant evidence of the general recognition by mining engineers of the importance of a safety-lamp which will not only give warning of the presence of fire-damp, but will also indicate the proportion in which it is present.' Mining-men are only too familiar with the frequent and sudden changes that constantly occur at the working-face of a gaseous mine. Nothing illustrates more forcibly the pregnant condition of the strata enfolding the seam and the seam itself, than the fact that a circulation of perhaps 150,000 cu. ft. of air may contain 2 or even 3 per cent. of marsh-gas, representing a volume of from 3,000 to 4,000 cu. ft. of this gas pouring-out each minute from the natural strata into the mine-workings. It would, indeed, be strange if this great outflow of gas were always constant, and it creates no surprise that such earth-breathings, as they may be called, are spasmodic and irregular in their wane and flow. There are other causes that act to vary the gaseous condition of mine-air. Gas has a tendency, often very manifest in mine-workings and airways, to stratify and, at times, to travel long distances in veins or streams. It is common to catch and lose the gas in the lamp when making a test. At times two lamps, held side by side in an air current, will indicate different gaseous conditions of the passing air. When testing for gas, the lamp may suddenly fill with flame, in a mine-chamber, where a moment before a careful test showed the presence of but 1 per cent. of gas. It is sometimes remarked that there is little need of detecting a smaller percentage of gas than is revealed by the common

Jan 1, 1906

By R. G. Hudson, L. Yang

In electrochemical separation of metals, it is necessary to control the potential applied between the electrodes so that only the desired electrode reactions can occur. A knowledge of the minimum potential needed for a given electrode reaction to take place continuously is therefore pertinent to the success of the process. In molten chloride systems at high temperatures, activation polarization is believed to be small,1,2 so the minimum potential needed for the electrolytic decomposition of a molten metal chloride MC1n (n = valence of the metal ion) is therefore essentially the equilibrium electrode potential E of the metal-chlorine galvanic cell in the solution. If the decomposition products are pure M and chlorine at a pressure of p atm, E*Eo-rt/nf in [i] Since EO (the standard electrode potential of MCln) is a constant at a given temperature and R (the gas constant), and F (the Faraday's constant) are all constants, the variation of E with the electrolytic bath conditions is largely determined by the effect of the latter on the activity of the metal chloride amcln (standard state = pure MC1,). Measurement of E and study of how amCin varies with temperature and concentration, the nature of the solvent, and that of the coexisting solutes are therefore pertinent in the selection of optimum operating conditions for the electrochemical separation of metals. Because of its low melting point, high decomposition potentials of its components, and the low solubility of heavier metals in it, the LiC1-KC1 eutectic melt is a useful solvent and has been used in the electrodeposition of Mo,3Ce,4 and u5 metals. Senderoff and Brenner3 measured the potentials of Zn/Zn++, Fe/Fe++, Cu/Cu+, Mo/Mo+++, and Ag/Ag+ against an Ag/AgCl (pure) reference electrode at 600°C and a concentration of 4.1 mole pct of each chloride and came to the conclusion that complex ion formation occurred in some of the melts. Laitinen and LiUe gave an electromotive force series at 450°C for a number of {Metal/Metal ions (unit activity)) electrodes in LiC1-KC1 eutectic melt, the {pt/pt++ (unit activity)) electrode being chosen as the reference. Walker and Danly7 studied the ther-modynamic properties of NiC12 in LiC1-KC1 eutectic melt over a wide range of temperatures and concentrations by measuring the electrode potential between a nickel electrode and a chlorine electrode in the melt. Since potential measurements made by using the chlorine reference electrode are of more direct significance both in the study of electrochemical separation and in the evaluation of the thermodynamic properties of the melt, it is therefore decided to measure the electrode potentials of cells of the type {M/MCin (mole fraction = N) in LiC1-KC1 eutectic melt/Cl2 over a range of N values and temperature for a number of metal chlorides. The results should indicate the order by which the various metals plate out on the cathode and how this order is affected by temperature and the concentration of the metal chloride in the solu-

Jan 1, 1960

By William B. Plank

AGAIN the records show an unprecedented enrollment of students in the mineral technology schools of the United States and Canada. In the current year, 1938-'39, 9619 students were resident in the 53 schools of the United States arid 1014 in the six schools of Canada. These data are from my fifth study of the mineral technology schools of the United States and Canada. the last previous study having been made for the year 1936-'37. The undertaking as previously was made under the auspices of the Mineral Industry Education Division of the A. I. M. E. The data or, the various schools were collected in the same way as for former studies.

Jan 1, 1939

By J. W. Dougherty

THE Hollinger gold mine is in the Porcupine mining division, District of Cochrane, in the northern part of the Province of Ontario. The adjacent town of Timmins, with a population of 25,119, lies 490 miles by railway north of the city of Toronto. GEOLOGY The property is situated on the northwest limb of a major syncline, which pitches northeast at approximately 50°. The principal rocks of the Hollinger area are of pre-Cambrian age and consist of altered, schistose, Keewatin lava flows intruded by stocks of schistose, quartz-feldspar porphyry generally assigned to the Algoman period. The structure of the Keewatin series is extremely complex as a result of close folding and some faulting. The schistosity, trending north 70° east and dipping steeply to the southeast, is most highly developed along a subsidiary anticline in which the major porphyry bodies occur. The ore bodies, which exhibit three principal structures, consist of quartz veins and associated pyritized wall rock. Some lodes are com-posed of en echelon veins, others exhibit a main quartz body with branch-ing stringers and a third consists of a single definite lead. Gold, in a coarse visible form, may be confined to quartz in some ore bodies but in others it is finely divided and is found not only in quartz but also asso-ciated with pyrite in the adjacent wall rock. In many veins the dis-tribution of gold is such that there are several ore sections, separated by areas of low-grade material, in the same vein although its physical appearance remains unchanged.

Jan 1, 1940

By William B. Plank

IN this paper are presented the results of a complete statistical survey of the enrolment, courses and degrees, and the employment situation of recent graduates in all of the 46 institutions in the United States, including Alaska, and four of the six schools in Canada that grant degrees in mineral technology. The data were collected by the writer by means of a questionnaire in December, 1933, to which all the institutions, except one, replied. Included also are data of a similar study made by the writer in May, 1933, for the S. P. E. E. summer session of mining and metallurgical teachers at the University of Wisconsin and published in the Journal of Engineering Education for December. 1933. Some of the data of a paper of the writer's entitled, "The Trend of Mineral Engineering Student Enrolment in the United States," read at the A. I. M. E. meeting on Feb. 16. 1931, are given for comparison. Acknowledgment is made to all the administrative officers of the institutions who took the time from their busy lives to supply the in- formation asked for. Their fine cooperation has alone made possible these two surveys with a completeness of detail never before attempted

Jan 1, 1934

By A. P., Svenningsen

ECONOMICAL handling of a minimum of 25,000 tons of minus 3/4-in. ore per day, grinding it to 2 per cent on 65 mesh, and effecting a high recovery of the copper at the lowest possible cost were the principal aims in the design of the new Morenci concentrating plant. Dealing with a tonnage of this magnitude, it is obvious that lost motion cannot be tolerated. When ore is carried on a conveyor an unnecessarily long distance or elevated to a greater height than necessary, or when pulp flows in a launder by a circuitous route thereby losing elevation and distance, we have lost motion which is always costly both from the standpoint of construction and operation. In addition to the 25,000 tons of ore which must be handled, 100,000 tons of water per day has to be carried through the plant in the treatment of the ore. Though water is not so difficult to handle as the ore, the combined tonnage represents a figure which could easily run into a considerable monetary loss per day if all phases of the design were not carefully followed with the idea of eliminating any unnessary handing of materials.

Jan 1, 1942

By AIME AIME

ON the headwaters of the Hudson Riser, in a sparsely populated area of the north woods at Tahawus, N. Y., thirty miles from the nearest railroad, is the Maclntyre property of National Lead Co. Operations involve the mining and processing of titaniferous iron ore to produce ilmenite concentrate, and magnetite concentrate containing vanadium, for use in the production of iron, titanium, and vanadium in the war program. Accordingly, Maclntyre at present is classed as a war plant. More than 3000 long tons of ore is ruined daily by opencut methods and treated in an ore concentrating plant.

Jan 1, 1943

By H. M. Chance

Discussion of the paper of H. M. Chance, Bi-Monthly Bulletin, No. 23, September, 190S, pp. 791-808. CHARLES CATLETT, Staunton,Va. (communication to the Secretary *):-Mr. Chance's suggestions that the brown hematite ores of the Potsdam formation are due to the alteration in place of iron sulphide, and that their extension may reasonably be expected to contain valuable deposits of unaltered sulphide, are interesting; but the facts marshaled by him are too limited to justify more than the hope that they may serve as a commercial source of sulphur. It is true that these deposits have been the source of large amounts of iron-ore; and it. is common, as stated by him, for the mining operations to extend to a shallow depth only; but this is largely due to the fact that the surface-material represents an accumulation from the breaking down and collection of the ore which formerly reached a much higher level. With, increasing depth comes a decreasing thickness of valuable material. This is especially appreciated by a glance at Mr. Chance's drawings. This is the reason why so many disappointments have resulted when these ores have been followed to greater depths. Even if the ore is largely derived from oxidation in place, it is impossible to ignore the great number of concretionary forms, as well as those showing the evidence of secondary solution and deposition now taking place, such, for instance, as the part replacements of fragments of quartzite derived from the underlying beds. Concretionary form does not necessarily mean long transportation, and may be a variation of material in place; but commonly it is an evidence of collection, and tends to imply that more or less concentration has taken place. This fact would also argue against an equally extensive develop¬-

Nov 1, 1908