Search Documents

By Oscar Weiss

An aerial magnetometer survey was carried out by the author's geophysical organization over the Vredefort dome, where Witwatersrand beds are wrapped around a granite plug 25 to 30 miles in diameter. The well- known magnetic shales of the Lower Witwatersrand system (to be referred to as LWW) give strong negative anomalies over the out-cropping portion of the dome. This is unusual as these same shales -cause positive anomalies over large areas near Johannesburg and along a strike of 130 miles between the East Rand and Klerksdorp. It is suggested that the negative polarization is caused by heat and stresses connected with the doming. This negative polarization of sedimentary beds, which usually cause positive anomalies, is a good example of how "magnetic lows" can be caused by "structural highs." Significant magnetic anomalies should be tested by gravity and seismic methods irrespective of the sign of the anomalies.

Jan 1, 1949

Jan 1, 1881

By K. R. Bixby

OPENING of numerous stripping operations in Ohio, Pennsylvania, and other districts, particularly outside the Middle West and Southwest where the large-scale stripping mines predominate, holds the limelight for the year 1940. Several factors are responsible for this expansion. One is the scarcity of untested and undeveloped properties in this central field. Another has been the development of earth-moving and preparation equipment suitable for these smaller tonnage tracts. Draglines of the Walker type, small long-range .hovels, and large-capacity tractor- drawn scrapers have to be considered. Wash boxes, designed for light tonnages, costing a few thousand dollars, have made their contribution.

Jan 1, 1941

By R. Kossowsky

BRIDGMAN has listed five possible transitions in bismuth at 25°C which were observed as volume changes. He was unable however to detect the last three transitions by electrical-resistivity changes. Kennedy and LaMori have verified the pressures at the Bi 1-11 and Bi 11-111 transitions. They suggested however that the 125-kbar transition previously reported by Bundy3 actually corresponds to the 90,000 kg per sq cm transition observed by Bridgman.1 Jura4 reported a well-defined drop in resistivity at 92 kbar obtained by a four-lead method. The Bi 111-IV and Bi IV-V transitions have not been reported in any of the above-mentioned references.'-' Bundy3 observed a small dent in the low-temperature boundary of the Bi Vll region which is consistent with the presence of a 111-IV boundary. Zeitlin and Bray-man5 were the only ones to report small but well-defined drops in resistance of bismuth at 44.0 and 63.8 kbar, corresponding to Bridgman's 111-IV and IV-V transitions, respectively. High-purity (99.99 pct) 0.020-in.-diam 0.5-in.-long bismuth wire was used to calibrate the Uniram tetra-hedral high-pressure apparatus used in the present work. The bismuth phase changes at 25°C were correlated with changes in electrical resistance as a function of pressure. The output of a sensitive bridge constructed of carbon resistors and kept at a constant temperature of ±°C during the measurements was fed to the Y axis of a MoseleyX-Y recorder and the X axis was used for time scans. Specimens were pressurized using a hydraulic press with maximum capacity of 200,000 lb. Load was applied in increments of 2000 lb and held for about 3 min. The resistance was recorded at the end of this time period. Good contact was established below 20,000 lb. Typical recorder charts are reproduced in Figs. 1 and 2 which show that resistance fluctuations were practically nil during each time scan. Well-defined discontinuities in resistance were observed at 58,000 and 82,000 lb, Fig. 1. Two small but definite "blips" are noticed at 92,000 and 122,000 lb, Fig. 2. At 156,000 lb another drop is observed which

Jan 1, 1967

By D. B. RUSHJIORE

(New York -Meeting, February, 1912.) TORCHES were used by the early Romans for mine-lighting, and these were followed by open lamps or earthen jars filled with tallow or oil, and later by candles. In early coal-mining, explosive gases seldom occurred, and, if they were encountered, the danger of explosion was materially diminished by the absence of any ventilating-system and the consequent insufficient circulation of air to form with the methane an explosive mixture. As the art advanced, the danger of fire-damp became more apparent, and methods for testing the air were resorted to as early as in the fifteenth century. The method of testing consisted in lowering a clog in a, basket down the shaft. As soon as he encountered fire-damp he would commence to howl, after which he was withdrawn, and a leafy bush was fastened to the end of the rope and run rapidly up and clown the shaft. This so disturbed the accumulation of gas as to cause it to rise out of the shaft. Later this odd method of testing was improved upon through the discovery that a light inserted in a body of fire-dam p would produce a blue flame. Candles were used for this purpose, and, when fire-damp was thus discovered, brushing or some other primitive method of fanning was resorted to for driving out the gas. In some instances the gas was burned away, regardless of the danger thereby incurred. A man, wearing a well-moistened coat and a mask with glass spectacles, descended in the mine a few hours before each shift. With a long stick, to which was fastened a burning torch or candle, lie would crawl on the floor with the stick so raised that the light would sweep the roof and ignite the gas which it encountered. In this position the flame of the explosion would pass over him, after which he would retreat from the gases resulting from the combustion. The occurrence of serious accidents resulted in

Jul 1, 1912

By Junichi Sato, Takash Suzuki, Tatsuo Imamura, Mamoru Hojo

INTRODUCTION Hitachi Refinery of Nippon Mining Co., Ltd. was constructed in 1911. The refinery began early to recover by-product metals and to manufacture copper products. Today, the refinery recovers gold, silver, selenium, platinum and palladium as by-products of the copper refining process and manufactures copper powder, copper foil, wire bars and chemicals for plating. In 1969, the capacity of the Hitachi Refinery reached 6,000 tons/month. (T/M). Because, at that time, the forecast was for the demand for copper in Japan to increase, planning for the expansion of the Hitachi and Saganoseki refineries was begun. A new 10,000 T/M capacity tank house, a new electrolyte purification plant and a enlarged anode slime treatment plant were planned for the Hitachi Refinery. Construction at the Hitachi Refinery began in December, 1970, and was completed in April, 1974. The development of new machines and processes has resulted in an efficient refinery with a production capacity of 16,000 TIM. This paper is a report on the new anode slime treatment plant at the Hitachi Refinery, and especially on the copper removal process in that plant, the Ferric Leaching Process.

Jan 1, 1976

By E. M. Wise

THOUGH known as the platinum-group metal- the sextuplet, platinum, palladium, iridium. rhodium, osmium, ruthenium, might well be called the American metals or perhaps Pan-American metals, as the ore containing them eras first discovered in South America, and in recent years the largest production has come from North America. The South American alluvial deposits, which also, contain gold, are in active production, as are the alluvial platinum deposits of Alaska, but the main production is from the copper-nickel ores of Sudbury, Ontario. The Russian deposits in the Urals were the source of most of the worlds platinum for about 100 years, but since 1934 have assumed second place. For a time considerable amounts of platinum came from several rather rich deposits in South Africa but these were exhausted quickly. However, a tremendous reserve of lower-grade ore exists there, which could be worked profitably if the price of platinum were considerably higher.

Jan 1, 1942

By S. F. Reiter, You-Chao Liu, W. R. Hibbard

Cyril Stanley Smith in his classic 1948 Institute of Metals Lecture&apos; noted in the case of annealing twins that: "It is well known that approximately the same number of twins per grain and the same general geometry are maintained in large grains as in small ones, a fact that certainly suggests a mechanism such as the above where boundaries and twins grow proportionately together. If this view is correct, a spherical grain should have no mechanism for keeping its twins." Such a constancy of twins per grain would be of particular interest as a tool for the study of the origin of annealing twins. It has been proposed by Mathewson2 and later by Barrett3 that in face-centered cubic metals slip occurs in the {111} Plane by <112> shears which combine in pairs to produce the macroscopically observed <110> movement. This proposal is schematically inviting since <112> slip permits the atoms of one plane to move along the interatomic valleys of its neighbor rather than up the hills across the atom sites. There is strong experimental evidence? that annealing twins result from the growth of nuclei in the form of "twin faults" produced by single <112> shears. It is possible that more twin faults would form at low deformation temperatures than at high ones, because the more rigid lattice may increase the tendency to "freeze" the twin faults and prevent their dissipation in slip. This is suggested by (1) the greater resistance to slip at low temperatures and (2) greater tendency toward mechanical type twinning at low temperatures (a summary of these factors is presented by Seigle and Brick5). These considerations would suggest the following: a. Constant twin/grain ratio for specimens deformed constant amounts at a constant temperature, but annealed at various temperatures above the recrystalliza-tion temperature. b. Larger twin/grain ratios for re-crystallized specimens previously deformed constant amounts at lower temperatures. The purpose of this investigation is to test these considerations. One half in. rods of phosphorous deoxidized electrolytic copper and 70-30 alpha brass (68.36 pct Cu, 0.005 pct Pb, 0.01 pct Fe, 31.62 pct Zn remainder) were rolled to a thickness of 0.350 in., milled to specimens 0.350 X 0.437 X 2 in., and annealed at 700°C to an average grain size of 0.065 and 0.090 mm, respectively. These specimens of each metal were then rolled 50 pct reduction in thickness and annealed one hour under conditions which were all combinations of the following: Rolling Annealing Temperatures. Temperatures. °C °C -70 400 25 500 200 600 Standard metallographic techniques&apos; were used to prepare specimens. By the method of lineal analysis7 using a minimum of ten samples of fifty grains each for each specimen, the ratios of twins* per total grains, twins per twinned grain, twin families* per total grains and twins per twin family were determined. Recrystallized grain size was determined by A.S.T.M. comparison methods.8 All observations were made on the rolling plane. The results are tabulated in Table 1.

Jan 1, 1950

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated mineral-spyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying 1 per cent is considered good grade; 0.7 to o.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent WO3 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 6o to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By N. O. Taylor

THE failure, by swelling, of several cast aluminum-zinc, spiral, pump rods, used to circulate water in a constant-temperature bath, brought up the question as to whether the presence of tin in varying quantities would have any appreciable influence in controlling this action. Previous workers had found the same difficulty with aluminum-zinc alloys, due to their swelling in water or solutions of electrolyte^.^ It was known that pure aluminum was practically insoluble in concentrated sulfuric and nitric acids, presumably due to the formation of an oxidized film on the surface. Concentrated sulfuric acid had little or no effect on pure zinc and tin and concentrated hydrochloric acid would attack all three metals. These facts aroused curiosity as to the probable reaction of the ternary alloys of these metals, and tests were made to determine their resistivity to the action of common laboratory reagents. Samples, covering the entire range of the ternary series of aluminum, zinc and tin alloys, were made up from good grades of the commercial metals.2 The materials were melted, at as low temperatures as possible, in graphite crucibles in a gas-fired crucible furnace. Graphite crucibles were used in preference to clay, to prevent the absorption of silicon by the aluminum, as found by previous workers. The melted materials were stirred thoroughly with pine sticks in order to ensure complete mixing and the greatest possible freedom from oxidation, and were cast in sectional, iron molds giving bars % in. in diameter and 5 in. long.

Jan 1, 1927

By A. B. Kinzel

ALTHOUGH calcium carbide and other compounds of calcium, as well as a number of calcium alloys, are well known and are the basis of important industries in the of United States, calcium metal has been thought of as something of a rarity and has received comparatively little attention from industrial metallurgists. The metal may he made in a number of ways, but the electrolytic deposition of calcium from a molten calcium chloride bath was the first process to be used for its commercial production and is still the standard procedure. Calcium metal has elicited little interest among nonferrous metal producers, as the demand has been relatively small and its production restricted to only a few plants, exclusively in France and Germany.

Jan 1, 1941

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of complaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and insure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage o~ breakage en route. The small sizes present in a car-of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers&apos; loss because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal. An Ohio dealer estimates the degradation in loading and shipment of West Virginia coals consigned to Ohio cities as follows: Pocahontas lump

Jan 1, 1950

By E. L. BROKENSHIRE

FLUORSPAR, a little known non-metallic mineral, referred to technically as fluorite, chemically as calcium fluoride, is a compound of calcium and fluorine in the ratio of one molecule of calcium to two of fluorine. By weight it is composed of 51.3 per cent of calcium and 48.7 per cent of fluorine. Its specific gravity is 3.2. It is brittle, has a hardness of four and can be easily scratched with a knife. It weighs about 200 Ib. per cubic foot and has a melting point of 1650" F. The color of fluorspar ranges from pure white and opaque white, according to its purity, to various hues of yellow, green, pink, lavender, blue and brown, to bluish black. Although the lumps have color, when ground the fluorspar becomes pure white. The reason for this is because the mineral usually carries no fixed pigment, the color being produced by the re- fraction of light rays within the crystal structure and small quantities of organic matter which readily oxidizes. It crystallizes in the isometric system with perfect octahedral cleavages.

Jan 1, 1929

By E. Orowan

LONG before the role of dislocations in the plastic deformation of crystals was recognized, the stress-strain field around dislocations received considerable attention in the theory of elasticity. It seems that Weingarten1 was the first to consider dislocations as simple and typical sources of internal stress in elastic solids, and Volterra2 and Timpe3 investigated their elastic field. Fig 3-1 shows the two basic types of dislocations considered by Volterra. The first arises by making a straight-edged .plane cut in a solid, displacing the two surfaces of the cut in their own plane relatively to one another by a constant amount in a direction perpendicular to the edge, and welding them together; this is shown in Fig 3-la, where the outer cylindrical surface represents the boundary of the solid, and the thin spiral cylinder around the edge of the cut has been removed in order to avoid infinities of stress and strain. The second type of dislocation is shown in Fig 3-lb; here the surfaces of the cut have been displaced relatively to one another by a constant amount parallel to the edge, and then welded together. After J. M. Burgers,4 these two types are called edge and screw dislocations, respectively. They represent simple limiting cases; in the general case, the surfaces of the cut are displaced by a constant vector that lies in the plane of the surface but has components both parallel and perpendicular to the edge of the cut. This vector is the Burgers or slip vector. The name “dislocation” was given by A. E. H. Love;5 it was bor-

Jan 1, 1954

By E. J. Duggan

CLIMAX ore is an altered and highly silicified granite, about half of the gangue being quartz. Molybdenite is the only mineral recovered and most of it is intimately associated with the quartz in fine veinlets. Other minerals are molybdite, pyrite, and chalcopyrite. Although the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make this profitable. The pyrite ranges from 2 to 5 per cent and the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the problems is its elimination, and that of pyrite iron, from the final product. On account of the high degree of dissemination of the molybdenite and the necessity of eliminating the iron and copper, fine-grinding followed by flotation is the only known feasible method of concentration. Two factors, peculiar to Climax ore, have a predominating influence on the metallurgical attack: (1) Molybdenite is one of the most easily floated minerals. High recoveries may be made with pine oil alone if the

Jan 1, 1946

By AIME AIME

THE growth of the spirit of progress and mutual aid which motivated the founders of the Institute sixty years ago in Wilkes-Barre was vigorously demonstrated at the sixtieth anniversary meeting held there on May 22. Committees headed by Cadwallader Evans, "resident director" of the Institute, and Paul Sterling, chairman of the local section, had arranged for a full-day tour of the northern anthracite field, so that the hundred and fifty members and guests who had come for the celebration of the anniversary might see the changes and progress made in that field in recent years. More than forty automobiles were in line in the cavalcade which left the Westmoreland Club at nine- thirty. Operations visited were fully described in the May issue of MINING AND METALLURGY, so it is enough to say that after a seventy-five mile drive through the beautiful Susquehanna Valley and over the rolling green hills of northern Pennsylvania a stop was made for lunch at Forest City. Carey, Baxter and Kennedy, contractors at the stripping operations there, had provided, in the shelter of tents, a well-prepared luncheon and other refreshments. The return trip was made by way of Scranton, arriving at Wilkes-Barre at five- thirty.

Jan 1, 1931

By W. P. Lass

The purpose of this article is not only to describe the plant and method of cyaniding the Treadwell concentrates, but to present some of the results of the experimental work obtained in the past three years for the Alaska-Treadwell Qold Mining Co., at Douglas Island, Alaska, under the direction of F. W. Bradley, Consulting Engineer, and Robert A. Kinzie, General Superintendent, of the affiliated companies. At the time the experimental work was undertaken the concentrates were being shipped to the smeltery at Tacoma, Wash., and the cost for treatment of 3-oz. (gold) concentrates was $11.95 per ton, divided as follows : Smelting-charges,......... $4.00 Loading, freight, insurance, etc., . 2.89 Interest due to time loat in transit and in settlement,... 0.05 Loss due to settlement for 95 per cent. of the gold at $20 per ounce, 6.01 Total,...$11.95 From the experimental work described later, it was estimated that 96 per cent. extraction could be made by treatment on the ground, and that the cost, when treating 80 tons per day, would be $3.25 per ton, divided as follows : Per Day. Per Ton. Labor,. $86.16 $@.827 Chemicals,.76.60 0.960 Power and steam-heat,... 67.60 0.845 Marketing-, refining- and other charges, . 49.36 0.617 Totals,.. $2.59.72 $3.250 Adding to this total the 4 per cent. treatment-loss, which on 3-02. concentrates amounts to $2.48, gives a total cost of $5.13 per ton. Comparing this with $11.95, the cost when shipping to the smelter, leaves a net gain of $6.22 per ton by the local

Jan 1, 1912

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others.

Jan 1, 1950

By W. W. Duecker

SULPHUR is a peculiar combination of a nuisance and a useful element. Most of the nonferrous metallic ores contain large amounts of it in the form of sulphides, which the metallurgist has wasted up the chimney, since the sulphur dioxide formed is generally too dilute to make recovery economical and practical. Iron ore does not contain much of the unwanted sulphur; in pig iron and coke it is most unwelcome. Gold metallurgists can get along nicely without sulphides in their cyanide plants and yet they find matte-a sulphur compound -an excellent collector for gold and silver in base-metal smelting. Also, sulphur appears in the non-metallics as in barite, gypsum, Glauber&apos;s salt, and celestite, all to useful purpose.

Jan 1, 1938

By George W. Friesen

This paper presents the historical trend and de- fines the causes of drilling cost escalation in the Gulf of Mexico during the 1970&apos;s. The three major components of escalation are: 1) inflation, 2) supply-demand imbalance (demand pull) and 3) decreases in drilling efficiency. The decade was divided into three periods. During each period one component of escalation was responsible for most of the rise in costs. From 1970 through 1973 only inflation pushed costs upward. During 1974 and 1975 a supply- demand imbalance caused most of the escalation. Since 1975, decreases in drilling efficiency have produced the major component of escalation. During any one year or period of years, the sum of the three components will give the total escalation rate. The reasons why different components contribute more toward escalation during certain years than others are shown by following the timing of oil and gas price increases, the overall quality of the acreage offered each year in offshore lease sales and the resulting drilling activity.

Jan 1, 1982