Search Documents

By S. Stopek, E. D. Hinkley, R. H. Rediker

Epitaxial heterojunctions have been prepared by melting the lower -melting-point semiconductor of the interface between two dijferent semiconductors. when the temperature is reduced, the melted material recrystallizes, having alloyed into the higher -melting-point semiconditctor. The electrical and elcctro-optical properties of such single-crystal heterojunctions between GaAs and Gash and between p-type InAs and n-type Gash are the subject of this paper. The forward current varies as exp (AV), where A is substantially independent of temperatuve. For Gds-Gash heterojunctions at temperatures above, 370°K, if the current-voltage relationship were to he expressed as exp (qV/nkT), then n would he less than unity. The injection luminescence associated with forward current is, for the most part, characteristic. of the lower bandgap semicondutctor. These results can he explained by carrier injection into the lower bandgap semiconductor by tunneling through a barrier at the interface. The photovoltaic effect measured for incident photons having energies in the range between the bandgaps of the two semiconductors is much smaller than that produced by higher-energy photon The smallness of this between -the-gap photovoltaic response can he explained by the low probability for penetration of the barrier by the carriers produced in the smaller -bandgap semiconductor. THE technique of interface alloying has been used to produce single-crystal junctions between dissimilar semiconductors.' Oriented wafers are placed on a carbon heater strip, Fig. 1. so that semiconductor S1, which has the lower melting point, is supported by semiconductor S2. Electrical current passed through the heater strip produces a temperature gradient such that S2 is at a higher temperature than S1. As the temperature is raised the lower face of S1 begins to melt. Before the entire wafer can melt, however, the heater-strip current is turned off and, as illustrated in Fig. l. the melted portion recrystallizes, having alloyed into S2. Junctions have been fabricated by the above procedure between GaAs and germanium, between GaAs and GaSb, and between InAs and GaSb. Mroczkowski, Lavine. and Gatos have described the metallurgical and chemical aspects of the GaAs-Ge junction.2 The transition from GaAs to germanium is not monotonic and a portion of the recrystallized region consists of the GaAs-Ge eutectic. Since gallium is an acceptor and arsenic is a donor in germanium, since germanium dopes GaAs, and since the electrical properties of the GaAs-Ge eutectic have not been investigated, any interpretation of the electrical characteristics in terms of simple heterojunction theory would be incorrect. That the rectification of GaAs-Ge heterojunctions is not a property of the impurity doping of the GaAs or the germanium, but is most probably due to the impurity distribution in the recrystallized region, is clear from the fact that forward conduction occurred for all the GaAs-Ge interface-alloy junctions (whether they be n-n,n-p. p-n. or p-p) when the germanium was biased positively. The electrical characteristics of these GaAs-Ge heterojunctions will not be discussed further in this paper. Electron-beam microprobe analysis of GaAs-GaSb heterojunctions showed that the transition from arsenic to antimony atoms was without structure. and that the transition occurred within a 2 to 3 region.' In this paper we will describe the electrical properties of the GaAs-GaSb heterojunctions as well as electrical and electro-optical properties of the InAs-GaSb heterojunctions. A band model for the junction will be proposed which can explain these properties. ELECTRICAL PROPERTIES OF GaAs-GaSb HETEROJUNCTIONS After interface alloying. in preparation for the electrical and electro-optical experiments, ohmic contacts were made by conventional means. For example. Kovar tabs clad with tin were alloyed to n-GaAs or similar tabs clad with Au-Zn were alloyed to p-GaAs. The units were mounted and then etched. All four combinations of conductivity types

Jan 1, 1965

By H. M. Otte

Certain choices for the shear elements of the inhomogeneous distortion in the phenomenological theory of martensite formation are examined for their agreement with crystallographic and X-ray data of iron alloys. The assumption that the shear elements must represent slip or twinning systems characteristic of bcc metals is found to covey all observations, even when a small uniform dilatation is taken into consideration. In bct martensite, (011) becomes a possible twinning or faulting plane, in addition to {112), and qualitatively similar X-ray line broadening is to be expected from both. The basic concept inherent in the current theoriesl-4 of the formation of martensite is that the interface between the parent (austenitic) and product (martensitic) phase is an invariant strain plane (i.e., one that is undistorted and unrotated). Experimental evidence that the interface is of such a nature is available in certain transformations2'5'6 but for the transformation in iron alloys direct observation has not proved enlightening. Internal strains resulting from the formation of the small martensite platelets within the parent austenite matrix7 make it difficult to produce the desired evidence. Indirect evidence, however, such as the continuity of scratches in passing from untrans-formed to a transformed region, strongly indicates that the habit plane in iron alloys is an invariant strain interface. The scatter in habit planes in a given specimen8 would suggest that internal stresses have a slight but definite influence. On the other hand, composition changes which affect the lattice parameter can alter the habit plane appreciably, and by an amount greater than the scatter.' The success of the theories depends on the choice made for the "inhomogeneous distortion" or "complementary shear'' in the analysis and also on the choice for the parameter 6 representing a small uniform dilatation. In the approach developed by Wechsler, Lieberman, and Read'," it is implicitly assumed that 6 is unity. In the case of iron alloys, all observations cannot be explained without varying either the inhomogeneous distortion or 6 . Bowles and Mackenzie3 considered only the effect of varying d. They found it difficult to reconcile the wide scatter of habit planes with the theory and were forced to the conclusion that it may also be necessary to consider variations or different choices of the inhomogeneous distortion. Wechsler and Read" considered a limited number of possible choices for the inhomogeneous distortion, but no variation in 6, though this could easily have been introduced if so desired. It is the purpose of the

Jan 1, 1961

By Russell C., Fleming

FOK, many years the officials of the Magma Copper Co. mine at Superior, Ariz., have had to contend with adverse conditions underground in the form of high rock temperatures, hot water, and high relative humidity. These conditions in the mine have been such that working the mine would have been impossible were it not for the constantly expanding and improved sys- tem of ventilation to produce bearable conditions in the working places. Results that have already been achieved make an interesting study of what can be done along those lines. From the time the mine was first opened in 1910 it has been hot. An idea of the conditions that have persistently been encountered can be obtained from parts of the mine that are not being worked at present or that do not yet have sufficient ventilation. Virgin rock temperatures as determined in drill holes at the faces range from 104° to 116°*. An observation made at the face of No. 5 West footwall drift on the 2800-ft. level.

Jan 1, 1930

By K. T. Aust

It is proposed that the intergranular corrosion of austenitic stainless steels is associated with the presence of continuous grain houndary paths of either second phase, or solute segregate resulting from solute-vacancy interactions. Experimental observations of structural changes and crrosion behavior of different types of austenitic stainless steel provide support for this poposal. On the basis of this model, it is shown that the intergranular -corrosion susceptibility of austenitic stainless steels in nitric-dic hromate solution may be substantially reduced either by suitable heat treatments or by impurity control. AUSTENITIC stainless steels, such as Type 304, generally have excellent corrosion resistant properties when properly solution heat-treated and used at temperatures where carbide precipitation is slow. However, several corrosion environments have been found which produce intergranular corrosion of solu-tion-treated stainless steels, that is, those steels with no detectable carbide precipitation.''2 Of the various corrosion environments, the most widely used test solution has been the boiling nitric-dichromate solution. In these acid solutions, stainless steels have been found to be susceptible to intergranular attack despite the addition of carbide-forming elements such as titanium or columbium, or despite lowering of the carbon content or use of high-temperature solution treatments. Studies of the electrochemical mechanism of corrosion attack have been made by several worke1s3'4 who found that oxidizing ions such as crt6 depolarize the cathodic reactions and consequently raise the open-circuit potential of stainless steel immersed in nitric acids. As a result of this, the anodic reaction is accelerated. The reason for the localization of anodic activity at the grain boundaries, and resulting intergranular corrosion, has not been conclusively determined. Several workers, e.g., Streicher,3 and Coriou et al.,4 have suggested that the strain energy associated with grain boundaries provides the driving force for the accelerated intergranular corrosion. This argument would predict that alloys of high purity would still be susceptible to intergranular attack. However, work by chaudron5 and by ArmijO,6 has shown that high-purity alloys are immune to attack, in disagreement with this argument. An alternative suggestion is that chemical concentration differences exist between grains and grain boundaries, that is, impurity segregation at boundaries, and that these chemical differences provide the driving force for localized attack. It is this impurity segregation which can lead to accelerated dissolution of grain boundaries when the alloy is exposed to a suitable corrodant. This mechanism would predict the immunity of high-purity alloys to inter-granular attack, which is in agreement with experi-mental observations. In the present paper, some recent studies on inter-granular corrosion of austenitic stainless steels which were conducted by coworkers and myself will be re-tibility A simple model will be described in which it is proposed that the intergranular corrosion of aus-tenitic stainless steel is associated with the presence of continuous grain boundary paths of either second phase or solute-segregated regions.* On the basis of this model, it is suggested that the intergranular corrosion rate can be markedly reduced by the formation of a discontinuous second phase at the grain boundaries if the discontinuous second phase incorporates the major part of the segregating solute, drained from the grain boundary region. Results are presented of corrosion tests and electron microscopic studies of different types of austenitic stainless steel after various heat treatments which provide experimental support for this model. Finally, a solute clustering mechanism, based on a solute-vacancy interaction, is shown to be consistent with the results obtained for inter-granular corrosion of solution-treated austenitic stainless steels. EXPERIMENTAL Corrosion tests using weight loss measurements were made on sheet specimens, which were lightly electropolished, washed, and immersed in boiling (115°C) 5 N HN03 containing 4 g crt+6 per liter added as potassium dichromate. Studies in which the inter-granular penetration depth was measured both by electrical resistance and metallographic methods have shown an empirical correlation between the rate of intergranular penetration and the weight loss per unit time for identically treated specimens of stainless steel." As a result, although all the corrosion data reported here are in terms of simple weight loss measurements, these data are considered to reflect primarily the rate of intergranular dissolution. Fig. 1 shows a typical result of intergranular attack of a solution-treated Type 304 stainless steel after 4 hr in a boiling nitric-dichromate solution. The wide grain boundary grooving at the surface, and the attack at incoherent twin boundaries, are evident; very little corrosion attack is seen at the coherent twin boundaries. INTERGRANULAR CORROSION MODEL

Jan 1, 1970

By G. B. WATERHOUSE

THE year 1929 was exceedingly busy and prosperous for the iron and steel industry in the United States. The lake shipments of ore were approximately 65,000,000 tons, steel ingots produced were about 57,000,000 tons. Plants were very active. operating for many months well over their rated capacity, slowing down during the last quarter following the severe break in the stock market. The ore tonnage mentioned above was the greatest ever shipped by lake from the Lake Superior region. The trend at the ore mines has been to supplement manual labor by mechanical appliances as much as possible. Mining methods have been greatly improved along the lines of safety as well as to increase the percentage of ore recovery. Crushing and grading of iron ores continued to gain in popularity inasmuch as remarkable blast-furnace operations and records were obtained with sizing and uniformity of raw materials. Progress was made along other lines. The Bradley process for the separation of manganese osicle and iron oside from siliceous manganiferous iron ore was cleuelopecl; also considerable work was clone on a process for the beneficiation of the Cuban laterite ores. Sintering of ores and concentrates increased in popularity. A new analytical method for the deter- mination of sulfur in iron ore was worked out which reduced the time required appreciably. The ore re- serves of the Lake Superior district continued to receive considerable attention and played an important part in the recent mergers which have taken place in the iron ancl steel industry.

Jan 1, 1930

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By Walter R. Hibbard, Ming-Kao Yen

VARIOUS rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two,1 three,2 five,4 an indefinite number,5 and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, † the necessity for the operation of slip systems capable of producing the required, changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: I. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, - the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only-not translation, inversion, nor others-is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal dose-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1948

JESSE L. JONES, ? Pittsburgh, Pa. (written discussion?).-From a commercial standpoint, the most important characteristic of the electric furnace is the ease with which it lends itself to intensive production. The melting of non-ferrous metals, as usually clone in crucible, open-flame, reverberatory, and similar furnaces, has certain disadvantages which are absent in the electric furnace, viz.:

Jan 4, 1919

Jan 1, 1947

Jan 1, 1947

By John Chipman, Eric R. Jette, O. B. Ellis

IN the study of the chemical reactions occurring in the open-hearth furnace, it is frequently assumed that a condition of equilibrium between slag and metal is attained. In order to test this assumption it is necessary to have dependable operating data as well as an exact knowledge of the equilibrium state. Considerable progress has already been made in the study of slag-metal equilibria, notably in the earlier work of Herty1 and of Oberhoffer and Schenck2 and in the more recent researches of Krings and Schackmann3 and of Koerber and Oelsen.4 None of these investigators, however, have employed basic slags comparable to those encountered in basic open-hearth practice, so that up to the present time our only information regarding the equilibria of these slags is based upon observations drawn from steelmaking practice in which there is little assurance that actual equilibrium was attained. The original plan of this investigation was to secure simultaneous slag and metal samples at intervals during the making of an open-hearth heat, recording the heat history in detail and obtaining complete analyses of slag and metal, then to bring these slag samples into equilibrium with liquid iron in the laboratory induction furnace and thus to determine directly whether or not the observed relationships in the open hearth represent conditions approaching equilibrium. This plan was only partly successful. While slags were obtained from the open hearth under satisfactorily recorded conditions and these were remelted in the laboratory under equilibrium conditions, changes in slag composition, which accompanied the remelting operation, were so great that the final slag from the induction furnace bore little resemblance to its open-hearth parent and the direct comparison was therefore abandoned. The results, however, lie within a range of slag composition that is of interest in the making of low-carbon steel. As far as we are aware, they represent the first published laboratory study of equilibria involving slags that contain all the constituents of basic open-hearth slag. EXPERIMENTAL HEATS The first set of measurements on slagmetal equilibrium was made in the Research Laboratories of the American Rolling Mill Co. at Middletown, Ohio. This will be known as series A. The second set was made in the Metallurgical Research Laboratories at Massachusetts Institute of Technology, and will be referred to as series B. Series A.-The induction furnace used has been described.5 Approximately I kg. of a special ingot iron containing less than

Jan 1, 1941

By Allen Garrison

A PREVIOUS paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their com-position, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions, Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. EXPERIMENTAL PROCEDURE The difficulties involved in the measurements of the flow character-istics of plastic fluids are too familiar to recite, The possible applications of some of the well-known instruments to this problem have been ade-quately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measure-ment of clay or shale suspensions, Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first require-ment is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1939

By Leon Dominian

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. THE lack of Aryan roots for the names of metals commonly known among the Aryan settlers of Asia Minor, as well as the later colonizers of Europe, indicates that these races were generally ignorant of the use of metals until they came into contact with Semitic peoples. Practically all mining-terms in current use among the earliest Greeks resemble very strongly their distinctly Semitic equivalents, which can be traced all the way in a broad belt beginning in Lower Mesopotamia, and extending westwardly to the Syrian shores of the Mediterranean. The Greek word " "metallon," for instance, used indiscriminately to designate mine or ore, probably came from the earlier Semitic equivalent, " matal." Again, the Greek words " chrysos " (gold) and " chalkos " (copper) seem to be descended from the Semitic forms " throats " and a chalak." It is a natural inference that primitive mining-methods were evolved by the dwellers in the mineralized areas of Asia Minor, from whom later Greek, Roman, and even North European miners obtained their first notions of the reduction of metallic ores, by virtue of a general westward migration of mining and metallurgy. Some traces of its passage through Turkish territory will be noted in this paper. While European Turkey can boast of one ancient gold-field, the Asiatic dominions of the Sultan may lay claim to at least two well-defined and widely-separated gold-producing districts. These three regions may be distinguished as the Thracian, the Pontic, and the Anatolian gold-fields. II. TURKEY IN EUROPE. . The Thracian Gold-Field. The most conspicuous topographic feature of the lowland between Constantinople and Salonica is the uplifted Archaean

Nov 1, 1911

By CHARLES SIMENSTAD

COAL preparation, or coal washing, is not a new subject to the Pacific Northwest. Most of the coals mined in this state smaller than lump, and nearly all such sizes mined on the Pacific slope of the Cascade mountains, require washing before marketing. A large proportion is being put through some washing process, but coal washing in this state, has not reached the efficiency it is practicable to obtain. In fields where the coal, as mined, contains less impurities, where working conditions make it practicable to eliminate some of these impurities under- ground, or where a large proportion of the run-of-mine coal is lump, coal preparation does not present the problem it does in our local field. Here the coal is associated with considerable impurities and the slack, or steam sizes, aggregate about 80 per cent. of the output. Therefore, approximately 80 per cent. of the coal mined must be washed to become a valuable fuel. Washing then becomes a major operation, as hand picking of the 20 per cent. of lump is a standard and comparatively simple operation. Some coal beds here are so interstratified with bone, of a more or less massive nature, that hand picking of lump is not economically efficient. In such cases the coal must be crushed fine enough for it to be freed from the bone, so that the two may be separated. Coal cleaning in this field, therefore, must receive skilled attention to purify this fuel and raise its stand- ard. Without greater efficiency in cleaning, the importation of coal from outside the state will be even greater than in the past.

Jan 1, 1926

I. PRESIDING OFFICER. At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, Shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents, Shall preside. If none of these be present the meeting Shall elect a Chairman. The President Shall do and perform Such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. IL ORDER OF BUSINESS. At each business meeting of the Institute the order of business Shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment Shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary Shall keep a record of the proceedings of all the meetings of the Institute. He Shall be custodian of the corporate Seal, of the minute books and of all the legal documents belonging to the Institute. He Shall have charge on behalf of the Institute of all correspondence. He Shall notify all Officers and Directors and all members of committees of their election and appointment; Shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and Shall, in calling Special meetings of the Directors, Specify the objects of Such meetings. He Shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary Shall be custodian of all technical or Scientific papers Submitted to the Institute for its consideration and Shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and. of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There Shall be kept under his direction an account

Jan 1, 1925

By M. J. Pool, P. J. Spencer, J. R. Guadagno

THE present work was carried out as part of a general program to study the magnitude and concentration dependence of exothermic heats of solution of various metals in liquid tin. Thermodynamic data for the Te-Sn system are very limited, particularly for dilute alloys. Indeed, apart from the prior heat of solution determinations of Pool,1 the only other published values are those of McAteer and seltz2 who carried out electromotive force measurements on solid alloys of compositions from 75 to 95 at. pct Te at temperatures between 543° and 668° K, of Colin and Dro-wart3 who made mass-spectrometric studies of the vapor in equilibrium with solid SnTe, and of Robinson and Bever4 who determined the heat of formation of SnTe by solution calorimetry. The present work thus provides further thermodynamic information for this system, specifically in a temperature range where the solubility of tellurium is very limited. The liquid metal solution calorimeter used in this investigation has been described previously.&apos; No further discussion of its design or operation will therefore be given here. For each series of measurements a tin bath consisting of approximately 70 g of 99.99 pct pure Sn was carefully weighed out and inserted in the calorimeter which was maintained at the desired temperature to within ± 1/4°c. Tellurium, of 99.999 pct purity, was supplied by Atomergic Chemetals Co., a division of Gallard-Schlesinger Chemical Manufacturing Corp. Approximately 0.0006 to 0.001 g-atom specimens of tellurium were used for each experimental run and these were added to the calorimeter from a temperature of 273" K. Heat of solution values were calculated by analysis of a strip-chart recorder plot of the heat effect accompanying the solution of each sample in the tin bath. The heat capacity of the latter was determined at regular intervals during a series of tellurium drops by using pure tin or tungsten calibration samples, the heat contents of which were obtained from the standard compilation of Hultgren et al5 The composition of the bath was calculated after each drop from a knowledge of the weights of tin and tellurium added. Values of the heat of solution of tellurium at 725" and 775° K are listed in Table I together with the corresponding tellurium contents of the alloys. The data are also plotted as a function of tellurium concentration in Fig. 1, which includes the equivalent data obtained by pool&apos; at 750° K. It can be seen that the heat of solution remains

Jan 1, 1969

By M. J. Marcinkowski, D. Koskimaki, A. S. Sastri

THIS is the second in a trilogy of investigations carried out in order to understand the solid state transformations and their accompanying effects on the deformation behavior of near-equiatomic Ni-Ti alloys. The first stage of this effort has dealt with the strictly martensitic structures obtainable in these alloys, i.e., those in which diffusion processes were not involved.1,2 These martensites could be produced either by rapid quenching or by plastic deformation of the originally B2 type phase. The present investigation, on the other hand, will deal with those transformations in Ni-Ti which do involve diffusion. A majority of investigators3-10 have shown that the B2 modification of TiNi, which is stable at elevated temperatures, decomposes into one or both of the intermetallic compounds NiTi2 and Ni3Ti below about 650°C. On the other hand, this has been disputed by several Workers was undertaken in order to resolve this discrepancy, as well as to shed more light on the nonmar-tensitic decomposition of B2 NiTi. EXPERIMENTAL PROCEDURE Sample preparation, fabrication, and examination were the same as those described previously in Ref. 2. In addition to the 50 at. pct Ni (55.06 wt pct) hypoeu-tectoid alloy used previously, a second hypereutectoid alloy containing 54.4 at. pct Ni (60 wt pct) was also prepared for this study. RESULTS AND DISCUSSION The equilibrium diagram for the Ni-Ti alloy system in the vicinity of Ni-Ti is shown in Fig. 1. The solid lines have been established by the work of Poole and ~ume-Ftothery4 whereas the dotted lines are based on findings obtained in the present investigation as described below. Structure and Morphology. Fig. 2(a) shows a bright field transmission electron micrograph of a two-phase structure obtained in a polycrystalline Ni-Ti alloy that was furnace cooled (approx 200°C per hr) from 1050&apos; to about 300°C. Large plate-shaped precipitates can be observed in a matrix which was found by electron diffraction to possess the high temperature B2 structure. A selected area diffraction pattern of the region covered by Fig. 2(a) is shown in Fig. 2(b), while Fig. 2(c) is a detailed schematic interpretation of Fig. 2(b). The B2 matrix reflections are illustrated by squares while those of the precipitate are shown as circles. The d values associated with the precipitate reflections could be determined quite accurately since the reflections from the B2 matrix, for which the lattice constant is known precisely, were simultaneously present in the diffraction patterns. All of the reflections

Jan 1, 1970

By Edward H. Robie

PONCA CITY proved an ideal selection as a place of meeting for the Petroleum Division this fall. The accommodations at the Conoco Club were just what was required for such a gathering; the committee having the arrangements in charge functioned with the efficiency of veterans and the enthusiasm of neophytes; and the members and guests followed the speakers with close attention, entered the subsequent discussions with gusto, and divulged the "low-down" at private conferences. No one minded the drizzling rain on the first day, which only served to keep up the attendance in the auditorium; the weather then cleared up in time for a group picture before the gathering went their separate ways.

Jan 1, 1932

By R. D. Nelson, J. C. Shyne

The ß and a ß transformations in plutonium were studied with particular emphasis on the transformation kinetics and microstructure. Significant observations are: 1) The kinetic data show conclusively that the ß — a transformation in high-purity plutonium can proceed isothermally with no athermal component. 2) Plastic deformation of the stable (3 phase retards the subsequent (3 — a transformation. 3) Plastic deformation of the stable a phase accelerates the a — ß transformation; the acceleration is attributed only to residual stresses. 4) The a and a?a volume changes occur anisotroPically in textured plutonium. 5) An apparent crystallogvaphic relationship exists between the parent and the product phases of the and (3 — a transformations. 6) Both applied uniaxial compressive stresses and uniaxial tensile stresses raise the starting temperature for the ß — a transformation. 7) A given uniaxial tensile stress favors the a — ß transformation more than an equivalent applied uniaxial compressive stress opposes the transformation. These observations of the (ß —a and a — ß phase changes in plutonium are consistent with known mar-tensitic transformations. ThIS paper elucidates some of the characteristics of the a— ß and ß —a transformations in plutonium. Because considerable conjecture exists about the mechanisms by which the phase transformations occur in plutonium, experiments have been performed to provide indirect information concerning the mechanisms responsible for the a —ß and ß -a transformations. Indirect information is of particular value in the study of plutonium because of the experimental difficulties presented by the metal. Single crystals have not been produced in any of the allotropes. The large density results in high X-ray and electron-absorption factors and consequently complicating X-ray and electron diffraction. The kinetics of ß — a and a — ß transformations of plutonium and the behavior of the transformations under a variety of conditions have been investigated in detail. Information about the mechanisms of the allo-tropic transformations of plutonium was obtained indirectly from three sources: 1) the effect of plastic deformation of the stable parent phase upon the transformation kinetics; 2) the behavior of the metal transforming under applied stresses; and 3) the microstruc-tural and crystallographic features between parent and product phases. PHASE-TRANSFORMATION CHARACTERISTICS In characterizing solid-state phase transformations in metals and alloys, it is useful to define several types of transformations. An aim of the present work was to identify the low-temperature transformations in plutonium by type, i.e., as martensitic or nonmar-tensitic. Practical definitions for these terms follow. The terms commonly used to categorize phase transformations lack universally accepted definitions. This confusion arises doubtlessly because some terms specify crystallographic or morphological character while other words have a kinetic or a thermodynamic connotation. For example, martensitic specifies certain definite crystallographic restrictions. Unfortunately, martensitic is sometimes used in an ill-defined way to imply kinetic characteristics. Further confusion attends the use of such expressions as nucleation and growth, diffusional, and massive. From time to time new systems of phase-transformation nomenclature are suggested; unfortunately none of these has gained general acceptance.1,2 The authors of the present paper have no intention of entering the controversy. We recognize that some readers may object to the nomencliture used here. For exampie, the terms military and civilian have recently been used in much the same way as martensitic and non-martensitic are used in this paper. This paper is intended to describe several specific details of the low-temperature phase transformations in plutonium. The authors have found it useful to identify these transformations as martensitic; the term was chosen as the best available to describe the experimentally observed features of the transformations studied. A martensitic transformation is one that occurs by the cooperative movement of many atoms; the rearrangement of atoms from parent to product crystal structure occurs by the passage of a mobile semico-herent growth interface. The geometric features characteristic of a martensitic transformation are a specific orientation relationship between the product and parent phase lattices, a specific habit-plane orientation for the growth interface, and a shape change with a specifically oriented shear component. There is no alloy partition between the parent and product phases in a martensitic transformation. Martensitic transformations may display either athermal kinetic behavior or thermally activated isothermal kinetic behavior. Some martensitic transformations occur isothermally, although more commonly martensitic transformations are athermal. Isothermal martensitic transformations are suppressible by rapid cooling. In athermal martensitic transformations, nucleation and growth are not thermally activated and the transformations are essentially time-independent. Nucleation, growth, or both can be thermally activated in isothermal martensitic reactions. Transformation of the parent phase into a marten-

Jan 1, 1967

By T. Rosenqvist

From the chemical, metallurgical, and mineralogical points of view, the importance of thermodynamic data for metal-sulphides and sulphur dissolved in molten metal has long been realized. Such data will give a basis for thermo-dynamic calculations of processes such as roasting and the distribution of sulphur between molten metal and slags. Furthermore, it will help us understand the chemical forces which tie sulphur to the metal and to the melt. Thermodynamic studies of solid sulphides and the equilibria between solid sulphides and metals have been carried out in a rather large number of cases by several investigators. An excellent review of this work is given by Kelley.1 On the other hand, very little is known about the thermodynamic properties of molten sulphides and of sulphur dissolved in molten metal. The only system which previously has been investigated in this respect is the iron/sulphur system. The purpose of the present investigation was primarily to obtain further data for metalisulphur melts and the system silver/sulphur was chosen, not because this system was expected to be of special interest in itself, but because the silver/sulphur system is a typical example of a metal/sulphur system. Because of the low melting temperatures, the work could be carried out without appreciable furnace and refractory difficulties. The sulphur in this system possesses a rather high escaping tendency compared to most other metal/sulphur systems. By the method employed (reaction with hydrogen to form hydrogen sulphide) this gives ratios Ph2s/Ph2 up to 0.30, which may be determined accurately. &apos;rhermodynamic investigations of the heterogeneous reaction Ag2S +H2 —+ 2Ag + H2S have previously been carried out by Pelabon,2 Keyes and Felsing,3 Jellineb and Zakowski,4 Wat-anabe,6 and Britzke and Kapustinsky.6 Their results are in rather poor agreement. Experimental Part PRINCIPLE In the present invehgation the escaping tendency of sulphur from the condensed phase was determined by the reaction: S + H2 = H2S The ratio Ph2s/Ph2 is at constant temperature, directly proportional to the escaping tendency of sulphur and to its chemical activity in the condensed phase. (This ratio will subsequently be denoted by H2S/H2.) From this ratio and its variation with temperature and with change in the com- position of the condensed phase, thermodyrlamic quantities such as free energy and heat of reaction can be derived. The apparatus used is shown in Fig 1. The silver/sulphur alloy was placed in a crucible inside a refractory tube and mounted inside the furnace to the left. The tube was a part of a closed, gas-tight system in which the gas mixture could circulate until equilibrium was established. Circulation was maintained by the glass propeller to the right, driven by an external magnet, and promoted by the chimney action of the furnace. The gas passed up through the furnace, down into the crucible where it came in contact with the alloy, passed rapidly up through a narrow tube and out of the hot zone. After equilibrium was established between the gas and the condensed phase, the composition of the gas mixture was determined from its density. In its circulation, the gas mixture passed through a chamber (lower right on Fig 1) containing a buoyancy-balance, where the density of the gas was determined by magnetic balancing. From the measured density,

Jan 1, 1950