Search Documents

By J. D. Mooney

(San Francisco sleeting, September, 1915) THE accompanying chart has been drawn for the convenience of engineers as a means of quickly determining the correct number of plies of conveyor belts operating under specific conditions. The calculations are based on the average safe strength (factor of safety, 15) of the various standard rubber conveyor belts. The, calculations assume maximum loading conditions; that is, the belt is considered as carrying the greatest load that it will handle without spillage at ordinary belt speeds. This not only produces the most economical operating conditions, but also the maximum tension in the belt. The chart is a graphical representation of the formula: p = kgW (L + 1OH) Where, p = the correct number of plies k = a constant, depending on the type of drive g = the weight in pounds per cubic foot of material handled W = the width of the belt in inches L = the length of the belt in feet (approximately twice the center distance). H = the difference in elevation between the head and tail pulleys, in feet. For a simple drive, with a bare pulley, k = 1/250,000 For a simple drive, with a rubber-lagged pulley, k = 1/300,000 For a tandem dive, with bare pulleys, k= 1/375,000 For a tandem drive, with rubber-lagged pulleys, k = 1/455,000 The chart is drawn for a simple drive, with a bare pulley (k =1/250,000;

Jan 9, 1915

By B. W. Frazier

At a recent meeting of the North of England Institute of Min ing and Mechanical Engineers, during a discussion upon the com pression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

By L. F. Engle, M. A. Hewedi

SUMMARY Initial interest in using solutions of ammonium salts to leach native copper was documented in notes from an AIME meeting in 1871; By 1916-1917, application of the NH3-CO2-H2O system to recover nonferrous metals attained commercial significance, when it was used as a process for copper recovery by Kennecott Copper Corporation and Calumet & Hecla Mining Company. The Caron work in the early 1920s, Freeport Sulphur Company’s achievements leaching Cuban laterites during World War II, out- standing accomplishments in both eastern and western Canada, recovery of manganese related to the work of Dean -- all serve as landmarks as this One Century Review surveys a base for future technology. Current emphasis on compatibility of metals-producing systems with the need to meet environmental protection criteria provides special encouragement to researchers and engineers to find accept- able ways of recovering metals. The ever-present demand of management to design, build and operate facilities on a profitable basis provides additional impetus to apply information from the technical literature to that need. Examination of the general approach to this paper will reveal much that is firm and positive with respect to empirical results -- extractions, recoveries, amenability to familiar proven equipment and materials of construction common to the industry. Although there are many references, there are gaps in the basic scientific data that if filled could lead to even more usefulness; the paper attempts to indicate where further information is needed.

Jan 1, 1973

By L. Ibagos S., T. Balberyszski

The volumetric flow rate and the initial concentration of the copper sulfate solution influence the rate of reaction and, hence, the precipitation efficiency in a continuous launder cementation system. Using a model of such a system it was found that the precipitation efficiency is related to the two process parameters by the approximate expression [ log [1-n] = -[0.072 co 2.91 e – 0.511c o Q 1.15 ] N Q] where c is the initial concentration, Q, is the volumetric flow rate and N is the number of launders in the system. This expression agrees with an equation developed for the rate of the cementation process if it is assumed that the exponential factor represents the change in the surface area with concentration and the exponents 2.91-and 1.15 relate the hydrodynamic conditions and the surface concentration to co and Q. The experimental results are used to determine the values of a Precipitation Coefficient for any volumentric flow rate and initial concentration of solution. Knowing the Precipitation Coefficient, the total volume of launders that will result in a given precipitation efficiency can be calculated. It is established that maximum precipitation efficiencies are obtained for initial concentrations between 6.0 and 7.0 gpl and volumetric flow rates of approximately 350 m3 /hr Good agreement between calculated and actual launder volumes is obtained for a number of industrial operations for which a comparison is made.

Jan 1, 1973

By AIME AIME

ONE hundred and eighty-three A.I.M.E. members, W. S. Morris with an excellent technical program, John Suman, "oil" President of the Institute, and a Texas norther blew into Dallas for the fall meeting of the Petroleum Division at the Adolphus Hotel, Oct. 16-18. and the most successful result will give future meeting committees a high mark to equal. People were still talking of the terrific heat the week before and it was quite noticeable that with the lowered temperatures, the members were in fine fettle for the technical sessions. The total attendance on Friday noon was

Jan 1, 1941

By F. H. Wilson

Copper base alloys containing various amounts of aluminum and silicon are of considerable commercial interest. In particular the alloy containing 7 pct aluminum and 2 pet silicon shows an attractive combination of high strength with excellent, machinability. Since there is no evidence ill the literature that this ternary system has been studied since the recognition by Smith1 and Anderson2 in 1939 of the kappa phase of the binary copper-silicon system, the determination of the equilibrium phase relationships in the copper corner of the ternary diagram has been undertaken to provide a fundamental basis for understanding the behavior of these alloys. Phase boundaries have been determined by the micrographic examination of quenched samples while points on the liquidus surface have been obtained by thermal analysis. The results, of sufficient precision to serve their major purpose of providing a guide for the control of the manufacture of alloys in the region covered, are presented in a series of both isothermal and vertical sections of the diagram. Alloys StVdied For a rough survey of the copper corner of this ternary system the compositions listed in Table I (Series A) were employed. The results of examinations of these alloys indicated that the compositions listed in Table 2 (Series B) would further clarify regions of greater complexity. All alloys were prepared as 1200 g heats, the copper being melted under charcoal, and then first silicon and then aluminum were added. An excess of 0.05 pet silicon was allowed to cover deoxidation losses. Two small bars 5/8 by 1 1/4 by 5 1/4 in. were cast using Durville type casting equipment. Ailalyses were made on all alloys using material which was hot-rolled at 800 or 850°C and annealed 17 hr at 650°C. All analyses were found to be within 0.05 pet of the nominal composition. Since the precision of analysis is not much better than this, the points of both isothermal sections and vertical sections at fixed aluminum and silicon contents have been plotted at the compositions indicated by the nominal composition.

Jan 1, 1949

By EDBIUND U. NORTH

IN making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that. the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

By Edmund D. North

In making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

By JESSE L. MAURY

ONE OF the most hopeful features of the current depression is the discussion which it has en- gendered of ways and means to counteract similar recurrences in the future. 1t is widely recognized that fruitful attack will be directed toward the steady employment of labor, through which the purchasing power of this preponderant class in society will be maintained. S. A, Lewisohn's article' has presented the major factors to be considered; the physical suffering and mental torture endured by those who are deprived of income through no fault of their own, the direct economic losses' sustained in the degradation of 'great, numbers of our population and the disintegration of efficient working forces, and the prime responsibility of owners and managers.

Jan 1, 1931

By J. F. Mitchell, R. Bainbridge, E. A. Melvin

IN the fall of 1953, The Consolidated Mining and Smelting Co. of Canada Ltd. put into operation a completely new and modern plant for sintering the rather complex assortment of materials which comprise the feed to the Lead Smelter at Trail, British Columbia. This Lead Smelter is one section of an integrated metallurgical plant producing lead, zinc, silver, gold, cadmium and other metals. Since most of the incoming lead concentrate contains appreci- able zinc values, and most of the zinc concentrate similarly contains appreciable lead values, the cross-routing of residues or tails from the respective lead and zinc plants offers obvious advantages in recovery of metals, and has been practiced for many years. A disparity has existed, however, between the output of zinc plant residue and the capacity of the Lead Smelter to treat it, with the result that over the years a stock-pile of residue had been accumulating, and by the end of World War II had reached the formidable total of half a million tons. To treat this stock-pile, in addition to all current zinc plant residues and, of course, the regular quota of lead concentrates, became a prime objective of the Lead Smelter following World War 11. As zinc plant residue plays an important part in the operations to be discussed in this paper, some consideration of its

Jan 1, 1958

By Henry Knox

AMIDST the tumult and the shouting of the times, there are perceptible certain tendencies, quiet though serious, to take stock of the situation with a view to putting our house in order, and of these none is more encouraging than the awakening, interest in the higher education, and especially in technical education. Various committees of the professional organizations have cast much light on the matter and have pointed the way to progress and reform, but their scope is necessarily restricted by the requirements of precision and any excursion beyond these bounds must be undertaken by the unfettered individual who is free to rush in where responsible committees fear to tread. A discussion of the bearing of the higher education on character scarcely lends itself to objective treatment and yet, fraught as it is with imponderables and abstractions, the theme cannot be escaped in any com-prehensive scheme of education. The question is being pressed with growing insist-ence, why these United States, relatively to Europe, are deficient in intellectual output, and the ready reply, "Because America is a new country and Americans are too intent on developing their natural resources," is too facile and too false to carry conviction.

Jan 12, 1922

By Charles M. Rolker

It is now three years ago that I wrote a paper on the fire which broke out in October, 1880, at the Chrysolite mine, Leadville, Col orado, of which I was at that time manager. The paper was read by title at the Harrisburg meeting in 1881, and was accompanied by plans and sections fully illustrating it. It was written to invite a general discussion of the course pursued in the management of that fire, since the various fragmentary and sometimes prejudiced or inaccurate newspaper accounts were not suitable to base judg ment on. The paper I offered, gave the facts as they appeared in the contemporaneous record which I had kept. At that time, a dif ference of opinion had arisen with an adjoining mine, as to possible damages entailed through the fire; and a law suit was talked of. In view of these circumstances, the President of the Chrysolite Company advised a temporary withdrawal of my paper. Somewhat later, I withdrew it entirely, because of the unlooked-for delay in * arranging the controversy referred to. It. has now, indeed, been amicably settled; but the lapse of time has deprived the matter of much of its immediate professional interest. To the urgent request of some of the members, that I should, at least, give a description of the fire- and gas-proof bulkheads employed, I yield with some hesitation, since I lay no claim whatsoever to orig inality in these devices, and therefore question the value of such a paper. The fire originated by accident, in the Chrysolite, a mine comprising extensive and more or less irregular workings, containing immense quantities of timbering, but partially packed with waste rock or earth. This class of mines is numerously represented at

Jan 1, 1885

A. M. Strong, Bishop, Cal. (communication to the Secretary*) :—The paper of Mr. Eeyes gives us the most complete account of the geology of the borax-deposits in the Death Valley region that has yet been published, and is a valuable addition to the geological literature of a very interesting though little-known territory. During the past ten years I have been over much of the northern part of the country described by Mr. Eeyes and the region immediately north of it.

Jan 1, 1910

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By A. C. Fieldner

COKE and by-products have prime importance in the war program. The past year was marked by the construction of new and the rehabilitation of old by-product and beehive ovens and by the increase of production from existing plants to practically 100 per cent capacity. W. T. Brown's paper, "Plan to Improve Blast-Furnace Coke," presented at the Fuels Conference in St. Louis, Sept. 30, showed how the blending of low- and high-volatile coal improved the physical properties of coke and that improvement of the quality and uniformity of coke favored an increase of blast-furnace capacity- a vital need in the war program. Others in the industry have likewise increased production of coke or recovery of by- products by various innovations or changes in operation. Recognition of the value of pooling these developments for the benefit of the entire industry led to organization of a survey of coke- oven plants and blast furnaces by the Bureau of Mines in co-operation with the Solid Fuels Co-ordinator with a view to improving metallurgical coke production and recovery of by-products. This survey is being conducted with the help of an advisory committee consisting of representatives of the Bureau of Mines, the Solid Fuels Co-ordinator, the War Production Board, and the blast-furnace, coke-oven, and coal-mining industries.

Jan 1, 1943

By T. L. Johnston

MUCH has been said and written about deep mine shafts and deep drill holes as man in his search for mineral wealth digs deeper into the earth's crust. Each year some new extra depth is heralded as a record, but with unlimited possibilities of going still deeper. In contrast to "digging deep," "mining high" is limited by the height of the mountains (Mt. Everest being the maximum with its 29,000-ft. elevation) and also by the extent of human endurance. An ex- ample of what might be called near- stratosphere mining in what is probably the highest mine worked by compressed air in the world is seen in a recent project in the Andes mountains of southwestern Bolivia.

Jan 1, 1939

By Robert E. Sorenson

EXPLORATION for deep-seated orebodies in the Silver Belt area of the Coeur d'Alene mining district is complicated by meager surface expressions of diagnostic criteria, lack of knowledge of the significance of specific alteration phenomena, and the great expense involved in the exploration for ore shoots, the tops of which often occur near sea level elevation or below and as much as 4000 ft or more below the surface. Except for the early studies of Ransome and Calkins in 1903 and 1904,' little geological work was done in the Coeur d'Alene district for many years, and it is only during the last 15 to 20 years that complete and careful geological mapping has been applied to most of the mines in the area. Much early information, which now would prove invaluable, is lost in hundreds of miles of caved and inaccessible mine openings not mapped by mining geologists. In more recent years mining geology has become a tool of greater use in the district, and some measurable progress is being made in the accumulation of observations that are adding gradually to the knowledge of ore deposits in the district. The recognition of alteration phenomena and related features by Hoyt S. Gale3 in 1935, followed by the work of Shenon and McConnel in 1936-37,4 changed many of the concepts formerly held and opened the way for more critical study and mapping of alteration effects. Mapping of these effects has been in progress for several years but no well-organized, careful, and complete laboratory study of the alteration has been made by mining companies or by government agencies. Recently, Thomas Mitcham of Columbia University has been occupied in the collection and study of specimens carefully selected from several producing mines in the Silver Belt as well as from several prospects exhibiting alteration effects. Mr. Mitcham and the writer have discussed some of the preliminary results of his investigations, which indicate that definite and interesting material is forthcoming from his studies. Work of this kind, aided by careful observation by district geologists, should advance the knowledge of the environment of Silver Belt ore shoots and establish additional criteria for recognizing meager shallow expressions of deep-lying orebodies. Structural details in the Silver Belt area are extremely difficult to decipher on the surface because the area is almost completely covered by a deep mantle of surface debris and soil. A dense growth of small trees and buck brush adds to a geologist's difficulties. Often large areas reveal only scattered small outcrops with great intervening areas where the underlying formations must be deduced from small altered rock fragments. Some considerable success in obtaining surface information has come from bulldozer roads and cuts in selected areas. As this type of work receives more attention, knowledge of the surface expressions of formations, alterations, faulting, and veining is expanding and giving more reliable information to guide deeper development. Lack of diagnostic marker beds in the district contributes to a geologist's difficulties in determining fault displacements. In the Silver Belt, known commercally important sulphide orebodies commonly are associated with siderite and quartz gangue. Some of the veins at shallow horizons above productive ore shoots are composed of quartz with light-colored carbonate minerals such as calcite, ferrocalcite, ferrodolomite, ankerite, and carbonates with variable amounts of manganese. The relation of these carbonates to commercial orebodies is a problem offering possibilities for research. Shallow exposures of veins composed of quartz and the light-colored carbonates, often with some associated barite, grade into quartz and siderite veins at deeper horizons. The vertical range of these carbonates has been partially established for some veins, but no reliable method has been devised for predicting where the change in a vein may take place. Careful observation and analysis of carbonates may make it possible to predict more closely where the change to siderite may be expected. In 1926 Shannon5 pointed out some of the characteristics of the carbonate veins of the district and included a few chemical analyses. Some of the Silver Belt ore shoots have small commercial outcrops, and very shallow development of some properties has led to the opening of small ore shoots." Several small ore shoots developed at shallow depths have not been explored at deep horizons, and some important ore shoots with no commercially significant exposures at shallow horizons have been developed. The greatest problem of the mining geologist working in the Silver Belt area is to find the all-important link between the very meager shallow expressions of mineralization and the rich ore shoots that may be found below. To develop criteria for use in the recognition of the weak upper expression of ore shoots, the experience of past development programs must be relied upon heavily. The investment of more than a million dollars in the exploration for such ore shoots requires some reliable criteria if these ore shoots are to be found. Management needs some assurance that the risk involved is justified by well-developed and acceptable geological inference. The richness of some of the ore shoots found thus far has contributed greatly to the justification for a bold approach, but many negative results of blind exploration programs would lead eventually to extreme caution on the part of management. Fortunately, recent experiences of development programs have been quite successful. It is hoped that added knowledge. of the environment of Silver Belt ore shoots will contribute greatly to the sureness of approach toward their development. The Coeur d'Alene mining district is located in the panhandle of Idaho in Shoshone County. The population of the county is either employed in the

Jan 1, 1952

The opening session* was held in the hall of the Franklin Institute, on Tuesday evening, June 20th, President Holley in the chair. The President introduced Mr. Franklin B. Gowen, who addressed the Institute as follows: Mr. President and Gentlemen : It has been made my pleasant duty to welcome you to the city of Philadelphia, but in so doing I shrink, with some natural reluctance, from appearing before an audience so much better fitted than I am to cope with the subjects which are usually presented to your association, and I can assure you that no trembling neophyte, first venturing within the groves of the Academy, or walking, with sacred reverence, in the gardens of Plato, felt more natural dread at the consequence of his own temerity than I do in appearing before an audience composed of geutlenlen belonging to a scientific society of which I am but too sensible that until now I have been a member only in name. In olden times, upon entering a temple sacred to the worship of any deity, it was customary to lay some offering upon the altar, and, in following this custom, it will be my duty, before entering upon the more pleasant part of the task which is assigned me, to call your attention to a subject with which I have been somewhat familiar, and which is entirely within the scope of your investigations, in the belief that I may throw out some hints or some suggestions of a process that may be fully developed by some of you, and eventually lead to the introduction of that which may be of service to the human race. The satirist who described the philosopher whom he met, as engaged in the process of extracting sunbeams from cucumbers,

By R. Philip Hammond

MONAZITE has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent-thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. OCCURRENCE Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatites and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. COMPOSITION OF MONAZITE As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium [ ] group of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1946

By E. J. Rapperport, J. P. Pemsler

Proton irradiation of high-purity distilled berylliuwz was utilized to introduce various hydrogen contents from 0.00075 to 0.075 at. pct (0.83 to 83 ppm) in a band 0.004 cm wide. After irradiation, the specimens were heat-treated to effect hydrogen agglomeration. Observations of agglomerates in all specimens of the lowest hydrogen content indicate a hydrogen solubility of less than 0.83 ppm in the temperature range 350" to 1050°C. Estimates of the inter diffusion coefficient in the hydrogen solid solution of beryllium were obtained from measurements of the dimensions of hydrogen-depleted zones survounding agglomerated bubbles. A value of (approximately) 3 xlo-' sq cm per sec is obtained for the diffusion coefficient at 850" to 900°C. PREVIOUS investigators found that We solubility of hydrogen in beryllium is very small. Gulbransen and Andrew' state that beryllium does not react with hydrogen at 23 mm Hg between 300" and 900°C. Cotter ill et a1.' report that as-machined beryllium has an adsorbed hydrogen layer of 0.007 cu cm per sq cm of surface. No additional hydrogen is picked up in hydrogen at 0.1 mm Hg and between 200" and 80O°C, or when hydrogen is bubbled through molten beryllium. Beryllium hydride has been reported to exist in an ether solution,394 but decomposes at about 200°C; there is no substantial evidence for the existence of the hydride in the solid phase.

Jan 1, 1964