Search Documents

By Benjamin N. Webber

THE peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guana¬caste, which is the northern of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guayjiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. PHYSIOGRAPHY In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active; (2) the Atlantic lowlands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from 0 to 800 ft. Topography is of the mature type of wide valleys and low ,hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. HISTORY AND PRODUCTION The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1942

By M. I. Jacobson, A. S. Yue, A. E. Vidoz, F. W. Crossman

An equation governing the concept of constitutional supercooling under the combined effect of concentration and temperature gradients was used to produce platelike Al-CuAl2 eutectic composites for mechanical properties studies. Compression specimens were prepared from a single-colony Al-CuA12 eutectic composite ingot, 2 in. in diam and 12 in. long. The specirrzens were cut such that the platelets were oriented parallel, 45 deg, and perpendicular to the compression direction. Since the ingot was of eutectic composition, The aluminum-rich matrix could dissolve 5. 7 wt pct Cu in solid solution, and therefore could be strengthened by precipitation hardening. Specimens were tested at room temperature and elevated temperatures in the unidirectionally solidified, solution-treated, and solution-treated plus aged conditions. The results were compared with those for the conventionally cast and extruded specimens. For the controlled material, the highest strengths were obtained with platelets oriented parallel to the compression axis. In the unidirectionally solidified condition, 0.2 pct offset yield strength was 32,000 psi; however, this was increased to 59,000 psi by solution treatment, and further increased to 90,500 psi by solution treatment and aging. The attainment of high compressive strengths in the Al-CuAl2 eutectic composites was interpreted in terms of the buckling of elastic CuAl2 platelets in the plastically deformed a aluminum matrix. SINCE the discovery of high-strength whiskers,' scientists and engineers have made significant progress toward incorporating these whiskers into metallic matrices, forming composites for basic studies and structural application. The general procedure is to produce the whiskers first and then to bind them together with a ductile matrix. The production of whisker-reinforced composites requires tedious handling techniques,, particularly when it is desired to align the whiskers unidirectionally. Furthermore, the interfacial bond between the whisker and the matrix is frequently poor3 so that the resulting composite has strengths lower than expected. These disadvantages are generally true for any metallic composite produced by physically mixing the components. It is possible to eliminate these shortcomings by growing whiskers directly in the matrix material by eutectic solidification.4-8 In eutectic solidification, the matrix phase and a whisker phase are grown approximately simultaneously from a liquid of the same overall composition at the eutectic temperature. If the solidification process is controlled by varying the freezing rate, the temperature gradient, and the impurity content, platelike or filamentlike whiskers are produced parallel to the growth direction. The morphology of the grown-in reinforcement, i.e.. plates or rods, generally depends on the volume fraction9 of the dispersed phase present in the eutectic mixture. Since the unidirectional eutectic solidification is a one-step process, i.e., the liquid-solid transformation process, an excellent interfacial bond between the matrix and whisker is obtained. An additional advantage is that no special handling technique for whiskers is needed. In recent years, many investigators10-13 have studied the effects of growth variables on the micromorpholo-gies of binary eutectic alloys produced by controlled solidification. The study of their mechanical properties was initiated by Kraft and coworkers14-16 who found that the strength of cast A1-CuA12 eutectic alloy can be increased threefold by unidirectional solidification. In the A1-AL3Ni system, a strength of 50,000 lb per sq in, was reported for the unidirectionally solidified eutectic alloy, a value five times higher than for conventionally cast material. Thus, the unidirectionally solidified eutectics can be used as fiber-reinforced composite materials. In this paper, we shall first use an equation17 as a guide for the production of eutectic composites in general and the Al-33 wt pct Cu eutectic in particular. Experimental data supporting the theoretical prediction are given. Second, the compressive properties of the grown A1-33 wt pct Cu eutectic were thoroughly investigated in terms of platelet orientations, thermo-mechanical treatment, and temperature. The experimental data are interpreted in terms of a buckling model of fibers in elastic fiber-plastic matrix metallic composites. EXPERIMENTAL PROCEDURE Crystal Growth. The following experimental procedure was adopted for the production of controlled microstructures in the A1-33 wt pct Cu eutectic alloy. The controlled solidification was accomplished with a movable resistance-wound radiation furnace. Fig. 1 is a schematic drawing of the solidification apparatus. A water-cooled chiller was placed into a degassed high-purity graphite crucible containing the charge. Rubber stoppers wrapped with aluminum foil were used to seal both ends of the quartz tube through which a dried argon atmosphere was passed under a slight positive pressure. At both ends of the quartz tube, radiation shields were used to minimize heat loss. The quartz tube was held in place by two steel clamps and the furnace was drawn vertically by means of a steel cable against the steel truss which permits the furnace to move without touching the tube. The drive mechanism consisted of two pulleys, a counter weight.

Jan 1, 1969

By Robert J. Hite, Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table 1), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term potash originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first US patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 27.5 Mt K20 produced in the world in 1980 (Searls, 1981) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K20, a unit of measure which is neither a natural nor synthetic compound of potassium (1.0% K is equivalent to 1.2046% K2O). Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and metamorphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such deposits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of seawater or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in Table 1. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971). The structural basins within which marine evaporites occur are of two main types: (a) cratonic basins formed by broad epirogenic movements (for example, the Michigan Basin of the midwestern United States and the Permian Zechstein Basin of eastern Europe), and (b) grabens, commonly related to continental

Jan 1, 1983

Discussion of the paper of WALTHER MATHESIUS, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 539 to 555. JOSEPH W. RICHARDS, So. Bethlehem, Pa.-This paper answers. partly the difficult questions which have come up as to why it is not economical to use higher blast temperatures in the smelting of Mesaba ores, such as the high temperatures used in European practices, and the answer is very plain that the ores will not stand the higher temperature. But the paper does not go into detail as to what special difficulties were found with the higher temperature of blast, and I would ask the author to kindly specify them. W. A. FORBES, New York, N. Y.-A large part of the troubles that furnace men experienced in using high-blast heats in smelting Mesaba ores in the early days of using Mesaba ores, was clue to the attempt to use these soft ores on furnaces having the same lines as the furnaces used in smelting the hard Old Range ores. As the result of observation and study, the dimensions of the lower part of the blast furnaces have been changed and the difficulties of the blast-furnace men in operating with a large percentage of Mesaba ore and high-blast temperatures have been largely overcome. The changes I refer to in particular are: (1) steepening the angle of the bosh; (2), decreasing the height of the bosh; (3) increasing the diameter of the hearth. JOSEPH W. RICHARDS.-Mr. Forbes's answer is quite satisfactory, and the moral which it points is that when the furnace is run with a higher temperature in the smelting zone, the furnace lines which were adapted for the lower temperatures are not necessarily those best suited for the higher hearth temperatures. If. enriched blast were used in a furnace, and higher temperatures run, it would be found necessary to further modify the lines of the furnace to meet the new conditions and to get the maximum output with economy. J. E. JOHNSON, JR., New York, N. Y.-It seems to me this is one of the few papers which could well have been a little longer. The data which Mr. Mathesius has given us, I think should be considered in connection with the paper which Mr. Brassert read before the American Iron and Steel Institute last spring, in which he described how they had obtained remarkable results with furnaces with steep but very short boshes; the angles have been raised to 80°, and the boshes made so short that they no longer appear as a conspicuous part of the shape of the furnace.

Jan 5, 1915

By AIME AIME

ON April 7 the twentieth national Open-hearth Conference of the A.I.M.E. will be held in Birming¬ham, Ala., in conjunction with a meeting of the Committee on Blast Furnaces and Raw Materials. At least 300 engineers and operators are expected to attend. Birmingham, the industrial city and iron, and steel center of the South, has been called the "Magic City." Men actively engaged in business in Birmingham today have seen practically every building in the business district erected, have witnessed the establishment of every existing industry, and have hunted birds cm the site now one of the busiest corners of the business district. Incorporated as a town in 1871, the city today has a population of more than 380,000 in its metropolitan area. It is

Jan 1, 1937

By B. C. Allen, R. I. Jaffee, D. J. Maykuth

Wrought unalloyed iodide chromium, containing 39 to 95 ppm total interstitials, has a tensile transition temperature of —15°C. Re crystallizing at 1100°C causes the transition to rise to 90° to 390°C, depending on the purity, grain size, and cooling rate after annealing. At about the 100 ppm level, individual additions of carbon or nitrogen raise the transition of both wrought and recrystallized chromium by as much as 210°C, while oxygen has a lesser effect, and sulfur essentially no effect. High transitzon temperatures are exhibited by recrystallized and quenched chromium, and appear to be associated with the amount and distribution of inter-stitials. The latter cm be either in solid solution or in the form of precipitates within the grains or at the grain boundaries. Quench hardening in chromium is primarily caused by nitrogen. The hardness, re crystallization, and grain growth behavior of chromium with and without impurity additions were also investigated. BECAUSE of low density and good oxidation resistance, chromium-base alloys are potentially useful for elevated-temperature applications. The main deterrent to the use of chromium in structural applications is its lack of low-temperature ductility, especially in the recrystallized condition. Accumulated evidence has shown that the ductility of chromium is sensitive to purity. The objective of the current study was to determine the effect of common nonmetallic impurities on the tensile properties of high purity chromium. The separate effects of carbon, oxygen, nitrogen, and sulfur additions on the ductile-to-brittle transition were evaluated for wrought and recrystallized material after various cooling rates. EXPERIMENTAL WORK Unalloyed iodide chromium and seven impurity alloys containing individual carbon, oxygen, nitrogen, or sulfur additions were prepared in rod form. Nominal additions were 100 ppm C, N, and S, and 100 to 500 ppm O. The additions were about a factor of ten greater than the residual amounts in the unalloyed material. The seven alloys and two unalloyed compositions were consolidated into four-pound ingots by conventional consumable arc melting of pressed and welded electrodes under 0.5 atm of helium. Impurity additions were made to the electrode in the form of crushed master alloys. The impurity alloys were double melted to improve homogeneity. The ingots were broken down by extrusion at 1200°C in evacuated steel cans at a reduction ratio of 18 :1, using a molten borosilicate glass lubricant and a ram speed of 80 in. per min. The cans were removed by acid pickling, and the chromium core ground free of surface undulations. Cut lengths were sheathed in mild steel and swaged at 900°C until the core was about 1/4 in. in diam. Two additional 15-lb ingots of unalloyed chromium (ICr-3, ICr-4) were prepared by arc melting and broken down by 26:1 extrusion at 1250°C without a steel can. The billet was lubricated and protected from contamination by a coating of molten glass. The resulting extrusion was then sheath swaged as described previously. Representative chemical analyses of each of the materials, after removal of a 10-mil surface layer

Jan 1, 1963

By Benjamin N. Webber

The peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guana-caste, which is the northern. of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guay-jiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. Physiography In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active; (2) the Atlantic lowlands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low- lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from 0 to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. History and Production The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1949

By Benjamin N. Webber

The peninsula of Nicoya contains virtually all of the known manganese deposits of Costa Rica. These are south and west of the Tempisque River, which flows across the peninsula near its juncture with the mainland. This peninsula forms the westernmost part of the province of Guana-caste, which is the northern. of the two Pacific Coast provinces of Costa Rica. The larger villages are connected by ox-cart roads and trails. The area may be covered on horseback without difficulty except during the rainy season, when rivers are in flood and difficult to ford. This is particularly true of the Rio Seco-Guay-jiniquil area, where there are no inhabitants and few open trails through the tropical jungle. Santa Cruz and Sardinal are served by the Taca Airlines, two planes a week from San Jose and Puntarenas. The port of Puntarenas has excellent loading facilities but none are available nearer the manganese districts; there ore must be lightered to vessels standing offshore. Physiography In Costa Rica there are three physiographic divisions: (I) the central plateau (Mesa Central), a somewhat dissected lava platform upon which are superimposed volcanic peaks, some of which are still active; (2) the Atlantic lowlands and (3) the Pacific lowlands. The peninsula of Nicoya and the larger part of the province of Guanacaste lie within the Pacific low- lands. The term "lowland" indicates relation to the central plateau, as the peninsula of Nicoya is largely mountainous. The mountains of Nicoya form the southern extremity of a range of low hills, which are almost continuous along the Costa Rican coast to the Nicaraguan border. The coast line shows evidence of subsidence. The Gulf of Nicoya obviously is the drowned valley of the Tempisque River. The west coast of Nicoya shows many rocks, shoals, bays, inlets and small islands as evidence of a sea encroachment. The altitude of the manganese deposits ranges from 0 to 800 ft. Topography is of the mature type of wide valleys and low hills, often with abrupt slopes. The climate is tropical and humid; rainfall of 125 in. falls largely between Sept. I and Jan. I. Vegetation often is very dense, the Rio Seco-Guayjiniquil area being truly tropical jungle, containing many hardwoods. History and Production The production of manganese ore in Costa Rica apparently dates from the first World War. It reached a peak of about 10,000 tons in the year 1919, then declined rapidly. Evidence of this period of prospecting has rotted away or been swallowed by the jungle. The war now in progress apparently revived the interest in Costa Rican manganese and has encouraged further prospecting. Deposits long known have been redenounced and trails have been cut through the jungle to them. Many new deposits have been discovered in the last

Jan 1, 1949

By Paul F. Kerr

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 t- 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre-Cambrian.

Jan 5, 1953

By G. R. Speich

The distribution of carbon and the type of substructure in iron-carbon martensites containing 0.02 to 0.57pct C has been studied in the as-quenched condition and after tempering at 25" to 700°C by using electrical resistivity, internal friction, hardness, and light and electron microscope techniques. in marten-sites containing less than 0.2 pct C, almost 90 pct of the carbon segregates to dislocations and to lath boundaries during quenching; in martensites containing greater than 0.20 pct C, appreciable amounts of carbon enter normal interstitial positions located far from defects. Tempering martensites with carbon contents below 0.20 pct at temperatures below 150°C results in additional carbon segregation to dislocations and to lath boundaries but no carbide precipitation whereas -carbide precipitation occurs in martensites with carbon contents exceeding 0.2 pct. Above 150°C, a rod-shaped carbide (either Fe3C or Hagg) is precipitated in all cases. At 400°C, spheroidal Fe3C precipitates at lath boundaries and at former aus-tenite grain boundaries. At 400" to 600"C, recovery of the martensite defect structure occurs. At 600" to 700°C, recrystallization of the martensite and Ost-waW ripening of the Fe3C occur. The effects of the carbon segregation that occurs during quenching and the subsequent substructural changes that occur during tempering on martensite tetragonality, hardness, and precipitation behavior are discussed. A mathematical analysis of carbon segregation during quenching is presented. RECENT studies of the strength of low-carbon martensitel-4 emphasize the importance of carbon segregation to the martensite lath boundaries and to the dislocations contained between them during quenching. Unfortunately, very few studies of the tempering of low-carbon martensites have been conducted, so the exact nature of this segregation is poorly understood. In fact, most early tempering studies5,6 were restricted to carbon contents greater than 0.20 pct. Moreover, these studies did not determine the amount of carbon segregated to the martensite substructure during quenching so that the initial state of the martensite was not established. Aborn7 studied the precipitation of carbide in low-carbon martensite during quenching but did not establish whether carbon segregation occurs prior to carbide precipitation, nor did he study the subsequent tempering sequence in detail. In the present work we have used electrical resistance and internal friction measurements, supplemented by electron transmission microscopy to establish the carbon distribution in as-quenched specimens. Specimens thin enough to avoid carbide precipitation (but not carbon segregation) were employed. The redistribution of carbon on subsequent tempering below 250°C was followed by measurements of elec- trical resistance. Additional studies were made on specimens tempered at 250" to 700°C to elucidate the overall tempering behavior of low-carbon martensites, including the formation of cementite and recrystalli-zation of the martensite. EXPERIMENTAL PROCEDURE Eight iron-carbon alloys with 0.026, 0.057, 0.097, 0.18, 0.20, 0.29, 0.39, and 0.57 wt pct C were prepared as 8-lb ingots by vacuum melting. Typical impurities in wt ppm were 40 Si, 20 Mn, 30 S, 10 P, and 10 N. These alloys were hot rolled to 3 in. plate at 1095°C) (2000°F). The hot-rolled plates were surface ground to remove scale and the decarburized layer, then cold rolled to 0.010 in. sheet. Specimens cut from the sheet were austenitized for 30 min at 1000°C (1830°F) in a vacuum tube furnace in which the pressure did not exceed 2 x 10-3 torr. Chemical analysis of specimens after austenitization indicated no decarburization at this pressure. Immediately before quenching, the furnace was filled with prepurified helium. The specimen was then pushed rapidly through an aluminum foil gasket, which sealed the bottom of the furnace, into an iced-brine bath (10 pct NaC1, 2 pct NaOH). The quenching rate at the M, temperature is about 104'c per sec for 0.010 in thick specimens, as calculated from Newton's law of heat flow2 using a heat transfer coefficient of 25 ft-'. This quenching rate is sufficiently high so that all the alloys transformed completely to martensite throughout the entire 0.010 in thickness and no carbide precipitation occurred in the martensite. All specimens were immediately transferred to liquid nitrogen after quenching and stored there until needed. Tempering below 250°C (480°F) was done in silicone oil baths thermostatically controlled to *;"C. Tempering above 250°C was done in circulating air furnaces or lead pots with the specimens contained in evacuated silica capsules. Electrical resistance was determined by measurement of the potential drop across both a standard resistance and the specimen, connected in series. All resistance measurements were made in liquid nitrogen (77K, -196°C) to minimize thermal scattering of electrons and thus maximize the contribution of impurity scattering to the resistance. Specimen dimensions were 5.10 by 0.19 by 0.025 cm. Although the precision in the electrical resistance measurements was +0.1 pct, the electrical resistivities could only be measured with an accuracy of +5 pct because of uncertainty in the specimen dimensions. Internal friction measurements were performed in an inverted pendulum apparatus at vibration frequencies of either 1.9 or 66 Hz. The specimen dimensions were 5.10 by 0.375 by 0.025 cm. Hardness measurements were made with a Leitz-Wetzlar microhardness machine with loads of 100 g. Specimens were examined by light microscopy after etching in 2 pct Nital and by electron transmission microscopy after preparation of thin sections by electrolytic thinning in a chromic-acetic acid solution.

Jan 1, 1970

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By J. E. Tobey

THERE are a lot of good things about this great industry of ours. Let us stop commiserating and consider some of the things that are right in this business. Coal is number one in the basic material industries. Our civilization owes more to it than to any other basic commodity. We are literally immersed in the benefactions of coal. In cur man-made world it is indispensable and we are constantly surrounded by objects, materials, and services which owe their existence to coal. Practically all the important materials, such as iron, steel, brick, cement, lime, rubber, glass, cotton, and wood have felt its magic touch.

Jan 1, 1939

By C. S. Simons

The conversion of a successful research and development effort into a money-making business venture requires careful attention. Problems of a business nature, such as market size, product selling price, raw materials and fuel availability and cost, financing factors, local and national taxes, licensing arrangements, etc. must, of course, be considered and resolved. In addition, the technical questions involving the scale-up of pilot plant or laboratory results to the full-scale plant must be resolved in order to avoid the financial disaster that attends a major delay in the startup of a commercial facility. The very difficult and demanding task of providing the interface between the research laboratory and the profitable metals processing plant will be discussed with examples from the author's extensive experience. After I had accepted the invitation to present a paper on the above subject of the interface between R & D and production operations, I began to give some serious thought to the subject. The program chairman had told me, in conveying the invitation, that what the committee had in mind was a discussion of positive and negative, forces in that interface, based on "gray-hair" experience. I am, therefore, at least physically qualified! My first reaction was one of mild shock; after over twenty years in the direct pursuit of the conversion of research and development findings into plant operations, I had never tried to sort out my , experience into a formal system of DO'S and DON'TS for the edification of posterity. However, after a little further reflection, I realized that this carries no stigma. No one has been able to formulate such a set of rules, and it is not really very likely to be done. Particularly if they are to be practical. I shall therefore settle for a more modest goal; I will simply discuss the factors that I have come to believe are the most critical in insuring that re- search and development results are converted into successful operation.

Jan 1, 1973

By E. Rudy, St. Windisch

The only complete phase diagram investigation of the Ti-W system is by Maykuth and coworkers,&apos; Fig. 1. Although previous work by Gonser2 indicated complete miscibility, later investigations3°5 essentially confirmed the diagram depicted in Fig. 1. The present study was undertaken because preliminary results on metal-rich ternary Ti-W-C alloys indicated complete solid solubility between 0 titanium and tungsten at temperatures above 1300°C—in contradiction to the presently accepted diagram. The powdered elements, as well as crystal bar titanium and tungsten sheet, were used in the preparation of the experimental alloys. The iodide titanium, obtained from Foote Mineral Co., Exton, Pa., had a total impurity content of less than 410 ppm, of which 150 ppm were interstitials (H, O, N, C). The overall purity of the titanium powder (Var-Lac-Oid Chemical Co., New York) was better than 99.7 pct. Major contaminants, in ppm, included: 0, 800; N, 10; H, 1500; Fe + Co + Ni + Cu + Zn, 50; C1, 200. The measured lattice parameters of the titanium were a = 2.94A and c = 4.68,A. The tungsten sheet and the tungsten powder (Wah Chang Corp., Albany, Ore.) contained the following impurities (in ppm, values in parentheses refer to the sheet tungsten): Mo, 50 (70); 0, 140 (110); Fe, 20 (60); Ni, 20 (not determined); N, 110 (not determined); sum of other impurities, <60 (<100). Samples from the iodide titanium bar stock and from tungsten sheet were prepared by repeated melting of the chipped materials in a nonconsumable electrode arc furnace under high-purity helium. The melted alloys were heavily cored, and homogeneity of the alloys could only be achieved after prolonged heat treatments at subsolidus temperatures. The majority of the alloys were therefore prepared by cold compacting the well-mixed powders in steel dies and pre-homogenizing the compacts for 6 hr at 1300°C in a tungsten-element furnace. The vacuum was better than 10"6 Torr, but for additional protection the sample container was wrapped in zirconium foil. Both preparation methods led to identical results. The measurements of the solidus temperatures were carried oat in the Pirani-type furnace described in a previous paper.6 Incipient melting in alloys containing between 20 and 90 at. pct W was rather difficult to detect visually, and therefore a photoelectric transducer system7 was employed to indicate the phase change. For the investigation of the solid-state equilibria, the specimens were first homogenized for 2 hr at slightly subsolidus temperatures in the Pirani fur- nace and then reequilibrated at, and rapidly cooled (-100°C per sec) from, the selected equilibrium temperatures. After the runs, the alloys were analyzed microscopically and by X-ray diffraction. With the exception of spot checks for oxygen and nitrogen in processed alloys, no other chemical analyses were performed. However, as the weight changes of the alloys during processing were within 0.05 pct and the lattice parameters of indeqendently prepared alloy series agreed within 0.0015A, it is reasonable to assume that no significant concentration shifts with respect to the nominal compositions had occurred. The measured solidus temperatures, shown together with literature data in Fig. 2, ascend smoothly from

Jan 1, 1969

By Frederick Becket

DOCTOR Albert Sauveur, distinguished scientist and Honorary Mem-ber of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur&apos;s prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future respon-sibilities with which it is accompanied. Several of the previous lecturers had the good fortune to attend the classes of Professor Howe and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe&apos;s book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world&apos;s pioneers in metallography, I was curious a few days ago to learn the nature of Howe&apos;s early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence. of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it.

Jan 1, 1938

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines of less than 500 h.p. cannot now he included in the category of large gas-engines, and therefore I have not considered engines under that power. Table I.—-" Oechelhauser " Type Gas-Engines. Built or Building by William Beardmore Co., Limited, Glasgow Indicated ! Engines. Horse-Power Type. Nature of Work. Gas Used. 6 2,500 Twin cylinder. Dynamo. Producer. 1 in Single cylinder. Rolling-mill. Producer. 4 1,250 Twin cylinder. Dynamo. Producer. 2 1,250 Single cylinder. Dynamo. Producer. 4 625 Single cylinder. Dynamo. Producer. 1 625 Single cylinder. Rolling-mill. Producer. 1 625 Single cylinder. Air compressor. Producer. 2 500 Single cylinder. Air compressor. Producer. 7 500 Single cylinder. Cement-mill driving Producer. Total, 28 engines ; 32,600 indicated horse-power. * Presented at the Joint Meeting of the Iron and Steel Institute and the American Institute of Mining Engineers, London, July, 1906, and here published under a mutual agreement between the Councils of the two Institutes.

Jan 1, 1907

By Elton A. Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11. mile bus ride up Railroad Creek to Holden. A11 freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting. Ore is broken by long-hole blasting using the Noranda system which has been modified to meet local conditions. Until recently, blastholes have been drilled by diamond drills. Now a partial substitution of percussion drill holes, drilled with tungsten carbide insert bits, is being made. Geology The ore body occurs as a replacement deposit in a highly metamorphosed series of sedimentary rocks, mainly gneiss and schists, in a shear zone several hundred feet in width and of undetermined length. Commercial ore has been found in mineable widths of 25 to 100 ft for approximately 2500 ft along its strike. The commercial minerals are chalcopyrite, sphalerite, and gold. During the period of mineralization considerable silicifica-tion took place giving the ore an abrasive drilling characteristic. Following the period of mineralization, numerous dikes were introduced into the ore body. The earlier ones were of granite composition having a width of a few inches up to 80 ft. These were followed by much younger, fine grained basic dikes which usually do not exceed 2 ft in width. Development of Percussion Blasthole Drilling Equipment Test work with the 1½-in. tungsten carbide bit was carried on in development headings for several months early in 1947. The short life of the bits, because of gauge loss caused by the abrasive nature of the rock, prevented its adoption for this use. However fast drilling speed and ability to drill a long uniform hole suggested its use for drilling blastholes in competition with diamond drills as diamond costs were steadily increasing and exper-ienced drillers were difficult to obtain. The 1½-in. bit was the largest available at the time initial test work was started with sectional steel. The 1½-in. hole limited the diameter of the steel thread and coupling which could be used. Type F couplings were first used but because of the small thread section excessive breakage of the steel was experienced. Type H couplings were tried next. In order to use this coupling which is 15/8 in. in outside diameter, it was reduced to 1 3/8 in. giving 1/8 in. clearance between the coupling and the hole. Rod breakage at the thread was substantially reduced but some coupling breakage was experienced, however the overall performance was considered satisfactory (see Fig 1 for illustration of coupling and thread). Early test work with the 1½ in. bit indicated machines of piston diameters larger than 255 in. would cause inserts to loosen or break. It was found however that the additional weight of the sectional steel cushioned the blow enough to prevent bit failures when 3-in. Leyners were used. Rods used with the 1½-in. bits were 7/8 in. q. o. for sectional steel and 1 in. q. o. for all chuck pieces. In May 1948, 2-in. tungsten carbide bits became available and test work was immediately started. The 2-in. hole approximated the AX (1 15/16 in.) diamond drill hole which was being used exclusively for blastholes and permitted their substitution for diamond drill holes in a ring without alteration of pattern, burden, or explosives. The 2-in. bit also gave room in the hole for larger couplings and permitted the use of heavier rods and 3½-in. machines, increasing the

Jan 1, 1950

By Frank Robertson Van Horn

In June, 1911, the writer spent a few days in studying the economic geology of the vicinity of Park City. During this rather hurried visit a number of specimens of ore were collected, which have since been examind. The results of these investigations show that bournonite (PbCu-SbSa) is present in the ores in greater or less quantity. This fact has never before been reported, as far as can be learned. The failure to recognize this mineral is due to its similarity to tetrahedrite, with which it has probably been confused during a long period of years. Jamesonite (Pb2sb2s6) has been reported from the region in a rather doubtful manner, but the writer has seen it in notable amounts from several mines, and can offer the first analysis of this mineral from the district. Calamine (HzZn2SiO5) was found at one mine and has never been ecognized and reported from the district. Geogbaphy and Geology Park City, Utah, is located at an elevation of about 7,000 ft. above sea level on the eastern slope of the Wasatch mountains. It is situated approximately 25 miles southeast of Salt Lake City. &apos; The geology and ore deposits have been described in detail by Bout well and Woolsey.&apos; The mines visited are situated south-southeast from the town. The Silver King Coalition mine is located in Woodside gulch about 1 mile southeast of Park City, at an altitude of about 8,100 ft. The other mines visited were the Daly West and Quincy, which are in Empire canyon about 2 miles sontheast of the town, at elevations of 8,300 to 8,500 ft. respectively. The Daly Judge tunnel goes into the mountain from Empire canyon about 1 mile south of the city, at an altitude of 7,700ft.

Jan 1, 1915

By F. H. Wilson, E. W. Palmer

The solid solubility of iron in 2 to 10 pct cupro-nickels increases with temperature and nickel content. Property changes accompanying various heat treatments indicate typical precipitation hardening behavior. Iron content also affects softening temperature and sub-scale formation. These factors, as well as impingement corrosion resistance, influence the optimum iron content of commercial alloys. FOR many years Cu-Ni alloys have been used extensively in the form of tubes, pipes, and plates for the construction of salt-water lines and surface condensers on shipboard and in tidewater power stations. The 30 pct Ni alloy has been considered more resistant to rapidly flowing sea water than alloys of lower nickel content, and has been standard on ships of the U. S. Navy. Some ten years ago, the still better corrosion resistance obtained by modifying the 30 pct Ni alloy with approximately 0.5 pct Fe was recognized, and the iron-bearing alloy rapidly superseded the plain alloy as the standard material for severe service. In 1945, Tracy and Hungerford1 published a study of the effect of iron on the corrosion of various cupro-nickels in sea-salt solutions, and their data indicated that the 10 pct Ni alloy containing about 0.75 pct Fe was equivalent to the 30 pct Ni alloy containing 0.5 pct Fe. This was confirmed by LaQue in discussion of the above paper, and by results in an experimental condenser set up at the Kure Beach marine test station of The International Nickel Co., reported by Freeman and Tracy.&apos; The 10 pct Ni iron-bearing alloy is now being very widely used in applications where the 30 pct Ni iron-bearing alloy was formerly considered standard. While this "substitution" has undoubtedly been stimulated by the present extreme shortage of nickel, it must be emphasized that it involves no loss of service performance, and would have occurred anyway in the course of time, for economic reasons. In view of the increasing use of the 10 pct alloy, it seems desirable to make generally available the results of several investigations of Cu-Ni-Fe alloys carried out in the Metallurgical Research Laboratory of The American Brass Co. in recent years. The present paper, deals with the constitution of these alloys in the copper-rich corner of the system, and with the variations in hardness and tensile properties resulting from the heat treatment of alloys containing various amounts of iron. Most of this work is concerned with alloys containing 10 pct Ni. With over about 0.75 pct fe, the 10 pct Ni alloy is suscep- Alloys Several series of cupro-nickel alloys containing iron were used in these investigations. Most of them were prepared in the laboratory, but two samples of commercially fabricated alloys were included. Series A—Nominally 2 and 5 pct Ni, each with 0 to 1.5 pct Fe. Series B—Nominally 10 pct Ni with 0.1 to 0.4 pct Fe. Series C—Nominally 1.0 pct Ni with 0 to 2 pct Fe. Series D—Nominally 10 pct Ni with 3 to 5 pct Fe. Series E—Nominally 10 pct Ni with 1 and 1.5 pct Fe.

Jan 1, 1953

By P. Marier, T. R. Ingraham

When anhydrous cupric sulfate is heated in a stream of nonreactive gas, cupric oxysulfate is formed. When this reaction is complete, the cupric oxysulfate then decomposes to cupric oxide, which is the normal end product of reaction. The kinetics of each of these reactions has been studied using pellets prepared from finely divided cupric sulfate and from finely divided cupric oxysulfate. In each case, the reactant-product interface within the pellet is well-defined, and by normalizing the decrease in inter facial area with the weight fraction of the pellet decomposed it has been shown that the interface migrates into the pellet at a uniform rate at constant temperature. The activation energy estirnated for the decomposition of cupric sulfate is 57 ± 7 kcal per mole and that for cupric oxysulfate is 67 ± 8 kcal per mole. The rate of interfacial reaction is flow-sensitive, increasing with increasing flow of a sweep gas in the range from 50 to 2000 cu cm per min. The rate of decomposition is retarded by sulphur trioxide in the sweep gas. The relationship between sulfur trioxide Partial pressure and rate is consistent with the Langmuir Adsorption Isotherm governing the retention of sulfur trioxide in the interfacial layer. MOST of the work reported on the thermal decomposition of cupric sulfate and of cupric oxysulfate is related to the thermodynamics of the individual decompositions.&apos;-4 No information is available on the rates of the individual reactions, on their activation energies, or on the effects of gas flow or of partial pressure of sulfur trioxide on the reaction rates. Some dubious conclusions based on relative reaction rates have been drawn from studies on the oxidation of sulfides. For example, on the basis of the products observed in a quenched system, it has been suggested5" that, when copper sulfide is roasted, the cupric oxide which is formed arises from the decomposition of either cupric sulfate or cupric oxysulfate. This is very difficult to reconcile with the thermodynamics of the C-S-O System,3 which support the probability that both cuprous oxide and cupric oxide precede cupric oxysulfate and cupric sulfate in the sequence of products formed during the oxidation of cuprous sulfide. In this paper the individual sulfate decomposition reactions will be examined and suggestions will be advanced for the mechanism of reaction. This will be based on the effects on reaction rate of changes in interfacial area, flow rate, and back-pressure of sulfur trioxide. EXPERIMENTAL Materials. The copper source material used in all experiments was Fisher Certified Reagent Grade anhydrous cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared by roasting cupric sulfate for 48 hr, with frequent rabbling, in an open tray in a muffle furnace maintained at 725°C. At this temperature, cupric sulfate develops about 0.16 atm pressure of combined sulfur trioxide, sulfur dioxide, and oxygen. Cupric oxysulfate develops only about 0.05 atm pressure, and is stable until

Jan 1, 1965