Search Documents

By David B. Reger

The year 1935 was mostly quiet in West Virginia, and devoted to routine drilling in old pools and extensions. A notable exception to this general rule, however, was the further development and proving of a field of gas discovered in 1930 in the deep Oriskany sand (L. Dev.) in Kanawha County, as later discussed. No new pools of oil were found and little or no attempt was made to search for them. No new pools of gas were recorded but various extensions of old pools were made. There were no new pipe line extensions of consequence, either for oil or gas. Operating technology was much the same as in recent years, there having been some further advances in repressuring oil wells and in the use of acid for treating small wells in calcareous formations, and some change in the technique of shooting gas wells. Financially, there has been a full market for all crude oil produced and a fair market for gas. There have been occasional transfers of producing oil or gas properties, mainly between established companies. Most of the attempts made to finance mergers and new developments have failed largely because of difficulties encountered under the Federal securities act. This situation has prevented the normal turnover of properties by small operators who frequently desire to sell partly developed interests and then step out into new ventures. New Development In 1935 the State issued 569 permits for drilling and records the same number of completions. One trade journal records 533 completions and another 483. A running record kept by the writer accounts for 713 completions, with 156 oil wells, 417 gas wells and 140 dry holes (Table 3). Some of these completions may be old wells drilled to deeper sands. Some, apparently, have been drilled without legal permit. Extensions of Producing Areas Ritchie County has again led all others in new drilling, with 137 completions as compared to 74 in Calhoun and 61 in Cabell. This Ritchie County drilling was done mainly to extend or further develop old pools

Jan 1, 1936

By David B. Reger

The year 1935 was mostly quiet in West Virginia, and devoted to routine drilling in old pools and extensions. A notable exception to this general rule, however, was the further development and proving of a field of gas discovered in 1930 in the deep Oriskany sand (L. Dev.) in Kanawha County, as later discussed. No new pools of oil were found and little or no attempt was made to search for them. No new pools of gas were recorded but various extensions of old pools were made. There were no new pipe line extensions of consequence, either for oil or gas. Operating technology was much the same as in recent years, there having been some further advances in repressuring oil wells and in the use of acid for treating small wells in calcareous formations, and some change in the technique of shooting gas wells. Financially, there has been a full market for all crude oil produced and a fair market for gas. There have been occasional transfers of producing oil or gas properties, mainly between established companies. Most of the attempts made to finance mergers and new developments have failed largely because of difficulties encountered under the Federal securities act. This situation has prevented the normal turnover of properties by small operators who frequently desire to sell partly developed interests and then step out into new ventures. New Development In 1935 the State issued 569 permits for drilling and records the same number of completions. One trade journal records 533 completions and another 483. A running record kept by the writer accounts for 713 completions, with 156 oil wells, 417 gas wells and 140 dry holes (Table 3). Some of these completions may be old wells drilled to deeper sands. Some, apparently, have been drilled without legal permit. Extensions of Producing Areas Ritchie County has again led all others in new drilling, with 137 completions as compared to 74 in Calhoun and 61 in Cabell. This Ritchie County drilling was done mainly to extend or further develop old pools

Jan 1, 1936

By AIME AIME

I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability.

Jan 1, 1967

By William M. Bowron

Thirty years ago, when I stood on the cliff of red fossil iron-ore, on Red mountain, Jefferson county, Ala., I asked what were the geological relations of this remarkable deposit. In reply I was told that it was a limestone, colored and saturated by some unknown but wholly external influences, and that at a reasonable distance from the surface the color would disappear. I could find no satisfactory explanation, either of the nature of this wonderful external permeating influence, or of the cause of such a ferrous impregnation selecting this one particular bed of limestone, to the exclusion of the higher and lower beds of the same material which are not even stained. I. The Present Theory. Referring to this subject, Dana says :' "The clays, clayey sandstones and limestones of the Clinton epoch, through New York and the Appalachians, show that the mud-flats and sand-banks, and hence the shallow seas of the coast region, still continued.... The beds of argillaceous iron-ore, which spread so widely through New York and some of the other States, west and south, could not have been formed in an open sea; for clayey iron-deposits do not accumulate under such circumstances. They are proof of extensive marshes, and, therefore, of land near the sea-level. The fragments of crinoids and shells found in these beds are evidence that they were, in part at least, salt-water marshes, and that the tides sometimes reached them." At first, this explanation seemed satisfactory, but the more I studied the ore the less satisfying the explanation became. 1. In the ore itself, I found associated with the small particles of rounded matter (now consisting of iron oxide in which organic structure, if ever present, has become lost, though the

Jan 1, 1906

By Horace H. Emerich

PrePatory Note.—The first part of this paper was sent to me by Mr. Emrich nearly nine months ago; and I held it, waiting for the second part, which he had promised to forward soon, so that I might submit the whole to some of his former professional associates, and advise him of their criticisms and suggestions before off'ering his work to the Institute. But, five days before the second part reached me, I received by telegraph the news of Mr. Emrich's sudden death. The paper has therefore not had the benefit of such a revision by the author as might have made it ill some respects clearer and more cornplete. Nevertheless, I believe that experts in the branch of metallurgy with which it deals will find it both original and suggestive.—A. Eilers. I. Partial ReFining iN the ANode-Furnace. During my connection with one of the large New Jersey copper-refineries, and probably before that period, from 15 to 30 per cent. of the copper-bullion received was the very foul, leady blister-copper produced from lead blast-furuace matte. It had been customary to mix a small part of this blister with each charge of purer pig-copper, in the effort to dilute it as much as possible before casting into anodes; but tank-house conditions were such that I was led to try making entire furnace-charges of this blister, and refining it as much as possible in the furnace—afterwards casting to anodes and refining elec-trolytically, in tanks and solution separate from the main bulk of the purer copper. In making this experiment, notes were made, for several furnace-charges, of everything thought to have a bearing on the question, and some interesting facts were brought out, both in the furnace-working and afterwards in the tanks.

Jan 1, 1913

By J. F. Blandy

IN October last, I was call upon to examine a copper deposit in the South Mountain, near the Pennsylvania and Maryland boundary. The specimens shown me contained oxides and carbonates with native copper, and were similar to some that had been described to me some years ago as existing at the Luray Gap in Virginia. An examination of Rogers's Report on the Geology of Pennsylvania, led me to expect to see his so-called "Primal Formation," such as exists throughout the southeastern district of the State. I was therefore much surprised on arriving at the summit of the Western Maryland Railroad to find myself on familiar ground. Instead of the "Primal" as I had known it in Southeastern Pennsylvania, I soon decided that the rocks were identical with the "Lake Superior Copper Formation." My visit was unfortunately a short one, part of two days, and in that time I had to pass over a good many miles, but I saw sufficient to convince me that instead of the Lake Superior Copper Formation being a local geological feature, it would have to be considered as a widely extended series of rocks. I was unable to even approximately estimate the thickness either of the trap zone or other members, schists and slates, of the series. In an article on the Copper Range of Michigan, prepared by C. P. Williams and myself in 1862, and published, in vol. xxxiv of the American Journal of Arts and Sciences, we endeavored to divide that range into zones, according to the character of the traps. The limited nature of the explorations at that time made this work very imperfect. Subsequent explorations have confirmed my notes then

Jan 1, 1879

By J. F. Blandy

In October last, I was call upon to examine a copper deposit in the South Mountain, near the Pennsylvania and Maryland boundary. The specimens shown me contained oxides and carbonates with native copper, and were similar to some that had been described to me some years ago as existing at the Luray Gap in Virginia. An examination of Rogers's Report on the Geology of Pennsylvania, led me to expect to see his so-called "Primal Formation," such as exists throughout the southeastern district of the State. I was therefore much surprised on arriving at the summit of the Western Maryland Railroad to find myself on familiar ground. Instead of the "Primal" as I had known it in Southeastern Pennsylvania, I soon decided that the rocks were identical with the ('Lake Superior Copper Formation." My visit was unfortunately a short one, —part of two days, and in that time I had to pass over a good many miles,—but I saw sufficient to convince me that instead of the Lake Superior Copper Formation being a local geological feature, it would have to be considered as a widely extended series of rocks. I was unable to even approximately estimate the thickness either of the trap zone or other members, schists and slates, of the series. In an article on the Copper 'Range of Michigan, prepared by C. P. Williams and myself in 1862, and published. in vol. xxxiv of the American Journal of Arts and Sciences, we endeavored to divide that range into zones, according to the character of the traps. The limited nature of the explorations at that time made this work very imperfect. Subsequent explorations have confirmed my notes then

Jan 1, 1879

By E. E. White

I disagree with Mr. Brinsmade on serveral points, and I will discuss this remards under the same six topics which he has used.

Jan 1, 1915

By Bert S. Sandell

Much has been said and written about the various uses of die castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100" F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500" F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties. Alloys Investigated Two types of alloys were used in this investigation—zinc-base and aluminum-base alloys. Two alloys of each group were included. Those most generally employed in the industry at present were selected. Alloys A and B are of the same nominal composition, and correspond to A. S. T. M. alloy XXI, containing 4 per cent aluminum, 3 per cent copper, 0.1 per cent magnesium, and the balance zinc of 99.99 per cent

Jan 1, 1932

By ROBERT B. COONS

SELECTIVE SERVICE must meet three important demands for man power: (1) Activities concerned with production of war goods. (2) The armed forces. (3) Civilian activities and institutions the continuance of which are essential to maintaining the structure of our American democracy. In the above enumeration of demands I have placed everything, including most of our most prized possessions and activities, after the demand for men for war production and the armed forces. To establish an order between the latter two is difficult. For the time being, at least, the Selective Service policy is to make sure that we avoid the risk of "too little and too late." No soldier, sailor, or marine should be sent from these shores to risk his life without the assurance of having a gun, clothes, food, and medical supplies. Therefore, the premium is now being placed on man power for war production and in our process of selection no stone is left unturned to see that our agencies are fully informed of the needs of war production. Our procedures set up recourses for employers of war-production man power so that their activities need not be disrupted, at least not until they have had time to train replacements.

Jan 1, 1942

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for spectroscopically pure silver, and for o series of solid solutions of silver with cadmium, indium, and tin, using a Ke-type torsion pendulum apparatus. Some experiments have also been made to investigate the effect of nonmetallic impurity on grain boundary relaxation in silver. The effect of the alloying elements is to increase the grain boundary viscosity, and to raise the activation energy for grain boundary relaxation from 22,000 cal per mol for pure silver to 43,000 cal per mol for the solid solutions; the same value being obtained, within the limits of experimental error, for all the alloying elements and solute concentrations investigated. Results of the experiments show exactly the same trend as those obtained previously for a similar series of copper solid solutions. They are in agreement with the general theory of grain boundary relaxation developed by Zener and Ke, but do not seem to be in agreement with either of the mechanisms so far put forward to explain grain boundary slip. EXPERIMENTS described in this paper were made as part of an investigation into the effect of alloying elements in substitutional solid solution on grain boundary viscosity, measured by the internal friction method developed by Ke.&apos; The apparatus and experimental procedure have already been described.&apos; Preliminary work was done with spectro-scopically pure silver. Experimental Work Materials Used—All the materials were supplied in the form of % mm diam wire by Messrs. Johnson Matthey and Co. Ltd. The silver and all the alloying elements used were spectroscopically pure. Composition of the alloys is given in Table I. They were all melted and chill cast under the same conditions as the copper alloys. The ingots were rolled to 1/4 in. sq rod with intermediate annealing at 600°C in an atmosphere of cracked ammonia when necessary. These rods were then drawn to wire by standard procedure with intermediate bright anneals at suitable steps in the drawing operations. Specimens from the annealed wires were sectioned longitudinally. mechanically polished, and examined under the microscope. They were then etched and reexamined. Grain sizes were reasonably uniform for all wires, and no traces of a second constituent were observed. The wires were weighed before and after testing so as to measure any loss of the alloying element due to evaporation. The loss was less than the accuracy of measurement—< 0.1 pct of the total weight— for the Ag-In and Ag-Sn alloys, but appreciable loss of weight occurred in the case of the Ag-Cd alloys. The percentage loss is given in Table 11. X-ray diffraction photographs were taken of all thc wires after test to determine whether there was any marked preferred orientation. Results of the examination are given in Table 111. Experiments on Spectroscopically Pure Silver-— Experiments were made on specimens in which the grain diameter was small relative to that of the wire, and on one specimen in which the grains were grown by the usual strain-anneal method to extend across the full diameter of the wire. These large grained specimens will be referred to as single crystal specimens. The wires were annealed for 11/2 hr at 700°C, and experiments were made at two frequencies of vibration, 1.5 and 0.4 vibrations per sec. The variation of internal friction with temperature is shown in Fig. 1. Experiments on a second small grain specimen gave approximately the same results as for the first wire. It will be seen from Fig. 1 that the peak in the curve for the small grained wire, which is presum-

Jan 1, 1957

By C. G. Dunn, M. Sharp

HE orientations of 137 crystals of copper pro-T duced by secondary recrystallization in a cube texture matrix have recently been obtained. Although the crystals were not prepared for the purpose of determining a secondary recrystallization texture, the orientations obtained proved to be rather interesting, as they confirmed, in part, published results and also disclosed additional preferred orientations in the texture. The investigation of Dahl and Pawlek,&apos; Bowles and Boas,&apos; and Kronberg and Wilson3 showed respectively that the orientations of secondary grains growing in a cube texture matrix were related to those of the primary grains by a rotation of approximately 30" about [001], the rolling direction, by 30" about a <111> direction, and by either 22" or 38" about a <111> direction. Kronberg and Wilson also obtained a component of the texture similar to that of Dahl and Pawlek except the angle of rotation about [001] was 19". When the cube texture matrix was deformed a small amount, Kronberg and Wilson also obtained large grains on subsequent annealing corresponding to a rotation of 15" about the normal to the sheet, but these grains should not be classified as secondary recrystallization grains since they were produced subsequent to mechanical straining. The particular texture obtained, of course, depends on the composition of the copper and the processing schedule employed, since these factors markedly affect the primary recrystallization texture and the sharpness of any cube texture produced. In the present investigation, pieces of OFHC copper in the form of M in. round bars were cold forged to a thickness of about 0.40 in., annealed 1 hr at 350°C in an atmosphere of hydrogen, and cold rolled crosswise to a thickness of 0.200 in. These pieces were given a penultimate anneal of 1 hr at 350°C in hydrogen and a 90 pct cold-rolling reduction lengthwise to a thickness of 0.020 in. Indentations generally were put in one end of the as-cold-rolled strips to promote earlier formation of secondary grains.

Jan 1, 1953

By F. E. Lathe, G. A. Guess

This investigation was started with the idea of determining whether copper-nickel mattes might not have a lower flowing temperature than copper mattes, and thus perhaps aid in accounting for the difficulty so far experienced in attempts at pyritically smelting copper-nickel ores. We have used the term flowing temperature to avoid confusion with the usual melting temperature. The idea at first was that there might be a greater viscosity range in the one matte than in the other. In the early experiments it was in our minds to determine the relative fluidity of the mattes at a given temperature. Looking to this end we tried pouring equal quantities of matte at the same temperature down an inclined graphite slab, and comparing the distances traveled. Results from such experiments were not satisfactory. We next tried pouring equal quantities at the same temperature through a drilled hole in an Acheson graphite crucible, timing the flow with a stop watch, the whole operation being carried out in the muffle. The flowing temperatures of the mattes tried in this way appeared to be about the same, and there was no marked difference in their fluidity when well fused. Oxidation gave some trouble. These experiments finally led to the adoption of the following apparatus which we thought at the time was wholly original with us, but which we have since found was described by W. McA. Johnson.l The tray used was a slab of graphite 8 in. long, 2 in. wide and 1/4 in. thick. It had six holes, into each of which sat a cup of Acheson graphite. Centrally in the bottom of each cup was a vertically drilled hole 3/16 in. in diameter and 1/2 in. long. The mattes to be tested were put into the cups, in a solid piece. The cups were covered with inverted Battersea "A" cups. The tray was put into the muffle of a gas-fired furnace. Supports on each end held the tray about 2 in. from the floor of the muffle. Under

Jan 1, 1917

By Raymond D. Daniels, Frank E. Rizzo, James D. Gerber

ThIS discussion describes a method for the addition of small amounts of oxygen to columbium (niobium) in an accurate and reproducible manner. The method is based on the complete reduction by columbium of a carefully weighed amount of another metal oxide. The equilibrium Pq associated with Cb-CbO mixtures is extremely low, e.g., 10"25 atm at 100O°C, and the pressures over Cb-0 solutions are even lower. The equilibrium Pq associated with a given metal-metal oxide mixture can be easily obtained, with the aid of a Richardson-Jeffes chart.&apos; Although columbium should effectively reduce almost any metal-metal oxide combination, the proper choice of a metal-metal oxide system is complicated by the low rate of oxygen transport in the gas phase at low oxygen pressures and the difficulty in reducing any columbium suboxide formed during the reduction of the oxygen source material. Thermodynamically, oxide formation on columbium will be avoided so long as the oxygen partial pressure over the columbium is below the equilibrium pressure associated with the mixture Cb-CbO. The logical choice of a source for oxygen would appear to be a mixture of Cb-CbO, since oxide formation would be precluded by nucleation difficulty. But calculations using the kinetic theory of gasses indicate that, for a temperature of 900°C, the reaction would proceed too JAMES D. GERBER, formerly Research Assistant, University of Oklahoma, Norman, Okla., is Research Metallurgist, Air Force Weapons Test Laboratory, Kirtland Air Force Base, N. Mex. FRANK E. RIZZO, Junior Member AIME, formerly Assistant Professor of Metallurgy, University of Oklahoma, is Associate Professor of Metallurgy, University of Texas at El Paso, El Paso, Tex. RAYMOND D. DANIELS, Member AIME, Professor of Metallurgical Engineering, University of Oklahoma, is an NSF Fellow, Institute de MBtallurgie Structurale, Universite de euch:tel, Neuchitel, Switzerland. Manuscript submitted October 28, 1968. IMD

Jan 1, 1970

By T. D. Jones

MUCH the same story can be told for the lead industry for the year 1945 as for the three previous years. In response to inquiries as to new developments, invariably the answer has been, "No new developments-our men either too busy with the man-power problem or trying to get production out." Time and efforts of industry have been concentrated for the most part on war or readjustment problems. Now that V-E and V-1 day have passed, the lead industry can justly be proud of its record in World War II. As in previous wars, lead played an important role and one of its most spectacular uses was in the production of the atomic bomb. We read that the part lead played was rather obscure, but as a protective agent, lead played a most significant role. "Since the materials in the Pile Plant are intensely radioactive, all storage and handling must be done behind thick concrete walls or lead shields. The material is never seen and all operations are auto matically controlled by a foolproof remote control system especially designed for this purpose." (Chews. & Met., Sept. 1945.) When our armies invaded the European theater of war and made a landing on Normandy beach, gasoline and oil for the motive power were furnished through miles of armored lead pipe. This amaz-

Jan 1, 1946

By R. A. Pallanch

IN his recent paper, "The Controversial Art of Flotation," (Mining Technology, March, 1944) E. H. Rose states that "flotation is a science in so many variables that only art can blend them." This statement is apt. It contains meat. In other words, a valid scientific reason is behind every flotative effect. Some of these reasons we understand, but much the greater number of them still escape us. This does not prevent us from "going places," as familiarity and experience with the problems result in an increasingly intelligent and artful handling of these effects. Hypotheses are built up by the individuals concerned to explain certain happenings. Many of these hypotheses have to be abandoned when placed under the glaring scrutiny of actual trial. A few survive the severest of tests, come through unscathed, and are elevated to the rank of theories, something susceptible of certain chemical and physical explanation, under the conditions of the particular plant concerned. If these theories continue to hold water under all the variations existing in most milling plants, they gradually become accepted as facts in the minds of the plant operators. But-and here is a big BUT-these so-called facts may fall down completely in another plant working under an entirely different set of conditions. In other words, each plant tends gradually to build up its own facts, which may or may not be facts at another operation.

Jan 1, 1945

By John G. Baragwanath

THE September issue of the Engineering and Mining Journal carried an item regarding the Cercapuquio Mining Co. which was mentioned as a large producer of lead, zinc, and cadmium, situated near Huancayo, Peru. The paragraph caught my eye because I had not heard of the property in thirty years and I recollect all too well the circumstances of its accouchement. In 1916 1 was making my headquarters in the town of Huancayo, then the terminus of the Central Railway of Peru, and was examining mines and prospects in that general area for Cerro de Pasco. In the course of my work I became acquainted with an engaging and energetic "practical" miner named Balarin, a Dalmatian living in Huan¬cayo, and made numerous trips in his excellent company. One day Balarin came to the down-at-heels hostelry where I stopped and told me that a Cholo prospector, a character by the name of Jose, had just reached town and claimed to have made a discovery in a little known locality called Cercapuquio. Lead-silver, Balarin said, and showed me a sample of galena about the size of his fist. "Fine," I remarked. "When do we leave?"

Jan 1, 1947

By Hallan N. Marsh, Bruce H. Robinson

It is generally believed that the flowing of wells through tubing instead of casing results in the conservation of gas. It is further believed that use of tubing prolongs the flowing life of a well and results in greater ultimate recovery, provided either that there are no adjacent wells, or that any adjacent wells are similarly operated. Recent experience in the flowing of Buckbee zone wells at Santa Fe Springs has not only substantiated both of these beliefs but has led to the further conclusion that the use of tubing results in a greater cumulative flowing production, &apos; even in a highly competitive field like Santa Fe Springs, where the wells concerned are closely offset by wells of both the same and other companies flowing through casing. Further, gas-oil ratio has been so reduced that greater ultimate recovery can be expected. In the belief that such would be the case, the majority of the Buckbee zone wells of one company were brought in through tubing, but enough wells were flowed through casing to form the basis for a comparison. For the purpose of this comparison, wells with flow strings 2½ or 3-in. dia. are designated as tubed wells, while those having flow strings larger than 3-in. dia. are designated as untubed wells. Casing used was mostly of 5 ¾-in. dia., the remainder being of 4¾-in. dia. There were 15 tubed wells and 8 untubed wells and they were scattered over the field in such a way that neither group appears to have any distinct advantage as regards location. Locations of all wells involved in the comparison are shown on Fig. 1. All the Buckbee sand wells of the company are included in the average production curves, with the exception of eight that were unsatisfactory for reasons other than the method of flowing. Findings 1. Buckbee sand wells flowing through casing larger than 3 in. had an average maximum production rate of 4670 bbl. per day, while wells flowed through straight tubing or 3-in. casing had an average maximum production of only 3300 bbl. per day. (See Fig. 2.)

Jan 1, 1932

By T. Wasson

The same limitations&apos; that characterized 1931 existed in the old fields of Indiana and Illinois during 1932. Prices remained low. The average for the year for Illinois and southwestern Indiana was $1.032 as against $0.852 for 1931 and $1.616 for 1930. In September a curtailment of production of about 25 per cent became effective and was continued to the end of the year. There were no new discoveries and very little wildcatting was done. Considering the age of the wells, and the number still producing, there were few abandonments. The most outstanding thing about the old fields in these states is their long continued productivity. Illinois The fields along the southeast end of the LaSalle anticline had their peak of 33,686,000 bbl. in 1908. In 1932, with a 25 per cent restriction for 355 months, these fields produced 4,661,000 bb1.l There were 52 new completions (most of them in old territory) and of these 33 were dry, 8 were gas, and 11 were oil wells. The new oil wells had a total initial of 102 bbl., or an average of 9.3 bbl. per well. Nineteen of the new producers were in Crawford County. There were about 200 wells abandoned in the old southeast fields in 1932 as compared to 210 in 1931. The greatest number, 86, were in Lawrence County. To the end of 1932, the four major counties—Clark, Crawford, Lawrence and Wabash—had produced almost 394,000,000 bbl. from 92,160 acres. Better than one-half of this was produced in Lawrence County from 26,240 acres. The Dupo area of Sinclair County had no additions to production although four wells were drilled. On the Jacksonville structure in Morgan County, six gas wells with an average depth of 300 ft. were drilled to sands in the base of the Pennsylvanian. They produced an open-flow total initial of 2,000,000 cu. ft. This gas will be developed further to supply a local market.

Jan 1, 1933

By Kefton H. Teague

Olivine is a mineral containing a mixture of forsterite (Mg,SiO,) and fayalite (Fe,SiO,) in solid solution. The name "olivine" was first applied by Werner in 1790 (Hunter, 1941) because of the olive-green color of the mineral. Uses The principal use of olivine is in various foundry applications. Perhaps the largest tonnage is utilized as a special foundry sand for mold-making in brass, aluminum, and magnesium foundries (Schaller, 1957, 1958; Snyder, 1957). Olivine was first used as an industrial mineral in the early 1930s for a refractory material (Anon., 1970; Hunter, 1941). As a refractory raw material, olivine was first introduced in the United States as handcobbed, selected, shaped blocks of crude olivine. This use met with limited success. More recently, finely ground olivine blended with MgO and pressed into bricks, which are then fired, have found use in glass tank furnaces and open-hearth furnaces. Ramming or gunning mixes for basic furnace linings also utilize olivine. Olivine has been used in ladle linings with varied success. In Europe, substantial tonnages of olivine are utilized in refractory brick for night storage heaters (Anon., 1970). A limited amount of olivine has been used in the past as a fertilizer (magnesium source) and has been fused with rock phosphate to produce a magnesium phosphate as a plant food. The relatively high magnesia (MgO) content of olivine also attracted attention to it as a potential source of both magnesium compounds and as a source of metallic magnesium (Bengston, 1956; Hunter, 1941). Industries using olivine have not standardized specifications. Normally, producers supply a product which meets individual customer requirements. Such requirements involve type and amount of impurities, grain size of product, refractory characteristics, etc. Geology Olivine occurs commonly as accessories in basic igneous and basic metamorphic rocks. Economic deposits are of magmatic origin and are restricted to essentially the dunite variety of periodotite. Dunites are medium to coarse- grained crystalline rocks, generally reddish brown on weathered outcrop, and are composed primarily of olivine.

Jan 1, 1975