Search Documents

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By V. D. O’Leary

Progress in Butte has always been marked by changes which have not only altered the physical appearance of the city, but have also greatly affected the manner and means of mining. The innovation of the Berkeley pit is an example of the former, and the introduction of blockcaving at the Kelley mine is an example of the latter. Now the camp is on the brink of another change which won't be visible on surface but will have an important impact on future underground operations. This change is known as the Deep Level Plan and has been under study for the better part of five years. In this plan all ore from the deep level mines (Mountain Con, Steward, Leonard and Belmont) will be hauled on two haulage levels, at depth, to the Kelley mine and there hoisted to surface.

Jan 11, 1963

By Pol Duwez, Paul Pietrokowsky

Titanium and vanadium form a complete series of solid solutions at temperatures above 885°C. Below 885°C, vanadium is slightly soluble in a titanium (about 1.5 pct V at 650°C) and a two-phase a plus ß region extends to 18.5 pct V at 650°C. The alloys up to 15.0 pct V transform into a supersaturated a solid solution upon rapid cooling from the ß phase. Above 15 pct V the ß phase may be retained. The temperature at which the ß to a' martensite-type transformation takes place decreases steadily from 850°C for 0.5 pct V to 325°C for 12.7 pct V. IN the transition series of the periodic table, the six elements that have a body-centered cubic structure at all temperatures, namely chromium, vanadium, molybdenum, columbium, tungsten, and tantalum, fulfill the conditions required for the existence of complete series of solid solutions with the high temperature (ß) form of titanium. Up to the present time, complete solubility at temperatures above the a to ß transformation of titanium has been observed in the systems Ti-MO,1,2 Ti-Cb,2 Ti-W,³ and Ti-Ta.³ The two remaining elements, vanadium and chromium, have atomic diameters which are not as near that of titanium as the atomic diameters of the four other elements. Both are smaller than titanium and the difference, expressed in percentage of the titanium atomic diameter, is 12.3 pct for chromium and 8.2 pct for vanadium. On this basis, the least favorable conditions for solid-solution formation are therefore encountered in the Ti-Cr system. The early work on the Ti-Cr system4 revealed that up to about 1100°C the solubility of chromium in ß titanium is limited, and an intermetallic phase exists near the stoichiometric composition TiCr2. It was found later' that a continuous series of solid solutions extends across the diagram at higher temperatures, and TiCr2 forms by solid state reaction. It became apparent therefore that complete solubility would also be present in the Ti-V system. The present investigation confirms this possibility. The iodide-refined titanium used in this investigation was purchased from the New Jersey Zinc Co., New York. According to the manufacturer, a typical analysis of this product is 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb. The Vickers hardness number (10 kg load) of the crystalline bar varies between 55 and 80. The vanadium metal was purchased from the Westinghouse Electric Corp., Lamp Div., Bloomfield, N. J. The purity of this metal is probably above 99 pct V. The oxygen content must have been quite low, since a bar about 1/4 in. square could be cold rolled into a ribbon 0.020 in. thick. To prepare the various alloys on the titanium-rich side of the diagram, the titanium rod was machined into cups 1 cm in diam and about 1.5 cm high. Pieces of vanadium, of the proper weight, were cut from the square bars and placed within the cups prior to melting. On the vanadium-rich end of the diagram, single pieces of the metals, in the proper weight pro-

Jan 1, 1953

By A. Blake Caldwell

The continental margins and ocean basins represent by far the largest unexplored frontier for discovery and development of mineral values. In April 1971, Deepsea Ventures, Inc., at a press conference in its Gloucester Point, Va. headquarters, announced what may become the first commercial deepsea venture--15,000 ft below the ocean surface. During the presentation, Deepsea's president, John E. Flipse, announced that studies made by company personnel had proven the feasibility of mining, transporting, and milling L million tpy of manganese nodules taken from the ocean floor, and that, based on current conditions and prevailing construction costs, a venture of this magnitude would cost about $200 million split evenly between mining and processing facilities. A subsidiary of Tenneco, Deepsea has tentatively reserved 1976 as the year in which it plans to mine, process and market the nodules.

Jan 1, 1971

By William B. Millar

IN ONTARIO development of the gold mines is being rapidly pushed, while the intensity of the search for new mines has probably not been equaled at any time in the past. Even to outline the results of recent prospecting activity in Ontario would be a big undertaking, but it would be timely and, I hope, interesting to Institute members to review some generalities regarding the work of the prospector and then to discuss in some detail the growth of Ontario's most promising prospect area, the Swayze district, where serious mining operations are already under way. Probably no one writing about prospectors and pros¬pecting can resist hoping that his article will not reach the eyes of a certain portion of the uninformed general public and cause a further influx of "prospective prospectors" into any given area. It is somewhat mystifying how so many people reach the conclusion that prospecting is in

Jan 1, 1933

By AIME AIME

Council.* PRESIDENT O. THE COUNCIL. JOHN HAYS HAMMOND NEW YORK, N. Y. (Term expires February, 1909.) VICE-PRESIDENTS OF THE COUNCIL. SAMUEL B. CHRISTY BERKELEY, CAL. JOHN A. CHURCH NEW YORK, N. Y. PEPSIFOR FRAZER PHILADELPHIA, PA. (Term expires February, 1909.) J. PARKE CHANNING NEW YORK, N. Y. FREDERICK W. DENTON PAINESDALE, INCH. JOHN B. FARISH DENVER, COLO. (Term expires February, 1910.)

Jan 5, 1908

Edward K. Landis, Philadelphia, Pa.: In studying Mr. Thackray's paper it seemed that a critical comparison of the results from different methods therein reported would he of interest. For this purpose Table I. was constructed by grouping all determinations made by the same method, and the probable errors were calculated. In this table all chemists titrating with permanganate (A1, E, F, G and 0 of Mr. Thackray's paper) are classed under "Emmerton;" those titrating with nitric acid (C, J, S and Y) under " Handy; " those re Probable error of result: a, ±0.0008996; b, ±0.000694; c, ±0.00107; d, ±0.00115; e, ±0.000674; f, ±0.000473; g, ±0.003675; h, ±20.0007959; i,0.000.5098; k, ±0.0008303. Probable error of single determination: a, ±0.001989; b, ±0.001547; c, ±0.00214; d, ±0.0023;e, ±0.00116;f, ±0.000818;g, ±0.0019;h, ±0.00224; i, 40.00143; k, ±0.00234. The formula for calculating the probable error is 0.6745, where N (N— 1)' S is the sum of the squares of the differences from the mean and N is the number of determinations.

Jan 1, 1897

1910, hundreds of thousands of dollars of work and equipment in a 1500-foot shaft, crosscuts and pumping had found only copper-lean pyrite in two cross- cuts, and nothing in a third. Going aimlessly along the third crosscut one day, after looking at the barren face I happened to notice a dark spot in the white limestone, near the floor on one side. I picked, and found it was a little triangle of rich chalcopyrite. Next day I took Bill Gohring, then mine superintendent, in to see it. He said nothing else had succeeded so we might as well try that. The new drift broke into a full face of high grade copper ore in the first round, and continued in rich ore for 2200 feel broken only by a couple of short stretches of lean pyrite. The earlier crosscuts had happened to cut these lean areas. Q: Was there any single thing that called your attention to that little dark spot in the side of the Briggs crosscut, rather than to any other discolored spot? Joralemon: Nothing very definite. Maybe luck, maybe that indefinable subconscious thinking that

Jan 9, 1964

(Members are urged to send in for this column any notes of. interest concerning themselves or their. fellow-members.) Members and guests who registered at Institute headquarters during the period July 10 to Aug. 10, 1914: W. B. Foote, Geneva, N. Y. John T. Beard, Temascaltepec, Mexico. E. J. Carlyle, Perm, Russia. F. H. Jackson, Alum Rock, Pa.. H. H. Bradt, Pittsburg, Pa. M. F. Sayre, Schenectady, N. Y. Dwight Furness, Guanajuato, Mexico. Prof. Robert H. Richards, past-president of the Institute, has retired as head of the Mining department of Massachusetts Institute of Technology and will engage more actively than formerly as consulting engineer in ore-dressing problems. Luther W. Kemp, who has been Metallurgist of the North Star Mines Co. at Grass Valley, Cal., has resigned to accept a position in Chile,. S. A.

Jan 9, 1914

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

Hydrogen forms a beta-stabilized system with titanium, with a beta eutectoid at about 300°C and 44 atomic pct H2. 'The solid solubility of hydrogen in alpha decreases from about 8 to about 0.1 atomic pct from 300°C to room temperature. Hydrogen has little effect on tensile properties, but decreases notch-bar toughness to a large degree. This latter effect appears to be the result of increased notch sensitivity. PRIOR to this investigation, only a small amount of information was available on the effect of hydrogen on the mechanical properties of titanium. The effects of the other interstitially soluble elements, carbon, oxygen, and nitrogen, had received detailed study. Jaffee and Campbell1 indicated that hydrogen up to 1 atomic pct did not affect tensile properties deleteriously. Pitler' indicated that 1 atomic pct H, in titanium reduced the impact strength appreciably, but his alloys contained appreciable amounts of oxygen, and it was difficult to attribute the embrittlement entirely to hydrogen. The high temperature portion of the equilibrium diagram for the Ti-H system was established by McQuillan," and his data generally corresponded with the results of Kirschfeld and Sieverts," Gibb and Kruschwitz," Bevington, Martin, and Mathews," and other investigators. The lower concentration limit of the hydride phase varied considerably among investigators, and Gibb and Kruschwitz9 ad shown that small amounts of contaminants in either titanium or hydrogen caused considerable variation in this lower limit. In view of this pronounced effect of contaminants, the extrapolated value of McQuillan's, about 48 atomic pct at the 325°C eutectoid, appeared the most reasonable. McQuillan's lowest experimental value was 54 atomic pct at a temperature of 450 °C. The density of titanium had been shown to decrease with increasing hydrogen content, but discrepancies were noted among the various investigations. The best values indicated that the density was decreased from 4.56 grams per cc at 0.27 atomic pctl to 3.84 grams per cc at 61.3 atomic pct? This investigation was conducted to determine the effects of hydrogen on a titanium, both in high purity and commercially pure metals, and on high purity a titanium alloys. Material and Fabrication The literature indicated that impurities in either the hydrogen or the titanium must be kept to a minimum. For this reason, the initial studies were made with high purity iodide-refined titanium. The vendor's analysis of the iodide titanium and the hydrogen content of the as-fabricated Y4 in. diameter rods are shown in Table I. Two 1 lb ingots were prepared by arc melting under argon in a water-cooled crucible, using a water,cooled tungsten electrode. This equipment has been described.' As-cast Brine11 hardness numbers of 88 and 58 for these ingots were low enough to insure that the high purity of the metal was maintained during arc melting. The ingots were hot forged to % in. diameter rods at 800°C, cleaned by grit blasting, and then cold swaged to Yz in. diameter rods. The rod was then air annealed at 725 "C, ground to remove scale, and cold swaged to Y4 in. diameter (75 pct reduction in area). The material was then annealed for 1 hr in argon at 800°C to develop an equiaxed a grain size of about 0.05 mm. Micro tensile specimens and microimpact specimens were machined from this rod prior to treatment in the Sieverts-type absorption apparatus. Two lots of commercially pure RC-55 titanium were also used in this investigation to determine the effects of hydrogen and the normal impurities on mechanical properties. The commercially pure RC-55 alloy was obtained in the form of % in. diameter rod. The analysis of this material is also given in Table I. The % in. diameter rods were hot swaged

Jan 1, 1955

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S. 42 Broadway, New York, N. Y. '28 Barrett C. P. 5338 Harper Ave., Chicago, Ill. '28 Baum, Frank G., Cons. Hydro-Electric Engr Cassel, Shasta Co., Cal. '28 Bayless, William S. Russ Bldg., San Francisco, Cal. '28 Bean, Louis H. 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J. Room 604, 6 N. Clark St., Chicago, Ill. '28 Benwell, Oswald F. Hold Mags. '28 Beymer, Albert S., V.-P., Keystone National BankPittsburgh, Pa. '28 Blumenthal, Hugo. 44 Pine St., New York, N. Y. '28 Boettcher, Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus. Thomas H. Iola, Ken. '28 Brown, Colvin B. Chamber of Commerce Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1932

By James B. Graham, Earle E. Smith

The value of all minerals produced in the United States for the years 1930 to 1932 averaged $3,460,000,000 annually, according to Bureau of Mines reports. Of this amount, approximately $1,280,000,000 represents nonmetallic substances, such as petroleum, gas, sulfur and salt produced as fluids. Thus, about.37 per cent of the country's mineral wealth is procured through wells drilled in the earth, which require casing to keep them open throughout their life. Deep well drilling has increased greatly in the last few years. Several strings of casing have been set deeper than 9000 ft.—one, a string of 7?-in. O.D. casing, 10,301 ft. long, run in a well drilled by the Gulf Production Co. in West Texas, holds the record up to this time. These are longer strings than were contemplated when the American Petroleum Institute Specifications were adopted 10 years ago, therefore it is necessary to consider whether the present joint standards are adequate for such strings, or for even longer strings that may be called for in the future. Petroleum engineers are asking: Is there a possibility that stronger joints can be designed without going to stronger and more costly steels than offered in present specifications? Without sacrificing too greatly the tensile properties of the joint, can its design be changed to allow more clearance in the open hole below the next larger string of casing, and thus avoid costly underreaming? What can manufacturers offer for drilling through heaving shale? Fundamentals of the Problem During the last few years considerable study has been given to casing joints and their limitations, and since attention must be given to this subject by those who will be required to drill deeper holes, it is timely to review the fundamentals of the problem. These will be recognized generally as the following: 1. No threaded joint can be stronger than the area of metal under the root of the first perfect thread, and this area must be large enough

Jan 1, 1935

By James Tucker MacKeni~ie

BORN in Florida, educated in Ten¬nessee, employed all his life in the iron industry of Alabama, J. T. MacKenzie is truly of the South. In courtesy, hospitality, as well as in accent of speech, he is true to the tradition of the South. His alma neater, the University of the South, has given him the honorary degree of Doctor of Science for his achievements in metallurgy. He has been active in many technical societies; has received the Whiting Medal of the American Foundrymen's Association for his work in the advancement of gray iron metallurgy, and is chairman of the gray iron division of the A.F.A.; was instrumental in initiating the Alloys of Iron Research of the Engineering Foundation and has served as a member of its Alloys of Iron Committee since the Committee's organization.

Jan 1, 1938

PASSING over the derivation of the word as well as the description of the alum that has been written of as a liquid and that was once called natta, I tell you that the alum that is commonly called rock alum today is a congealed earthy substance, clear and transparent, of a hot and dry nature, and of a bitter taste with a certain unctuous saltiness. It has an astringent and corrosive property and is drawn from mineral stones by means of art. All that I have seen is of the same nature but of two colors,

Jan 1, 1942

By Charles L. Harness

MINERAL pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and Limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, such as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-Limonite (2Fe203.H20 to Fe203.4H20), hematite (Fe203), or magnetite (Fe203.FeO). Man's first permanent coloring materials were earth pigments- the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands

Jan 1, 1949

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By C. S. Yust, C. S. Morgan

ThIS note reports the observation of masses of dislocation etch pits around the weld necks of small single-crystal particles of calcium fluoride sintered to a cleaved face of a larger CaFz crystal. Crystal particles in the -50 +I00 mesh size range were placed on freshly cleaved CaFz surfaces and heated at 1250°C for 30 min in a tantalum container in an argon atmosphere. The sintered specimens were then etched at room temperature for 40 to 50 min in a 2 pct sulfamic acid solution which is a selective etch for dislocations in caF2.' Figs. 1 through 3 show the masses of dislocation etch pits observed around weld necks after etching. In some cases, particles were gone after removal of the specimens from the furnace although weld necks were readily visible. In other instances, no etch pits formed around a weld neck. A possible cause of concentrations of dislocations on the crystal surface is mechanical deformation of the base crystal when particles are dropped on it. If such a deformation does occur, it would be much smaller than that caused by the light punching of a crystal with a sharp instrument which results in large concentrations of etch pits. However, crystals deformed by punching with the sharp instrument and annealed at the conditions of these experiments (1250°C for 30 min) before etching showed no concentrations of dislocation etch pits. It is obvious that dislocations from the much smaller deformations, possibly created when particles are placed on the surface, would also anneal out. Etching of large crystals which had particles placed on them in the usual manner but which were not heated showed no dislocation concentrations such as shown in Fig. 1. The magnitude of dislocation etch-pit concentrations did not vary with extensive variation of the cooling rate. The appearance of many of the etch-pit clusters is typical of a well-annealed condition, indicating that the dislocation concentrations formed before the specimen temperature was lowered. Therefore, it is evident that thermal stresses in the neck area did not create the deformation indicated by the presence of the dislocations. The possibility exists that the etch-pit concentrations at places where particles had been removed may be the result of deformation accompanying the fracture of the sintered bond. That this is not so was demonstrated by breaking off particles around which no etch pits occurred. Re-etching never resulted in the large concentrations observed at sintering sites. The stress available to effect material movement during sintering of two particles will depend on the geometry at the contact point but can easily exceed the macroscopic yield stress in CaFz systems. It appears that the plastic deformation observed results from sintering or simply from the weight of the small particles. It has been previously argued that plastic flow makes an important contribution to the initial densification of oxides having the fluorite crystal structure.2p3 If plastic deformation occurs, it would begin as soon as the temperature is sufficiently high

Jan 1, 1967

By Kendall E. Born

Production of crude oil in Tennessee during 1944 was slightly more than 9500 bbl., about 1300 bbl. more than 1943. Approximately 8000 bbl. was produced from the "Mississippi lime" in Scott and Morgan Counties. Some half dozen wells in Clay, Pickett, and Fentress Counties, pumped intermittently, produced about 1500 bbl. This production is from rocks of Ordovician age ranging in depth from less than 500 ft. to approximately 1000 ft. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production of oil by counties is shown in Table I. Developments There were 20 completions during 1944 totaling 19,615 ft., nearly twice as much as in 1943. One well was drilling on Dec. 31, 1944. Of the 20 completions, one was a small oil well soon abandoned. Three gas wells were completed which are used locally. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. Cumberland Plateau There were five completions in the northern part of Cumberland Plateau. One was a small gas well in the Cooper pool 3 miles west of Oneida, but an attempt to extend the pool to the south resulted in a dry hole. The most active area in the state during 1944 was the northern Cumherland Plateau, especially in Cumberland, Morgan, and Scott Counties. Several blocks, aggregating more than 500,000 acres, were assembled and leasing was continuing in the early part of 1945. Surface work has been, or is being, carried on by at least four companies. While in an area of past oil and gas production from the "Mississippi lime," the principal interest appears to be in the essentially unexplored pre-Mississippian possibilities. The Knox dolomite group of Cambro-Ordovician age is receiving some attention as a possible reservoir. As the year closed one well was drilling on a surface structure near Lantana, 6 miles southwest of Cross-ville. This test will be drilled into the upper part of the Knox. Late in 1944, it was planned to lay a gas line from northern Morgan County to Oneida in Scott County, a distance of approximately 20 miles. Middle Tennessee Fifteen wells were drilled in Middle Tennessee. In the northeastern Highland Rim area there were 11 completions, one

Jan 1, 1945

By A. E. Gorum, I. Cornet

Fatigrle of ionic crystals has been studied primarily in magnesinm oxide. under cyclic stress dislocations move irrreversibly; they multiply; slip bands form and grow; cracks mucleate and propagnte, and failure occurs. The use of ionic crystals such as MgO is advantageorus in such investigations because they are optically transparent. Individual dislocation Intersections with {100} surfaces may be observed with a standard microscope, using etch-pit techniques. Slip, deformation, crack .formation, and fracture in MgO crystals under cyclic stress are compared with cotrresponditzg processes in metals. ThE effect of cyclic loading in metals has been studied for many years. The appearance of slip lines is readily observed and the ensuing fracture may also be seen. From these observations it is possible to predict the behavior of a material and make an educated guess as to what is happening internally, but the actual changes taking place within the structure are not readily apparent. If one could obtain a material in which the individual glide components could be observed, it would be invaluable in determining the actual slip distribution resulting from cyclic loading as well as the distribution of slip in the neighborhood of a growing crack. Such a material is magnesium oxide. Dislocation arrays may be observed by means of etch pits

Jan 1, 1961