Search Documents

By A. H. Bell

The general principles of the gas-lift will not be described in this paper. Only specific details that have not been fully discussed in previous papers, or results that do not fully coincide with conditions previously described, will be dealt with. The principal points to be emphasized and for which supporting data are furnished are as follows: 1. Gas-lift installations usually have comparatively high efficiencies as compared with standard pumping equipment, when reduced to a basis of barrels produced per horsepower installed. 2. Advantages of high-pressure plants from the standpoint of operating efficiency and for the application of the gas-lift early in the life of flowing wells. 3. Evidence of increased ultimate yield through conservation of gas by the gas-lift. 4. Possibility of development of new equipment to increase efficiency of the gas-lift. 5. Indications of the advantages of repressuring as a means of stabilizing gas-lift wells and as a means of increasing ultimate yields. TyPes of Installation The gas-lift installations of the more important companies in California have been of the central-plant type wherever field conditions would permit. This has resulted in greater flexibility and lower installation costs per well than could be obtained with individual well units. In general discussions of the gas-lift method of production, the installation costs are frequently referred to as being too high for economical operation. If the field conditions are carefully analyzed and the plant designed with the idea of obtaining high operating efficiencies, the installation cost per well can be lowered sufficiently to compare favorably with individual well-pumping units, when the operating advantages are considered. Much greater production per horsepower can be obtained with the gas-lift than is possible with pumping equipment. Table 1 shows the unit sizes and costs of gas-lift installations of three companies in the Los Angeles basin. The cost of walking beams, rods,

Jan 1, 1928

By R. E. Reed-Hill, J. L. Martin

Kinking is an important deformation phenomenon in poly crystalline a zirconium. The crjlstallo-gvaphic features of the most important form of kinking have been determined with the aid of twins formed at 77°K in grains previously kinked at high temperatures. It has been .found that the kink-band boundaries correspond to walls of edge dislocations with (1150) Burgers vectors and dislocation lines parallel to (1070). The present observations imply that basal slip is an important secondary-slip mode in polycrystalline zirconium. Previous single-crystal studies13 did not veveal this mode Other evidelzc.e for (0002)(1120) slip is also presented. ThE first studies of kinking in hexagonal metals were made by orowan,1 using single-crystal cadmium wires. He suggested that this was a new de- formation mode in metals, different from ordinary glide or twinning. Next, Hess and Barrett2 studied zinc-crystal rods in compression, and were able to offer an explanation of the phenomenon described by Orowan. They concluded that kinks required no new deformation mechanism and were a special form of deformation band that developed gradually and solely from basal glide. Similar kink bands were then observed by Washburn and parker3 on zinc crystals deformed in tension at low stresses and high temperatures. In titaniun,4 kink bands associated with {1010}<1120> prism slip have been observed in coarse-grained specimens. Magnesium5 and rhenium6 have also been observed to kink in conjunction with their basal- and {1010} prism-slip systems, respectively. Yttrium has (1010) as a predominant slip plane, but no observations of kink bands were reported.7 Since no previous investigations of kink bands in zirconium have apparently been made, this study was proposed. Its aim was to determine the crys-tallographic features of a type of kink band frequently observed in polycrystalline zirconium. EXPERIMENTAL APPARATUS All tests were performed on a type TTC Instron machine. The cross-head speed usually chosen in tension or compression was 0.02 in. per min. Ten-

Jan 1, 1964

By F. E. Wood

This paper is written primarily as a discussion of Dr. W. P. Hase-man&apos;s paper on "A Theory of Well Spacing"&apos; and presents briefly the production records, and intensity and rate of development in a large portion of the two principal producing sands in the Salt Creek field, Wyoming. The study includes 1350 wells, 160,000,000 bbl. production, well spacings varying from two to seven wells per 40 acres and early and late development. The general conclusions to be derived from this study are: 1. It is impossible to formulate a mathematical rule to apply to well spacing in the Salt Creek field. 2. Each tract is a separate problem. 3. Tracts first drilled produce the most oil, with many exceptions. 4. Initial production is not a reliable index to the relationship between past, current, or future production. 5. Wells which have produced the most oil in the past are not necessarily yielding the greatest current production nor will they yield the greatest future production. In fact, wells which have yielded the greatest past production will, in at least one-half the cases, make less oil currently or in the future than wells which have produced a smaller quantity of oil in the past. 6. The following is a safe rule to apply in well spacing in the Salt Creek field: (a) If the drilling of an additional well on a tract results in a sustained increased production, with prospects of making a profit, the tract is not overdeveloped and additional wells might be drilled. (b) If the drilling of an additional well does not effect a sustained increase in the production of a tract, the tract is fully developed. Second Wall Creek Sand The Second Wall Creek sand, covering 20,000 producing acres, is the principal producing horizon in the Salt Creek field; 1610 wells are producing at this time from this sand. This paper deals with hut a portion of the entire field including 10,680 of the more productive acres,

Jan 1, 1930

By William F. Brace, Howard R. Pratt, Wayne S. Brown

In many engineering structures, the mechanical properties of large volumes of rock must be considered. Typically, such properties are assumed to be the same as those of small laboratory samples, although it is clear that the laboratory samples do not contain the joints, faults, and other natural planes of weakness of the rock mass. A cheap, convenient testing procedure is needed with which the engineer can more accurately assess the strength and elastic properties of natural jointed rock. As a first step in this direction, a test has been developed capable of determining mechanical properties of large samples in their natural undisturbed state. In the present paper, some preliminary experiments on relatively unjointed material are described. Numerous attempts have been made to measure the deformation modulus of rock masses with varying degrees of success. Rocha (1), Grimm (2), and Alexander (3) have placed flat jacks in a slot in the rock and measured the pressure required to deform the slot. Bonnechere (4) has grouted large flat jacks in granite masses and performed similar experiments using a variety of strain measuring techniques. The U. S. Bureau of Mines has conducted radial jacking tests in which a uniform radial stress is applied to the inside of a tunnel of circular cross section and radial deformation is measured by extensometers located at various depths in the tunnel fall. Plate jack tests (Rocha (5), Shannon and Wilson (6)), pressure chamber tests, and cable jacking tests (Zienkiewicz and Stagg (7)) have all been used to determine in-situ deformation modulus. Several bore hole techniques have also been used to measure rock deformation. These include bore hole jacks (Goodman (8)), bore hole dilatometers using expandable membranes (Menard (9)) and bore hole penetrometers. Most of the above tests except the radial jacking test have an unknown stress distribution and require considerable approximation to calculate a deformation modulus. These approximations include the use of elastic theory for solutions of rigid plates, thick-walled cylinders, etc., and determination of values for Poissons

Jan 1, 1971

By Robert Mehl

RELATIVELY few data have been collected on the rates of diffusion in ternary solid solution systems. In general it does not seem worth while to gather extensive data for such systems until the factors that determine the rates of diffusion in binary systems are better understood. But the rates of diffusion in a ternary system of limited solid solubility, in which the terminal solid solution is in equilibrium with an intermediate phase and may thus be represented as a quasibinary system, represents a case of special interest. In this case, where by reason of the association of the two solute metals in an intermediate phase a special attraction of the two solute atoms may be safely assumed, some interaction of these atoms during simultaneous diffusion in the solvent lattice might be expected. It has frequently been proposed that molecular solid solutions exist in quasibinary and in other ternary (and binary) solid solutions. There is no direct evidence for such solid solutions; arguments based upon the supposed anomaly in certain physical properties1 are hardly important; unexpected density relationships have proved deceptive ;2 suggestions of molecular solid solutions have been made on the basis of solution laws in their application to certain systems, but without result;3 attempts to find lattice parameters in the solid solution Al-MgZn2, which cannot be calculated from the separate effects of magnesium and zinc and might therefore be taken as evidence for a molecular aggregation, have given negative results.4 Fundamentally, methods for the determination of the state of molecu¬lar aggregation in solution depend upon the kinetic behavior of the par-ticles constituting the system. If it could be shown that the two solutes in a quasibinary ternary system diffuse in molecular proportions, despite a radical difference in the separate rates of diffusion of each solute when diffusing alone in the solvent lattice, some basis for the concept of molecu-lar solid solution would be afforded. Freche5 examined the rates of independent and simultaneous diffusion of magnesium and silicon in

Jan 1, 1939

By C. S. Trewin

ZINC, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion, the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be determined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized,, for some time, that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade. and analyzing 0.08 per cent. lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent.

Jan 1, 1927

By B. H. Lehnhard, C. J. Cecil

The paper describes the use of the Electric Pilot in the Permian Basin for making permeability surveys of wells and for the selective acidization of wells. A general summary of the information obtained from the many permeability surveys run in this area is given, and the possible application of this information to reservoir control problems is discussed. The application of the Electric Pilot on specific wells, involving well completion, acidizing and workover operations is also included. Introduction The Electric pilot is a comparatively new tool in oil-producing areas. From the beginning, the possibilities of this new service caught the imagination of many of the oil operators and acidizing engineers. Through the continued and ever increasing use of the pilot during the past year, and the close cooperation of the oil operators who have used this service, the efficiency and utility of the Electric Pilot service has been increased to a point where it is now a well established and recognized service. There are two major uses for the Electric Pilot: (I) permeability survey; (2) selective acid treatments. Permeability surveys are made to determine the thickness of the various permeable sections at the borehole, the vertical position of these zones at the bore hole, and the relative capacities of the various zones. Nomenclature Data obtained from the permeability survey are used to calculate three different indexes that pertain to the volume of fluid injected into the various permeable zones. A nomenclature for these various indexes has been set up, which correspond with the various productivity indexes, except that they are a measure of injected fluid rather than produced fluid. The nomenclature and definition of the indexes used in connection with a permeability survey by the Electric Pilot are as follows: 1. Capacity.—The volume of water injected into an individual permeable zone, in gallons Per minute. 2. Capacity Index.—The volume of water injected into an individual permeable Zone, in gallons Per minute Per pound Per Square inch differential Pressure. 3. Specific Capacity Index.—The volume of water injected into an individual permable zone in gallons Per minute Per pound per square inch differential per foot of thickness of the zone at the borehole. Capacity is the most generally used index, and for planning initial acidizing procedures and most workover jobs it is sufficient. For comparing permeability surveys on the same well before and after

Jan 1, 1945

By Milton Williams

IT is generally recognized that fluid is lost from rotary drilling mud s to permeable strata during normal drilling operations;1,2,3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 . The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable ent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the "tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata.

Jan 1, 1939

By James J. Bean

Although determining and controlling specific gravity of operating medium in a heavy-media plant manually presents no problem, there are advantages to automatic recording and control. The two installations discussed employ the usual method of measurement. Pneumatic control with band control and reset features is used to regulate dilution water and hence specific gravity. Difficulties have been mechanical in nature and associated with obtaining a proper I sample and maintaining tight air connections in bubble-tube piping:

Jan 1, 1950

By Sanai Nakabe

Japanese wartime economy demanded domestic cobalt production. This paper describes a process operated for two years at the Besshi mine and smelter on extremely low grade (0.1 pct Co) pyrite concentrates obtained from copper ore. &apos;The steps in the process were roasting, leaching, precipitation, reduction fusion to crude cobalt, and finally refining by electrolysis to 99+ pct. COBALT ore deposits in Japan are all small and of poor grade. In the past, a small amount of cobalt has been produced from the best portions of a few of these deposits, and very little production is expected in the future. In addition to these lean cobalt ores, cobalt is present in the cupriferous pyrite which is fairly abundant although of low grade, as is shown in Table I. Considerable cobalt is expected from these deposits because of their extent. Cobalt cannot be exclusively recovered economically from ore of this type; however, if means could be devised to recover it as a byproduct of copper production, a fairly large production at reasonable cost could be expected from Japanese sources. It was along this line that the research work was done. Selection of Suitable Process The process for extracting cobalt differs from ore to ore according to their composition. The difficulty in cobalt metallurgy arises from the fact that chemically cobalt resembles many such common metals as Mn, Fe, Ni, Cu, and Zn, associated with it in the ores. In the present case the most serious difficulties were: 1—Extremely low grade ore, 0.1 pct Co. 2—The large proportion of iron accompanying cobalt and its close similarity in chemical behavior. 3—The fairly large proportion of zinc and manganese and their chemical similarity to cobalt. The recovery of cobalt oxide as a byproduct of the hydrometallurgy of copper had been attempted in Japan but was stopped after a short period because it proved uneconomical. The literature disclosed no method for the recovery of cobalt from cobaltiferous copper pyrite and it was therefore necessary to devise a new process. The following basic principles were considered in selecting the process: 1—A major alteration in copper production methods should not be necessary. 2—The first step should be the extraction of cobalt leaving the large quantity of iron unaffected. For this purpose wet metallurgy would be preferred.

Jan 1, 1952

By F. M. Lewis, J. F. Myers

The crushing of ore, as defined by Taggart, is "usually a stage process, utilizing . . . machines especially suitable for the reduction of particular sizes. . . . down to a final stage, employed for the reduction of the finest sizes. ... In contradistinction, comminution to 20-mesh or finer is called grinding. There is a twilight zone in which the product is 6, 10, or 14-mesh limiting size which is either crushing or grinding. ..." Since the data in this paper pertain to a rod-mill operation, comminuting a particular ore size of ¾ in. to a final stage, coarser than 20-mesh, the rod mill is designated as a "fine crusher machine" in this paper. The published literature discloses a wealth of data regarding a rod mill as a fine-grinding machine but relatively little as a fine-crushing operation. Typical of the latter operation is: (I) a description by F. J. Tuck2 in which a fine-crushing rod mill replaced crushing rolls and (2) a description by the present authors3 in which a fine-crushing rod mill was installed instead of a collventional fine-crushing machine. The experience of the authors is that a definite distinction must he made between the rod mill functioning as a fine crusher and as a fine-grinding machine. As a fine crushing machine it prepares relatively large amounts of ore for a subsequent fine grinding operation; as a grinding machine, it grinds relatively small amounts of ore to some predetermined finished product. Pulp Movement and Action in Mill In considering the work performed by a fine-crushing rod mill, it seems important to understand just what takes place within the mill. We were inspired to study this matter by a paper by E. W. Davis,4 which indicated that definite water classification of ore particles took place in a ball mill. However, in thinking of the rod-mill action from this point of view, we were confronted with the fact that our rod-mill discharge product showed no evidence of action by water classification. The Tennessee Copper Co. ore is relatively high in sulphides, and the gangue rock and the sulphides are of about the same hardness. In the presence of any action by classification, the coarser sizes are definitely very lean in sulphide minerals.

Jan 1, 1947

By J. F. Myers, F. M. Lewis

The crushing of ore, as defined by Taggart, is "usually a stage process, utilizing . . . machines especially suitable for the reduction of particular sizes. . . . down to a final stage, employed for the reduction of the finest sizes. ... In contradistinction, comminution to 20-mesh or finer is called grinding. There is a twilight zone in which the product is 6, 10, or 14-mesh limiting size which is either crushing or grinding. ..." Since the data in this paper pertain to a rod-mill operation, comminuting a particular ore size of ¾ in. to a final stage, coarser than 20-mesh, the rod mill is designated as a "fine crusher machine" in this paper. The published literature discloses a wealth of data regarding a rod mill as a fine-grinding machine but relatively little as a fine-crushing operation. Typical of the latter operation is: (I) a description by F. J. Tuck2 in which a fine-crushing rod mill replaced crushing rolls and (2) a description by the present authors3 in which a fine-crushing rod mill was installed instead of a collventional fine-crushing machine. The experience of the authors is that a definite distinction must he made between the rod mill functioning as a fine crusher and as a fine-grinding machine. As a fine crushing machine it prepares relatively large amounts of ore for a subsequent fine grinding operation; as a grinding machine, it grinds relatively small amounts of ore to some predetermined finished product. Pulp Movement and Action in Mill In considering the work performed by a fine-crushing rod mill, it seems important to understand just what takes place within the mill. We were inspired to study this matter by a paper by E. W. Davis,4 which indicated that definite water classification of ore particles took place in a ball mill. However, in thinking of the rod-mill action from this point of view, we were confronted with the fact that our rod-mill discharge product showed no evidence of action by water classification. The Tennessee Copper Co. ore is relatively high in sulphides, and the gangue rock and the sulphides are of about the same hardness. In the presence of any action by classification, the coarser sizes are definitely very lean in sulphide minerals.

Jan 1, 1947

By W. H. Andrews

The constantly increasing consumption of Portland cement in the State makes the above subject of particular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case it may be well at this time to consider briefly the matter of the chemical and physical composition of proper raw materials. A cement mixture is one that contains approximately 75 per cent, carbonate of lime, 15 per cent. silica, and 5 to 7 per cent. alumina and iron oxides; the other elements being magnesium carbonate and mall quantities of the rarer elements generally associated with limestone deposits. It can be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.—A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina ratio lies between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or hales are often found that have the proper physical characteristics but in which the amount of alumina is too great. Second.—A mixture can be built up of different limestones some of which run above the 75 per cent. requirement and others below;

Jan 1, 1914

By S. P. Burke

OUTBURSTS in coal mines have contributed greatly to the hazard of mining operations in localities in which they occur. They have been responsible for many casualties and fatalities and much property damage. An excellent review and symposium on the subject appeared recently1. From a study of the papers included in this symposium, and other litera-ture on this subject2, the following conclusions or statements seem justified: 1. Outbursts are more likely to occur in deep mines; that is, where the coal seam being mined has considerable overburden. 2. Outbursts usually occur when hard, dense, nonfractured coal is being mined. It is believed that in most cases a fault or a pocket of friable or soft or pulverized coal existed some distance behind the dense coal at the time of the outburst. 3. The outburst involves a rending or pushing of the solid material of the coal face, the roof, or the floor outwards and often is accompanied by the discharge of large quantities of very fine coal. 4. Drill holes or borings into the coal ahead of the workings have failed to yield information either from evidence of increased gas pressure or increased gas flow that makes possible the prediction of outbursts. 5. Mines in which outbursts occur are usually considered "nongassy," or only very slightly "gassy"; yet large volumes of gas may be produced at the time of the outburst. Despite the varied conditions and varied locations in which outbursts have occurred, the foregoing general statements appear to be applicable in whole or in part to all the recorded cases. These observations there-fore should be significant and any explanation of the mechanism of the phenomena should be consistent with them. The following suggestion seems to be in accord with this requirement, and is offered in the hope that it may assist in the further elucidation of this phenomenon.

Jan 1, 1935

On August 4, 1844, J. C. Fremont made the first record found of coal in Wyoming. On the North Fork of the Platte River, beyond Medicine Butte, in Carbon County, he noted: "in the precipitous bluffs were displayed a succession of strata containing fossil, vegetable remains, and several beds of coal. In some of the beds, the coal did not appear to be perfectly mineralized; and in some of the seams, it was compact and remarkably lustrous." A little later he noted, "longitude 111°, latitude 4 1/2°-Muddy R.--coal."1 In 1848, Clayton reported coal on Sulphur Creek near the site of old Bear River City, in Uinta County.2 Maj. Osborne Cross in his journal, on July 1, 1849, records seeing coal on Deer Creek and in one of the hills near Crooked Muddy Creek, in Converse County; on July 7, he records that the country from Deer Creek to the Sweetwater River abounds in coal, probably in Natrona and Carbon Counties.3 A letter from Asst. Quartermaster Van Vliet to General Jessup dated July 25, 1850, asked an appropriation for building shops at Fort Laramie for making repairs for the emigrants, and mentions "coal and timber," but undoubtedly meant charcoal, as no other mention of stone coal is made in the records of the fort.4 Stansbury, in 1852, placed on his map of this section the words: "Great Coal Basin," extending from the west bank of Bear River, near the present Evanston, to Point of Rocks in Sweetwater County. In 1859, a military coal reservation was established near here, but the coal was never worked to any great extent, although probably some was hauled to Fort Bridger for smithing purposes. When the fort was abandoned this reservation returned to the public lands .2 In the same year (1859), Hayden traced the lignite formation uninterruptedly from the upper Missouri Valley to a point on the North Platte River, about 80 miles northwest of Fort Laramie.5 On August 25, 1865,

Jan 1, 1942

By Hugh Douglas

ANTIMONY Antimony (Sb) has been used since the early Egyptian dynasties. Prior to World War I, total demand amounted to only 6000 to 7000 tons per year (tpy). Wartime uses and rapid rise of industrialization in the Northern Hemisphere nations have pushed world antimony use to the 78,000-tpy level. An overwhelming supply of low-cost antimonial resources in the Sino-Russian bloc countries has and will continue to have a major impact on availability and price to users outside the bloc. Table 14.4.1 shows trends in world production, United States production and consumption, and prices. Demand Antimony is used principally as an alloy in lead-based metals and other alloys. Pure metallic antimony usage is small and is confined to such areas as laboratory and electronic applications. Lead-antimony alloys are used in automobile storage batteries, chemical pumps, and pipes, tank linings, roofing material, and cable sheaths. The metal increases the hardness of lead, and, for such uses as foundry printing type, reduces shrinkage for casting and lowers the melting point. Antimonial oxides are used for ceramic purposes, white paint pigments, glass forming, textile finishing, fire retardants in military clothing, matches, and solder. Wartime applications include use as hardener for bullets, an element for tracer bullets, and ingredient for producing dense white smoke for visual markers. A small but rapidly growing use for antimony is for metallic compounds in semiconductors and thermoelectric devices. In the United States demand for antimony is about evenly divided between metallic end-use markets and nonmetallic markets. In metallic end uses, antimonial lead accounts for 27% of total metallic and nonmetallic use; in nonmetallic areas major uses are flame retardants (15%) which is the fastest growing market, plastics (13 % ), and ceramics and glass (11%). While antimony has advantages in most of its applications, there are uses in which other materials can be substituted, including: mercury, titanium, lead, zinc, chromium, tin, and zirconium in paints and pigments; tin in sheathings; calcium in battery plates; and bismuth in type metal. Supply Antimony is produced from both antimony ores and as a byproduct of smelting other ores. The principal ore mineral is stibnite (Sb2S3), along with its oxidized antimonial minerals and derivatives which occur in small discontinuous replacement veins or fissure vein implacements. Stibnite occurs in quartz-gold veins and copper-lead-zinc

Jan 1, 1976

By Robert M. Asimow, Bisuddhi Riddhagni

THE use of back-reflection Laue photographs for crystal orientation is standard in many research projects. The time required for the orientation of any given crystal depends largely on luck and the skill of the investigator. In any case, where large numbers of crystals are used, this time can be quite considerable when the standard methods involving a Greninger chart and Wulff net are employed. For this reason the technique described below was developed. This new procedure applicable for cubic crystals (without preparation of new charts) largely eliminates the skill and luck factors and makes possible the determination of orientation in minutes. The procedure works in the following way: the Laue photograph is examined and arbitrarily an important hyperbola is picked out. An important hyperbola is defined as one which contains some spots through which several hyperbolas pass. Such a hyperbola inevitably corresponds to a low-index zone axis. The angles between the reflection planes causing all the spots on this hyperbola can be read directly from a Greninger chart in the usual manner. If the hyperbola contains more than five spots, these interplanar angles will positively identify the zone axis and the indices of each of the reflecting planes. However, initially since neither the zone axis nor the Miller indices of a diffraction spot are known, there are a very large number of possibilities that must be considered. Using tables of interplanar angles to check out every possibility would be quite tedious, so that this approach is not generally used. Instead, various poles are plotted on a stereographic projection. In the cubic system, however, it is possible to plot out once and for all the angles between all planes of a particular zone axis up to some upper limit of Miller indices. This has been done for all low-index zone axes in Fig. 1. Given these charts, it is quite a simple matter to identify the spots of the unknown hyperbola. All that is necessary is to plot the angles read off the Greninger chart to the same scale as Fig. l(b) on a strip of paper. Then this strip can be slid along each zone axis of Fig. l(a) until a good fit is obtained. Once this is accomplished, the Miller indices of each spot are given and thus the orientation problem is solved. To check, it is possible to pick a second hyperbola and see whether a compatible solution is obtained. This is most conveniently done by picking for the second hyperbola one that contains a spot common with the first. If the specimen axis is chosen parallel to the incident X-ray beam, then usually the [ loo] hyperbola will appear on the film as one of the more important hyperbolas and consequently will be either chosen initially or as a check. Using the [100] hyperbola, after the (001) or (011) spots have been identified, the latitude and longitude of the specimen axis can be read directly from the Greninger chart so that it is unnecessary to use a Wulff net for the entire orientation procedure. This makes the operation not only quicker but more accurate. Of course, if neither the first nor second hyperbolas correspond to [loo] then a third hyperbola can be chosen.

Jan 1, 1967

Arizona E. P. MATHEWSON, Chairman F. W. MACLENNAN, First Vice-chairman CLYDE E. WEED, Second Vice-chairman E. D. GARDNER, Secretary-Treasurer Box 4097, University Station, Tucson, Ariz. I. H. BARKDOLL HENRY F. EASTER MICHAEL CURLEY R. D. LEISK Boston Meets first Monday each month, October to May, inclusive ROBERT S. WILLIAMS, Chairman GLEN F. JENKS, Vice-chairman F. LEROY FOSTER. Secretary-Treasurer Rooms 6-202, Mass. Inst. of Tech., Cambridge, Mass. HOLCOMB J. BROWN ESPER S. LARSEN

Jan 1, 1936

By John A. Church

The operations of the Tombstone Mill and Mining Company, in Arizona, have been extensive and interesting; and I will eudeavor to describe what is novel in their work, without attempting to go over the well-known facts of silver milling, concentration and smelting which are the general branches of their business. Their mines are at Tombstone, and their mills at Charleston, ten miles distant. The ore has been mined only above water-level, and at first was

Jan 1, 1887

By J. R. Campbell

In order to discuss the subject intelligently, it will be necessary to touch briefly on the forms in which sulphur is supposed to exist in coking coal to be carbonized in beehive or byproduct ovens. Sulphur is known to exist in coal as sulphides and sulphates, as can be determined experimentally. Then there is the so-called organic sulphur, i.e., sulphur in combination with the carbon, &apos;hydrogen, and oxygen of the coal, about which much has been written, but nothing definitely proven in an experimental way. In fact, so far. as we know, there never has been developed a satisfactory and conclusive method in the laboratory for the direct determination of organic sulphur. For most coking coals, it can be safely assumed that the preponderance of sulphur is in the form of pyrite (FeSz). When exposed to comparatively low temperatures during the coking process, it loses its sulphur according to the following chemical reaction: 7FeS2 = Fe7Ss + 6S. It will be seen, therefore, that six out of the 14 atoms of sulphur (or 42.8 per cent.) are expelled, or volatilized. FelSa remains in the coke as pyrrhotite, or magnetic sulphide of iron; this accounts for the highly magnetic properties of the powdered coke. A more commonly accepted reaction is FeS2 = FeS f S, in which the straight sulphide of iron is produced with 50 per cent. volatilization of sulphur. In the beehive methods of coke making, air is introduced in sufficient amounts to carry on the distilling and the coking processes, and the sulphur is oxidized along with the other volatile products: First, into sulphur dioxide (SO2), known by the pungent andsuffocating odoremitted from the trunnel head; second, into sulphuric anhydride (SOa); and, finally, into sulphuric acid, as it comes into contact with the air and moisture. In a properly regulated draft on a beehive oven, there is never complete combustion of the gases. In other words, the coking process should be carried on in a reducing atmosphere, and a low-grade producer gas kept issuing from the trunnel head. For coals of about 30 per cent. volatile matter, the ratio of air to gas is 3½ to 1. In complete combustion, the ratio is 6 to 1, producing an extremely high temperature

Jan 1, 1916